Interface status on Cisco CAt 4500 switch as source-monitoring

Hi Guys,
I have assigned int gi3/45 on my Cisco 4500 CAT switch as the monitoring port as source and gi3/47 as the destination.
I see this:
GigabitEthernet3/45 is up, line protocol is down (monitoring)
but on the destination port both are up, interface up and line protocol up.
is this natural? I have executed the no shutdown on gi3/45 but it still says down!
is this normal? or there is a problem? i have monitoring on my edge switch CAT 3560 but both are saying UP/UP, shouldn't this be the same since both swithces are running Cisco IOS.
Please respond. I appreciate your input and thanks in advance.
Masood

this interface (g 3/45) is the destination, it says so "monitoring", it normal for the "destination" or "monitoring" port to be up/down coz it's not sending or receiving traffic destined to it, only the mirrored packets from the source port. can you post the "show monitor session #"?

Similar Messages

CS6/CC - switching between source monitor and timeline disaster

Now what is this?
It all works fine until you try DV Output.
In DV Output mode every time you switch between source monitor and the timeline it goes to some scary ritual:
1. output disabled on external monitor
2. some crazy flickering happens
3. ok, now updated picture on external monitor finally appears
Same happens when switching back to timeline.
Also when scrubbing through timeline video and audio is late for a few centuries on DV device/external monitor/speaker.
Why Adobe screwed firewire environment editing? I'm thinking about changing my job. Editing with Premiere is killing me lately. I'm thinking about starting to work with bees or strawberries, or something else less frustrating.
And Premiere CS 5.5 was the best editing software ever released. It has no similar problems. Why CS6 and CC are retarded?

I'm just asking for properly working feature which is alredy implemented and worked fine in earlier versions.
Adobe, can this be fixed, please?

STP LED status with Cisco Catalyst Blade Switch 3130

Hi,
The usual status LED of a STP Blocked interface is orange. With this Switch (3130), the LED is green while the RSTP status port is Alternate Blocked. Is this normal ? Is there any documentation about RSTP LED status ?

G'day,
I think you have the wrong forum! :)
cheers

Glitch in Audio when switching from Source Monitor to timeine in PPro

I am running a nMP 3ghz 8-core, 16gb ram, D700's, on osx 10.10. PProCC is 8.2.0 (65) Build. It is the most up to date version on CC. I also have a Focusrite Scarlette 2i2 for my Audio interface. This is where I'm having the issue. When I playback a clip in the source monitor, then go to play something in the timeline I get a weird 2 second delay with 2 pop's in my speakers, the lights on the XLR gain knobs on the focusrite audio interface flash twice in sync with the audio pops, then the timeline will play. And if I now go to play something in the source monitor coming from the timeline it does the same thing, 2 seconds, pops, lights then it plays. But if I stop and start the clip in either the source monitor or timeline without switching between, it plays fine. Only switching between the source monitor and the timeline. I have tried numerous things in the ASIO settings but nothing seems to get rid of this glitch and it drives me and my clients insane because it does it every single time I switch between the two. HELP!

Cam, I have this exact same problem. I plan on sending out some emails to hopefully find a solution, but I thought I would check here quick. Did you ever find an answer to your question elsewhere?

Cisco Cat 500 Express deficiency

I have heared complaints about the Cisco Cat 500 switch.
When using the Cat 500 with AP1200 and 7920 IP phones, the phones do not roam from AP to AP.
Also I have found out that the Cat 500 will not relay dhcp request to a server on a seperate vlan from it's configured ip address.
With CLI switches, the "ip helper-address under the vlan will acheive this. With the Cat 500, how do u acheive directed broadcast.
Looks like this switch is not very good. The smartports do not work very well, you will find that choosing "other" as a smartport fixes most connectivity issues.
Cisco your comments?

The Cat 500 Express is a Layer 2 switch - like the older model switches, it has a single SVI which is in one VLAN.
If you have more than one VLAN, then you will probably have a device that routes between them (this won't be a Cat 500 - it would be a Cat 3xxx layer three switch or a router most likely) and this device would be what provides Ip-helper functionality...
Regards
Aaron
Please rate helpful posts...

