Intermittent Connection with WRT54G

Hi, I'm new here, so my apologies for any redundancy / lack of techno-savvy.
I have had my two home computers hooked up to the internet (ethernet) via a WRT54G v.8 router for a couple of months now. It worked well for about a week before the wireless signal started disappearing and I'd have to re-set the whole network: at first every few days, and then a couple of times a day. I tried all the troubleshooting tips on this website: upgraded firmware, MAC address cloning, changing the channel, you name it. Finally the only thing that worked was disconnecting the wired connection from my desktop and making that computer wireless too, so I figured it must be some sort of problem caused by the computer's internet settings.
That worked for a month or so, but now I'm having the same problem again. The wireless signal will just quit for no apparent reason. Sometimes if I wait (anywhere from 15 minutes to 2 hours) the signal will come back again with all the network settings intact. Another thing that *sometimes* works is resetting the router manually.
Anybody have any ideas about what's going on?
Oh, and the computers are a Toshiba satellite and an HP Pavilion.

hi!
well, if you said that you have done everything that you need to do on the router like upgrade, reconfigure, change channels and everything.how bout the laptop?are they using the wireless utility for their built-in wireless adapter or the windows xp configuration.they sometimes will have conflict and if you use these laptops in connecting to other wifi area then when you get home, try removing the preferred networks and reconnect to your network.hope that will help you a bit.goodluck!

Similar Messages

Intermittent connection with WRT54GS (v. 6)

I got this router about six months ago, and it used to be disconnected somehow from the Internet about once a week. All I'd have to do to fix it would be unplug it for a few seconds. This past week, though, the router has been going out a few times a day. Again, fixing it only requires unplugging it for a few seconds ( 10 ), but it's usually only a few hours until it goes out again. The router is in another room, but it's connection to this computer is wired. Does anyone have any ideas on what might be causing this?

I've also tried updating the firmware, but that doesn't seem to have helped...

Dropping Connection with WRT54GS v4

I have had a problem for the last week where my router drops connection intermittently about every 20-30 minutes. Once it drops, I have to unplug the router and modem and start over. It happens over and over again. Hooking up directly to the modem results in a normal, trouble-free connection. I have tried changing the channel, the SSID name and restarting everything sequentially without success. Any ideas on how to fix this would be greatly appreciated.

i started getting this problem, or at least a similar one, lately. i have a WRT54GS v6 with the latest firmware (1.50.9) that randomly decides to stop allowing wireless connections. devices that are already connected will stay connected and be able to access the internet through it, but if you restart a computer or try to connect with other devices, it doesn't find the router.
i have changed the SSID and set it so it does not broadcast the SSID, but that shouldn't cause it to stop accepting connections. i usually only have my laptop and a couple wii's connected to the router (my own and 2 of my roommates).
the only way to fix it when this happens is to unplug the router and plug it back in.

Intermittent connection with netgear1000 and orange, please help

Hi there,
I bought a mbp 2011 and installed orange broadband with netgear1000. I am having intermittent connection, anyone has an idea?
Thanks for the help would be much appreciated.
Lebake

1.with ur laptop wired to the rtr, open IE. in the address bar, type http://192.168.1.1. it will ask for authentication. leave ther username blank and in password type admin.
2.on the setup page, click on the tab wireless and then select manual setup
3.change the w/l n/w name to ur preference, radio band to standard 20 mhz and standard channel to 6 and then save settings.
4. click on subtab w/l security, change the security mode to wep and in the key type any 10 digit no. and make sure this is ur password for the w/l. Then save settings
5.now try to connect to this w/l n/w on ur laptop
6. for ur PS3, go to n/w settings-internet connection settings-custom-and enterv the w/l settings manually.
Linksys Setup CD said "Use Win XP or better"
So i installed Linux

Unstable WPA connection with WRT54G 2.2 (firmware 4.30.5)

Hello everybody,
I'm experiencing some unstability in my wireless connection with my WRT54G router.
By the past, the router was working perfectly. Last week I've upgraded the firmware to the version 4.30.5. Since then I have to power off the router every morning to connect my Centrino laptop to it.
FYI, my router is a WRT54G model 2.2. I'm using Mixed Mode (B+G) + WPA2 Personal (TKIP+AES) with a Group Key Renewal = 3600 seconds. My router is using the wifi channel 4 and there is no other access point on this channel. On my laptop, I'm running a Windows XP SP2 with the latest system patches.
Please also note that my router is now identifying itself as a WRT54GL (in its web pages) and not just WRT54G. Not sure if it's an issue or not.
Any help will be greatly appreciated.
Thank you in advance,
PatrickMessage Edited by pbateman on 11-07-200601:54 AM

