Intermittant radio interface down on 1130 APs

I am having unified wireless installation, with WiSM on 6500 at central site and around 90 nos of 1130 APs located at remote locations ( over WAN) as well as some APs locate in the same location.
The APs are configured in WCS, using default AP template.
Alsomot all APs are showing minor alarms saying " radio interface threshold violated".
In addition, a major alarm posted frequently on WCS saying "radion interface down".
Cleints are complaining that they are loosing connectkion momentarily but connected again automatically wo WLAN. But they will have to log in to application programs in such cases.
a.Does anybody have similar experience, and
b. What are the best settings for 1130 APs trhat we have to do explicitly in setting up the WCS template ?
Thanks ,

Might be due to interference and the fact that RRM is enalbled and the ap's are changing channels causing the radios to shut down temporarily. Either set the channel or try to change the threshold.
Here is the error info:
http://www.cisco.com/en/US/docs/wireless/wcs/4.2/configuration/guide/wcsevent.html#wp1139158

Similar Messages

  • Radio Interface Reset and Shutdown Frequently

    As recently new office from end-Sept, we have found that the radio interface reset very frequently which has been  happening about over 15 times within 8 weeks for one AP on average. Some of  those (3 AP so far) got the radio interface down eventually and we need to  reload the AP to make it up again.
    the AP model is AIR-LAP1142N-N-K9 and the IOS version is
    /* Style Definitions */
    table.MsoNormalTable
    {mso-style-name:表格內文;
    mso-tstyle-rowband-size:0;
    mso-tstyle-colband-size:0;
    mso-style-noshow:yes;
    mso-style-parent:"";
    mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
    mso-para-margin:0cm;
    mso-para-margin-bottom:.0001pt;
    mso-pagination:widow-orphan;
    font-size:10.0pt;
    font-family:"Times New Roman";
    mso-fareast-font-family:"Times New Roman";
    mso-ansi-language:#0400;
    mso-fareast-language:#0400;
    mso-bidi-language:#0400;}
    st1\:*{behavior:url(#ieooui) }
    /* Style Definitions */
    table.MsoNormalTable
    {mso-style-name:表格內文;
    mso-tstyle-rowband-size:0;
    mso-tstyle-colband-size:0;
    mso-style-noshow:yes;
    mso-style-parent:"";
    mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
    mso-para-margin:0cm;
    mso-para-margin-bottom:.0001pt;
    mso-pagination:widow-orphan;
    font-size:10.0pt;
    font-family:"Times New Roman";
    mso-fareast-font-family:"Times New Roman";
    mso-ansi-language:#0400;
    mso-fareast-language:#0400;
    mso-bidi-language:#0400;}
    c1140-k9w7-mx.124-21a.JA1. Power supply is made from the PoE switch c2960s. Is there any issue related to IOS? or some other factors may cause the issue happen? Any debug command can show the status of AP? Please advice.

    Hi Surendra,
    Other than IOS, will this radio interface reset and shutdown issue affect by the nearby AP which is not belongs to the same office.
    /* Style Definitions */
    table.MsoNormalTable
    {mso-style-name:"Table Normal";
    mso-tstyle-rowband-size:0;
    mso-tstyle-colband-size:0;
    mso-style-noshow:yes;
    mso-style-parent:"";
    mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
    mso-para-margin:0cm;
    mso-para-margin-bottom:.0001pt;
    mso-pagination:widow-orphan;
    font-size:10.0pt;
    font-family:"Times New Roman";
    mso-fareast-font-family:"Times New Roman";
    mso-ansi-language:#0400;
    mso-fareast-language:#0400;
    mso-bidi-language:#0400;}
    Scenario:
    The new office gets 2 floors. One is 5/F which has installed 9 APs with different channels and another one is 6/F which has installed 6 APs with different channels as well. We found that there are many events “%DOT11-4-MAXRETRIES: Packet to client reached max retries, removing the client” logged on 5/F and 6/F AP.
    We also found that the radio interface reset very frequently which has been happening about over 15 times within 8 weeks for one AP on average. Some of those (3 AP so far) got the radio interface down eventually and we need to reload the AP to make it up again.
    Is/ are there any possibility caused by otherenvironmental factors? Please advise.
    Best regards,
    Bell

  • Cisco Wireless AP radio interface shutdown/Operation Status Down

    Hi,
    I am trying to troubleshoot the cause of the wireless AP 1142 radio shutdown; I was wondering where may be a good place to start on it/possibility of the radio shutting down. Once the radio is shown as down; I would just need to re-enable (disable/enable) it and the status changes to up status. I have attached a screen catpure of the radio interface showning down.
    The AP radios shutting down is intermittent; some APs has their "A/N" radio interface shutdown while others has their "G/N" radio interface shutdown. Not too sure what may most likely be causing it to shutdown?
    Any input is appreciated.
    Thanks.