OSPF in IP Base License (Cisco 4500 switch)

Hi,
Can someone explain what is the purpose or meaning of "OSPF for Routed Access" in IP Base license for 4500 switch? I'll be installing 4500 switch for my distribution, and 6500 switch for my core. These two switches will use OSPF as their routing protocol. The 6500 comes with an IP Service license, while 4500 comes with IP Base license only. I am worried if I will have a problem implementing OSPF between the two since IP base states it has "OSPF for roued access", while IP services supports OSPFv2 and v3.
Please help...
thanks,
shawn

Shawn
OSPF for routed access is designed to allow you to extend L3 to your access layer. It supports one instance of OSPF and up to 200 routes. That said i have come across a thread on here where a person reports having many more routes so i'm not sure it is a hardwired limit but i would try and stay within that.
See this link for details -
http://www.cisco.com/c/en/us/products/collateral/switches/catalyst-4500-series-switches/product_bulletin_c25-553133.html
Edit - i should say i have not use it myself but from the document it seems pretty clear it is simply a normal OSPF setup but limited to how many routes you can have.
Jon

Including Interface Description in Cisco PRime Infrastructure Alarm Message

Hi all,
i succesfully configured a Cisco Prime Infrastructure 2.1 applliance to display an alarm and to send me an e-mail when switch uplink ports goes down.
The text displayed in alarm message is :
port 'interface_id' is down on device 'device_ip_address'
I'd like to include in this text also the interface description so the text will display :
port 'interface_id' 'interface_descriprion' is down on device 'device_ip_address'
Is this possible?
Thankyou in advance

Hi,
i followed these steps :
SWITCH SIDE
- configured Prime Infrastructure as snmp-server host;
- enabled snmp-traps for linkup and linkdown events globally;
- disabled snmp-traps for linkup and linkdown on non relevant interfaces using the no snmp trap link-status command
PRIME INFRASTRUCTURE SIDE
- under "Deploy/Monitor Deployment" i deployed template "Interface Health" for all the interested switches
- under "Administration/System Settings/Mail Server Configuration" configured my internal SMTP server to make Prime Infrastructure able to send e-mails
- under "Operate/Alarms & Events" click on "Email Notifications" , then on "Switches and Hubs"
- check the "critical" box , insert the destination e-mail address into the "To" field then click "Save"
- check the "switches and Hubs" box and then click Save
As i know is possible to avoid to configure every single not-interesting port on the switches with "no snmp trap link-status" command (it's a bit annoying when you have tens of switches), using Port Grouping configuration on PI but i tried it without success.
Hope this helps.
Best Regards,

Sh Interface status

Hi! What's the command for sh interface status in CAT OS?
Thks!

Hi Friend,
You will not get the exact output as you get is IOS but you can take the output from this commands
sh port
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat6000/sw_8_5/cmd_ref/sh_p_sn.htm#wp1715472
sh mac
Have a look at this for details on "sh mac" command
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat6000/sw_8_5/cmd_ref/sh_ml_n.htm#wp1028548
HTH, if yes please rate the post.
Ankur

AP 1252 dot11radio interface status shows RESET

Hi,
This is regarding an issue with one of my access point. The access point 1252 is autonomous one running the IOS version
C1250 Software (C1250-K9W7-M), Version 12.4(10b)JDA3, RELEASE SOFTWARE (fc1)
The status of the dot11Radio 0 interface is showing as RESET. I have pasted the interface brief details below.
ap03#
ap03#
ap03#sh ip int brief
Interface                  IP-Address      OK? Method Status                Protocol
BVI1                       <ipaddress>       YES DHCP   up                    up
Dot11Radio0                unassigned      YES TFTP   reset                 down
Dot11Radio0.102            unassigned      YES unset reset                 down
Dot11Radio0.104            unassigned      YES unset reset                 down
Dot11Radio0.105            unassigned      YES unset reset                 down
Dot11Radio0.108            unassigned      YES unset reset                 down
Dot11Radio1                unassigned      YES TFTP   administratively down down
GigabitEthernet0           unassigned      YES TFTP   up                    up
GigabitEthernet0.102       unassigned      YES unset up                    up
GigabitEthernet0.104       unassigned      YES unset up                    up
GigabitEthernet0.105       unassigned      YES unset up                    up
GigabitEthernet0.106       unassigned      YES unset up                    up
GigabitEthernet0.108       unassigned      YES unset up                    up
ap03#
Due to this the clientsa re not getting associated.
I tried rebooting the AP; shut the dot11radio0 interface and unshut it; verified the switch end duplex speed settings. Looks good.
Can anyone suggest me how to proceed?
Thankyou.

