Interface in shutdown, Link-LED stays on.

I shutted down the GigabitEthernet-I/F on a cisco3845-router. The Link-LED stay on. Shouldn`t the Link-LED went off when the Interface is Administratly down?
The other side off the Cable is connected to a Catalyst. Does anybody have a expaination for this behavior?

Are you using the CLI to issue the command? The reason I ask is I have had instances where issuing the command via a GUI did not acutally apply the command.
This is rather peculiar...

Similar Messages

  • Hp Pavilion 750n just beeps and LEDs stay lit

    My Hp Pavilion was on Saturday and now it just beeps every 2 seconds and the LEDs stay it and it never shuts off. And there is no video to the monitor. Can someone help me????
    This question was solved.
    View Solution.

    If the XP machine is still functional, you can use the Easy Transfer XP to WIN7 or WIN8. In either case, the WIN8 link is a great read, as it covers a tutorial for WIN7 and 8. Easy Transfer Cable for the computers.
    This simple device can be used to copy your folders (documents, picture, music) to another computer.
    The following document, with videos, will assist you in removing the hard drive.
    I am a volunteer. I am not an HP employee.
    To say THANK YOU, press the "thumbs up symbol" to render a KUDO. Please click Accept as Solution, if your problem is solved. You can render both Solution and KUDO.
    The Law of Effect states that positive reinforcement increases the probability of a behavior being repeated. (B.F.Skinner). You toss me KUDO and/or Solution, and I perform better.
    (2) HP DV7t i7 3160QM 2.3Ghz 8GB
    HP m9200t E8400,Win7 Pro 32 bit. 4GB RAM, ASUS 550Ti 2GB, Rosewill 630W. 1T HD SATA 3Gb/s
    Custom Asus P8P67, I7-2600k, 16GB RAM, WIN7 Pro 64bit, EVGA GTX660 2GB, 750W OCZ, 1T HD SATA 6Gb/s
    Custom Asus P8Z77, I7-3770k, 16GB RAM, WIN7 Pro 64bit, EVGA GTX670 2GB, 750W OCZ, 1T HD SATA 6Gb/s
    Both Customs use Rosewill Blackhawk case.
    Printer -- HP OfficeJet Pro 8600 Plus

  • Why does my mouse optical LED stay on (PS/2) when PC off

    I've got the MSI KT4 Ultra (Vanilla)... when I'm using my mouse thru the PS/2 connector and shutoff the PC, the LED stays on... also my router shows that the PC is still connected even tho my PC is off... the other PCs on the network don't have this problem... finally my keyboard NumLock light is on when PC off, which forced me to connect my old keyboard with no light indicators...
    so what I think the problem is, is the wake-on features... all have been disabled in the Bios but is there another setting in the Bios that can stop this small amount of electricity being used on these devices... I'm afraid my LEDs will eventually wear out...
    I could plug my input devices to USB, but I much rather prefer using PS/2 simply cuz the mouse software I use with the mouse works perfectly under these conditions and sets me up as a normal mouse when USB (I've got 5 buttons on the mouse)...
    is there another jumper onboard that can disable these features, or again a Bios setting? or does the newest Bios fix these issues (if u can call them issues)

    ok I may have found a solution but I'm not sure...
    Fri night I decided to switch Ethernet PCI cards... my net was slow and constantly losing connection with router during gaming sessions so I thought this may have fixed it (turned out to be a net issue)... as said previous I switched from my Aopen 325 (has WOL feature) to my old Sohoware Auto PCI (not sure but don't think WOL is on this card - don't have a manual since it came with my cable modem)...
    first let WinXP load default drivers... it loaded the chip drivers as macronix... now I think I distinctly remember shutting off to do some gut working... optical LED was still on (not sure)... did my work and switched PC on and loaded on the Sohoware drivers... PC was on overnight till Sat when I shut it off at night... not paying attention to the LED, I woke up Sun morning with the LED off... very odd since I didn't think putting on proper driver would fix it... woke up today with the same thing... I just shutdown to make sure it wasn't luck and again LED was off...
    originally my Aopen used the Realtek drivers as that is what XP detected... I've used the Aopen drivers with no luck... now it seems as tho it's fixed by simply using an Ethernet with no WOL feature... still I'm not sure if the Sohoware card does or does not support WOL...
    so I'm really out of hardware to test out... if anyone else can further put time into checking this and confirm if this is a WOL Ethernet + MSI KT4 (I've also heard other mobos can have same effect) problem...
    if things change I will post it here again but so far so good...
    [edit]
    sohoware has no mention of WOL feature for my card on their site... yet Aopen has confirmed that their card has WOL feature... I went to Macronix website and they don't have mention of WOL for their chip so I guess Sohoware card dont' support it either... again not sure if LED was off when I shutoff before gutting my PC...