    Do you have controller ?? if yes then posts out put of sh sysinfo commad.
    Paste the output of sh version command from AP.
    Also check: 
    1. Choose Wireless > 802.11a/n or 802.11b/g/n > Network
    Select the 802.11a (or 802.11b/g) Network Status check box to enable the 802.11a or 802.11b/g band.
    2. Wireless > Access Points > All APs then click on specific AP and make sure admin status is enable.
    Reagrds

  • Spotify Now Playing out of sync with Radio Interface / Unable to Thumbs Up-Down current song

    So this is probably happened 10 or more times and I finally got annoyed enough to record my screen to show it happening. What happens is I will be listening to a song on a spotify radio station (I pay for premium) and decide I don't like it and open up the Spotify UI to thumbs it down. However when I click on the "Radio" sidebar option it won't show the song that is playing even though I KNOW it's playing from the radio. Even worse if I try to advance the track the track it says it's playing in the Radio interface DOES NOT match "Now Playing" in the bottom corner of the UI OR the OS X Notifications. This video only shows the notifications because I didn't want to have to expose more friends names or more private playlists (and radio station) names but the Now Playing matches the OS X Notification. VIDEO  PS: Clicking "New Message" while logged out gives you some crypitc message about not having your email verified? WTF? VIDEO PPS: The "Autosaved at XX:XX XX" message above this text box I'm typing in that pops in and out very often is VERY **bleep**ING ANNOYING. Do it below, off to the side, or silently.. good god... VIDEO  PPPS: Ok, **bleep** you spotify https://s.joshstrange.com/DoId.png I'll post dropbox links... Way to wait until after uploading them to do any checking...

    This is a deeper issue than just that. Queueing songs remotely doesn't work right, just try itRunning radio remotely doesn't allow you to thumbs up tracks because it always displays an off-by-one track (I have to VNC to my mac, where the actual playback is happening)Different parts of the interface (when connected remotely) sometimes display the right information, but none of it is actionable (for example, I'd like to thumbs-up tracks, and thumbs-down tracks from my phone or spotify client on my laptop). This kind of makes creating a good radio station using connect impossible.Connect isn't ready for prime time. It's nice to have, but if I have to connect to the screen of the actual player, it defeats the entire purpose. I don't want a VNC connection open all the time.

  • Dot11 radio interface reset protocol down

    I have a cisco 1400 that that show interface show int dott1 radio interface reset protocol down. I had a surge in the area and had the problem after. I copied the config over to a new Ap and power injector and the problem persists. The bridge is the non root bridge. I had read a caveat cscea75989 but it said take no action. Take no action is not fixing my problem at this time. Any suggestions would be appreciated. Thanks.

    There are a number of known issues on this. One which sounds similar is CSCea45031. Check if you are hitting the same.

  • Radio interface need to be disabled when antenna is not present?

    I have been informed within a training class that the radio interface of an access point should be disabled when an antenna is not present. The reason given was that it would protect the radio from being adversely affected (potetnial for irreparable conditions). Question: 1) Is this true? 2) If so, where can I find supporting documentation on CCO? (I have not been able to find corroboratory information.)

    Hi Vincent,
    Here is a doc that speaks to this issue ( I don't see this causing irreparable damage but, better safe than sorry :)
    Q. If you operate the radio but do not attach the antenna, can you damage the radio?
    A. Some radio equipment manufacturers specifically warn against the operation of radios without the attachment of the antenna. Operation without the antenna can damage the transmitter. Most pieces of amateur or commercial radio equipment carry this warning because the equipment operates at a much higher transmitter power. A failure to use a proper antenna or load causes a reflected wave standing wave ratio (SWR) that can damage the final amplifier stage. This final amplifier stage is the power amplifier (PA).
    For Cisco Aironet equipment, the transmitter power output is 100 milliwatts (mW) for the 350 Series and 30 mW for the 340 Series. Damage is unlikely, but possible. If you need to run the devices without antennae, turn the transmitter power down to 1.5 mW. Also, you can use a 50/52 ohm dummy load (attenuator) to be safe.
    From this good Q & A doc;
    http://www.cisco.com/en/US/products/hw/wireless/ps441/products_qanda_item09186a0080094d01.shtml#aps
    Hope this helps!
    Rob

