Intermittent start up problem

Sometimes our Mac mini just does nothing. The cable to the PSU is hot. I tried resetting the PMU and even pulled out the logic board battery to reset that too. Still doesn't work.
Then a wee while later it does start up.
Any ideas? There don't seem to be many problems with them but this one stumps me.
aedan

hey, this might not be the most helpful advice, but hey. Ive had the same problem with my mac mini, and i have phoned up apple many times about it. Run an extended Hardware test from the discs that came with it, repair disc persmissions stuff like that. If that doesnt do anything (like mine) take it to an apple repair shop. Do you have applecare?

Similar Messages

Start-up problem with hp pavilion dv6t-7000‏: "Boot Device Not Found. Hard Disk (3F0)" error

I started getting start-up problems with my hp pavilion dv6t-7000‏. It happens intermittently.
The boot error is:
Boot Device Not Found
   Please install an operating system on your hard disk.
   Hard Disk (3F0)
   F2 System Diagnostics
   For more information, please visit: www.hp.com/go/techcenter/startup
Could a faulty BIOS update cause this problem?
Anyone else who may have experienced a similar problem?
I'd appreciate any help about this problem. Thanks.

Hi
Please find the link given below might help you to fix your issue.
Resolve Boot Device not Found Error Message
Let us know how it goes!
"I work for HP."
****Click the (purple thumbs up icon in the lower right corner of a post) to say thanks****
****Please mark Accept As Solution if it solves your problem****
Regards
Manjunath

Intermittent sound & voice problems

I have been having Intermittent sound & voice problems
During the last week when making receiving the voice and sound from the speaker is distorted on both ends of the conversation
I have to restart the mobile and it works fine for a day or so then starts again
I reset the phone to factory setting and it seems to have no effect
Has anyone else had these problems?

http://www.sonymobile.com/global-en/support/contact-us/
Update Service (SUS)
PC Companion (PCC)
Bridge (for Mac)
Alternatives on How to backup Xperias
http://talk.sonymobile.com/thread/36355
"I'd rather be hated for who I am, than loved for who I am not." Kurt Cobain (1967-1994)

Start up problems, including from installation disc.

Hello everyone in the Apple ether, I need your help!
I have a powerpc based iMac G5 at home that I set up for my mum to use once I bought my macbook. I finally managed to win her over with talks of how much easier it would be for her to manage her photos in iPhoto, and everything was going really well. I recently came home after my final year at uni and some travelling to find that the computer is taking a long time to start up. This can be in both the grey apple loading screen but also once it logs in it can take a long time to display anything over than the desktop background, and even once it displays other items any attempt to open anything just results in a spinning wheel icon. At the worst case it has taken about 20 minutes to get going.
Once it has fully booted, the machine doesn't appear to be working any slower than normal. I tried using disk utility in mac OSX and verifying permissions etc and that didn't do anything. I then tried googling the problem and came across this article on the apple web site. http://support.apple.com/kb/TS1417
Starting in Safe Mode did not resolve the issue so after backing everything up I tried starting from the installation disc. This is not something I have ever done before and as someone that never really delves beneath the surface of her machines I was a bit scared of doing it. But I put the disc in and restarted and held down C just after I heard the chime, and shortly after it all went wrong. The screen went grey and all I could see was the image you get when it crashes (you know, the power sign with text over it saying you need to restart) with lines of code all down the left of the screen. I took a photo of the screen on my camera so can give details of the code if you need them. The last line said
Kernel version:
Darwin Kernel Version 8.8.3: Wed Oct 18 22:00:38 PDT 2006; root:xnu-792.15.4.obj-4/RELEASE_PPC
panic: We are hanging here...
After a few minutes on this screen the fan started working overtime and after about 5 minutes of that I just turned it off using the power button on the back. The machine has since started up normally (ie slowly) but is working fine.
So I was wondering if anyone had any ideas how to fix the slow start up problem without booting from my install disc, or indeed if anyone could suggest why I can't boot from my install disc? Thanks very much for your time and help.