  • RV082 v3 hardware and WAN1 without link(LED)

    Hi,
    We have a RV082 hardware version 2. (I stated wrongly that I had v3 hardware)
    The problem is really stange:
    - doing a hard reset (30, 30, 30 procedure) and after loading the firmware 1.3, the WAN1 o WAN2 link LED does not turn on. In the web admin interface, both port appears disconnected. Connecting the same cable in port 1, it works.
    - then, upgrading to firmware 2.0, in snmp the WAN1 does not show traffice, only the LAN Interface. And the data of the snmp is wrong (reporting million of packets/s), so there is no way to monitor activity.
    My question, is the hardware malfuntioning? If so, why does it works with firmware 2.0 but report bad snmp data? Also, why does not work with firmware 1.3?
    Many thanks
    Oliver
    changed to v2 hardware

    The problem en RV082 with firmware 2.x is that the DNA queries are not resolved from a Mac OSX client.
    Test opening Mac App Store you will see missing icons, reboot to 1.3 firmware and problem solved. I obviously tested many things like factory reset, etc
    Thanks
    Oliver
    Sent from Cisco Technical Support iPhone App

  • Why the network link LED always off for all B200 blade servers? is it normal or heathy?

    Hi Expert,
    Why the network link LED always off for all B200 blade servers? is it normal or heathy? refer to the installation document, it means no active network connection. However, all these servers are up and running with netwirk connection. anyone could explain this?

    Hi Tabish,
    How many times do you have to open this same topic?
    In my opinion, this is your THIRD thread for the same topic.

  • FP2015 status led stay lit

    While turning on the system the status led stay on. Doing this few time, now the Status led doesn’t stay on but it seems that the controller doesn’t make the booting procedure (the Leds doesn’t turn on and off at the begging)

    This issue can generally be solved by formatting the internal Compact FLASH memory on the controller. There is a < a href="http://digital.ni.com/public.nsf/websearch/6​D0F9F74FD2DAD0186256EE5007198D4?OpenDocument">Know​ledge Base that describes in detail how to format the controller. Sometimes you will first have to switch both the Safe Mode (switch 7) and Reset IP (switch 8) dip switches and cycle the power to first get the controller into a safe state.
    The Compact FLASH corruption is generally due to losing power while writing to a sector on disk. This can cause that sector as well as other adjacent sectors to become corrupt.

  • Dot11 interface is shutdown

    Hi,
    My 3502i suddently shutdown it's Radio interface and when I connect to it, I cans ee that the interface is shutdown. So tryign to enable it but the "configure terminal" command is not available. Is there any hidden command to go the priveledge mode?
    interface Dot11Radio0
    no ip route-cache
    shutdown
    antenna gain 0
    beamform ofdm
    mbssid
    speed  basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0 m5-2 m6-2 m7-2 m11-2 m12-2 m13-2 m14-2 m15-2
    power local -1
    power client local
    packet retries 64 drop-packet
    no cdp enable
    interface Dot11Radio1
    no ip route-cache
    shutdown
    antenna gain 0
    beamform ofdm
    mbssid
    Cisco IOS Software, C3500 Software (AP3G1-K9W8-M), Version 12.4(25e)JA, RELEASE SOFTWARE (fc2)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2012 by Cisco Systems, Inc.
    Compiled Fri 27-Jan-12 21:51 by prod_rel_team
    ROM: Bootstrap program is C3500 boot loader
    BOOTLDR: C3500 Boot Loader (AP3G1-BOOT-M) Version 12.4(23c)JA5, RELEASE SOFTWARE (fc1)
    thanks

