Internal DHCP Server on Wireless not working

Hi community,
I'm facing some problems to setup a DHCP server on a WLC 2504. I'll try to resume my configuration:
I have 2 networks: inside users (vlan 1) and external users (vlan)
My controller uses the port 1 to connect to the switch, which has a trunk with WLC.
I have two routers, one using vlan 1 (192.168.3.0/24) and one using vlan 10 (200.X.X.X). All ports to these routers are access ports on their respective vlans.
I have 2 SSID, one for inside, other to outside. Inside is working very well.
To the outside I created a DHCP escope and already set the IP of the management interface 192.168.3.119.
Managemente interface (vlan 1 inside): 192.168.3.119/24
Outside interface (vlan 10): 200.X.X.195 - Default gateway 200.X.X.X.193
I alredy checked the DHCP Proxy in Advanced option.
See the output of the debug client:
(Cisco Controller) >
(Cisco Controller) >
(Cisco Controller) >
(Cisco Controller) >debug client 00:27:10:ce:38:e8
(Cisco Controller) >
(Cisco Controller) >
(Cisco Controller) >*apfMsConnTask_2: Mar 26 17:45:11.390: 00:27:10:ce:38:e8 Association received from mobile on AP a4:18:75:03:e0:c0
*apfMsConnTask_2: Mar 26 17:45:11.390: 00:27:10:ce:38:e8 Global 200 Clients are allowed to AP radio
*apfMsConnTask_2: Mar 26 17:45:11.390: 00:27:10:ce:38:e8 Max Client Trap Threshold: 0  cur: 1
*apfMsConnTask_2: Mar 26 17:45:11.390: 00:27:10:ce:38:e8 Applying Interface policy on Mobile, role Local. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 10
*apfMsConnTask_2: Mar 26 17:45:11.390: 00:27:10:ce:38:e8 Re-applying interface policy for client
*apfMsConnTask_2: Mar 26 17:45:11.390: 00:27:10:ce:38:e8 192.168.3.206 RUN (20) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1851)
*apfMsConnTask_2: Mar 26 17:45:11.390: 00:27:10:ce:38:e8 192.168.3.206 RUN (20) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2018)
*apfMsConnTask_2: Mar 26 17:45:11.390: 00:27:10:ce:38:e8 In processSsidIE:3883 setting Central switched to TRUE
*apfMsConnTask_2: Mar 26 17:45:11.390: 00:27:10:ce:38:e8 In processSsidIE:3886 apVapId = 2 and Split Acl Id = 65535
*apfMsConnTask_2: Mar 26 17:45:11.390: 00:27:10:ce:38:e8 Applying site-specific Local Bridging override for station 00:27:10:ce:38:e8 - vapId 2, site 'default-group', interface 'externo-embratel'
*apfMsConnTask_2: Mar 26 17:45:11.390: 00:27:10:ce:38:e8 Applying Local Bridging Interface Policy for station 00:27:10:ce:38:e8 - vlan 10, interface id 12, interface 'externo-embratel'
*apfMsConnTask_2: Mar 26 17:45:11.390: 00:27:10:ce:38:e8 processSsidIE  statusCode is 0 and status is 0
*apfMsConnTask_2: Mar 26 17:45:11.390: 00:27:10:ce:38:e8 processSsidIE  ssid_done_flag is 0 finish_flag is 0
*apfMsConnTask_2: Mar 26 17:45:11.390: 00:27:10:ce:38:e8 STA - rates (8): 140 18 152 36 176 72 96 108 48 72 96 108 0 0 0 0
*apfMsConnTask_2: Mar 26 17:45:11.390: 00:27:10:ce:38:e8 suppRates  statusCode is 0 and gotSuppRatesElement is 1
*apfMsConnTask_2: Mar 26 17:45:11.390: 00:27:10:ce:38:e8 Processing RSN IE type 48, length 22 for mobile 00:27:10:ce:38:e8
*apfMsConnTask_2: Mar 26 17:45:11.390: 00:27:10:ce:38:e8 apfMsRunStateDec
*apfMsConnTask_2: Mar 26 17:45:11.390: 00:27:10:ce:38:e8 apfMs1xStateDec
*apfMsConnTask_2: Mar 26 17:45:11.390: 00:27:10:ce:38:e8 192.168.3.206 RUN (20) Change state to START (0) last state RUN (20)
*apfMsConnTask_2: Mar 26 17:45:11.390: 00:27:10:ce:38:e8 pemApfAddMobileStation2: APF_MS_PEM_WAIT_L2_AUTH_COMPLETE = 0.
*apfMsConnTask_2: Mar 26 17:45:11.390: 00:27:10:ce:38:e8 192.168.3.206 START (0) Initializing policy
*apfMsConnTask_2: Mar 26 17:45:11.390: 00:27:10:ce:38:e8 192.168.3.206 START (0) Change state to AUTHCHECK (2) last state START (0)
*apfMsConnTask_2: Mar 26 17:45:11.390: 00:27:10:ce:38:e8 192.168.3.206 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
*apfMsConnTask_2: Mar 26 17:45:11.391: 00:27:10:ce:38:e8 Not Using WMM Compliance code qosCap 00
*apfMsConnTask_2: Mar 26 17:45:11.391: 00:27:10:ce:38:e8 192.168.3.206 8021X_REQD (3) Plumbed mobile LWAPP rule on AP a4:18:75:03:e0:c0 vapId 2 apVapId 2 flex-acl-name:
*apfMsConnTask_2: Mar 26 17:45:11.391: 00:27:10:ce:38:e8 apfPemAddUser2 (apf_policy.c:273) Changing state for mobile 00:27:10:ce:38:e8 on AP a4:18:75:03:e0:c0 from Associated to Associated
*apfMsConnTask_2: Mar 26 17:45:11.391: 00:27:10:ce:38:e8 Scheduling deletion of Mobile Station:  (callerId: 49) in 1800 seconds
*apfMsConnTask_2: Mar 26 17:45:11.391: 00:27:10:ce:38:e8 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 1800
*apfMsConnTask_2: Mar 26 17:45:11.391: 00:27:10:ce:38:e8 Sending Assoc Response to station on BSSID a4:18:75:03:e0:c0 (status 0) ApVapId 2 Slot 1
*apfMsConnTask_2: Mar 26 17:45:11.391: 00:27:10:ce:38:e8 apfProcessAssocReq (apf_80211.c:6719) Changing state for mobile 00:27:10:ce:38:e8 on AP a4:18:75:03:e0:c0 from Associated to Associated
*pemReceiveTask: Mar 26 17:45:11.393: 00:27:10:ce:38:e8 192.168.3.206 Removed NPU entry.
