Interface trip stop error

hi all,
I got interface trip stop error when I do the ship confirm process in sales order.
Thanks&regards
ravi

Hi there,
This forum is for Oracle OLAP users - what does your question relate to?
Thanks
Stuart

Similar Messages

  • Internal Order: Interface trip stop: ERROR: unknown status = ''

    Hello,
    I have completed the setups for Internal orders:(the two orgs are within the same Operating unit, transfer method: direct)
    I am able to
    1. Create internal requisition
    2. Import Order
    3. Book, Pick Release and Submit ship confirm
    Now, the interface trip stop ( the inventory interface part) The status changes to shipped in Shipping transactions.
    The log file does not have an explicit error message. Posting truncated error message below. In more than one place, the following
    vague error messages appear.
    ERROR: unknown status = ''
    X_MASTER_STATUS ==> ERROR
    "Calling program unit WSH_DSNO.SUBMIT_TRIP_STOP
    Entering WSH_DSNO.SUBMIT_TRIP_STOP () (09/27/2006 09:11:09 PM)
    P_TRIP_STOP_ID ==> 4677
    PROCESSING DSNO IN TRIP STOP 4677
    RLM INSTALLED: YES
    Calling program unit RLM_TPA_SV.UPDATECUMKEY
    CHECKING EDI INSTALLATION STATUS
    EDI INSTALLED: YES
    DSNO PROFILE: ENABLED
    No Eligible Delivery for the DSNO
    Terminating program
    INTERFACETRIPSTOP: RESULT OF DSNO SUBMISSION FOR STOP_ID 4677 =
    Entering WSH_SHIP_CONFIRM_ACTIONS.UPDATE_COMPLETION_STATUS (WSHDDSHB.pls 115.310.11510.3) (09/27/2006 09:11:10 PM)
    p_num_stops ==> 1
    p_batch_id ==> is NULL
    X_MASTER_STATUS ==> NORMAL
    P_API_STATUS ==>
    X_NORMAL_COUNT ==> 0
    X_WARNING_COUNT ==> 0
    X_INTERFACED_COUNT ==> 0
    ERROR: unknown status = ''
    X_MASTER_STATUS ==> ERROR
    P_API_STATUS ==>
    X_NORMAL_COUNT ==> 0
    X_WARNING_COUNT ==> 0
    X_INTERFACED_COUNT ==> 0
    Exiting WSH_SHIP_CONFIRM_ACTIONS.UPDATE_COMPLETION_STATUS (09/27/2006 09:11:10 PM, .01 seconds)
    l_api_completion_status ==> INTERFACED
    l_previous_interface ==> TRUE
    Your help is greatly appreciated.
    Thank You,
    Somnath Subramanyam

    Hi somnath,
    U have enabled the DSNO (departure Ship notice outbound) in the profile option
    ECE_DSNO_ENABLED = yes. (through your log file)
    You go to e-commerce gateway responsibility --> go to setup --> profile option --> query this profile option and Change to no and then try again.
    Regards,
    Prasad

  • Interface Trip Stop Run - Log file showing an Error

    Hi
    When I run Interface Trip Stop Run - SRS, Request completed successfully but it has the following error. " Failed GMI_Shipping_Util.GMI.UPDATE_SHIPMENT_TXN for Delivery Id 38237"
    In Sales Order the Line Status is Closed.
    In Shipping Transactions Form the Status is Showing Shipped.Next Step it Run Interfaces.
    When I checked the Lot Qty in Lot Genealogy the on hand qty of that lot is Zero.
    And the transaction is showing Pending in Item Transaction Inquiry.
    Please tell me how to proceed with this sales order.
    Thanks in Advance
    Prem.

    Its a concurrent program.
    Submit a request with name: Interface Trip Stop - SRS.
    i have tested and this will resolve your query too.

