Interface Dot11Radio0 cannot associate: No Response

Having an issue with a non-root bridge communication with the root device getting the error message -
*Mar 1 12:55:34.159: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: No Response
*Mar 1 12:55:46.159: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Rcvd response from 6cfa.8918.12e0 channel 3 3240
*Mar 1 12:57:01.159: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Authenticating
*Mar 1 13:02:59.159: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Associating
I believe the issue may be down to the SSID but can't see what's wrong with the config any Ideas?
config of the WAP is -
Current configuration : 2074 bytes
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname UKPA
logging rate-limit console 9
enable secret 5 $1$y65O$Duk6tL2w8VxpeSkH9WIWu/
no aaa new-model
no ip cef
dot11 syslog
dot11 ssid BRIDGE
   vlan 182
   authentication open
   authentication key-management wpa
   guest-mode
   wpa-psk ascii 7 c942cc494622b70e126618c19eb768ee6fc8ded892204e7367b42384168f15c1
dot11 guest
username Cisco password 7 047802150C2E
bridge irb
interface Dot11Radio0
no ip address
encryption vlan 182 mode ciphers aes-ccm tkip
ssid BRIDGE
antenna gain 0
packet retries 64 drop-packet
station-role non-root
bridge-group 1
bridge-group 1 spanning-disabled
interface Dot11Radio0.182
encapsulation dot1Q 182
bridge-group 182
bridge-group 182 subscriber-loop-control
bridge-group 182 spanning-disabled
interface Dot11Radio1
no ip address
shutdown
antenna gain 0
peakdetect
no dfs band block
packet retries 64 drop-packet
channel dfs
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface GigabitEthernet0
no ip address
duplex auto
speed auto
bridge-group 1
bridge-group 1 spanning-disabled
interface GigabitEthernet0.182
encapsulation dot1Q 182
bridge-group 182
bridge-group 182 spanning-disabled
no bridge-group 182 source-learning
interface GigabitEthernet1
no ip address
duplex auto
speed auto
bridge-group 1
bridge-group 1 spanning-disabled
interface BVI1
ip address 10.182.22.11 255.255.128.0
ipv6 address dhcp
ipv6 address autoconfig
ipv6 enable
ip default-gateway 10.182.1.1
ip forward-protocol nd
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
line con 0
line vty 0 4
login local
transport input all
end

Hi Paul,
Info: Point to remember is Non-Root Bridge to be connected to Root Bridge via native vlan SSID in order to carry multiple WLAN(or vlans) through this wireless bridge.
Try this:
interface Dot11Radio0.182
encapsulation dot1Q 182 native
bridge-group 1
interface GigabitEthernet0.182
encapsulation dot1Q 182 native
bridge-group 1
To know more, please check this:
https://rscciew.wordpress.com/2014/10/26/autonomous-ap-as-wireless-bridge/
Regards
Don't forget to rate helpful posts

Similar Messages

Interface Dot11Radio0, cannot associate: No matching SSID

Hi all, I have a problem with a P2P Bridge with a couple of Aironet 1242AG.
Sometimes this Bridge goes down, and if I change Channel, it goes up.
When Bridge is down I can see this log in NoRoot:
*Apr 23 04:12:20.002: %DOT11-4-UPLINK_ESTABLISHED: Interface Dot11Radio0, Associated To AP XXXX-Root 0014.1b60.9230 [None WPA PSK]
*Apr 23 04:12:20.003: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Apr 23 04:12:20.008: %DOT11-4-UPLINK_DOWN: Interface Dot11Radio0, parent lost: authenticate response status (12) denied
*Apr 23 04:12:20.069: %DOT11-4-UPLINK_ESTABLISHED: Interface Dot11Radio0, Associated To AP XXXX-Root 0014.1b60.9230 [None WPA PSK]
*Apr 23 04:12:20.079: %DOT11-4-UPLINK_DOWN: Interface Dot11Radio0, parent lost: Received deauthenticate (2) not valid
*Apr 23 04:12:20.081: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
*Apr 23 04:12:31.049: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: No matching SSID
*Apr 23 04:13:32.392: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Rcvd response from 0014.1b60.9230 channel 6 3669
*Apr 23 04:18:46.404: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Authenticating
*Apr 23 04:30:18.666: %DOT11-4-UPLINK_ESTABLISHED: Interface Dot11Radio0, Associated To AP XXXX-Root 0014.1b60.9230 [None WPA PSK]
*Apr 23 04:30:18.666: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
I can see this log in Root:
7w4d: %DOT11-7-AUTH_FAILED: Station 001c.f663.1110 Authentication failed
7w4d: %DOT11-4-MAXRETRIES: Packet to client 001c.f663.1110 reached max retries, removing the client
7w4d: Client 001c.f663.1110 failed: reached maximum retries
7w4d: %DOT11-7-AUTH_FAILED: Station 001c.f663.1110 Authentication failed
I don't understand "No matching SSID" and authentication error, the Wpa-psk and Ssid are the same.
Do you have idea? I suppose a RF problem.
Regards