*dot1xMsgTask: Mar 26 17:45:11.394: 00:27:10:ce:38:e8 Creating a PKC PMKID Cache entry for station 00:27:10:ce:38:e8 (RSN 2)
*dot1xMsgTask: Mar 26 17:45:11.394: 00:27:10:ce:38:e8 Resetting MSCB PMK Cache Entry 0 for station 00:27:10:ce:38:e8
*dot1xMsgTask: Mar 26 17:45:11.394: 00:27:10:ce:38:e8 Setting active key cache index 8 ---> 8
*dot1xMsgTask: Mar 26 17:45:11.394: 00:27:10:ce:38:e8 Setting active key cache index 8 ---> 0
*dot1xMsgTask: Mar 26 17:45:11.394: 00:27:10:ce:38:e8 Adding BSSID a4:18:75:03:e0:ce to PMKID cache at index 0 for station 00:27:10:ce:38:e8
*dot1xMsgTask: Mar 26 17:45:11.394: New PMKID: (16)
*dot1xMsgTask: Mar 26 17:45:11.394:      [0000] 61 96 e0 14 b9 0c c9 ca b2 e0 b7 0a 63 83 15 0d
*dot1xMsgTask: Mar 26 17:45:11.394: 00:27:10:ce:38:e8 Initiating RSN PSK to mobile 00:27:10:ce:38:e8
*dot1xMsgTask: Mar 26 17:45:11.394: 00:27:10:ce:38:e8 dot1x - moving mobile 00:27:10:ce:38:e8 into Force Auth state
*dot1xMsgTask: Mar 26 17:45:11.394: 00:27:10:ce:38:e8 Skipping EAP-Success to mobile 00:27:10:ce:38:e8
*dot1xMsgTask: Mar 26 17:45:11.394: 00:27:10:ce:38:e8 Found an cache entry for BSSID a4:18:75:03:e0:ce in PMKID cache at index 0 of station 00:27:10:ce:38:e8
*dot1xMsgTask: Mar 26 17:45:11.394: 00:27:10:ce:38:e8 Found an cache entry for BSSID a4:18:75:03:e0:ce in PMKID cache at index 0 of station 00:27:10:ce:38:e8
*dot1xMsgTask: Mar 26 17:45:11.394: Including PMKID in M1  (16)
*dot1xMsgTask: Mar 26 17:45:11.394:      [0000] 61 96 e0 14 b9 0c c9 ca b2 e0 b7 0a 63 83 15 0d
*dot1xMsgTask: Mar 26 17:45:11.394: 00:27:10:ce:38:e8 Starting key exchange to mobile 00:27:10:ce:38:e8, data packets will be dropped
*dot1xMsgTask: Mar 26 17:45:11.394: 00:27:10:ce:38:e8 Sending EAPOL-Key Message to mobile 00:27:10:ce:38:e8
                                                                                                              state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_0: Mar 26 17:45:11.396: 00:27:10:ce:38:e8 Received EAPOL-Key from mobile 00:27:10:ce:38:e8
*Dot1x_NW_MsgTask_0: Mar 26 17:45:11.396: 00:27:10:ce:38:e8 Ignoring invalid EAPOL version (1) in EAPOL-key message from mobile 00:27:10:ce:38:e8
*Dot1x_NW_MsgTask_0: Mar 26 17:45:11.397: 00:27:10:ce:38:e8 Received EAPOL-key in PTK_START state (message 2) from mobile 00:27:10:ce:38:e8
*Dot1x_NW_MsgTask_0: Mar 26 17:45:11.397: 00:27:10:ce:38:e8 Stopping retransmission timer for mobile 00:27:10:ce:38:e8
*Dot1x_NW_MsgTask_0: Mar 26 17:45:11.397: 00:27:10:ce:38:e8 Sending EAPOL-Key Message to mobile 00:27:10:ce:38:e8
                                                                                                                    state PTKINITNEGOTIATING (message 3), replay counter 00.00.00.00.00.00.00.01
*Dot1x_NW_MsgTask_0: Mar 26 17:45:11.399: 00:27:10:ce:38:e8 Received EAPOL-Key from mobile 00:27:10:ce:38:e8
*Dot1x_NW_MsgTask_0: Mar 26 17:45:11.399: 00:27:10:ce:38:e8 Ignoring invalid EAPOL version (1) in EAPOL-key message from mobile 00:27:10:ce:38:e8
*Dot1x_NW_MsgTask_0: Mar 26 17:45:11.399: 00:27:10:ce:38:e8 Received EAPOL-key in PTKINITNEGOTIATING state (message 4) from mobile 00:27:10:ce:38:e8
*Dot1x_NW_MsgTask_0: Mar 26 17:45:11.399: 00:27:10:ce:38:e8 Stopping retransmission timer for mobile 00:27:10:ce:38:e8
*Dot1x_NW_MsgTask_0: Mar 26 17:45:11.399: 00:27:10:ce:38:e8 apfMs1xStateInc
*Dot1x_NW_MsgTask_0: Mar 26 17:45:11.400: 00:27:10:ce:38:e8 192.168.3.206 8021X_REQD (3) Change state to L2AUTHCOMPLETE (4) last state 8021X_REQD (3)
*Dot1x_NW_MsgTask_0: Mar 26 17:45:11.400: 00:27:10:ce:38:e8 Not Using WMM Compliance code qosCap 00
*Dot1x_NW_MsgTask_0: Mar 26 17:45:11.400: 00:27:10:ce:38:e8 192.168.3.206 L2AUTHCOMPLETE (4) Plumbed mobile LWAPP rule on AP a4:18:75:03:e0:c0 vapId 2 apVapId 2 flex-acl-name:
*Dot1x_NW_MsgTask_0: Mar 26 17:45:11.400: 00:27:10:ce:38:e8 apfMsRunStateInc
*Dot1x_NW_MsgTask_0: Mar 26 17:45:11.400: 00:27:10:ce:38:e8 192.168.3.206 L2AUTHCOMPLETE (4) Change state to RUN (20) last state L2AUTHCOMPLETE (4)
*Dot1x_NW_MsgTask_0: Mar 26 17:45:11.400: 00:27:10:ce:38:e8 192.168.3.206 RUN (20) Reached PLUMBFASTPATH: from line 5982
*Dot1x_NW_MsgTask_0: Mar 26 17:45:11.400: 00:27:10:ce:38:e8 192.168.3.206 RUN (20) Adding Fast Path rule
  type = Airespace AP Client
  on AP a4:18:75:03:e0:c0, slot 1, interface = 1, QOS = 0
  IPv4 ACL ID = 255, IPv6 ACL ID =
*Dot1x_NW_MsgTask_0: Mar 26 17:45:11.400: 00:27:10:ce:38:e8 192.168.3.206 RUN (20) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 15206  Local Bridging Vlan = 10, Local Bridging intf id = 12
*Dot1x_NW_MsgTask_0: Mar 26 17:45:11.400: 00:27:10:ce:38:e8 192.168.3.206 RUN (20) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255)
*pemReceiveTask: Mar 26 17:45:11.400: 00:27:10:ce:38:e8 192.168.3.206 Added NPU entry of type 1, dtlFlags 0x0
*pemReceiveTask: Mar 26 17:45:11.401: 00:27:10:ce:38:e8 Pushing IPv6: fe80:0000:0000:0000: 893c:4ed3:f9a0:b90f , and MAC: 00:27:10:CE:38:E8 , Binding to Data Plane. SUCCESS !!