  • Wireless AP will not connect and Radios stay down

    Hi,
    I have recently configured a Wireless AP for our network. It is running flash:/c1140-k9w7-mx.124-21a.JA1/c1140-k9w7-mx.124-21a.JA1" .
    I have configured the SSID's VLANS, subinterfaces BVI's etc. I have connected it to our switch infrastructure but i cannot seem to connect to it and the Radio interface is staying down.
    Wireless AP Config:
    dot11 ssid IMC-Wireless-Data
       vlan 10
       authentication open
       authentication network-eap AUTHVPN
    dot11 ssid IMC-Wireless-Voice
       vlan 14
       authentication open
       authentication network-eap AUTHVPN
    interface Dot11Radio0
    no ip address
    no ip route-cache
    shutdown
    antenna gain 0
    station-role root
    bridge-group 1
    bridge-group 1 subscriber-loop-control
    bridge-group 1 block-unknown-source
    no bridge-group 1 source-learning
    no bridge-group 1 unicast-flooding
    bridge-group 1 spanning-disabled
    interface Dot11Radio1
    no ip address
    no ip route-cache
    antenna gain 0
    no dfs band block
    channel dfs
    station-role root
    interface Dot11Radio1.10
    encapsulation dot1Q 10 native
    no ip route-cache
    bridge-group 10
    bridge-group 10 subscriber-loop-control
    bridge-group 10 block-unknown-source
    no bridge-group 10 source-learning
    no bridge-group 10 unicast-flooding
    bridge-group 10 spanning-disabled
    interface Dot11Radio1.14
    encapsulation dot1Q 14
    no ip route-cache
    bridge-group 14
    bridge-group 14 subscriber-loop-control
    bridge-group 14 block-unknown-source
    no bridge-group 14 source-learning
    no bridge-group 14 unicast-flooding
    bridge-group 14 spanning-disabled
    interface GigabitEthernet0
    description IMC-Wireless-Data
    no ip address
    no ip route-cache
    duplex auto
    speed auto
    no keepalive
    interface GigabitEthernet0.10
    description IMC-Wireless-Data
    encapsulation dot1Q 10 native
    no ip route-cache
    bridge-group 10
    no bridge-group 10 source-learning
    bridge-group 10 spanning-disabled
    interface GigabitEthernet0.14
    description IMC-Wireless-Voice
    encapsulation dot1Q 14
    no ip route-cache
    bridge-group 14
    no bridge-group 14 source-learning
    bridge-group 14 spanning-disabled
    interface BVI1
    description IMC-Wireless-Data
    no ip address
    no ip route-cache
    interface BVI10
    description IMC-Wireless-Data
    ip address 10.10.0.245 255.255.255.0
    no ip route-cache
    interface BVI14
    description IMC-Wireless-Voice
    ip address 10.10.14.251 255.255.255.0
    no ip route-cache
    ip default-gateway 10.10.0.254
    SwitchPort Config:
    ================
    interface GigabitEthernet0/2
    description IMC-SYD-AP01
    switchport trunk encapsulation dot1q
    switchport trunk allowed vlan 10,14
    switchport mode trunk
    mls qos trust dscp
    no mdix auto
    spanning-tree portfast
    Core Switch Vlan configuration:
    interface Vlan10
    description IMC-Switch1 - Data VLAN
    ip address 10.10.0.252 255.255.255.0
    standby 10 ip 10.10.0.254
    standby 10 priority 110
    standby 10 preempt
    end
    interface Vlan14
    description IMC-Wireless-Voice
    ip address 10.10.14.252 255.255.255.0
    standby 14 ip 10.10.14.254
    standby 14 priority 110
    standby 14 preempt
    The Logs in the AP come up as :
    000022: *Mar  1 11:15:05.211 AEDT: %DOT11-4-NO_SSID_VLAN: No SSID with VLAN configured. Dot11Radio1 not started.
    000023: *Mar  1 11:15:05.212 AEDT: %DOT11-4-NO_SSID_VLAN: No SSID with VLAN configured. Dot11Radio1 not started.
    If anyone has any idea why this is an issue it would be greatly appreciated.
    Thanks