    Hi,
    Not the interface but the radio interface on this AP so I just replace it with a new one (good thing we have a spare).
    *Dec 16 23:26:42.159: %SYS-3-CPUHOG: Task is running for (11010)msecs, more than (2000)msecs (0/0),process = Dot11 driver.
    -Traceback= 0x3A8328 0x3A3318 0x58C268 0x58C1A4 0x58D408 0x58D93C 0x58D9CC 0x5F7178 0x59D550 0x5AA238 0x2A20D0
    *Dec 16 23:26:43.732: %SYS-3-CPUHOG: Task is running for (12583)msecs, more than (2000)msecs (0/0),process = Dot11 driver.
    -Traceback= 0x3A8340 0x3A8324 0x58C268 0x58C1A4 0x58D408 0x58D93C 0x58D9CC 0x5F7178 0x59D550 0x5AA238 0x2A20D0
    *Dec 16 23:26:44.270: %SYS-3-CPUYLD: Task ran for (13120)msecs, more than (2000)msecs (0/0),process = Dot11 driver
    *Dec 16 23:26:44.273: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Dec 16 23:26:44.289: %CLEANAIR-6-STATE: Slot 0 down
    *Dec 16 23:26:44.930: ERROR: wait 3 failed
    *Dec 16 23:26:44.930: Radio reset failed: wait 3
    *Dec 16 23:26:44.930: PCIe reset radio 0, bus 1
    *Dec 16 23:26:45.037: PCIEx: Initialization count 0 ERROR port [0] bad vc0=0
    Then the radio are now gone after the reboot/reset;
    *Dec 17 03:26:45.037.786: the Slot 0 has no radio
    *Dec 17 03:26:45.037.786: the Slot 1 has no radio
    So check via console, seems like a hardware issue.
    Rgds

  • Interface Controller and Link to URL

    Hi Experts,
    Could some give me the step by step process(PDF's suggested) for the Interface controller and Link to URL.
    Regards.

    hi,
    The application of downloading data from table to excel sheet
    will give a very good idea and the solution to ur problm
    Exporting Context Data into Excel Using the Web Dynpro
    Binary Cache
    https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/edc2f3c2-0401-0010-8898-acd5b6a94353
    Regards
    Nikhil Tapkir

  • Network link LED on UCS blades

    Hi,
    we got a working UCS system (6248 FI , 5108 chassis with 2204 IOM and B200-M3 blades) all is working fine but the network link LED are off. Is this a normal behaviour ? Since according to documentation they should blink green.
    regards

    Hi Lukasz,
    I'm assuming we are speaking about the network LED 's on the IOM which are off.
    What about the LED's on the respective ports on the FI?
    What's the color of the LED's on the power supplies?
    Thanks,
    Majid

  • After installing Firefox 6, when I click on an e-mail (thunderbird) link, Firefox stays on the backround and does not open in front. How can I make firefox come to the front automatically when a link is clicked?

    If I receive an e-mail on thurnderbird with a link to a URL, if I click it firefox will open in the background, but it won't automatically com to the front, but will stay in the back. I have to click on the thurnderbird icon to make the firefox screen come up.

    See this lnk for a fix, it worked for me!
    http://www.pcworld.com/article/200103/fix_outlook_general_failure_error_for_email_links.html

  • Front LED stays on when in closed lid operation

    Is the front led supposed to stay on? my previous powerbook didn't do this, but this may be a new intel feature, maybe?

    I have the same question. Also, when I unplug an external Monitor when my macbook is closed, I notice the backlight keys look like they were on the whole time. That doesn't seem good, although I suppose it won't really hurt anything.

  • CFP status led - stays lit solid red!

    Hi,
    I have a problem with a cFP-2120 RT controller where the red LED status light stays lit.  On the instruction manual it says that the unit was not powered up correctly and to contact NI.  The controller used to work fine until we had a short on the mains side of the power supply The AI, AO and thermocouple modules did not power up but the DI and DO modules seemed to be getting power.  Is there anything we can do or just send it back for repairs.  When I replaced the controller with another one, the system worked fine and the status LED turned off after a few seconds.
    rgds
    Inzaghi_2

    Sounds like you've proven that the controller is bad.  Next step is an RMA from NI.  Make sure NI tells you what failed in the controller and see if they will comment on what might have caused it.   The idea being to see if you can do anything to prevent this failure in the future.

  • ASUS P6X58D Memory OK (MEMOK!) issue  DRAM LED Stays solid red.