Hi,
Yes the Access Point was working fine all these days and for the last one week, I am facing this problem. Please find the running configuration of the Access point as below..
Building configuration...
Current configuration : 8275 bytes
version 12.4
no service pad
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
hostname ap03
logging buffered 65536 notifications
enable secret 5 $1$.WG7$dvJpY1XHuixBk3wA4sfR3/
aaa new-model
aaa group server radius rad_eap
server auth-port 1812 acct-port 1813
aaa authentication login default group tacacs+ local enable
aaa authentication login eap_methods group rad_eap
aaa authorization exec default group tacacs+ local
aaa accounting exec default start-stop group tacacs+
aaa session-id common
clock timezone MST -7
clock summer-time MDT recurring
ip rcmd rsh-enable
ip rcmd remote-host datacom datacom enable
ip rcmd remote-host datacom datacom enable
ip rcmd remote-host datacom datacom enable
ip rcmd remote-host datacom datacom enable
ip rcmd remote-host datacom datacom enable
ip rcmd remote-host datacom datacom enable
ip rcmd remote-host datacom datacom enable
ip rcmd remote-host ncc ncc
ip rcmd remote-host ncc ncc
ip rcmd remote-host ncc ncc
ip rcmd remote-host ncc ncc
ip rcmd remote-host ncc ncc
ip rcmd remote-host ncc ncc
ip rcmd remote-host ncc ncc
ip rcmd remote-host datacom datacom enable
ip rcmd remote-host datacom datacom enable
ip rcmd remote-host datacom datacom enable
ip rcmd remote-host netsvcs netsvcs enable
ip rcmd remote-host netsvcs netsvcs enable
ip rcmd remote-host netsvcs netsvcs enable
ip rcmd remote-host netsvcs netsvcs enable
ip rcmd remote-host netsvcs netsvcs enable
ip rcmd remote-host netsvcs netsvcs enable
ip rcmd remote-host netsvcs netsvcs enable
ip rcmd remote-host netsvcs netsvcs enable
ip rcmd remote-host netsvcs netsvcs enable
ip rcmd remote-host datacom datacom enable
ip domain list u04129.albertsons.com
ip domain list albertsons.com
ip domain name u04129.albertsons.com
ip name-server
ip ssh time-out 90
dot11 activity-timeout unknown default 28800
dot11 ssid Courage-34idkeysNCswuZue3765#%@&
   vlan 102
   authentication open eap eap_methods
   authentication key-management wpa
dot11 ssid Freedom-jKb%&552en@546AsdfG65eD
   vlan 105
   authentication open eap eap_methods
   authentication network-eap eap_methods
   authentication key-management wpa
dot11 ssid Galaxy-73j4CA58fd66y3lKICK#%@&*
   vlan 104
   authentication open
dot11 ssid Quake-35f8d4q9e5@365%lFh&ju#ef2
   vlan 108
   authentication open eap eap_methods
   authentication key-management wpa
dot11 holdoff-time 60
dot11 arp-cache optional
power inline negotiation prestandard source
dot1x timeout reauth-period server
username Cisco password 7 02250D480809
username ggg privilege 15 secret 5 $1$E4Ms$78SOM7s3gZ8QxU.mlnEpj.
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 104 key 1 size 128bit 7 80B78765DD670039FE1557E4BFB4 transmit-key
encryption vlan 104 mode wep mandatory
encryption vlan 108 mode ciphers tkip
encryption vlan 102 mode ciphers tkip
encryption vlan 105 mode ciphers tkip
ssid Courage-34idkeysNCswuZue3765#%@&
ssid Freedom-jKb%&552en@546AsdfG65eD
ssid Galaxy-73j4CA58fd66y3lKICK#%@&*
ssid Quake-35f8d4q9e5@365%lFh&ju#ef2
power local 17
packet retries 64 drop-packet
no preamble-short
channel 2412
station-role root
beacon dtim-period 4
no dot11 extension aironet
bridge-group 1
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0.102
encapsulation dot1Q 102
no ip route-cache
no cdp enable
bridge-group 102
bridge-group 102 subscriber-loop-control
bridge-group 102 input-type-list 201
bridge-group 102 output-type-list 201