Hi,
The "no matching SSID" appears when your non-root bridge tries to associate to a given SSID and does not detect any parent offering that SSID...
This seems to indicate (IMHO) a RF problem... you may want to try to monitor the link quality between your root and non root. If the signal is lots, then you would typically get this no matching SSID message while the non-root tries to reconnect without success.
Which code are you running on these APs?
Jerome

Wireless Bridge error with AIR-BR1310G-E-K9,cannot associate: No response

Hi Guys,
I have to do a wireless bridge with 2 AIR-BR1310G-E-K9. I configure 1 AP root bridge and 1 AP non-root bridge, with the same SSID.
But on the AP non-root bridge, the interface dot11 radio don't change it state to up and give this error: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: No Response.
I don't why it doesn't work. Even if i try a configuration which it already work on a site, it doesn't work to.
So I ask to me if there is a problem with internal antenna?
If I configure the 2 AP to access point role with 2 different ssid, I can see the 2 ssid but with a weak signal.
This AP can work without external antennas?
Thanks for your help

Hi Jerome,
The 1310 definitely can work with the internal antenna but... is the AP mounted somewhere? Some mounting options imply an external antenna as they position the internal antenna toward the wall...

1602 AP - Workgroup Bridge Cannot Associate to Parent AP

Hi All,
For a few weeks now, I have been trying to connect a Cisco 1602 standalone AP to our unified wireless network as a workgroup bridge. Eventually this AP is to be moved to another wireless network where I will need it to run in universal workgroup bridge mode (for non Cisco wireless networks), so I just want to get this working in the office before I take it elsewhere and try to get that to work, as the configuration will be similar.
So far I've been unable to get this 1602 AP to associate to our network. The particular SSID I'm trying to set up is a BYO style SSID, normally if you connect a device you provide your Active Directory username / password and your laptop / phone / whatever connects. I know the username is fine because if I use it on another device it's not a problem.
The AP keeps repeating this message: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Associating. Cisco.com tells me that this is to do with MFP, however I've changed a number of MFP settings in the SSID and this seems to have made no difference.
I'm thinking this is a problem with authentication or association. I have a question, why do I need to input Radius server information into the config (eap_methods)? When you connect a regular device to this SSID it doesn't require any Radius server settings in order to connect, I don't understand why the AP needs these settings. Also, when authenticating to AD, do you need to include the domain name as part of the username?
Wireless isn't my strong point unfortunately. Is anyone able to help with this? Config and log is below. Many thanks.
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname WGB-AP
logging buffered 10000
logging rate-limit console 9
enable secret 5 xxxx
aaa new-model
aaa user profile userprofilename
aaa group server radius rad_eap
aaa group server radius rad_mac
aaa group server radius rad_acct
aaa group server radius rad_admin
aaa group server tacacs+ tac_admin
aaa group server radius rad_pmip
aaa group server radius dummy
aaa authentication login eap_methods group rad_eap
aaa authentication login mac_methods local
aaa authorization exec default local
aaa accounting network acct_methods start-stop group rad_acct
aaa session-id common
no ip routing
no ip cef
dot11 syslog
dot11 ssid BYO
authentication open eap eap_methods
authentication shared eap eap_methods