    Hi,
    Pleas do the below changes..
    en
    conf t
    int dot11 1
    ssid IMC-Wireless-Data
    ssid IMC-Wireless-Voice
    no shut
    end
    en
    conf t
    int dot11 1.10
    encap dot1q native 10
    bridge-group 1
    end
    en
    conf t
    int gig 0.10
    encap dot1q native 10
    bridge-group 1
    end
    On the Switch
    ===========
    interface GigabitEthernet0/2
    description IMC-SYD-AP01
    switchport trunk encapsulation dot1q
    switchport trunk allowed vlan 10,14
    switchport trunk native vlan 10
    switchport mode trunk
    mls qos trust dscp
    no mdix auto
    spanning-tree portfast
    lemme know if this helps and please dont forget to rate the usefull posts!!
    Regards
    Surendra

  • Cisco 1142AP Autonomous - Radio interface constantly reset and provides crash file

    Hello All,
    We have 10 Cisco 1142 Access Points currently configured as Autonomous and I'm experiecing very unusual behavior with the 2.4GHz radio interfaces on each of them. The IOS firmware is 15.2.2JB and they're connected to Cisco 2960 PoE switches. I'm not sure what could be causing this problem however it is service impacting and looks bad on me since I don't have a solution for it. One potential fix could be to upgrade the firmware to 15.2.4 but I'm sure if it is a firmware problem. Any advice would help. Here's an excerpt from the AP log:
    Aug 18 14:40:16:  Writing driver stats to flash:/ap_log_r0_0.log..
    Aug 18 14:40:21:
    Aug 18 14:40:21: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    Aug 18 14:40:22: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    Aug 18 14:40:23: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
    Aug 18 14:40:23: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
    Thanks,
    Ali Ibrahim

    You should be able to go in and view teh R0_0.log file.
    there might be something in there that you can do a bug search for.
    HTH,
    Steve

  • AP show in WLC but no radio interfaces

    I am have a problem with couple of our APs the model is AIR-LAP1131AG-A-K9 and we have a Cisco 4404 WLC. 2 of them show up on the controller but have no radio interfaces. I have a I have restarted the AP, reset to factory config all to no avail. When I restart or reset it does communicate with the controller, but still no a/b/g/n radios.
    Anyone have any ideas? Here is a snippet from the log when I restart the AP.
    I would appreciate and pointers here.
    Mar 24 14:20:23.948: [ERROR] spam_lrad.c 2016: AP 00:1d:a2:80:75:dc associated. Last AP failure was due to Link Failure
    Mar 24 14:20:23.948 apf_api.c:23237 APF-3-INVALID_RADIO_TYPE: Invalid radio type 255 received.
    Mar 24 14:20:23.948 apf_api.c:23224 APF-3-INVALID_RADIO_TYPE: Invalid radio type 255 received.
    Mar 24 14:20:23.947 apf_api.c:23237 APF-3-INVALID_RADIO_TYPE: Invalid radio type 255 received.
    Mar 24 14:20:23.947 apf_api.c:23224 APF-3-INVALID_RADIO_TYPE: Invalid radio type 255 received.
    Mar 24 14:20:23.947 apf_api.c:23237 APF-3-INVALID_RADIO_TYPE: Invalid radio type 255 received.
    Mar 24 14:20:23.947 apf_api.c:23224 APF-3-INVALID_RADIO_TYPE: Invalid radio type 255 received.
    Mar 24 14:20:23.947 apf_api.c:23237 APF-3-INVALID_RADIO_TYPE: Invalid radio type 255 received.
    Mar 24 14:20:23.947 apf_api.c:23224 APF-3-INVALID_RADIO_TYPE: Invalid radio type 255 received.
    Mar 24 14:20:23.947 apf_api.c:23237 APF-3-INVALID_RADIO_TYPE: Invalid radio type 255 received.
    Mar 24 14:20:23.947 apf_api.c:23224 APF-3-INVALID_RADIO_TYPE: Invalid radio type 255 received.
    Mar 24 14:20:23.947 apf_api.c:23237 APF-3-INVALID_RADIO_TYPE: Invalid radio type 255 received.
    Mar 24 14:20:23.947 apf_api.c:23224 APF-3-INVALID_RADIO_TYPE: Invalid radio type 255 received.
    Mar 24 14:20:23.947 apf_api.c:23237 APF-3-INVALID_RADIO_TYPE: Invalid radio type 255 received.
    Mar 24 14:20:23.947 apf_api.c:23224 APF-3-INVALID_RADIO_TYPE: Invalid radio type 255 received.
    Mar 24 14:20:23.946 apf_api.c:23237 APF-3-INVALID_RADIO_TYPE: Invalid radio type 255 received.
    Mar 24 14:20:23.946 apf_api.c:23224 APF-3-INVALID_RADIO_TYPE: Invalid radio type 255 received.
    Mar 24 14:20:23.946 apf_api.c:23237 APF-3-INVALID_RADIO_TYPE: Invalid radio type 255 received.
    Mar 24 14:20:23.946 apf_api.c:23224 APF-3-INVALID_RADIO_TYPE: Invalid radio type 255 received.
    Mar 24 14:20:23.946 apf_api.c:23237 APF-3-INVALID_RADIO_TYPE: Invalid radio type 255 received.
    Mar 24 14:20:23.946 apf_api.c:23224 APF-3-INVALID_RADIO_TYPE: Invalid radio type 255 received.
    Mar 24 14:20:23.903: [ERROR] spam_lrad.c 7012: 00:1d:a2:80:75:dc AP Country changed from:() to (US ).
    Mar 24 14:20:23.903: [ERROR] spam_lrad.c 6694: AP 00:1d:a2:80:75:dc: Invalid country code ().
    Mar 24 14:20:23.902: [ERROR] spam_lrad.c 7012: 00:1d:a2:80:75:dc AP Country changed from:() to (US ).
    Mar 24 14:20:23.902: [ERROR] spam_lrad.c 6694: AP 00:1d:a2:80:75:dc: Invalid country code ().