It appears you experienced a kernel panic which is hardware related. A few suggestions for you to try:
Except for the keyboard & mouse, disconnect all devices from the computer & try the suggestions mentioned in the following:
http://docs.info.apple.com/article.html?artnum=106805 Mac OS X: "Broken folder" icon, prohibitory sign, or *kernel panic* when computer starts
User Tips: Kernel Panics
==============
Boot up from your Tiger or Leopard Install DVD while holding down the "c" key.
Select the language you wish to use, and then choose *"Disk Utility"* from the menu bar.
Your HD should appear in a panel on the left hand side of the window which opens. Select it and then click on the *"repair disk"* button in the right hand section of the window.
Once this process has been completed restart your computer and run *repair permissions* from Disk Utility.
* If Disk Utility (from the install DVD or HD)is unable to complete the repair, you will need to use a stronger 3rd party utility like DiskWarrior, Techtool PRO (not Deluxe) or Drive Genius.
=============
How much HD space is left on the iMac?
How much RAM is installed?
==============
Which "model" & "generation" G5 iMac does your mother have?
Need this info so that the knowledgeable users can provide you with the proper troubleshooting solution(s).
http://docs.info.apple.com/article.html?artnum=301724-en How to identify your iMac
http://docs.info.apple.com/article.html?path=Mac/10.4/en/mh355.html Getting information about your computer
You can have this info displayed on the bottom of every post by going to 'My Settings' which is located in the column on the right under your name, and filling in the information asked for.
Thank you

I had an iphone 4 and when I downloaded the IOS7 started having problems. Gone the phone keypad, could not type more names of my contacts in the phone search. I decided to buy the iphone 5S and since downloaded the IOS7.1.2 the search of yo

I had an iphone 4 and when I downloaded the IOS7 started having problems. Gone the phone keypad, could not type more names of my contacts in the phone search. I decided to buy the iphone 5S and since downloaded the IOS7.1.2 the search of your phone contacts it takes to open or write

dedegodoy wrote:
I decided to buy the iphone 5S and since downloaded the IOS7.1.2 the search of your phone contacts it takes to open or write
What does that mean? What is your technical support question?

Photo Gallery start up problem

I have a glitch and it's probably me … but here's what
I know.
About Don Booth's Photo Gallery:
It's great. Everything is good - integrated with my CSS -
looks nice.
When the page loads all is well except the first image in the
Gallery does not display in <div id="mainImageOutline"... (and
the first thumbnail is not highlighted). While I'm building and
testing this is OK. Just click a thumbnail and everything works
well.
In the demo, the Gallery is operational by default and starts
up with the first thumbnail and Spry:detail produces the
corresponding image (automatically). That's what I want.
About my code:
Except for a couple of "page layout" divs that I have,
consistent with my own site-wide style sheet conventions, such as
<div id="wrapper"> and <div id="maincontent"> I have:
1. Copied Don Booth's xhtml code directly from the
Spry_1_1_022408 download sample.
2. Copied Don Booth's css code directly from the same
download sample.
3. Copied Don Booth's gallery.js directly (without change as
far as I know).
The only significant change (apart from CSS and xhtml
structure) in my work is - I added an additional Spry:detail div to
present additional datapoints from xml. This is not relevant to my
question because the issue that concerns me is consistent if I
remove this second detail div. The start-up problem remains.
The URL for the gallery page in question is:
http://www.yhqg.org/Celebration/quiltshow2008/galleryix/gallery.htm
I imagine the problem is in gallery.js. You should know that
javascript is a bit like dungeons and dragons to me.
I have an error report:
Error: dsPhotos is not defined
Source File:
http://www.yhqg.org/Celebration/quiltshow2008/galleryix/includes/gallery.js
Line: 55
So, when I see:
var gAutoStartSlideShow;
if (gAutoStartSlideShow == undefined)
gAutoStartSlideShow = true;
I imagine I'm looking at something useful but I don't know
what to do with it, or if it is the right code to focus on. I
respect the relationship with level 4 support engineers, but after
trying to solve my own issue for a few weeks I decided it was time
to submit my question. How do I get Photo Gallery to start up like
the demo?
Additional information:
There is also a series of error reports that show when the
Gallery is playing (for example):
Warning: Expected end of value for property but found
'-0.0775'. Error in parsing value for property 'opacity'.
Declaration dropped.
Source File:
http://www.yhqg.org/Celebration/quiltshow2008/galleryix/gallery.htm
Line: 0
I don't think it is related, but that's what I know.
I tried to copy my xhtml (below) but it caused this message
to exceed allowed size. But I don't see that xhtml is the problem.
You can see the source at the URL (above).