*DHCP Socket Task: Mar 26 17:45:11.445: 00:27:10:ce:38:e8 DHCP received op BOOTREQUEST (1) (len 331,vlan 0, port 1, encap 0xec03)
*DHCP Socket Task: Mar 26 17:45:11.445: 00:27:10:ce:38:e8 DHCP selecting relay 1 - control block settings:
                        dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
                        dhcpGateway: 0.0.0.0, dhcpRelay: 200.x.x..195  VLAN: 10
*DHCP Socket Task: Mar 26 17:45:11.445: 00:27:10:ce:38:e8 DHCP selected relay 1 - 192.168.3.119 (local address 200.x.x.195, gateway 200.x.x.193, VLAN 10, port 1)
*DHCP Socket Task: Mar 26 17:45:11.445: 00:27:10:ce:38:e8 DHCP transmitting DHCP REQUEST (3)
*DHCP Socket Task: Mar 26 17:45:11.445: 00:27:10:ce:38:e8 DHCP   op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 1
*DHCP Socket Task: Mar 26 17:45:11.445: 00:27:10:ce:38:e8 DHCP   xid: 0x464542f7 (1178944247), secs: 0, flags: 8000
*DHCP Socket Task: Mar 26 17:45:11.445: 00:27:10:ce:38:e8 DHCP   chaddr: 00:27:10:ce:38:e8
*DHCP Socket Task: Mar 26 17:45:11.445: 00:27:10:ce:38:e8 DHCP   ciaddr: 0.0.0.0,  yiaddr: 0.0.0.0
*DHCP Socket Task: Mar 26 17:45:11.445: 00:27:10:ce:38:e8 DHCP   siaddr: 0.0.0.0,  giaddr: 200.x.x.195
*DHCP Socket Task: Mar 26 17:45:11.445: 00:27:10:ce:38:e8 DHCP   requested ip: 192.168.3.206
*DHCP Socket Task: Mar 26 17:45:11.445: 00:27:10:ce:38:e8 DHCP selecting relay 2 - control block settings:
                        dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
                        dhcpGateway: 0.0.0.0, dhcpRelay: 200.x.x.195  VLAN: 10
*DHCP Socket Task: Mar 26 17:45:11.445: 00:27:10:ce:38:e8 DHCP selected relay 2 - NONE
*DHCP Socket Task: Mar 26 17:45:14.647: 00:27:10:ce:38:e8 DHCP received op BOOTREQUEST (1) (len 331,vlan 0, port 1, encap 0xec03)
*DHCP Socket Task: Mar 26 17:45:14.647: 00:27:10:ce:38:e8 DHCP selecting relay 1 - control block settings:
                        dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
                        dhcpGateway: 0.0.0.0, dhcpRelay: 200.x.x.195  VLAN: 10
*DHCP Socket Task: Mar 26 17:45:14.647: 00:27:10:ce:38:e8 DHCP selected relay 1 - 192.168.3.119 (local address 200.x.x.195, gateway 200.x.x.193, VLAN 10, port 1)
*DHCP Socket Task: Mar 26 17:45:14.647: 00:27:10:ce:38:e8 DHCP transmitting DHCP REQUEST (3)
*DHCP Socket Task: Mar 26 17:45:14.647: 00:27:10:ce:38:e8 DHCP   op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 1
*DHCP Socket Task: Mar 26 17:45:14.647: 00:27:10:ce:38:e8 DHCP   xid: 0x464542f7 (1178944247), secs: 768, flags: 8000
*DHCP Socket Task: Mar 26 17:45:14.647: 00:27:10:ce:38:e8 DHCP   chaddr: 00:27:10:ce:38:e8
*DHCP Socket Task: Mar 26 17:45:14.647: 00:27:10:ce:38:e8 DHCP   ciaddr: 0.0.0.0,  yiaddr: 0.0.0.0
*DHCP Socket Task: Mar 26 17:45:14.647: 00:27:10:ce:38:e8 DHCP   siaddr: 0.0.0.0,  giaddr: 200.x.x.195
*DHCP Socket Task: Mar 26 17:45:14.647: 00:27:10:ce:38:e8 DHCP   requested ip: 192.168.3.206
*DHCP Socket Task: Mar 26 17:45:14.647: 00:27:10:ce:38:e8 DHCP selecting relay 2 - control block settings:
                        dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
                        dhcpGateway: 0.0.0.0, dhcpRelay: 200.x.x.195  VLAN: 10
*DHCP Socket Task: Mar 26 17:45:14.647: 00:27:10:ce:38:e8 DHCP selected relay 2 - NONE
*DHCP Socket Task: Mar 26 17:45:23.590: 00:27:10:ce:38:e8 DHCP received op BOOTREQUEST (1) (len 331,vlan 0, port 1, encap 0xec03)
*DHCP Socket Task: Mar 26 17:45:23.590: 00:27:10:ce:38:e8 DHCP selecting relay 1 - control block settings:
                        dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
                        dhcpGateway: 0.0.0.0, dhcpRelay: 200.x.x.195  VLAN: 10
*DHCP Socket Task: Mar 26 17:45:23.590: 00:27:10:ce:38:e8 DHCP selected relay 1 - 192.168.3.119 (local address 200.x.x.195, gateway 200.x.x.193, VLAN 10, port 1)
*DHCP Socket Task: Mar 26 17:45:23.590: 00:27:10:ce:38:e8 DHCP transmitting DHCP REQUEST (3)
*DHCP Socket Task: Mar 26 17:45:23.590: 00:27:10:ce:38:e8 DHCP   op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 1
*DHCP Socket Task: Mar 26 17:45:23.590: 00:27:10:ce:38:e8 DHCP   xid: 0x464542f7 (1178944247), secs: 3072, flags: 8000
*DHCP Socket Task: Mar 26 17:45:23.590: 00:27:10:ce:38:e8 DHCP   chaddr: 00:27:10:ce:38:e8
*DHCP Socket Task: Mar 26 17:45:23.590: 00:27:10:ce:38:e8 DHCP   ciaddr: 0.0.0.0,  yiaddr: 0.0.0.0
*DHCP Socket Task: Mar 26 17:45:23.590: 00:27:10:ce:38:e8 DHCP   siaddr: 0.0.0.0,  giaddr: 200.x.x.195
*DHCP Socket Task: Mar 26 17:45:23.590: 00:27:10:ce:38:e8 DHCP   requested ip: 192.168.3.206
*DHCP Socket Task: Mar 26 17:45:23.590: 00:27:10:ce:38:e8 DHCP selecting relay 2 - control block settings:
                        dhcpServer: 0.0.0.0, dhcpNetmask: 0.0.0.0,
                        dhcpGateway: 0.0.0.0, dhcpRelay: 200.x.x.195  VLAN: 10
*DHCP Socket Task: Mar 26 17:45:23.590: 00:27:10:ce:38:e8 DHCP selected relay 2 - NONE
(Cisco Controller) >
What can be wrong?
Thank you in advanced.