You mean that on the setup page of the router its says WRT54GL instead of the actual model?
When you try to turn off your router are you still wilrelessly connected?
"Give them nothing... But take from them everything..."
-Leonidas "300"

DNS lost connection with WRT54G

I have the following problem with my WRT54G v.8 router. Sometimes when I turn on on the computer I can not access the internet. I am using a wireless connection using Vista. Running the diagnose and repair option in Vista it says there is not connection with DNS. I make a ping to the router and it is ok, ping to the cable modem and it is ok, and obviously ping to DNS and they don´t answer. After powering off and powering on the router I have again the internet connection. After some days or sessions the problem repeats. Maybe somebody have a solution for this kind of problem.

hi... try upgrading/reflashing firmware on the router, go to www.linksys.com/download and download the latest firmware for the router, after reflashing firmware on the router, reset the router back to factory default settings and logon to router's setup page, reconfigure it according to ISP settings, reduce MTU to 1458, go to wireless settings try changing wireless channel to 11, go to advanced wireless settings and reduce beacon interval to 50, fragmentation and RTS threshold to 2304...check whether it works or not...

MacBookPro intermittent connectivity with AE/Internet alongside XP/Vista

My family has 3 laptops: 1x Dell (XP), 1x Toshiba (Vista) and MacBook Pro (OSX10.5.6) using my home wireless network: Airport Express connected to VirginMedia Router to internet. Only Mac has intermittent problems:
- All 3 laptops individually have no problems connecting to internet;
- All 3 can simultaneously be on the internet streaming online media;
- However, only Mac has intermittent connection problems;
- The XP/Vista laptops connectivity is faultless, unaffected when Mac is first connected to or using the AE/internet;
- If my Mac is already connected to AE/internet, then connecting XP/Vista laptop will interrupt Mac connection;
- Turning the Airport-client off/on sometimes temporarily re-connects, or once in a while Mac auto-connects for a few mins, but reconnection is not maintained for more than a few minutes, whether internet in use or not;
- Mac alone will remain on internet happily indefinitely if neither XP/Vista laptop are connected;
- I have tried fixes suggested in the forums, such as renewing/lengthening DHCP lease, using DHCP and hard IP addresses, different AE wireless frequencies, removing wireless phones, updating Airport software to latest, turning IPv6 off, etc.
- This issue arises even when all 3 laptops are used in same room, less than 10m line-of-sight from AE.
Any ideas how I can force my Mac to stay connected to AE/Internet and not let my XP/Vista family members win the contest of reliable connectivity?
Yours, the embarassed of the family.

Thanks for the first two replies.
1. Norton and AVG antivirus ran last night.   No problems. Spybot also was run.   So I don't think the problem is related to Arun's ideas.
2. I have a MI424WR Verizon router.   The WAN light is on solid green, all the time. The Internet light flashes.
The router is fed by coax.
I dont know what bit torrent is.   Computer 2 is only used for Pogo on line simple stupid gaming (I am whining about wife's activities).   My Computer 1 is only used for ebay and simple web activities.
I tried resetting the router once today...helped nothing.
Just now I could not get connected via shortcuts.   BUT---I can always get on line through Outlook Express. And I got here via an email link.
go figure