  • Interface trip stop  -- Completed with Warining in inventory where do you

    Hi Guru's
    While running concurrent program : Interface trip stop --> Completed with Warining
    in inventory where do you check this transaction.
    Please let me know the Navigation
    regds
    MRR

    Hi MRR,
    depending on the nature of the Warning and system setup you might want to look at:
    Inventory>Transaction>Pending Transactions
    or
    Inventory>Transactions>Transaction Open Interface.
    Is it an Internal Order or a regular Sales Order?
    Have you Opened the Invetory Txn periods for the given inventory organization etc.
    You should take a look at Oracle Diagnostics where there are specific report to troubleshoot Interface Trip related issues.
    For 11i the note 179661.1 gives a list of available Tests. Also follow links if you need R12.
    /Niels LM

  • Interface trip stop not running on ship confirm

    Version: 11.5.10.2.
    Hi Guys
    While ship confirming the orders, for some of them, interface trip stop is not automatically running which keeps the order status " shipped" and the order does not become eligible for running autoinvoice.
    We have to unassign it from trip and autocreate delivery manually. from actions menu.
    This is not happening for all the orders, this is happening for some of them.
    What can be the root cause ? Please assist.
    Note:
    Defer interfaces is already unchecked.
    Regards
    Nouman Shaikh

    While processing ship confim, the interface trip stop request does not initiate by itself for some of the orders.
    What can cause it ?
    In such situation, we need to manually autocreate trip.
    What can be the reason behind it ? How to avoid it.
    I believe this is an an effective community.
    Regards
    Nouman Shaikh

  • What does 'SRS' mean in request 'Interface Trip Stop - SRS'?

    hi.
    What does 'SRS' mean in request 'Interface Trip Stop - SRS'?
    why it is added? Is there any special meaning?
    thank you
    Peter

    Use in SRS (System Administrator > Concurrent > Program > Define).
    Check this box to indicate that users can submit a request to run this program from a Standard Request Submission window.
    If you check this box, you must register your program parameters, if any, in the Parameters window accessed from the button at the bottom of this window.
    Oracle Applications System Administrator's Documentation Set
    http://download-uk.oracle.com/docs/cd/B25516_14/current/html/docset.html

  • Interface Trip Stop Completed with Warning

    Hi All,
    For a sales order the line has been shipped where as the line status is showning as Picked and the delivery status is closed with the next step is showing as "Run Interface". While I have submitted the Interface Trip Stop, it completed with warning. The log file says:
    Shipping Execution: Version : 12.0.0
    Copyright (c) 1979, 1999, Oracle Corporation. All rights reserved.
    WSHINTERFACES module: Interface Trip Stop - SRS
    Current system time is 20-APR-2009 07:31:03
    **Starts**20-APR-2009 07:31:03
    **Ends**20-APR-2009 07:31:03
    Interface trip stop is completed with warning
    Start of log messages from FND_FILE
    Starting WSH Debugger ==> 04/20/2009 07:31:03 AM,Session ID=2850630
    The following are the current Shipping related debug settings:
    OM: Debug Level ==> 0
    INV: Debug Level ==>
    WSH: Debug Enabled ==> Yes
    WSH: Debug File Prefix ==>
    WSH: Debug Level ==> Statement
    WSH: Debug Log Directory ==> /dtmp
    WSH: Debug Module ==> %
    Entering WSH_SHIP_CONFIRM_ACTIONS.INTERFACE_ALL_WRP (WSHDDSHB.pls 120.19.12010000.3) (04/20/2009 07:31:03 AM)
    P_MODE ==> ALL
    P_STOP_ID ==> is NULL
    P_DELIVERY_ID ==> 2888
    P_LOG_LEVEL ==> 1
    p_organization_id ==> 381
    p_num_requests ==> 1
    p_stops_per_batch ==> 1
    l_req_data ==>
    Entering WSH_SHIP_CONFIRM_ACTIONS.INTERFACE_ALL (WSHDDSHB.pls 120.19.12010000.3) (04/20/2009 07:31:03 AM)
    P_MODE ==> ALL
    P_STOP_ID ==> is NULL
    P_DELIVERY_ID ==> 2888
    P_LOG_LEVEL ==> 1
    p_organization_id ==> 381
    p_stops_per_batch ==> 1
    INTERFACETRIPSTOP: FINDING STOP FOR DELIVERY_ID 2888
    l_stop_id ==> 3031
    InterfaceTripStop: processing stop_id 3031 for INV OM DSNO
    l_inv_interface ==> 1
    l_om_interface ==> 1
    l_dsno_interface ==> 1
    l_interface_mode ==> INV OM DSNO
    l_stop_id ==> 3031
    l_override_wf ==> N
    Ship to Deliver Workflow is enabled for one or more deliveries related to this Stop ==>
    Ship to Deliver Workflow is enabled for one or more deliveries related to this S
    top
    Interface_All: skipping stop_id 3031
    ========================================================================
    l_stops_count ==> 0
    InterfaceTripStop: no stop is processed because no lines are eligble for interfa
    cing.
    errbuf ==> Interface trip stop is completed with warning
    retcode ==> 1
    l_completion_status ==> WARNING
    Exiting WSH_SHIP_CONFIRM_ACTIONS.INTERFACE_ALL (04/20/2009 07:31:03 AM, .01 seconds)
    Automatic clean up ==>
    l_recs = 0 ==>
    errbuf ==> Interface trip stop is completed with warning
    retcode ==> 1
    l_completion_status ==> NORMAL
    Exiting WSH_SHIP_CONFIRM_ACTIONS.INTERFACE_ALL_WRP (04/20/2009 07:31:03 AM, .03 seconds)
    ************Summary of Shipping API Calls************
    WSH_SHIP_CONFIRM_ACTIONS.INTERFACE_ALL_WRP : 1 calls : .03 seconds
    WSH_SHIP_CONFIRM_ACTIONS.INTERFACE_ALL : 1 calls : .01 seconds
    Thanks in advance for your help.
    Regards,
    Jyoti
    Edited by: Jyoti.Mohanty on Apr 20, 2009 2:46 AM