authentication network-eap eap_methods
authentication key-management wpa version 2
dot1x credentials MyCreds
dot1x eap profile EAPTLS
infrastructure-ssid
ids mfp client optional
eap profile EAPTLS
method mschapv2
method peap
crypto pki token default removal timeout 0
crypto pki trustpoint TP-self-signed-88743315
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-88743315
revocation-check none
rsakeypair TP-self-signed-88743315
crypto pki trustpoint WGB-PEAP
enrollment terminal
subject-name CN=username
revocation-check none
rsakeypair manual-keys 1024
crypto pki certificate chain TP-self-signed-88743315
certificate self-signed 01
30820227 30820190 A0030201 02020101 300D0609 2A864886 F70D0101 05050030
2F312D30 2B060355 04031324 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 38383734 33333135 301E170D 39333033 30313030 30383234
5A170D32 30303130 31303030 3030305A 302F312D 302B0603 55040313 24494F53
2D53656C 662D5369 676E6564 2D436572 74696669 63617465 2D383837 34333331
3530819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281 8100BB10
F5361E52 A573FE8A 247142AD CF53D762 38F7BB42 7E723B2B 5C78100E 7F312442
3BE63A8B 7E826758 3F2914D0 4BBC93A6 CCACA795 927514E7 74561589 444D03BA
C20B80D8 85E52A18 C3B287BF 4A1EEF83 B43DD673 12BF075F 7CA038C0 C31F1FB4
F75C3F86 C09DC703 FB05676B 16B86754 F0F11D4D 36B61F81 DF15C02A 9C410203
010001A3 53305130 0F060355 1D130101 FF040530 030101FF 301F0603 551D2304
18301680 14999B3B 7F4B10FA B95CC90B D7218636 39280AFE 4E301D06 03551D0E
04160414 999B3B7F 4B10FAB9 5CC90BD7 21863639 280AFE4E 300D0609 2A864886
F70D0101 05050003 81810076 27E215C4 C105C66D 15124645 D3F4A538 F977A95F
7AF0FF05 648D41A4 A796F9CB CC6327FF 726DA1D6 290CD438 C2111DF8 208B92B5
63B09FEC 1CA334F7 A4607E71 18EBCB44 0A175BEE 30689849 B4D9222E 7EB1C1DB
F36BDDD3 3F5514A6 8A006A8A A113A44D 7337B6D8 7860AA25 EBAD5588 8543DF88
9E6A3D62 6E875372 277B57
quit
crypto pki certificate chain WGB-PEAP
dot1x credentials MyCreds
username DOMAIN\AD-USER
password AD Password
username Cisco password 7 00271A150754
username DOMAIN\AD-USER
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers aes-ccm
ssid BYO
antenna gain 0
stbc
beamform ofdm
station-role workgroup-bridge
bridge-group 1
bridge-group 1 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
shutdown
encryption mode ciphers aes-ccm tkip
ssid BYO
antenna gain 0
no dfs band block
channel dfs
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
bridge-group 1
bridge-group 1 spanning-disabled
interface BVI1
no ip address
no ip route-cache
ip forward-protocol nd
no ip http server
ip http authentication local
ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
ip radius source-interface BVI1
radius-server attribute 32 include-in-access-req format %h
radius-server host xxxx auth-port 1812 key 7 xxxx
radius-server vsa send accounting
bridge 1 route ip
line con 0
logging synchronous
line vty 0 4
transport input all
end
Jan 5 14:34:30.636: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Associating
Jan 5 14:36:23.730: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Associating
Jan 5 14:36:42.730: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Associating
Jan 5 14:38:19.833: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Associating
Jan 5 14:39:33.901: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Associating
Jan 5 14:40:49.948: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Associating
Jan 5 14:42:10.123: %SYS-5-CONFIG_I: Configured from console by console
Jan 5 14:42:42.031: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: No Response
Jan 5 14:42:46.031: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Associating
Jan 5 14:43:06.058: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Associating
Jan 5 14:45:18.173: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Associating