Remote Desktop Connection with WRT54G from Novice

Well, I’m usually pretty good at using Google and forums to eventually figure out how to fix my problem but this one absolutely has me stumped and I’m hoping someone out there has an answer for me. For the record, I have probably a beginner/intermediate knowledge of computers so if you know the answer to my problem, try to explain it simply! ****TO ANYONE WHO TAKES THE TIME TO READ THIS THING AND CAN OFFER SOME ADVICE-THANK YOU!!!!***
THE PROBLEM
I would like to be able to use Remote Desktop to log into either of my home computers from basically any computer on the internet.
THE SETUP
I have two computers, whose names are LAPTOP and DESKTOP that are both running Windows Vista Ultimate. Both of the computers are connected to a Linksys WRt54G Router ; one wired, the other wirelessly. The Linksys router is then connected to a Westell DSL Modem that connects to AT&T’s internet service.
SETTINGS
My DSL service only provides me with a dynamic IP address so I signed up with no-ip.com. Through that site, I bought a domain name and downloaded their small program that runs in the background of my desktop computer. The program checks what my IP address is every couple of seconds and if it changes, it notifies their server so that anyone who types in my domain name is directed to the new IP address.
ROUTER (Firmware 4.20.6)
Basic Setup Page: The Router Name is just the model number, the Server Name is my DSL provider and the Domain Name is the name I chose and registered with No-IP.com. (www.mydomainname.com, for example.) DHCP Server is ENABLED. DDNS Service is DISABLED. Under Advanced Routing, it is set in GATEWAY mode.
Security Page: Firewall Protection is ENABLED. Block Anonymous Internet Requests is NOT checked. Filter Multicast, Filter Internet NAT Redirection and Filter IDENT ARE checked.
Applications and Gaming Page: I chose two port numbers, one for each computer that I want to connect to. On the first line, I have Application: RDP, Port Range: 49200 to 49200, Protocol: Both, IP Address (The IP address of the computer I want to connect to) and the Enable box IS checked. [I did the same thing with the second line for the other computer, but with a different port number and that computer’s IP address)
Administration Page: Access Server is HTTP, Wireless Access Web is ENABLED, Remote Management is ENABLED through Port 8080, and UPnP is ENABLED.
WINDOWS VISTA SETTINGS
First, I went to the Remote Desktop Settings of the target computer and ENABLED Remote Desktop Connection and allowed computers running any version of Windows. I also confirmed that the box labeled “Allow This Computer To Be Controlled Remotely” WAS checked. I then made sure that I had a user name, it had a password associated and that it had Administrator priveledges. I went back to the Remote Connections screen and added the user name as being allowed to connect. (I think this is redundant since it’s both the owner of the computer and has Administrator Status.)
Next, per Randomly Googled Internet Advice, I went into the registry and changed the port number that Remote Desktop listens for incoming connections to Port 49200 to match the router settings. [Registry Entry that I modified was: HKEY_LOCAL_MACHINE\System\CurrentControlSet\Control\Terminal Server\WinStations\RDP-Tcp]
Finally, I went to the Windows Firewall and Added (opened) port 49200 for use as a Remote Connection. I kept the protocol as TCP and confirmed the scope was set for Any Computer.
CURRENT STATUS
If I go to Explorer and enter my IP address with a colon and the specify port 8080, I can get the login screen for the router. Same thing happens if I just enter my domain name and port 8080. However, if I switch the 8080 port and use one of the ports I chose (49200), it cannot connect, either using the Public IP address or the domain name. (I’m trying to connect using a wireless card and not connected to my local network so I know it’s the same as if I was anywhere else.)
I’m not sure why it won’t let me connect; it feels like the router will not allow the connection to pass through it to the port I’m asking it to forward to. I’m guessing someone out there who took the time to read it is shaking their head at all the information I provided and knows the one dumb thing I missed!
Thanks again!

I'm attempting to do the same thing with my home network. the only differences are that i have cable internet from comcast and i'm running vista business. my router is the wrt54gs. i'm assuming that the web page is similar for adjustmants. To be honest i cannot figure out how to do a remote destop too. so i went to www.logmein.com and installed the program. once installed to to every computer you want to have access too and log into the website. then click on the add computer icom. full control app sharing etc... even better when you connect you have the option to deactivate the local host mouse and screen to prevent anyone seeing what your doing.
If you resolve the router issue would you let me know. plz thanks
Forest

Problem WRV200 Connect With WRT54G v.5

Hello to Everybody,
First of all, I'm sorry about my English -not the Best.
-- i wrote this message in Camera Forum Too.
and now to my problem,
i purchased the IP Camera Model WVC200 and i Installed it Perfect.
i can view, move, record and etc.
i connect it to Edimax Wireless Router.
all the function is work perfectly.
When i come back to my home, and tried to connect to the camera - i failed.
i connect to the internet by WRT54G Router I'm my home. i tried all the options possible in the setup page of the Router, Update Router Firmware and nothing is not success...
while i decide to disconnect the router and connect my computer direct to Modem i was Surprised! i can connect to the camera.
i disconnect again and connected my computer via the Router.
i changed the port of camera to 80, not yet.
Just i enter the IP with Port Number in my browser - i get the small screen that i need to enter my username and password - i entered and
wait ... wait ... wait .... wait ..... and nothing is happened. The title of the browser is changed and enough
Friends,
What i need to do ?
I hopeless.
Moshe

Hi… You need to forward the port 1024 on this router and then try to access it again.