    Hi,
    This problem is documented in 785934.1 (Metalink doc).
    Summary of the solution is given below. Please make sure you read the above document to confirm that the solution applies to your environment.
    1. Go into the responsibility: System Administrator.
    2. Navigate to Profile > System.
    3. Query the profile option 'WSH: Override Ship to Deliver Workflow' and set this value to 'Yes'
    at the Site Level.
    4. Retest the issue.
    5. Migrate the solution as appropriate to other environments

  • Quesiton about Interface Trip Stop

    We have a situation where our actual shipping is done by a third party. Consultants wrote two interfaces....one to create a file to be shiped once things are pick released, and another to import a file that will ship comfirm the same lines.
    We had a situation where we were backed up for a while.
    Essentially, we imported some files that were to ship confirm a lot of picked orders. I believe what happened were that they closed a lot of deliveries, but there were shipping exceptions so that even though they were closed, the corresponding order lines are still in a picked status. I'm guessing what happened was that the ITS wasn't run for these, and that's why they're where they are.
    So, a lot of the exceptions were invalid tp dates, so I went ahead and closed all of those. But...I still need the order lines to close.
    Can I run ITS blind, and if so will it work for all eligible deliveries, or do I have to run it for each delivery manually?
    If I can run it wide open, will it only effect those deliveries that are eligible (i.e., only those that are ship confirmed)?
    thanks for any guidance!!
    -jerry

    Hi Jerry,
    I can't see any reason not to run it blind if you have 100s of deliveries for which the order lines need closing. As you surmise, it will just ignore anything ineligible. If you are still getting exceptions though, you might want to hone in more on where any problems lie ... i.e. run in debug mode and up your OM: Debug level to 5 so that you can see something meaningful in the output log for individual deliveries/trip stops.
    One small caveat - if you're not supplying a trip stop or delivery in the ITS parameters then depending on your setup (i.e. if you have multiple orgs with their own shipping) you might want to at least populate the shipping warehouse in the organization parameter rather than run truly 'blind'.
    It sounds as if your problems have all been in the DSNO part of the interface with tp date exceptions. I'm sure you're already aware that it's also possible to run the 3 parts of the ITS separately if necessary for troubleshooting ... lots of help on MOS for that.
    Good luck...!
    Jon

  • Why am I receiving the "Unfortunately, Messaging has stopped" error message and how do I fix it?