With PEAP there is a certificate being used on the radius server for securing the first phase (outer tunnel). In this scenario the access-point acts like a dot1x client, so like any other client it has to validate the certificate the radius server uses. Therefor the root certificate (and intermediates, if being used) needs to be installed on the access-point.
I never configured an WGB in this way, so I fired on my lab to see if I could get it to work. Sadly I did not manage to get it to work properly, I'm running into "EAP session timed out" messages in ACS (my radius server). I did also ran into the MFP issue, but as long as you configure MFP as optional on the network side, it should work. Because of the CCIE exam, I'm running old AirOS software on the WLC and also the software on the access-point I tested this configuration on (2600) is not that new. So it could be that I ran into a bug testing this, so I would advise you to run the latest software on your 1600. There are WGB related bugs fixed not so long ago. This configuration is supported since IOS 15.2.2(JA) and higher.
If I look at your configuration you still need to actually install the certificate, the trustpoint is empty. Besides that the following configuration changes needs to be made:
eap profile EAPTLS
no method mschapv2
method peap
dot11 ssid BYO
authentication open eap PEAP
   no authentication shared eap eap_methods
authentication network-eap PEAP
authentication key-management wpa version 2
dot1x credentials MyCreds
dot1x eap profile EAPTLS
   no infrastructure-ssid
   no ids mfp client optional
For more information look at this document.

Cannot Associate 1532 Bridges in Non-Root role

Hello,
Can someone please tell me what I am missing and why I cannot bring up 2 bridges in "Root" and "Non-Root" roles?
I have similarly configured bridges in a Root / Non-Root role several times before with older AP's and never had any issues... although it was always just 1 SSID, 1 Vlan, and no subinterfaces...
The only way I was able to get these 2 bridges to associate was to put the Non-Root bridge into a Workgroup Bridge role and then *BANG* everything worked perfectly. I tried getting rid of the authentication and tried using the Parent command but neither helped. Prior to entering Station Role Workgroup Bridge, the only message I would receive was showing on the Non-Root side and all it said was:
*Mar 1 07:27:13.867 GMT: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: No Response
*Mar 1 07:27:28.891 GMT: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Rcvd response from 544a.0005.8030 channel 3 2815
What am I missing or what have I incorrectly configured on my Non-Root config?
Bridges are both 1532i with the Autonomous Image 15.2(4)JB5
Attached are the configs prior to changing the Non-Root AP to a station role of Workgroup Bridge.
Thanks!

Hi,
This should work with multiple sub-interfaces.
Few more suggestions
1. Remove this from your BRIDGE SSID & check
mobility network-id 1
This is only require when you configure L3 roaming & WDS in place.
http://www.cisco.com/c/en/us/support/docs/wireless/aironet-1200-series/8103-ap-faq.html
2. Try to set WPA version 2 & only AES encryption.
Also try to Associate your Bridges using Open Auth first (as shown in my blog post initial section) & then try to add security.
HTH
Rasika
**** Pls rate all useful responses ****