Problems getting a connection with WRT54G Ver. 8

Okay.. This may be a little long.
I had my router set up for about 2 years now. It worked fine up until 2 days ago. I have a WRT54G V8 router, with a Belkin wireless receiver for another desktop computer. I have tried using the 192.168.1.1 website to set up on my wireless computer to try and set up the IP address, but it does not seem to be working at all. The IP remains to be 0.0.0.0 and would not change after changing the MAC address, and using Release/Renew option. The desktop computer that the router is hooked up to doesn't even recognize 192.168.1.1 website into the browser. I have tried reconnecting the router, as well as the Broadband modem that we have and nothing seems to get the connection to my other desktop. Can anyone help me get my connection running again? It would be greatly appreciate.

Your Modem should be connected to the Linksys Router on the Internet Port and then you need to connect your Computer to the Linksys Router on the LAN Port 1.... Then Connect the Power to the Router.... Check the Light Status (Power, WLAN, Port no.1 and Internet) all this lights should be Lid...
If your Internet Service Providor is Cable follow this link
If your Internet Service Providor is DSL follow this link

Very Low Connection with WRT54GS / WMP54GS

I have a WRT54GS Router in one brick building and a WMP54GS adapter about 60 ft. away in another brick building. What is the effective range in this situation. I'm getting a "very Low" signal. Also, I had problems setting this network up. In order to get the adapter to work I had to change the channel on the router from (default 6) to channel 2. Does this have something to do with my low signal? Any help would be appreciated!
Thanks

the 3 channels that do not interfere with each other are 1,6 and 11. 6 is the cleanest channel being in the middle of the band, but is the most popular. have you tried using only the windows utility to manage your wireless connection? this has been known to rectify poor wireless performance.
Regards, Carl.
www.thibor.co.uk
Hyperwrt Dev for the WRT300N, WRTSL54GS, WRT54GS/G/GL

Intermittent connectivity with router

I have a Belkin N wireless router. I used to have a Linksys wireless B. Both of these routers seem to have the same issue, or so I believe. When connected to the router, wired or wirelessly my internet connectivity is very intermittent. Sometimes the pages load lightening fast then I'll click another link and it will hang for about a minute then load the page the way dial up modems used to. It does it intermittently with any page I go to its not site specific.
I removed the modem from the router and plugged it directly to my Mac Mini and it works perfectly. By the way I also have a Tivo, an iPhone and two laptops on the same network. They are all connected wirelessly and work flawlessly. It also does not matter if the other computers are connected or not the same issues occur.

I forgot to mention that sometimes when its hanging on one page I can click another link and it will load instantaneously. This must be the most frustrating think I've ever encountered on a computer.

Very slow connection with WRT54GS.

It appeared out of nowhere 2 days ago... slow connection for websites, very high latency for online games to a point where it's unplayable... i tried to reset my router, change channel(i'm usually at channel 6), moving the antennas... nothing. when i reset, the speed is fine for a few minutes, but after a while it's back to slow connection. My router isn't even 1 year old yet and it's already broken? I can't believe that, there must be some solution. Anyone can help please?

The latest firmware is 1.02.0 if you have wrt54gs v6 & V5 if yout got v7 the latest firmware is 7.50.0
First step you need to check is your direct connection from the modem.
1. hardwire your computer straight to the modem using a cat 5 ethernet cable, if your download speed and your internet connection is slow, the problem is with the modem or with your ISP so you need to call your ISP and double check your connection.
If your speed if fine straight to the modem then its with the router.
2.Hardwire your computer straight to the router if your speed is fine when its hardwired through the router, then the problem is with your wireless card or the wireless settings of the router.
In US the standard channel is 11,6 and 1. So play around with the channel. If its still doesnt work then access the setup page of your router click on the WIRELESS tab click on ADVANCE WIRELESS SETTINGS sub tab. set beacon interval to 50, RTS and Fragmentation Threshold to 2304.
After that turn off the modem the router and your computer for 1min. After a minute turn on the modem first after lights of your modem are steady, turn on the router and lastly turn on your computer, check your connection if its fine then its fixed if not call linksys tech support.
I hope this would help. Good Luck!