bridge-group 102 port-protected
bridge-group 102 block-unknown-source
no bridge-group 102 source-learning
no bridge-group 102 unicast-flooding
bridge-group 102 spanning-disabled
interface Dot11Radio0.104
encapsulation dot1Q 104
no ip route-cache
no cdp enable
bridge-group 104
bridge-group 104 subscriber-loop-control
bridge-group 104 input-type-list 201
bridge-group 104 output-type-list 201
bridge-group 104 port-protected
bridge-group 104 block-unknown-source
no bridge-group 104 source-learning
no bridge-group 104 unicast-flooding
bridge-group 104 spanning-disabled
interface Dot11Radio0.105
encapsulation dot1Q 105
no ip route-cache
no cdp enable
bridge-group 105
bridge-group 105 subscriber-loop-control
bridge-group 105 input-type-list 201
bridge-group 105 output-type-list 201
bridge-group 105 port-protected
bridge-group 105 block-unknown-source
no bridge-group 105 source-learning
no bridge-group 105 unicast-flooding
bridge-group 105 spanning-disabled
interface Dot11Radio0.108
encapsulation dot1Q 108
no ip route-cache
no cdp enable
bridge-group 108
bridge-group 108 subscriber-loop-control
bridge-group 108 input-type-list 201
bridge-group 108 output-type-list 201
bridge-group 108 port-protected
bridge-group 108 block-unknown-source
no bridge-group 108 source-learning
no bridge-group 108 unicast-flooding
bridge-group 108 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
shutdown
dfs band 3 block
channel dfs
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
interface GigabitEthernet0.102
encapsulation dot1Q 102
no ip route-cache
bridge-group 102
no bridge-group 102 source-learning
bridge-group 102 spanning-disabled
interface GigabitEthernet0.104
encapsulation dot1Q 104
no ip route-cache
bridge-group 104
no bridge-group 104 source-learning
bridge-group 104 spanning-disabled
interface GigabitEthernet0.105
encapsulation dot1Q 105
no ip route-cache
no cdp enable
bridge-group 105
no bridge-group 105 source-learning
bridge-group 105 spanning-disabled
interface GigabitEthernet0.106
encapsulation dot1Q 106 native
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface GigabitEthernet0.108
encapsulation dot1Q 108
no ip route-cache
no cdp enable
bridge-group 108
no bridge-group 108 source-learning
bridge-group 108 spanning-disabled
interface BVI1
ip address dhcp client-id GigabitEthernet0
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
ip radius source-interface BVI1
no logging trap
access-list 1421 permit
access-list 1421 permit
access-list 1421 permit 0.0.0.255
access-list 1421 permit 0.0.0.255
access-list 1421 permit 0.0.255.255
access-list 1421 permit 0.0.255.255
access-list 1421 permit 0.0.255.255
access-list 1421 permit 0.0.255.255
access-list 1421 deny   any
access-list 201 permit 0x0800 0x0000
access-list 201 permit 0x0806 0x0000
access-list 201 deny   0x0000 0xFFFF
snmp-server view NCC mib-2 included
snmp-server community TROUbleIStrouBLE view NCC RO
snmp-server community CHECKtheMAIL RO
snmp-server community HAVocREEk RW
snmp-server community 1aPe3nLnmDt4yVYmbgWoUVjJYz1 view NCC RO 1421
snmp-server community 1aUQ5DAIH2bTBlvJg6RFS5qfsr RO 1421
snmp-server community 1OGgsN21DI4q01QeeIhJGF961 RW 1421
snmp-server enable traps tty
tacacs-server host
tacacs-server host
tacacs-server directed-request
tacacs-server key 7 110A1D5347415C5B53737F7D2E26
radius-server attribute 32 include-in-access-req format %h
radius-server host auth-port 1812 acct-port 1813 key 7 10190C4A533C07185D50721569013D3C3638022F4E0E42400102773D0D481A5E0E
radius-server vsa send accounting
bridge 1 route ip
line con 0
line vty 5 15
sntp server
end