Cannot associate: No matching privacy setting

I am trying to create a wireless bridge with 2 1200 AP.
The "Client" is giving me this error message:
Interface Dot11Radio0, cannot associate: No matching privacy setting (from 001b.d5c8.ce80)
This is the master config:
version 12.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname Bclap-ad01
enable secret xxx
ip subnet-zero
aaa new-model
aaa group server radius rad_eap
server 172.30.103.178 auth-port 1812 acct-port 1813
aaa group server radius rad_mac
aaa group server radius rad_acct
aaa group server radius rad_admin
aaa group server tacacs+ tac_admin
aaa group server radius rad_pmip
aaa group server radius dummy
aaa authentication login eap_methods group rad_eap
aaa authentication login mac_methods local
aaa authorization exec default local
aaa accounting network acct_methods start-stop group rad_acct
aaa session-id common
dot11 ssid Wireless-Bridge
authentication open
dot11 network-map
username Cisco password xxx
bridge irb
interface Dot11Radio0
description 802.11G Radio
no ip address
no ip route-cache
ssid Wireless-Bridge
speed basic-1.0 basic-2.0 basic-5.5 basic-11.0
station-role root access-point
rts threshold 2312
antenna receive right
antenna transmit right
antenna gain 14
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
shutdown
speed basic-6.0 9.0 basic-12.0 18.0 basic-24.0 36.0 48.0 54.0
station-role non-root
bridge-group 1
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
bridge-group 1
bridge-group 1 spanning-disabled
interface BVI1
ip address 172.30.103.178 255.255.0.0
no ip route-cache
ip default-gateway 172.30.4.70
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
ip radius source-interface BVI1
radius-server local
nas 172.30.103.178 key xxx
user Chapais-AP nthash xxx
radius-server attribute 32 include-in-access-req format %h
radius-server host 172.30.103.178 auth-port 1812 acct-port 1813 key xxx
radius-server vsa send accounting
control-plane
bridge 1 route ip
line con 0
line vty 0 4
end
This is the client config:
Can you help me find the error in my setup ?

This has to do with mismathced encryption setting on the client and access point. Make sure encryption setting match. Refer URL
http://cisco.com/en/US/docs/wireless/access_point/12.4_3g_JA/configuration/guide/s43auth.html#wp1035522

Error in CLR: InvalidOperationException - The current type is an interface and cannot be constructed. Are you missing a type mapping?

Hi, I'm trying to execute a .NET assembly's method from SQL Server 2012 Express, but I'm stuck with this error calling the sp:
Microsoft.Practices.ServiceLocation.ActivationException: Activation error occured while trying to get instance of type ISymmetricCryptoProvider, key "TripleDESCryptoServiceProvider" ---> Microsoft.Practices.Unity.ResolutionFailedException:
Resolution of the dependency failed, type = "Microsoft.Practices.EnterpriseLibrary.Security.Cryptography.ISymmetricCryptoProvider", name = "TripleDESCryptoServiceProvider".
Exception occurred while: while resolving.
Exception is: InvalidOperationException - The current type, Microsoft.Practices.EnterpriseLibrary.Security.Cryptography.ISymmetricCryptoProvider, is an interface and cannot be constructed. Are you missing a type mapping?
At the time of the exception, the container was:
Resolving Microsoft.Practices.EnterpriseLibrary.Security.Cryptography.ISymmetricCryptoProvider,TripleDESCryptoServiceProvider
---> System.InvalidOperationException: The current type, Microsoft.Practices.EnterpriseLibrary.Security.Cryptography.ISymmetricCryptoProvider, is an interface and cannot be constructed. Are you missing a type mapping?
System.InvalidOperationException:
   en Microsoft.Practices.ObjectBuilder2.DynamicMethodConstructorStrategy.ThrowForAttemptingToConstructInterface(IBuilderContext context)
   en BuildUp_Microsoft.Practices.EnterpriseLibrary.Security
Microsoft.Practices.ServiceLocation.ActivationException:
   en Microsoft.Practices.ServiceLocation.ServiceLocatorImplBase.GetInstance(Type serviceType, String key)
   en Microsoft.Practices.ServiceLocation.ServiceLocatorImplBase.GetInstance[TService](String key)
   en Microsoft.Practices.EnterpriseLibrary.Security.Cryptography.Cryptographer.GetSymmetricCryptoProvider(String symmetricInstance)
   en Microsoft.Practices.EnterpriseLibrary.Security.Cryptography.Cryptographer.DecryptSymmetric(String symmetricInstance, String ciphertextBase64)
   en ...
Is there any limitation by design for Interface instantiation from CLR database?
Any help I will appreciate, thanks a million!!