    Why am I receiving the "Unfortunately, Messaging has stopped" error message and how do I fix it?

    I am so upset. Please read my messages from my postings. This has nothing to do with SIM Card, Hard Reset, Apps, Google Gmail Account, nothing. I have gone thru all of this and NOTHING has fixed this. I went to the store today and spoke to the manager on duty. He said he had to try and duplicate the problem before he could help me. I showed him "screen captures" I did, told him it's out here on the board, etc. etc. Needless to say I ended up coming home with the same phone, "he" erased the phone and started over again. Well guess what, it's not a error with "MY" Gmail account being corrupted because if that is the case Mrs. Hayden14 has a bad Gmail account too. If you guessed it, the phone just crashed again! I was able this time to capture a report with ALL the history in it and saved screen captures to PROVE to him this is not a joke. Even the report says "Crash". This time it was something else I don't even or ever have used. I have also wasted over a day , yes a full work day on this without question.
    I have had to get the run around for the last day. This is totally ridiculous, including them putting me on hold for 55 min. Oh, that's another funny story. Anyways, tomorrow morning I am going to the Verizon store one last and final time and I hope they decided to do the right thing and give me a phone that does not crash and works. It would be handy at work for me, especially where I work at. I hope hope hope someone listens to and helps me. I would love for them to see me walk in, take my phone and say to me were going to get you another phone, hand it to me, see if it works and prove it's the device. I don't hear anyone having this issue on other phone types so sounds like its the phone type.
    I have had 3 phones now in the matter of 2 weeks. I am sure the FedEx charges will add up to a cost of a new phone at some point and start to outbalance your requirement to give me the same phone when it has the same problem.
    Can't wait to see what happens tomorrow.

  • MSI K9A Platinum and VIA drivers issue? XP 0x0000007B stop error.