Hi Latauro,
Sounds like you need to turn your Slideshow into a Track, and then set the Track to display as 16:9 Letterbox; but first, you'll also need to encode your slides as wide Mpeg 2 clips (encode set to 16:9), too; to whatever duration you have them set in the Slideshow, currently (if they're not already wide encoded clips).
It would be good to stick some same duration audible or silent same format and bit rate audio underneath each of the new movie slides, to present players a nicely packed VOB.
Take care,
Trai Forrester
TFDVD Research Labs
http://www.DVDVerification.com
PS. If this helps you, would you please remember to declare the thread as "Solved". Although probably hopeless, someone should make a run to try and catch up with good Drew!! (see what happens Hal, when you take some time off?!

Start up problem Nokia 2520

Hi,
My 2 weeks old Nokia Lumia 2520 has a start up problem. When I switch on the phone I only see a blue screen with an unhappy smiley face :-(
The battery is fully charged and I tried holding the 'power on'button for 10 seconds, but it doesn't work. Anyone knows what to try next?

I tried holding the 'volume down' and 'power on' buttun simultaniously, but it is still not starting properly. Now I am getting an exclamation mark....

Start-up problem keys won't work

Hello out there,
I have another start-up problem with a G5 2.0 GHz (7.2).
I can't use any start-up keys (such as holding c oder s).
I can't reset PRAM. Starting from CD works only when I unplug the hard drive. The keyboard works fine than.
Any suggestions?
Thanx
Thorsten
all from G3 to G5 Mac OS X (10.4.9)

I found an answer by myself.
Holding the power button after switching on brings you to the open firmware.
Now you can type:
reset-nvram [enter]
reset-all [enter]
After that the startup keys worked again.
Sometimes it's useful to refine your search

Start-up problem with the Z10

Can you assist us in a Start-up problem with the Z10's.
I have read a lot of complains with the Z10 starting-up and then got stuck at 98% completion. No further response after that!
For any further information please check the "BlackBerry Support Forum" on this same site.
Please respond or tel me who i can contact in this regard?
Thank you
Kobus69
Subject Title and beginning of post edited to reflect new topic.

Hi
Please find the link given below might help you to fix your issue.
Resolve Boot Device not Found Error Message
Let us know how it goes!
"I work for HP."
****Click the (purple thumbs up icon in the lower right corner of a post) to say thanks****
****Please mark Accept As Solution if it solves your problem****
Regards
Manjunath

PowerBook G4 Start-up problem

Start-up problem ---
1. When I recently ran OnyX, I was told to run the Apple’s Disk Utility from the Start-up Disk.
2. However, before doing this, I ran the Disk Utility from the hard drive, but the program would not complete the “Repair” function. It just got “stuck” and I had to stop the repair.
3. While running the Disk Utility from the Start-up disk, I got the following message: “Disk Utility has lost its connection with the Disk Management Tool and cannot continue. Please quit and re-launch Disk Utility.”
4. I did quit and re-launch Disk Utility but received the same error message.
5. Took PowerBook to Apple store and technicians ran diagnostics (for several days), couldn’t identify problem even though computer wouldn’t start after they ran full set of diagnostics.
6. I reinstalled the OS 10.5 from scratch, reformatting my hard drive. Then, I re-installed all programs and documents, etc. Seemed to work OK.
7. Tried to run OnyX, but the computer froze. Ran Disk Utility from the start-up driver and it repair hundreds of permissions as well as “repair disk” function (hundreds of items).
8. While the PowerBook is running OK right now, am concerned about possible hardware failure.
Any thoughts/ideas?
Thanks.