Hi Plinio,
I see your device connected twice. it connected to the first SSID successfully and I can see it got IP 192.168.3.206.
Then it tries to get an ip from the other scope!! (while as the debugs show it is already connected and in RUN state).
That is strange!!
a question: do you have DHCP required enabled under your WLAN?
Rating useful replies is more useful than saying "Thank you"

Similar Messages

  • WLC CT2504: Interface IP can not be used as internal DHCP server IP

    Hello all,
    I've got a new CT2504 controller with software version 7.0.220.0
    Regarding to
    http://www.cisco.com/en/US/products/ps6366/products_tech_note09186a0080af5d13.shtml
    I've tried to configure the internal DHCP on a dynamic-interface, but this is not possible:
    (Cisco Controller) >config interface dhcp dynamic-interface vlan401 primary 172.16.x.3
    vlan401 Interface IP can not be used as internal DHCP server IP
    It works, if I use another IP (aka DHCP server) in the same subnet or in another subnet. It works also for the management interface.
    (Cisco Controller) >show interface detailed management
    Interface Name................................... management
    MAC Address...................................... d0:c2:82:xx:xx:xx
    IP Address....................................... 10.2.x.135
    IP Netmask....................................... 255.255.255.240
    IP Gateway....................................... 10.2.x.129
    External NAT IP State............................ Disabled
    External NAT IP Address.......................... 0.0.0.0
    VLAN............................................. 400
    Quarantine-vlan.................................. 0
    Active Physical Port............................. 1
    Primary Physical Port............................ 1
    Backup Physical Port............................. Unconfigured
    Primary DHCP Server.............................. 10.2.x.135
    Secondary DHCP Server............................ Unconfigured
    DHCP Option 82................................... Disabled
    ACL.............................................. Unconfigured
    AP Manager....................................... Yes
    Guest Interface.................................. No
    L2 Multicast..................................... Disabled
    Scopes are defined and Proxy is enabled.
    (Cisco Controller) >show dhcp summary
      Scope Name                   Enabled          Address Range
    ap                               Yes      10.2.x.137 -> 10.2.x.140
    intern                            Yes      172.16.x.20 -> 172.16.x.30
    (Cisco Controller) >show dhcp proxy
    DHCP Proxy Behaviour: enabled
    Has somebody an explanation for this issue?
    Thanks in advance,
    Regard,
    Robert

    You can use the internal dhcp, but you need to set the primary dhcp as the management ip. So in your dynamic interface, your primary dhcp is configure with the wlc management ip address. Dhcp proxy also needs to be enabled and is enabled by default.
    Thanks,
    Scott Fella
    Sent from my iPhone