    HI
    This morning when I turned on my computer, it would not boot. Not even the most basic boot (I could not get to the ASUS bio DOS screen, for example).   It would only sound  one beep, and then finally a second beep-- but the second beep did not sound immediately thereafter. .  Usually, I recall, I hear two rapid beeps almost immediatley when I boot up.
    I did some checking on the net.  It appears to be a memory issue. I reset my memory in their slots. But that did not help.
    I saw the on the ASUS motherboard the DRAM LED light was solid red.  After checking the manual (and checking some YouTube videos), I pressed the MEMOK! button right next to the DRAM LED light.  
    According to the manual, when using WIndows OS  the system will reboot as it does its "Flashing lights" test to try to use a memory failsafe setting.  However, even after reboot the red light stayed solid and appeared not to do the testing.
    Perhaps I am not doing the test correctly.  For example, do I keep my finger on the MEMOK! button throughout the tests and reboots??  Or just press once, and never press it again.
    ASUS USA support appears to be closed today for the New Year's holiday.  So I am wondering if anyone here has some suggestions.  My memory was working fine up until this morning.
    I suppose I could wait until tomorrow when ASUS phone support is live again, but thought someone might have some suggestions / tests I can do today.
    Thanks
    Rowby

    Well I fixed it.
    Not sure exactly what I did that fixed it, but here is what I did.
    1)  I unplugged the computer. 
    2)  I disconnected the power supply from the motherboard.
    3)  I removed the battery.
    4)  I let it sit for about an hour.
    5)  I pushed the motherboard reset button on the back of my computer (I perhaps should have done this first, but I did it.)
    6)  I put a new battery into the motherboard (perhaps the old one was dead or a zombie.)
    7)  I reconnected the power supply to the mother board.
    8)  I plugged in the box.
    9)  I heard the familiar two beeps, and sure enough the unit booted up. 
    Upon bootup the ASUS screen had me to into bios and double check everything.   Then it all rebooted again, and opened windows 7.
    I will make sure I have the lastest ASUS bios.  But I see that it is recognizing all 24 GB of memory, so I guess I am good to go.
    Rowby

  • Satellite P300 156 PSPC4E - White Media LEDs stay on after power-off

    HI
    I have a Toshiba Notebook Satellite P Series P300 156 (PSPC4E) which has just developed a problem
    When I power off, the laptop shuts down normally and power button itself goes off, but the 6 white media LED's to the right of the power button remain on constantly. The only way to get these to turn themselves off is to disconnect the battery.
    Can anyone please advise
    Many thanks

    Thanks for the replies
    I tried altering the BOIS, but that only affects the illuminated strip along the top of the mouse touch pad.
    I cant remember which version of BIOS that I got (I'm at work at the moment) but I tried downloading the latest from here (dated 18/03/10), and it made no difference.
    Its a strange one. The lights stay on even if the laptop is closed for long periods. They just never go off, unless I take the battery out.
    Message was edited by: hawkerpaul

  • Macbook shutdown hanging - dock stays open

    Hey, my first post (excuse the username, I made this account years ago...).
    I've had a problem shutting down my new MBP Retina 13'' recently. Often (not every time however), when I go to shutdown the computer (Apple > Shut down > shut down), the computer appears to be shutting down normally (the menu bar and desktop icons disappear), but then the dock stays open, and does not shut down. I've waited and waited but it doesn't shut down. To get it to finally shut down, each time this happens, I have to hold the shutdown button and select shutdown again, and then after a few seconds shutdown occurs normally.
    I spoke to Applecare on the phone, they told me to perform a safe boot and then it should be okay, and it was for a while until it started again. I went into an Apple Store today, and they said it's 99% likely that it's just something like an app or process causing it to hang. The guy suggested to toggle my login items on and off and see if that fixes it, which it didn't (I only have 2, Dropbox and Caffeine).
    Can anyone relate or have any ways to fix this? It's not that bad, but just annoying enough to bother me. Thanks!

    Reset SMC.     http://support.apple.com/kb/HT3964
    Choose the method for:
    "Resetting SMC on portables with a battery you should not remove on your own".
    Start up in Safe Mode.  http://support.apple.com/en-us/HT1564
    Best.

Maybe you are looking for