Download Smart Utility from http://www.volitans-software.com/smart_utility.php . It will enable you to see the values of the SMART sensors, and can give you insight into the health of the drive.
When you ran repair disk from the OS X DVD, did it complete normally? No 'failure on exit' message?

I got my iPhone 5 s almost a month ago and updated its iOS but from there on I started having problems, the ph sometimes doesn't respond at all to the touch or apps start to open on their own very rapidly and this continues till it can go no further!

I got my iPhone 5 almost a month ago and updated its iOS but from there on I started having problems, the ph sometimes doesn't respond at all to the touch or apps start to open on their own very rapidly and this continues till it can go no further!

First steps in troubleshooting:
Close all open apps by double-tapping the home button, then swiping up and off the screen with the app window (not the smaller icon).
Then reset: hold down the home button along with the sleep/wake button until you see the apple, then let go. (No data loss)

Shut down // start up problems

i am having power related problems on the intel mini and i want to know how widespread this is before i confront apple support. btw i love the mini--this is my 2nd mini. i have had a power on problem with a mini even on the day of purchase and it was exchanged graciously at the apple store in white plains this past july.<this was a power button failure issue>
here's whats happenning....1>it misbehaves on shut down or restart by software. there gets to a point where the screen is black but the white light on the box stays on and the vents in the back are still warm. my workaround is to manually shut down about a minute after the software shut down by holding down the power button on the back of the mini.
......2> start up problem. the mini wont always start when i push the power button. my workaround has been to turn off my surge protector for about 10 seconds then turn it back on and VIOLA the power button can start the mini. i guess it needs to be cold to work.
i have been reticent to go to the store because i rely on this machine too much and i am not the only user here.
can some reader disclose if such a hardware failure is known?
thanks in advance.

thanks. i hadn't thought about the surge protector.
keyboard and mouse are bluetooth.monitor is digital 24". i have an external powered usb hub which runs my time machine external drive. i keep everything else unplugged from the usb hub during startup and shutdown because my ipod shuffle caused startup problems in the past.
i had similar troubles with my first mini when it was plugged directly into a wall socket. the surge protector seems to help--at least i can cold start the mini without unplugging it.
i have a genius bar apptmt this evening and i will see what gives. i am glad i made apple put in their own overpriced ram so i never voided the warranty. maybe i will buy a care plan to cover myself when i am there. but i so want to raise this mini from 2 to 4 gig now that mem is so cheap. if i can get this problem stabilized...
my very first mini was powerpc and the ipod shuffle, according to genius bar, caused its demise due to usb 1.1 and usb2.0 handshaking problems. i still have it somewhere and plan to install a harddrive to get it going.
thanks again guys.
and i'd like to ask others again if this problem is more common.

New MB Pro; start-up problems (again)

In case you remember me, yes I am the same person who recently bought a MB Air and had lots of problems off the bat (some of which required repair by Apple). It is working fine now, but it was just not working out for my needs. So, I decided to suck it up, switch to the Pro and sell that Air.
Now the PRO is giving me start-up problems. Gah! I made a fresh Time Machine back-up from the Air...then used Time Machine upon initial set-up to transfer everything to my Pro (thinking I was wiser this time, doing it upon initial set-up). But...no go. First my Pro would not recognize my admin password and I had to reset that. Now that I'm into my system, iPhoto will not open (I get a window vaguely stating there is some problem that it then reports to Apple); Calendar and Notes just show big question marks in the dock.
I opened a new user account to see what would happen: in that account, Notes and calendar seem just fine, but iPhoto still will not open.
Furthermore, in my support research I keep coming across stuff that talks about the install disk....But never saw one! Am I supposed to have one, or are the new Pros like the Air (in having online reboot sytem)? I did not see any disks in my box (which of course is currently not where I can access it to double check). The only place the disk could have been is underneath the frame inside the box, but there is usually nothing under there, so I don't think I had one. Could this be right?
Other possibly useful (?) info: I bought the Pro w an 8GB RAM upgrade, which was installed right in store. When I opened a new user account I got a window talking about "automatic login" and how the computer would start to an account that was named after the store where I bought the computer if i did not turn it off. I did turn it off but I would like to get rid of this "store account"...but is not listed as a User acct so I don't know how to find it in order to get rid of it.
Help?!