Show interface status (IOS layer 2switch)

Is it possible to modify the width of the column containing the description of the interfaces when I issue the "show interface status?" on IOS cisco switches?

I don't believe so but you can type show interface description if you want to see the entire description that is associated to the port.
HTH,
Edison.

LAG configuration issue on Cisco SG300 52 Switch

Hi everybody,
I am having an issue with LAG configuration on a Cisco SG300 52 switch. I have connected four Ge ports on the switch to the four NICs of a Dell R710 Server on which I installed Windows Server 2008 R2. Without LAG configured, these ports would forward traffic to and from the Dell server fine. However, if I configure LAG on the ports with LACP enabled, then they would not forward any network traffic. Debugging shows that the ports are up but their forwarding status show N/A. Am I missing any configuration? Can I configure LAG on edgeports? Or is there any compatibility issue?
Any help from you guys will be greatly appreciated.
Thank you.
Vishal

Hi Dave,
Thank you for your quick response and sorry to have looked at it late. Well, I already resolved the issue and like you pointed out, it was the configuration of the Dell NICs. I had to configure NIC teaming and there was a bug with the Broadcom NIC management software. I had to download this piece of software again and I was then able to configure NIC teaming on it. I initially thought that it was already configured because we got the Dell server "pre-installed with pretty much everything".
Anyway thank you for your assistance. Oh I have a question though if you don't mind clearing my doubt. We have bought 7 of these SG300 Switches and I would like to use all of them
in a hierarchical design as core, distribution and access layer switches because I believe this switch has got all the qualities to be used at all the three layers. We have about 100 users in our company at the moment but expecting growth of about 10-20 employees per year. Would you think a hierarchical network design for a 100 users is a bit of an overkill? Would you think these SG300 switches can handle network traffic at the distribution and core layers? I worked out the average daily traffic is only about 4 Mbps.
Thank you for your valuable guidance.
Kind regards,
Vishal
Date: Mon, 12 Sep 2011 08:09:40 -0600
From: [email protected]
To: [email protected]
Subject: - Re: LAG configuration issue on Cisco SG300 52 Switch
Cisco Support Community
Re: LAG configuration issue on Cisco SG300 52 Switch created by David Hornstein in Small Business Switches - View the full discussion
Hi Chundunsing,
Thank you for the purchase of my switch.
Chundunsing, I love the way you worded your question ; "I am having an issue with LAG configuration on a Cisco SG300 52 switch." ,but seriously you are having a problem with interfacing the dell with my switch.
You have LAG working to the Dell R710 teamed NICs and god knows what NICs or drivers you are using to acheive this.
Now LAG is providing , load balancing between the LAG ports.
Now LAG is providing , link redundancy for connectibity to the Dell R710.
If there is a configuration issue , it sure seems the way you have it configured without LACP is still working. But you have the option when you create a LAP group to enable LACP. You can see this as a tick box in the LAG group.
But might i also install, recently firmware version 1.1.1.8, just came out.
Please be sure to;
Step 1. update the firmware on the switch and
Step 2. select it as the 'active image.'
Step 3 rebbot the switch to utilize this active image.
If you are having any trouble doing this the admin guide references how to achieve this. for your concenience I have atteched the guide to this posting.
regards Dave
Reply to this message by going to Cisco Support Community
Start a new discussion in Small Business Switches at Cisco Support Community

4500 switch Reflexive ACL

hello,
I need to apply an Reflexive ACL on switch 4500.
I looking for IOS of 4500 switch that support in Reflexive ACL, and I dont found..
There is an IOS of 4500 that support Reflexive ACL?
What is?
thanks...