Bob, thanks for your response.. Yes, the code works fine outside of SQLCLR. This is the class I'm trying to instantiate, I'm using it to envolve Cryptographer, an Enterprise Library 5.0 class actually, so I have no control to test it without referring the
interface.
using System;
using System.Collections.Generic;
using System.Linq;
using System.Text;
using Microsoft.Practices.EnterpriseLibrary.Security.Cryptography;
using System.Security.Cryptography;
using Microsoft.SqlServer.Server;
using System.Data.SqlTypes;
namespace Cars.UtileriasGlobales.Helpers
    /// <summary>
    /// Clase que permite encriptar y desencriptar cadenas de textos utilizando
    /// TripleDESCryptoServiceProvider de Enterprise Library 5.0
    /// </summary>
    public static class Cryptography
        #region Metodos
        [SqlProcedure]
        public static void DesencriptarSQLServer(SqlString cadena, out SqlString cadenaDesencriptada)
            cadenaDesencriptada = !String.IsNullOrEmpty(cadena.ToString()) ? Cryptographer.DecryptSymmetric("TripleDESCryptoServiceProvider", cadena.ToString().Replace(" ", "+"))
: String.Empty;
        #endregion
I have collected all the dependent assemblies in one directory 'C:\migrate', so the create assembly finish ok. This is the script to create the assembly I'm using:
sp_configure 'clr enable', 1
GO
RECONFIGURE
GO
ALTER DATABASE cars SET TRUSTWORTHY ON
GO
CREATE ASSEMBLY CryptographyEntLib5
AUTHORIZATION dbo
FROM 'C:\migrate\Cars.UtileriasGlobales.dll'
WITH PERMISSION_SET = UNSAFE
GO
CREATE PROCEDURE usp_Desencriptar
@cadena nvarchar(200),
@cadenaDesencriptada nvarchar(MAX) OUTPUT
AS EXTERNAL NAME CryptographyEntLib5.[Cars.UtileriasGlobales.Helpers.Cryptography].DesencriptarSQLServer
GO
DECLARE @msg nvarchar(MAX)
EXEC usp_Desencriptar 'Kittu And Tannu',@msg output
PRINT @msg

Event Log: Interface Dot11Radio0, parent lost: Had to lower data rate

Hi,
AIR-AP1242
Firmware: 12.3(8)JEB
AP -> WGB mobil station
The event log from WGB have often this warning:
%DOT!!-4-UPLINK_DOWN: Interface Dot11Radio0, parent lost: Had to lower data rate
Way?...
It is the first installation with this description.

Is the client able to associate to the AP and transfer data. This error message genrally indicate a weak signal strength or a bad link. Move the client to a different location and check if that works.

You can download past purchases on this computer with just one Apple ID every 90 days. You cannot associate this computer with a different Apple ID for 90 days.

So i signed into my other itunes account to download some purchase i had made on that account, went to sign back into my new account and download purchases i had made on my iphone adn it tells me "You can download past purchases on this computer with just one Apple ID every 90 days. You cannot associate this computer with a different Apple ID for 90 days.". This is a shared family computer with multiple Apple IDs being used on it. Not cool apple. This needs to be figured out. Not acceptable for families that have more than one apple ID to have to wait 3 months to download old purchases. Get real. Any way i can 'override' this?

http://support.apple.com/kb/ht4627
http://www.apple.com/feedback/
Contact itunes support. They may grant a one time exception at their discretion.
https://getsupport.apple.com

Can't play my library: "This computer is already associated with an Apple ID...you can download past purchases on this computer with just one Apple ID every 90 days. You cannot associate this computer with a different Apple ID for 88 days." Got a fix?

Since my daughter burned a CD from my computer using our shared libraries I cannot play my library. This pops up: "This computer is already associated with an Apple ID. You can download past purchases on this computer with just one Apple ID every 90 days. You cannot associate this computer with a different Apple ID for 88 days." I can get as far as viewing my library but listening is denied by this pop-up. Can anyone help, please? I just noticed my (this) computer is not showing as registered to my account. Hmmm....a clue perhaps?

Do you have a question?

You can use iTunes Match on this computer with just one Apple ID every 90 days. You cannot associate this computer with a different Apple ID for 5 days.