Sharing DSL internet connection with WRT54G

I've recently changed from a cable to a DSL internet connection.
On cable I used a WRT54G router to share the connection to a laptop (via Wireless) and a desktop (via ethernet cable).
After instaling the DSL (modem and software) on the laptop, the conection doesn't work.
The set up for the linksys router was updated (changed to PPPoE, and informing the user id and password the provider gave me), via browser, and it is correct.
Now, I can only access the internet when the ethernet cable is connected straight from the DSL modem to the laptop.
If change the cable from the laptop to the linksys router and try accessing the router, it doesn't work, although the connection is indicated as active, and the laptop gets the ip I defined in the DHCP linksys router (192.168.1.100).
Under this scheme, it seems the laptop can't find, neither the linksys router, nor the DSL modem (modem model is Thomson Speed Touch 510 v6), and hence, the internet.
Due to that when I try accessing the Linksys configuration page (192.168.1.1) I receive a message that this page cannot be accessed offline and it's necessary to connect. I can't connect, cause the modem is not found in the net.
That should not happen, the page should be available offline, cause it's a connection that does not rely on an internet connection (the router is close to the laptop).
The same problem occurs with any web page I try to open/load: a message stated it can be accessed offline, and it's necessary to connect, but, again, I can't connect.
I tried using a cable between the laptop and the linksys router, but did not go any better.
Thx everyone

It is my understanding that the Thompson Speed Touch 510 V6 is an ADSL Gateway modem router. As such, at a minumum, it is probably doing your PPPoE login for you. If this is correct, then your Linksys should not be set to do a PPPoE login. When you used software to install your modem, didn't you have to enter your user id and password and have it loaded into the Thompson? If the Thompson has this info, the Linksys pobably does not need it.
You really need to talk to your DSL provider, or check their web site, to see what they suggest about setting up your system. At a minumum, you will need to know exactly what the Thompson is doing:
Is it doing your PPPoE login?
Is is acting as a DHCP server?
In the mean time, you might just want to try the following:
Try setting the router to "Automatic Configuration - DHCP"
If you are having trouble getting to the router setup page, do the following:
1) power down your modem, router, and computers, and unplug them from the wall.
2) disconnect all wires from the router.
3) connect one computer by wire to port 1 (not the internet port) on the router.
3) power up the router and allow it to fully boot (1-2 minutes).
4) power up the computer
5) open your browser and point it to 192.168.1.1 This should open the router login window. Enter your user name (if any) and password. This should take you to your router's setup page.
If you get this far, set the router to "Automatic Configuration - DHCP", save the setting, then power down the router and your computer. Then reconnect modem-router-computer and try your setup again.
If any step fails, note the exact error message and the status of the lights on the router. Report back with your results. Also, it might help if we knew your DSL service provider.
Hope this helps.
Message Edited by toomanydonuts on 12-23-200602:29 AM
Message Edited by toomanydonuts on 12-23-200602:31 AM

Slow wired connection with WRT54G

My ISP is Comcast.
I'm using their modem which includes my digital voice connection. From there I'm wired straight to the WRT54G and from there I'm wired to my PC. However, when I connect from the Comcast modem to my PC I get download speeds of 12mbps and when I connect from the WRT54G (wired) it drops to 1mbps or even 786kbps.
I've tried resetting the modem and the router. I've tried changing the MTU. I have the latest firmware version (v8.0.2). The last resort is getting a new cable modem (suggested in the forums) but I think that's out of the question since my digital voice is connected to the Comcast modem.
Any other suggestions? Thanks in advance!

Please state the make and exact model number of your modem (not the WRT54G).
Using an ethernet cable, wire your computer directly to the modem (not the WRT54G). Verify that you have a properly working Internet connection. Then do the following:
Go to "Start" > All Programs > Accessories > Command Prompt.
A black DOS box will appear. Type in "ipconfig /all" (with no quotes), then hit the Enter key. Copy all the results to your next post, except that if your "IP address" does not start with 192, then post only the first 3 digits of your "IP address" along with the rest of the info.

Intermittent Connection with WRT54G

Similar Messages

Maybe you are looking for