Thanks for the input. I totally agree that I'd like to take this one back and exchange for a new one. Only problem is that I am traveling for work internationally until after the 14-day deadline. It's quite a hassle to get back to the US in time, though I have it in my back pocket to push for an extention to that time period...
Meanwhile, I had my 3rd Apple Support chat today. They finally gave me a dedicated Sr. Advisor who managed to get the Lion erase and install to take this time. (I didn't pay for the Mountain Lion upgrade; one thing having gone right!) I have to get green-lighted for another free Mountian Lion upgrade but at least we're on track at this point. Fingers crossed it continues that way!
At the rate they're going with me this summer, I should think a discounted AppleCare is in order or SOMETHING. Gah!
For any future problem-having readers, I'm afriad they did not seem to understand/answer why this was happening, so I've no wisdom to impart!
For the responders: Thanks again!

Satellite Pro M10 - start up problems

Hi
I have a Satellite Pro M10, only 2 years old, but has big start up problems at mement.
The message that comes up when turning it on is:
"Intel (R) Boot Agent FE v4.1.09
Copyright (C) 1997-2002, Intel Corporation
PXE-E61: Media test failure, check cable
PXE-MOF: Exiting Intel Boot Agent.
Insert system disk in drive.
press any key when ready......"
Now I have spoken to a few people and they all say I need a new hard disk etc..., but I can't see how you replace this as it looks like it is built in rather than something than can just be pulled out.
Also I don't have a system disk, and the guy that supplied it to me has decided not to return my emails?
Can anyone help please?
Chris

Hi,
Your original error messages indicate that your laptop is unable to boot from the hard drive, so the BIOS search order will then force a boot from the CD drive. This is why it is asking fro a disc to be inserted.
Since you cannot boot into safe mode then I must presume that your hard drive is corrupt in some way, so the next option is to restore the hard drive from your recovery CDs. Note that this will reformat you hard drive and you will lose any data on there which has not been backed up.
To use the recovery CDs simply insert the first CD into the CD drive and power attempt to reboot the laptop while holding down the 'C' key on the keyboard. (This may be different for your CDs but it is the "C" key on mine).
Then just follow the on-screen prompts to start restoring your hard drive.
With regard to your question about the 'system disk', this can be any bootable CD that you may have. Some can be supplied by third party products (such as Norton Ghost) or may be created yourself for subsequent use. Your product recovery CDs are also bootable so you may be able to user the first of them at this prompt.

Hi everyone. I have just started having problems with iCal. Events that I thought I had deleted are appearing on Print Preview and on print outs. Likewise Events which I have not deleted have disappeared from my calenders, but appear in print preview.

Hi everybody. I have recently started having problems with iCal (Version 2.05 (1069). Events that I thought I had deleted appear in Print Preview and Print Outs. Likewise Events that I have not deleted have disappeared from my calender (Month View) but appear in Print Preview and Print Outs. I see that there have been similar problems with Events disappearing especially in Month View. I wondered how print preview seemrd to be picking everything up deleted or not, and what the solution may be?. First time of Posting. I hope I haven't embarassed myself.

Hmmmm.
At the very least there must be a "com.apple.ical.plist"...iCal would not function without it.
Click on the Finder icon in the dock
Click on Go > Home
Double-click Library
Double-click Preferences
Look for a file called "com.apple.ical.plist" and remove it to the trash.

Intermittent start up problem

Similar Messages

Maybe you are looking for