    I get a Windows Stop error when trying to boot into Windows XP with new components. The SATA hard drive (and Windows XP installation) is from the old computer.
    The new computer components are:
    MB: MSI K9A Platinum, chipset: RD580 (North Bridge), SB600 (South Bridge)
    CPU: AMD Athlon 64 x2 5600+, boxed (the cooler and fan came with the CPU).
    Video: MSI Radeon 1950 XTX
    The old (and working) computer setup is:
    OS: XP Professional
    MB: Abit AV8-3rd Eye, chipset: VIA K8T800Pro + VT8237
    CPU: AMD Athlon 64 3500+
    Video: Sapphire Radeon 9800Pro All-in-Wonder, videodriver: atidvag.dll version 6.14.10.6542
    HD: Maxtor 6B200M0 SCSI Disk Device
    BIOS: Phoenix 6.00PG 20.04.2005
    System drivers with "via" in the name: VIAAGP1.SYS, viaide.sys, viasride.sys
    VIA 4in1 (Hyperion) version: 4.55 (that can be found at HKEY_Local_Machine\Software\Via4in1Driver).
    VIA 2.20e SATA/RAID driver was used when installing this computer setup.
    The precise stop error is:
    0x0000007B (0xba4c3528, 0xc0000034, 0x00000000, 0x00000000)
    From many sites I have gathered that the error is related to Windows XP not being able to access a critical system drive. Most probably the SATA hard drive issue.
    The problem probably is the VIA drivers of the old motherboard and/or the SATA driver.
    First I should mention, that MSI K9A Platinum does not have a hard disk SATA driver. If it does, I have been unable to find one. Certainly no such floppy disk included, and no such driver in the MSI's Web page for this motherboard.
    Second important point: I never used RAID. I did use VIA 2.20e SATA/RAID driver disk when installing Windows XP to the old computer.
    Strange that the hard drive model is reported as a "SCSI Disk Device". It's not a SCSI drive however: it's a SATA disk.
    I have tried to uninstal the motherboard chipset drivers (Hyperion v4.55), but there seems to be a bug here: the drivers should be uninstalled using the installation program, and select the uninstall option. However, I do not get the uninstallation option to choose at all! Yes, I'm using the normal installation mode, not the quick installation (although tried that, too). The Hyperion setup program just installs, and asks to reboot the computer. After rebooting and trying again, it still does not offer me an uninstallation choise.
    I know how to install hard drive VIA SATA driver, but I have no idea how to uninstall it. And I'm afraid to do that without certainty that it IS the solution, since I could not access the hard drive any more in the old computer setup (and return to read this forum). Also, I do not have a floppy drive any more. Anyone know if there is an issue with K9A and XP having VIA SATA driver installed?
    When I tried the new computer setup, I first tried the simplest possible hardware combination: there were no CD/DVD-drives, no (parallel)IDE hard drives, and no PCI cards, except the MSI video adapter.
    My BIOS Setup experiments. None of these helped: got the same stop error each time.
    1) I didn't much touch the BIOS setting first. Just tried to boot with the settings BIOS came with.
    2) Next I disabled the integrated audio, LAN and IEE1394 devices and floppy drive and disabled all other choises except the SATA drive as a boot device.
    3) Next I tried with the fail-safe BIOS defaults.
    4) Cleared CMOS.
    5) Changed OnChip SATA type from Native IDE to Legacy IDE. (Only one boot attempt with the setting as Legacy.)
    6) Disabled PCI IDE BusMaster.
    7) Never touched anything in the Cell Menu: so the settings are in minimum.
    A step I have taken after the last attempt: run Windows XP hard drive error-checking tool to every logical drive with the fix option selected, and the system drive also with scan the bad sectors option selected.
    My plans next are:
    1) to install a newer Hyperion driver. If that would correct the no-unistallation-choice-bug,
    2) to disable USB-devices in the BIOS (desperate),
    3) to choose the Windows general video display driver (although I seriously doubt this is a display driver problem!).
    4) to uninstall the Anti-Virus software (Avira Antivir).
    I've read a numerous Web pages so far about the 0x0000007B stop error. Here are some links:
    Quote
    http://www.seagate.com/www/en-us/support/knowledge_base/
    Stop 0x0000007B or INACCESSIBLE_BOOT_DEVICE
    This Stop message, also known as Stop 0x7B, indicates that Windows XP Professional lost access to the system volume or boot volume during the startup process. This error always occurs while the system is starting and is often caused by one of the following:
        * Hardware problems
        * Corrupted or incompatible storage drivers
        * File system problems
        * Boot sector viruses
        * Outdated firmware
    During I/O system initialization, this error can occur when:
        * The controller or driver for the startup device (typically the hard disk) failed to initialize the necessary hardware.
        * File system initialization failed because the system did not recognize the data on the boot device.
    Quote
    http://support.microsoft.com/kb/314082
    You receive a Stop 0x0000007B error after you move the Windows XP system disk to another computer
    SYMPTOMS
    After you move the Microsoft Windows XP system (boot) disk to a backup computer, you may receive the following Stop error when you try to start the Windows XP-based backup computer:
    STOP: 0x0000007B (0xF741B84C,0xC0000034,0x00000000,0x00000000)
    CAUSE
    This error may occur if the registry entries and the drivers for the mass storage controller hardware in the backup computer are not installed in Windows XP.
    RESOLUTION
    To resolve this error, use the same hardware for the backup computer.
    Heh, heh! Very nice Microsoft, but I plan to update my computer, so I NEED to use different components
    Quote
    http://support.microsoft.com/kb/324103
    Device Driver Issues
    You may receive a "Stop 0x0000007B" error message in the following scenarios:
    •   A device driver that the computer boot controller needs is not configured to start during the startup process.
    •   A device driver that the computer boot controller needs is corrupted.
    •   Information in the Windows XP registry (information related to how the device drivers load during startup) is corrupted.
    Hardware Issues
    You may receive a "Stop 0x0000007B" error message if there is a resource conflict between the boot controller and another controller or between SCSI devices. You may also receive this Stop error message if drive translation is not being performed or if drive translation was changed. To troubleshoot this issue:
    1.   If an IRQ or I/O port address conflict exists between the boot controller and another controller, Windows XP either stops responding (hangs) or displays a "Stop 0x0000007B" error message. If you recently added new hardware, remove the new hardware or reconfigure it so that it does not conflict with the resources of any other installed controllers.
    2.   If you are using a SCSI hard disk, check the SCSI chain for correct termination. Remove any unused SCSI devices or make sure that each SCSI ID is unique.
    3.   Make sure that drive translation is turned on (if it is required) and that it has not been changed. For example, if you recently switched controllers, this issue may occur. For additional information about this issue, click the following article number to view the article in the Microsoft Knowledge Base: 314082.
    Quote
    http://support.microsoft.com/kb/316401/
    SYMPTOMS
    When you start your Microsoft Windows XP-based computer after you replace the motherboard on the computer, you may receive a Stop error message that is similar to the following:
    STOP 0x0000007B INACCESSABLE_BOOT_DEVICE
    CAUSE
    This issue may occur if the new motherboard contains an embedded IDE controller that has a different chipset than the original motherboard.
    RESOLUTION
    Method 1: Perform an in-place upgrade of Windows XP [<- That means repair installation of Windows XP]
    •   Do not use a repair or in-place upgrade if you suspect disk problems.
    Method 2: Repartition and format your hard disk and reinstall Windows XP