  • WLC 5508 Internal DHCP server issues

    Hi,
    I am hoping to get your feedback around the dhcp issues I am facing with Two Centrally Switched Wireless LANs. I have tried to explain the setup and the problems below and would appreciate it if anyone can suggest a solution for the problems I am facing:
    The setup is as follows:
    - I have a WLC 5508 which has been configured with 4 SSIDs, out of which 2 are using Central Authentication and Switching.
    - I have an LWAP connected to the WLC in HREAP mode.
    - WLC is configured as the DHCP server for clients connecting to the SSID 'Guest'. For the rest, I am using external dhcp server.
    - Only one scope for Guest Interface is setup on the WLC. 
    Problems:
    1. As far as I know, for WLC to act as internal dhcp server, it is mandatory to have the proxy enabled, but the Clients connecting to SSID 'Internet' are
    unable to get an ip address from the external dhcp server, if dhcp proxy is enabled on the WLC. If i disable the proxy, it all works fine.
    2. DHCP does not release the ip addresses assigned to clients even after they are logged out.
    3. If a machine which was earlier connected to 'Guest' SSID connects to the 'Internet' SSID, it requests the same ip it was assigned by the WLC which it was assigned under 'Guest', but gets tagged with the Vlan configured on the management interface.  
    ************Output from the Controller********************
    (Cisco Controller) >show sysinfo
    Manufacturer's Name.............................. Cisco Systems Inc.
    Product Name..................................... Cisco Controller
    Product Version.................................. 7.0.116.0
    Bootloader Version............................... 1.0.1
    Field Recovery Image Version..................... 6.0.182.0
    Firmware Version................................. FPGA 1.3, Env 1.6, USB console 1.27
    Build Type....................................... DATA + WPS + LDPE
    (Cisco Controller) >show interface summary
    Interface Name                   Port Vlan Id  IP Address         Type        Ap Mgr        Gu                                                                            
    est
    guest                                        1    301      10.255.255.30    Dynamic   No              No                                                                            
    management                          1    100      172.17.1.30        Static          Yes            No                                                          
    service-port                              N/A  N/A      192.168.0.1       Static         No               No                                                                            
    virtual                                        N/A   N/A      10.0.0.1              Static         No               No                                                                            
    (Cisco Controller) >show wlan summary
    Number of WLANs.................................. 4
    WLAN ID  WLAN Profile Name / SSID               Status    Interface Name
    1        LAN                                    Enabled   management
    2        Internet                               Enabled   management
    3        Managment Assets          Enabled   management
    4        Guest                                  Enabled   guest
    (Cisco Controller) >show dhcp detailed guest
    Scope: guest
    Enabled.......................................... Yes
    Lease Time....................................... 86400 (1 day )
    Pool Start....................................... 10.255.255.31
    Pool End......................................... 10.255.255.254
    Network.......................................... 10.255.255.0
    Netmask.......................................... 255.255.255.0
    Default Routers.................................. 10.255.255.1  0.0.0.0  0.0.0.0
    DNS Domain.......................................
    DNS.............................................. 8.8.8.8  8.8.4.4  0.0.0.0
    Netbios Name Servers............................. 0.0.0.0  0.0.0.0  0.0.0.0
    (Cisco Controller) >show interface detailed management
    Interface Name................................... management
    MAC Address...................................... e8:b7:48:9b:84:20
    IP Address....................................... 172.17.1.30
    IP Netmask....................................... 255.255.255.0
    IP Gateway....................................... 172.17.1.1
    External NAT IP State............................ Disabled
    External NAT IP Address.......................... 0.0.0.0
    VLAN............................................. 100
    Quarantine-vlan.................................. 0
    Active Physical Port............................. 1
    Primary Physical Port............................ 1
    Backup Physical Port............................. Unconfigured
    Primary DHCP Server.............................. 172.30.50.1
    Secondary DHCP Server............................ Unconfigured
    DHCP Option 82................................... Disabled
    ACL.............................................. Unconfigured
    AP Manager....................................... Yes
    Guest Interface.................................. No
    L2 Multicast..................................... Enabled
    (Cisco Controller) >show interface detailed guest
    Interface Name................................... guest
    MAC Address...................................... e8:b7:48:9b:84:24
    IP Address....................................... 10.255.255.30
    IP Netmask....................................... 255.255.255.0
    IP Gateway....................................... 10.255.255.1
    External NAT IP State............................ Disabled
    External NAT IP Address.......................... 0.0.0.0
    VLAN............................................. 301
    Quarantine-vlan.................................. 0
    Active Physical Port............................. 1
    Primary Physical Port............................ 1
    Backup Physical Port............................. Unconfigured
    Primary DHCP Server.............................. Unconfigured
    Secondary DHCP Server............................ Unconfigured
    DHCP Option 82................................... Disabled
    ACL.............................................. Unconfigured
    AP Manager....................................... No
    Guest Interface.................................. No
    L2 Multicast..................................... Enabled
    (Cisco Controller) >show dhcp leases
           MAC                IP         Lease Time Remaining
    00:21:6a:9c:03:04    10.255.255.46    23 hours 52 minutes 42 seconds        <<<<<<< lease remains even when the client is disconnected.
    *********Example of Client connected to the right Vlan with an ip address from the incorrect interface. *************
    (Cisco Controller) >show client detail 00:21:6a:9c:03:04
    Client MAC Address............................... 00:21:6a:9c:03:04
    Client Username ................................. N/A
    AP MAC Address................................... a0:cf:5b:00:49:c0
    AP Name.......................................... mel
    Client State..................................... Associated
    Client NAC OOB State............................. Access
    Wireless LAN Id.................................. 2                 <<<<<<<<   'Internet' SSID
    BSSID............................................ a0:cf:5b:00:49:ce
    Connected For ................................... 319 secs
    Channel.......................................... 36
    IP Address....................................... 10.255.255.46      <<<<<<< IP address assigned from the 'Guest' Interface or dhcp scope on the WLC
    Association Id................................... 1
    Authentication Algorithm......................... Open System
    Reason Code...................................... 1
    Status Code...................................... 0
    Session Timeout.................................. 1800
    Client CCX version............................... 4
    Client E2E version............................... 1
    QoS Level........................................ Silver
    802.1P Priority Tag.............................. disabled
    WMM Support...................................... Enabled
    Power Save....................................... OFF
    Mobility State................................... Local
    Mobility Move Count.............................. 0
    Security Policy Completed........................ Yes
    Policy Manager State............................. RUN
    Policy Manager Rule Created...................... Yes
    ACL Name......................................... none
    ACL Applied Status............................... Unavailable
    Policy Type...................................... N/A
    Encryption Cipher................................ None
    Management Frame Protection...................... No
    EAP Type......................................... Unknown
    H-REAP Data Switching............................ Central       <<<<<<<<<
    H-REAP Authentication............................ Central       <<<<<<<<<<
    Interface........................................ management
    VLAN............................................. 100           <<<<<<<<<<< right Vlan
    Quarantine VLAN.................................. 0
    Access VLAN...................................... 100