I only have 1 Apple ID. I turned off iTunes Match on my iMac, and now I cannot turn it back on. I get this error when I try to just turn iTunes Match back on, on the same computer, with the same Apple ID that I used orginially to subscribe to iTunes Match:
This computer is already associated with an Apple ID.
You can use iTunes Match on this computer with just one Apple ID every 90 days. You cannot associate this computer with a different Apple ID for 5 days.
I checked for iTunes updates. None are available since I am using the latest.
I stopped/started iTunes. I rebooted the iMac.
NOTHING HELPS!!!!!!!!
I have a Mac Mini and I use the same Apple ID on iTunes there. I was able to turn iTunes Match off and back on with no trouble at all but my iMac refuses to allow me to turn on iTunes Match.
Now what do I do?

Unless you really only have one AppleID that you use with the iTunes Store there's really nothing you can do. In the case of having only one AppleID you should contact iTunes Store support, since that would be a server-side problem.

HT4913 iTunes Match:You can use iTunes Match on this computer with just one Apple ID every 90 days. You cannot associate this computer with a different Apple ID for 85 days. What can I do?

I'm subscribed to iTunes Match but when I turn it on I get this message:You can use iTunes Match on this computer with just one Apple ID every 90 days. You cannot associate this computer with a different Apple ID for 85 days. What can I do?

I had this happen back in December/January. I sold my MBP that I used to subscribe to iTunes Match back in December. In January, I bought a used MB and tried to use iTunes Match on it. I was told I had to wait nearly two months to use it on the new computer. I waited and was finally able to use it in the new computer.\
Sadly, this has more to do with the content providers (Record lables / movie studios) than it has to do with Apple impsoing the restrictions.

HT201272 You can download past purchases on this computer with just one Apple ID every 90 days. You cannot associate this computer with a different Apple ID for 88 days.

What is going on with my apple ID. I only have one, the iMac is only associated with this ID, yet i get this message after evry thing i try to download from the store......You can download past purchases on this computer with just one Apple ID every 90 days. You cannot associate this computer with a different Apple ID for 88 days.

Hello BW1968,
Thanks for using Apple Support Communities.
For more information on this, take a look at:
iTunes Store: Associating a device or computer to your Apple ID
http://support.apple.com/kb/ht4627
Once a device or computer is associated with your Apple ID, you cannot associate that device or computer with another Apple ID for 90 days.
Best of luck,
Mario

You can download past purchases on this computer with just one Apple ID every 90 days. You cannot associate this computer with a different Apple ID for 60 days. Why?

You can download past purchases on this computer with just one Apple ID every 90 days. You cannot associate this computer with a different Apple ID for 60 days. How can I use more than one apple ID with one MacBook pro ?

Hi
No - that is the issue - both my husband and I use the same computer and want to be able to use our individual Apple IDs so can access our download content e.g. I-books that we have purchased through our other MAC devices such as I-Pad. In the past, we had four people using one computer with no problem regarding Apple ID. In the newer operating system, we are now restricted to one at a time - it means one of us is blocked out from accessing our content for a period of 90 days. Have you any suggestions on how we can both use our individual Apple IDs with the same lap-top? We have set up discrete accounts so we log on to the computer individually. Many thanks for any help.

You can download past purchases on this computer with just one Apple ID every 90 days. You cannot associate this computer with a different Apple ID for 74 days.

You can download past purchases on this computer with just one Apple ID every 90 days. You cannot associate this computer with a different Apple ID for 74 days.
What does that mean ???

Hi
No - that is the issue - both my husband and I use the same computer and want to be able to use our individual Apple IDs so can access our download content e.g. I-books that we have purchased through our other MAC devices such as I-Pad. In the past, we had four people using one computer with no problem regarding Apple ID. In the newer operating system, we are now restricted to one at a time - it means one of us is blocked out from accessing our content for a period of 90 days. Have you any suggestions on how we can both use our individual Apple IDs with the same lap-top? We have set up discrete accounts so we log on to the computer individually. Many thanks for any help.

Interface Dot11Radio0 cannot associate: No Response

Similar Messages

Maybe you are looking for