    Alright I got the situation over.
    Quote from: Roskaposti on 19-May-07, 04:44:59
    My plans next are:
    1) to install a newer Hyperion driver. If that would correct the no-unistallation-choice-bug,
    2) to disable USB-devices in the BIOS (desperate),
    3) to choose the Windows general video display driver (although I seriously doubt this is a display driver problem!).
    4) to uninstall the Anti-Virus software (Avira Antivir).
    I did try all all the above, and none of them helped.
    And by the way: after installing the new Hyperion (VIA chipset drivers), I was finally able to also uninstall. It also uninstalled the IDE SATA (I think) and PATA drivers.
    But what I had to do, was to make a REPAIR installation of Windows XP.
    So, I was wondering now afterwards: this is really, really silly. Why the hell we need to re-install Windows if we move the SYSTEM SATA drive to another computer? We don't have similar problem with parallel IDE drives. Whom should we thank here??
    The issue is to insert the driver files and the information of the ide drivers Windows should use with the next boot. How can it be this difficult?
    What you basically need is..
    - the information about the new chipset's PCIIDE.SYS/[VENDOR_PROVIDED_FILE].SYS and ATAPIIDE.SYS inserted into the values in HKEY_LOCAL_MACHINE\SYSTEM\ControlSetXXX\Control\CriticalDeviceDatabase
    - and the vendor's IDE drivers to the %SYSTEMROOT%/System32/drivers folder.
    Maybe something else, I don't know. But the problem was, Windows didn't know how, or what drivers to use. That can't be so big problem you need to install the whole OS anew!

  • Error in using BAPI_CONFEC_CREATE : Interface data contains Errors

    Hi,
    I am using this BAPI BAPI_CONFEC_CREATE to create confirmations locally in SRM for a PO. I am following Documentation available for this BAPI.  But when I excuted with below data getting error " INTERFACE DATA CONTAINS ERRORS"
    I am passing these data:
    Hedaer: Ref_doc_no - PO Number
                  Description:
                 Process Type: "CONF"
    Header_cust:  parent_guid : PO GUID
    Item: Parent: PO Header GUID
            PO Number: PO number
            PO GUID: PO HEDAER GUD
            PO ITEM Number: PO item Number
           PO_ITEM_GUID: po item guid
    Account:
                   Parent_GUID : PO Item GUID
                   G/L acct : Po G/l acct
                   cost center : PO cost center
    what are the data sholud be passed to this BAPI?
    Am I missing any input data to this BAPI? Please let me know.
    Am I using correct Function Module to create a confirmation for a PO in Stand alone scenario?
    Thanks.
    Shears
    Edited by: Shears80 on Sep 10, 2010 1:39 AM

    Hi Matt
    I'm using the same FM but it's not working. Can you please share what data you are passing in the FM.
    After debugging I found that my confirmation is getting created but it's not getting saved.
    Please enlighten me.
    Thanks
    Ankit

  • PC getting Stop error when connecting iTouch

    I have a 2nd generation iTouch that I sync'd up to my pc with no problem when I first got it about 2 weeks ago. Now everytime I connect it, I get the blue screen with a stop error. My daughter also has an iTouch (1st generation) and I can connect that one with no issues. Any ideas on what to do? I repaired iTunes but really didn't want to uninstall and it seems to be just my iTouch. I can connect it to my work laptop to charge with no issues too.