    Hi All,
    I have a similar issue where Wireless clients are not receiving automatic addressing from an internal DHCP server. I have multiple interfaces configured on the WLC which are connected to separate VLANS. The manually specified DHCP primary server entry is the same on all interfaces. Some clients are able to authenticate and receive automatic IP configuration but some clients are failing the address assignment process. I have checked connectivity between the WLC and DHCP server, this is confirmed as working. When I carry out a "debug dhcp packet enable", I get the following outputs which seems as if the DHCP discover request from the client is skipped. Your thoughts and inputs on this are appreciated.
    DHCP Socket Task: Nov 07 11:16:09.174: 00:22:fb:7b:37:32 DHCP option len (including the magic cookie) 76
    *DHCP Socket Task: Nov 07 11:16:09.174: 00:22:fb:7b:37:32 DHCP option: message type = DHCP DISCOVER
    *DHCP Socket Task: Nov 07 11:16:09.174: 00:22:fb:7b:37:32 DHCP option: 116 (len 1) - skipping
    *DHCP Socket Task: Nov 07 11:16:09.174: 00:22:fb:7b:37:32 DHCP option: 61 (len 7) - skipping
    *DHCP Socket Task: Nov 07 11:16:09.174: 00:22:fb:7b:37:32 DHCP option: requested ip = 169.254.223.5
    *DHCP Socket Task: Nov 07 11:16:09.174: 00:22:fb:7b:37:32 DHCP option: 12 (len 13) - skipping
    *DHCP Socket Task: Nov 07 11:16:09.174: 00:22:fb:7b:37:32 DHCP option: vendor class id = MSFT 5.0 (len 8)
    *DHCP Socket Task: Nov 07 11:16:09.174: 00:22:fb:7b:37:32 DHCP option: 55 (len 11) - skipping
    *DHCP Socket Task: Nov 07 11:16:09.174: 00:22:fb:7b:37:32 DHCP option: 43 (len 2) - skipping
    *DHCP Socket Task: Nov 07 11:16:09.174: 00:22:fb:7b:37:32 DHCP options end, len 76, actual 68
    *DHCP Socket Task: Nov 07 11:16:09.174: 00:22:fb:7b:37:32 DHCP Forwarding DHCP packet (332 octets) packet DHCP Socket Task: Nov 07 11:16:09.174: 00:22:fb:7b:37:32 DHCP option len (including the magic cookie) 76
    Thanks,
    Raj Sandhu

  • 5508 internal DHCP server

    Hi,
    A client wants us to use the internal DHCP server on a 5508 instead of Windows DHCP. They will have 15 APs initially and upto 25 later. The docs on the 7.2 WLC make it sound like this is discouraged:
    Internal DHCP ServerThe controllers contain an internal DHCP server. This server is typically used in branch offices that do not already have a DHCP server. The wireless network generally contains 10 access points or fewer, with the access points on the same IP subnet as the controller.
    In this case, the APs will not be in the same subnet as the Managment Internet.
    Is it a mistake to use the internal DHCP with upto 25 APs (3 WLANs)? 
    Thanks.

    #DHCP proxy needs to be enabled to use internal dhcp on WLC. WLC uses virtual ip for dhcp and they're unicast. So keeping the AP on L3 doesn't work with internal dhcp. dhcp for wireless client works due to the packets are sent to WLC via capwap.
    #The DHCP required state can cause traffic to not be forwarded properly if a client is deauthenticated or removed. To overcome this problem, ensure that the DHCP required state is always disabled.
    Ans: it is expected behavior irrespective of dhcp being internal or external, it is a feature and not disadvantage.
    Cons:-
    #can't have dhcp reservations.
    #can't have option 43 or any other dhcp options.
    #DHCP service can't be restarted, WLC reboot is required if needed to so.
    #If Multiple WLCs used, need to create non overlapping scope on other WLCs as well.
    #Wired clients cannot get ip from internal dhcp. So need to maintain separate network & dhcp server for wired network, and this require routing.
    #From WLC GUI, Can't remove the client, need to use cli.
    #WLC reboot may clear the dhcp lease, though not sure 100%

  • Cisco 1702i WAP: how to get an interface in a non-native bridge group/ VLAN to be recognized by the internal DHCP server

    Does anyone know how the internal DHCP server in these access points connects to virtual interfaces and bridges in the unit?
    Is there some sort of default connection that connects the DHCP server to the native bridge group or VLAN?
    In a test case, with an SSID in the native VLAN and bridge group, the 1702i serves an IP address to a wireless client no problem. But with a second SSID in a non native VLAN and bridge group, no IP gets served. My only guess is that since the bvi1 defaults to the native bridge group and VLAN, sub-interfaces also in this group are assumed to be in the same subnet as bvi1, or in this case:
    interface bvi1
      ip address 192.168.1.205 255.255.255.0
      no ip route-cache
      exit
    It would be the ..1. subnet.
    Since the dhcp pool is set as:
    ip dhcp pool GeneralWiFi
      network 192.168.1.0 255.255.255.0
      lease 1
      default-router 192.168.1.1
      dns-server 8.8.8.8
      exit
    There may be an assumption that anything bvi1 can talk to is in the ..1. subnet, so the above pool gets activated on a request coming through bvi1.
    Is the DHCP server just hanging out waiting for a request from an "area" that is assumed to be on the same subnet as the given pool?
    Do I need to somehow show the device what subnet the 2nd SSID/ subinterfaces are in so the internal DHCP server can decide it needs to go to work, or is there some sort of bridging between the DHCP server and the interfaces that needs to be done? I am trying to use the same DHCP pool for the second subnet at this point, since I assume I will need another router to service an additional subnet and DHCP pool.

    Keep in mind that DHCP is a broadcast packet to start. So the AP can only listen in the subnet that it has an IP address for.
    Now, for any other subnet you can use the AP for DHCP but you have to have an IP helper address on your L3 pointing back to the AP.
    That being said, I wouldn't use the DHCP server on the AP as it is limited. You'd be better off using a Microsoft server or some other device that is designed for DHCP.
    HTH,
    Steve

  • 5500 Series WLC internal DHCP Server - Exclusion?

    Hi there,
    We're using the internal DHCP server on our 5500 Series WLC which works fine.
    However on one WLAN we ran out of addresses so changed the subnet from a /25 to a /24.
    The problem is that the router/gateway is still in the middle (124/125/126) and not easily changed.
    I've moved the WLC interface to the top of the subnet (251) but the router is more difficult as its externally managed/controlled.
    So is there a way we can create a DHCP pool of .1 through 250 on a /24 mask but exclude 124/125/126?
    Thanks
    Mike
    PS - Router subnet masks were changed so can see whole subnet.

    Mike,
        The WLC isn't a fully functional DHCP server, it only allows you to define what is in scope, not what is out of scope.  Now if you have a cisco router/switch, you could use that for the DHCP server and specifically exclude the necessary addresses.
    HTH,
    Steve

  • Lion Server DNS service not working for locally created zones. Caching working fine.