    Hi Rob,
    The WLC version is 4.1.171.0. I have been browsing the conversations here and there seems to a few that are having similar issues. I can't find anything related to this except this:
    CSCsl90841-After you upgrade a controller to software release 4.2.61.0, any access point that does not have region coding (such as the Airespace 1250 access point) is unable to join the controller. An "Invalid country code" message with a country code of 0xFFFF appears in the output of the debug lwapp events enable command.
    Workaround: Downgrade the controller to software release 4.1.
    And I am already on that version. This is rather bizarre. I am working from home for the next few day so I can't physically go pull the AP to look at the codes.
    It does associate with the controller but it just doesn't show any radio interfaces ie, a/b/g/n.
    When I go in and look at that AP on the controller it show everything including the country fine except for the radios. Very confusing.

  • IOS 1230 AP Radio shuts down

    I have a unique problem in which I have my Cisco SE involved in trying to correct. When using an IOS based 1230 AP in one of my locations the RADIO interface will turn off (shut down) even though it appears as being up. All associatins are lost and the only way to reassociate to the AP is by restarting the AP. I have the latest code running for the Vxworks 1200 AP and this problem does not happen. I also have the IOS based 1230 AP deployed at all my other locations with zero problems. Cisco has provided me with a spectrum analyzer thinking it was some interference, but we have not seen any interference. Is anyone else having this problem? Please reply of e-mail me I would love to discuss this with you.
    PK

    Hmm... I have had problems with the 802.11a (5Ghz) radio shutting down. It just says something like "DOT11-RADIO-FAILED" I believe in the logs and shows that it was down. Had the unit replaced once and the problem seemed to go away for quite awhile but did notice the radio failed again last week sometime and had to reboot again.
    I thought it might be heat related since it was mounted on a "cloth" wall without the right mounting bracket and might have had the vents covered, but that's not the case now.

  • Radio Interface Locks Up, Jams Up Clients

    Hi there, got a problem with the radio interface on AP350s and 1200s (11b & g, running IOS), occasionally (and not on the same units) the RF interface will lock up and any clients associated to it will not be pingable and lose network connectivity. Doing a shut/no shut (and usually a reload) bumps the clients off to other APs where they're pingable once more. This happens to Cisco and non-Cisco radioed devices, the APs aren't running anything fancy like WDS, just default config. and WEP. The 350s never had this problem running VxWorks but started this behavior when upgraded to IOS. I'm real disappinted the 1200s are doing the same thing. When the lock ups happen it causes major problems at our locations and I need to find a cure...now! Any ideas anyone? Thanks.