    Well, the other USB port was working for a while. Now none work. When I plug my iTouch in, I get the Windows XP stop error and the blue screen of death. The USB port works for other things like my jump drive. I can plug my iTouch into my laptop and all is fine. I recently upgraded my iTouch to 3.0 but it still worked after doing that. Do you think my USB drivers need to be upgraded?

  • My Computer crashes when i connect my Ipod. (Stop error, Blue Screen)

    For the past 3 weeks, my computer has been crashing regularly-- and it's due to the iPod. When i connect my ipod, iTunes starts up and as soon as it starts to Sync, it "blue screen crashes (see message below). When i run iTunes w/o the iPod connected, no issues and i can also use my iPod no issues:
    The Message i get is below: ..its a Stop error:
    * STOP 0x0000008e (0xc0000005, 0xBFA6FCBA, 0xA9F5130C, 0x00000000)
    * Ati3duag.dll -- Address BFA6FCBA Base at BFA1C000 DateStamp 3eade1b1
    Please help me!!
    Gateway Laptop Windows XP Pro

    i am having the same problem, but cant even get on my pc now with out using a system recovery disc! im really stuck and hope someone knows of a way of sorting this as i have only had it 2 weeks!! many thanks

  • STOP ERROR - Blue Screen - on Lap Top - Fixed, tear1, support rocks!!!!!!

    New Iphone, and new laptop, installed itunes Noprob,
    Hooked Iphone to usb laptop found Iphone and installed and activated Noprob,All systems go, I am loving it.
    I then ejected my Iphone and hooked up my Ipod to transfer purchesed music and shows transfered Noprob, so I eject my Ipod to hook up my Iphone to put my purchesed music on it.
    THATS when it happened.
    STOP ERROR- Blue screen,cpu restarted on its own.
    I deleted itunes and I deleted camradrives, printer drivers.
    I tried allmost everything and still got the same blue screen.
    To make a long story shorter I called apple talked to the (now this is important) Iphone/Itunes department they are seperate but have a div. that works as one but you have to ask for the department that takes care of both or you will talk to both or 3 or 4 other dept.
    Tear 1 Support had me do a soft reset on my phone it did not work so I backed up my phone # and they showed me how to do a compleate reset and it worked.
    I have been Error and blue screen free for 2 days and I feel very posative about the future with my relationship between my cpu and my phone
    Thank you for your time.
    I hope I help some one I found no relief here with my problem but its a great resource for information
    GOD BLESS TEAR 1 SUPPORT YOUR TEAM ROCK'S
    Pro-Iceman
    Anacotes,Wa

    You don't need to upgrade your software.  But if you're struggling with Spry, IMO you should cut your losses and switch to something better for the longrun.
    If you have a budget to work with, I highly recommend Project Seven's Pop-Menu Magic 3.  It's easy to use in DW CS4, 5, 6 or CC.  More importantly, it's bullet proof and works in all devices. 
    Pop-Menu  Magic3 by PVII (commercial DW extension)
    http://www.projectseven.com/products/menusystems/pmm3/index.htm
    If you don't have a budget to work with, you can roll your own menus with jQuery plugins.  A bit more effort on your part, but they perform better than Spry.
    jQuery Superfish
    http://users.tpg.com.au/j_birch/plugins/superfish/
    jQuery MegaMenu2
    DEMO:
    http://www.geektantra.com/projects/jquery-megamenu-2/
    DOWNLOAD:
    http://code.google.com/p/jquery-megamenu/
    Nancy O.

  • ITunes Stop Error

    Ok ever since last night, every time i open iTunes i get a stop error on a blue screen causing my computer to restart. The error is 0x0000008E. CAN SOMEONE PLEASE HELP ME?

    I figured it out, it was just permissions on the drives..

Maybe you are looking for