    OS Lion Server DNS service not working for local zones. Was fine under Snow leopard server but Lion server upgrade has severely broken my DNS and web sites. Zones look fine under Server Admin but keep getting "query failed (SERVFAIL) for xxxx at /SourceCache/bind9/bind9-42/bind9/bin/named/query.c:3921" in the logs. BTW - Server Admin cant seem to see the log file either.
    Surely someone actually tested that DNS still worked on Lion?

    I upgraded from Snow Leopard Server to Lion Server on day 01.  I hit the same issue where, after the upgrade, my Lion Server stopped serving names for my private local domain.
    I finally took a few minutes to figure out what was wrong.  After turning on debug logging and looking through the logs, I found my particular issue, now resolved.
    The issue I had was, when the domain initially was setup when I installed Snow Leopard Server, for some reason it created a zone just for the server (in my case, something like zone "s-01.mydomain.priv"), and a separate zone for all the other machines (zone "mydomain.priv", containing all the private IPs for my local domain).  I never messed with it because it worked, but generally I would have put all of them in the same zone.
    My zone "mydomain.priv" had a nameserver and mail exchanger entry for my server, s-01.mydomain.priv.  I could see this in the Server Admin app on the DNS bubble, Zones tab, mydomain.priv selected, and the General Info panel.  This was fine in Snow Leopard.  This was failing the zone load in the updated bind for Lion Server, though.  The issue was that the "mydomain.priv" zone was referencing the s-01.mydomain.priv server, which was not defined in the "mydomain.priv" zone but rather in the "s-01.mydomain.priv" zone.
    My fix:
    1. In Server Admin, add the server to the zone "mydomain.priv".  I put an A record (Add Machine) in the "mydomain.priv" zone for my server named s-01.mydomain.priv.
    2. shut down DNS on the OS X Lion Server (hit the Stop DNS button on Server Admin).
    3. edit /etc/named.conf by hand, removing the specialized zones that contianed just the server.  In this case, it would be the section titled 'zone "s-01.mydomain.priv"' and the section titled 'zone "3.10.1.10.in-addr.arpa"'.  Your in-addr.arpa zone name will change based on whatever your server IP address was.  My internal one happened to have s-01.mydomain.priv mapped to 10.1.10.3.
    4. Once the specialized zones for just the server were removed, I started the DNS up again.  Instead of serving four zones as it had in OS X Snow Leopard Server, it now servers two zones.  And, now, it is resolving my local machines for the mydomain.priv zone.
    YMMV.  I did note that it wasn't totally necessary to do step 3, but I never really understood the need for the specialized domain, and keeping it around would have a copy of data that would just confuse things.
    Hope that helps.  That's been the only hiccup I've noticed updating to OS X Lion Server thus far.

  • Configuring the 3750G WLC to use the Internal DHCP Server

    I want to use the Internal DHCP Server on a 3750G WLC to hand out IP's to gueat users. I'm having issues getting the DHCP server to hand out addresses for the guest network - any suggestions would be a great help.
    Configuration Details are attached.

    Configuring DHCP
    http://www.cisco.com/en/US/docs/wireless/controller/5.2/configuration/guide/c52wlan.html#wp1293808

  • I would like to know why when i make a web page and test in my local browser it works fine then when i tranfer to my server i does not work fine example i used javascript to put a prompt bar on a page and it worked fine local but on server not working

    how come when i make a web site and i test it in my local server it works fine when i tranfer to server certain things do not work example i used javascript to put in a prompt bar for a newsletter page at the server it did not work but at local it did also it works at MOZZILLA but not internet explorer i also have cs4 was wondering if there is a way to test a page in dreamweaver and then transfer   THANK YOU X-FACTOR-MEDIA

    In future, please try to make the subject line of your posts shorter. In this case the following would have been sufficient: "JavaScript works locally, but not on remote server".
    Short, but meaningful subject lines make it easier for others to identify what your question is about, and often bring faster help.

  • Internal speakers and headphones are not working

    I have hp g6 2231tx os Windows 8, brought it a month ago..now it's internal speakers and headphones are not working..I enabled in playback device from sound mixer and reinstalled drivers but still not working..it's because of hardware or software??

    Hi,
    It could be either Hardware or Software related, so try the following and let me know.
    Download the IDT Audio installer on the link below and save it to your Downloads folder.
    http://ftp.hp.com/pub/softpaq/sp58501-59000/sp58517.exe
    When done, open windows Control Panel, open Device Manager and open up Sound, Video and Game Controllers.  Right click the IDT device and select Uninstall - you should also get a prompt to remove the current driver, tick the box to allow this and then proceed with the uninstall.
    When complete, shut down the notebook, unplug the AC Adapter and then remove the battery.  Hold  down the Power button for 30 seconds.  Re-insert the battery and plug in the AC Adapter.
    Tap away at the esc key as you start the notebook to launch the Start-up Menu and then select f10 to enter the bios menu.  Press f5 to load the defaults ( this is sometimes f9, but the menu at the bottom will show the correct key ), use the arrow keys to select 'Yes' and hit enter.  Press f10 to save the setting and again use the arrow keys to select 'Yes' and hit enter.
    Let Windows fully load - it will automatically load an audio driver, but just let this complete.  Then open your Downloads folder, right click on the IDT installer and select 'Run as Administrator' to start the installation.  When this has completed, right click the speaker icon in the Taskbar and select Playback Devices.  Left click 'Speakers and Headphones' once to highlight it and then click the Set Default button - check if you now have audio.
    Regards,
    DP-K
    ****Click the White thumb to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    ****I don't work for HP****
    Microsoft MVP - Windows Experience