    Scott,
    The 350s use the IOS upgrade image, the 1200s use the latest IOS version. The only rogue APs I have problems with are the Ciscos running IOS! Symbol and first generation 802.11b Aironet (pre-Cisco) APs aren't afflicted with this problem even in a mixed AP environment. In locations that are all Cisco APs and devices we still get this problem. The APs are in locations countrywide and away from Joe Public, and no other WLANs nearby. I think, I HOPE it's just a config. problem but all the APs have (more or less) the same standard config. and the issue strikes APs randomly. As advised, as soon as you do a shut/no shut everything's OK...the devices that got bumped off by the s/ns usually 'roam' back to the AP that had the issue within a few seconds or minutes and are pingable once more from the AP's radio interface. I was paged while typing my question last evening and when I went to check, guess what, another 350 with 6 clients (all Cisco devices) all jammed up on it. Shut/No Shut and carry on like nothing happened. If you've got any suggestions I'll take them, I've not had much luck on the Cisco web site, I'll probably have to put in a TAC case at some point soon as I've got better things to do than go around resetting APs. I was even thinking about rebooting our Cisco AP complement once a week in case it was some sort of caching/ARP problem.
    Thanks in advance for any pearls of wisdom!

  • My magic mouse behaves erratically with intermittent problems - slows down, right click doesn't work, disconnects for a few seconds then reconnects. Anyone suggest what I could do to fix this?

    My magic mouse behaves erratically with intermittent problems - slows down, right click doesn't work, disconnects for a few seconds then reconnects. Anyone suggest what I could do to fix this?

    I just figured out the print quality issue for my wife with her new iMac and new printer.
    She replaced both at once and she couldn't understand why her Artisan 730 was lower quality then her Epson R280 when they had the same specs.
    Turns out the newer printer had the option to connect via wifi which we used during setup.
    The driver options are completely different depending on how you connect.
    Once I connected via USB the correct options were available and the print quality was better.
    Looking at the R2400 it dies not have wifi, but while researching the problem for my wife someone esle was having an issue updating to the latest printer driver.
    If you go into the print utility from the Printer and Scanner system preference and under the general tab you should have driver 5.5.
    One user had to delete the old printer driver before Software Update loaded the newer printer driver.
    https://discussions.apple.com/message/15947486#15947486
    On my MacBook Pro (w Snow Leopard) I always had to reconnect my wifi at home when it woke up. I upgraded my router from an old Netgear to a newer N D-Link and stopped having to do that.
    I would be surprised you would have that problem with an Airport Extreme, you might check to see if there is a firmware update for it.

  • AP "A" Radio is Down

    AP is connected to 6500 switch with "inline power" turned off. Using the supplied power supply to power the AP unit. B/G radio shows up but A radio shows down. WCS 4.2

    I figured it out. I did not enable it on the controller side.

  • Unidentified traps and interface down alerts LMS 4.2

    Hi all,
    Sometimes we have unidentified traps in our log, we don't know where they come from.
    In high severity faults we see an active alert with device name “Unidentified” event name unresponsive but with a certain ip address.
    What are these alerts about? Can I filter them?
    A second issue I have is that I get interface down alerts. But when we log on to the device, there is no interface down at all. We can also ping the device from the lms server at that time. I have been told that the admin state and operational state has to be up.
    Thanks,
    Best Regards,
    Joris

    Hi Joris,
    Generic trap support is a new feature introduced in LMS 4.2 release. look at the below
    document also.
    http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/4.2/user/guide/lms_monitor/TrapFwd.html#wpxref13049
    LMS 4.2 release onwards DFM will display any unprocessed traps comming from device in
    fault monitor screen as unidentified trap under Inform alarm.
    For the other issue , it could be a DFM database issue , try to REDISCOVER those devices in
    DFM and see how it works
    Thanks
    Afroz

  • Apple TV radio shuts down after 10 minutes

    Apple TV radio shuts down after 10 minutes.  Can not find out why.  Could version 7.0 be the problem?

    Welcome to the Apple Community.
    Seems to be an issue for a large number of users, probably need to wait for a fix.

Maybe you are looking for