Hi,
http://www.cisco.com/en/US/products/ps6350/products_configuration_guide_chapter09186a00804fde65.html.
configure your reflexive access-list on the inside interface and on the external interface configure your normal access-lists to allow access from internet to dmz
regards
John

Gigabit interface status faulty please help

When I do a show interface status on 4500 switch I got a status faulty
I did never see such thing
Port- Name-Status-Vlan-Duplex-Speed Type
Gi2/7-jsh3 faulty 188 full XXBaseSX
Could you please help?
Thanks a lot

this usually indicates the port is faulty (bad; not working; will not work)
this may have been set via the POST of the device. the internal tests failed and the port was marked FAULTY.
this could also be the result of a good port simply went bad for some unknown reason.
try to disable/reEnable the port. will probably still say faulty. (cannot initialize a faulty port)
try to reset the blade the port is on, or the supervisor if it resides on that.
do a "show test" (catOS) to see what the POST found when it did its powerOnSelfTests.
i've seen plenty of FAULTY ports and 99% of the time, the port is simply bad and must be replaced. (usually an ASIC or the likes)

Power Redundancy problem for cisco 3750 stack switches

Hi Team,
I have installed and configured cisco 3750X series switches in stackwise. Those are having dual power supply.
Power redundancy test performed:
1. Removed one of the power supply and inserted it back.
2. once the first power supply is ready, removed another power supply and switch got rebooted.
please find the below stack-power output:
JP2-RDC-DIS-02#sh stack-power detail
Power Stack           Stack   Stack    Total   Rsvd    Alloc   Unused Num Num
Name                  Mode    Topolgy Pwr(W) Pwr(W) Pwr(W) Pwr(W) SW   PS
Powerstack-2          SP-PS   Stndaln 700     477     223     0       1    2
Powerstack-1          SP-PS   Stndaln 700     477     223     0       1    2
Power stack name: Powerstack-2
    Stack mode: Power sharing
    Stack topology: Standalone
    Switch 2:
        Power budget: 223
        Power allocated: 223
        Low port priority value: 22
        High port priority value: 13
        Switch priority value: 4
        Port 1 status: Not connected
        Port 2 status: Not connected
        Neighbor on port 1: 0000.0000.0000
        Neighbor on port 2: 0000.0000.0000
Power stack name: Powerstack-1
    Stack mode: Power sharing
    Stack topology: Standalone
    Switch 1:
        Power budget: 223
        Power allocated: 223
        Low port priority value: 22
        High port priority value: 13
        Switch priority value: 4
        Port 1 status: Not connected
        Port 2 status: Not connected
        Neighbor on port 1: 0000.0000.0000
        Neighbor on port 2: 0000.0000.0000
Can anyone help what went wrong here?
Thanks
Manish

Cosmetic bug
CSCui21029    3750X Stack no standalone stays in running configureation as standalone
Symptom:
When you are configuring a 3750x stack and initially putting it into a stack ring topology by configuring the following.
Switch(config)#stack-power switch 1
Switch(config-switch-stackpower)#sta
Switch(config-switch-stackpower)#no stan
Switch(config-switch-stackpower)#no standalone
You will see that in the running configuration it shows up as standalone mode
stack-power switch 1
switch mode: standalone
stack-power switch 2
switch mode: standalone
Conditions:
3750X stacks with any license level
Workaround:
none

Who is anybody using a WISM with FWSM on a CAT 6500 Switch?

Hi
Who is anybody using a WISM with FWSM on CAT 6500 switch ?
Are there any problem,if use?
And How can I set them to connecting each other ?
I have founded a document relate it on the cisco website that name is Integrating Cisco WiSM and Firewall Service Module.
I have a question concern it.
Why do I have make a VRF to communication each other ?
Please let me know.

As far as the FWSM is concerned you can have each of the wireless vlans come in to the same context of the FWSM and then just add those vlans to the FWSM as separate vlans.

Interface status on Cisco CAt 4500 switch as source-monitoring

Similar Messages

Maybe you are looking for