  • Intel 6205 wireless not working with Lenovo W520

    Loving the new W520... very fast, if only the wireless would work. Unable to get wireless interface functioning, won't even show up in ifconfig. I've appended requested wireless information, thanks in advance for any assistance.
    1) Machine Brand and Model (PC/Laptop):
    Lenovo W520
    Intel Centrino Advanced-N 6205
    Note: Wireless switch on lefthand side enabled, bluetooth led lights up but wireless does not.
    2) Wireless Brand, Model and Wireless Chipset:
    $ lspci -nn
    03:00.0 Network controller [0280]: Intel Corporation 6000 Series Gen2 [8086:0085] (rev 34)
    3 ) check interface:
    ifconfig does not show wireless
    $ iwconfig
    lo no wireless extensions.
    eth0 no wireless extensions.
    4 ) Check for modules:
    $ lsmod
    iwlagn 215351 0
    iwlcore 139688 1 iwlagn
    mac80211 269644 2 iwlagn,iwlcore
    cfg80211 167809 3 iwlagn,iwlcore,mac80211
    5) Kernel boot messages
    $ dmesg
    [ 13.497936] iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree:
    [ 13.497938] iwlagn: Copyright(c) 2003-2010 Intel Corporation
    [ 13.498058] iwlagn 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
    [ 13.498089] iwlagn 0000:03:00.0: setting latency timer to 64
    [ 13.498181] iwlagn 0000:03:00.0: Detected 6000 Series 2x2 AGN Gen2a, REV=0xB0
    [ 13.499187] lp: driver loaded but no devices found
    [ 13.502642] alloc irq_desc for 22 on node -1
    [ 13.502645] alloc kstat_irqs on node -1
    6 ) Network configuration
    $ sudo lshw -C network
    *-network UNCLAIMED
    description: Network controller
    product: 6000 Series Gen2
    vendor: Intel Corporation
    physical id: 0
    bus info: pci@0000:03:00.0
    version: 34
    width: 64 bits
    clock: 33MHz
    capabilities: pm msi pciexpress cap_list
    configuration: latency=0
    resources: memory:d5300000-d5301fff
    7 ) Scan for networks:
    not relevant as no wireless interface appears
    8 ) Ubuntu Version:
    Ubuntu 10.10
    9 ) Kernel/architecture (including 32 vs. 64 bit):
    2.6.35-28-generic x86_64
    10 ) Restarting the network:
    sudo /etc/init.d/networking restart
    * Reconfiguring network interfaces... Ignoring unknown interface eth0=eth0.
    [ OK ]
    Additionally, modinfo shows the following:
    $ modinfo iwlagn
    filename: /lib/modules/2.6.35-28-generic/updates/compat-wireless-2.6.36/iwlagn.ko
    alias: iwl4965
    license: GPL
    author: Copyright(c) 2003-2010 Intel Corporation <[email protected]>
    version: in-tree:
    description: Intel(R) Wireless WiFi Link AGN driver for Linux
    firmware: iwlwifi-4965-2.ucode
    firmware: iwlwifi-5150-2.ucode
    firmware: iwlwifi-5000-2.ucode
    firmware: iwlwifi-6000g2b-4.ucode
    firmware: iwlwifi-6000g2a-4.ucode
    firmware: iwlwifi-6050-4.ucode
    firmware: iwlwifi-6000-4.ucode
    firmware: iwlwifi-1000-3.ucode
    srcversion: 8F7F4C6196599FCA596C837

    Hi  sparhk, and welcome.
    One of the Lenovo staff who frequents the forum put out a call to help you in a private forum.  I do a little Linux, so I poked into it.  To my amazement my first Google hit was your thread where you indicate you have solved the problem.  (At least, it _looks_ like you...)
    May I respectfully suggest that a post back here indicating success would be a nice touch?  That way anyone who passes by looking for help with this issue will have a better chance of finding it.  For posterity, here it is (see post number 25):
    [SOLVED] Intel 6205 wireless not working with Lenovo W520
    Glad you got it working,
    Z.
    The large print: please read the Community Participation Rules before posting. Include as much information as possible: model, machine type, operating system, and a descriptive subject line. Do not include personal information: serial number, telephone number, email address, etc.  The fine print: I do not work for, nor do I speak for Lenovo. Unsolicited private messages will be ignored. ... GeezBlog
    English Community   Deutsche Community   Comunidad en Español   Русскоязычное Сообщество

  • S10-3t bluetooth and wireless not working with windows 8

    S10-3t bluetooth and wireless not working with windows 8. I tried everything but doesn't work at all. I don't know where to find the new drivers that are comatible with windows 8 ???!!! please help me to solve this problem because i tried everything....

    Do you still have your windows7 install files ? 
    ( installation image is usually in LENOVO_PART OKRBackup/Factory ) ? I lost them :\
    if yes I fear you have to enable it in win7 and then use it in win8
    http://rzr.online.fr/q/lenovo# g470 s103t (Please Contact me if your s10-3T is booting win7 or support bluetooth, 3g)
    Lenovo S10-3t | Model Name : 0651 | Mfg Date: 2010/06/08
    Lenovo G470 | Model Name : 20078 | M fg Date: 11/03/23 | BIOS: 40CN23WW(V2.09) 06/20/2011 | CPU: i5-2410M | Linux version 3.3.4lenovog470+ (root@lap) (gcc version 4.6.3 (Debian 4.6.3-4) ) #8 SMP Tue May 1 10:23:48 CEST 2012
    OS:GNU/Linux/Debian

  • Does option 43 matter ? WLC5508 ver 7.2 using internal DHCP server

    I am using a WLC 5508 and its internal DHCP server. I cant find anywhere I can setup option 43. However, the access points are connected in just fine. Do I need to worry about setting up a seperate DHCP server to get option 43 setup properly ?
    Thank you.

    Sorry I didnt make my question clear.
    I am using a WLC 5508 and its internal DHCP server. I cant find anywhere I can setup option 43.
    When I connect a CAPWAPP Access Point to the network, it receives IP address from the WLC 5508 DHCP service just fine. It shows up in the access points list and users can connect to it no problem.
    Do I need to worry about setting up a seperate DHCP server to get option 43 setup properly ?

  • Wireless not working, iPhone 4S, upgraded to OS6, any suggestions?

    wireless not working, iPhone 4S, upgraded to OS6, any suggestions?

    Take the troubleshooting steps recommended in the User Guide.

  • RDP to a Terminal Server via TTPT not working through routers.

    I am having problems using RDP to a terminal server through a user home router and DSL connection.
    User has a Linksys WRT5G v3 (Firmware 4.21.1) connected to a Cisco 678 DSL Modem. 
    If I direct connect the home computer to the Cisco DSL Modem everything works fine.  When I try to go through the Linksys, I can get the PPTP authenticated but the RDP client just times out.
    It would seem like this is a port forwarding issue, but I have tried to use the port forwarding to the IP address of the home computer(statically assigned) by forwarding ports 47, 1723 for the PPTP and port 3389 for RDP.
    I have seen the same issue on my home Broadband cable setup with a NetGear Router.  Having spent over an hour with the NetGear technical support without resolution. I swapped in a old Linksys Wireless Router BEFW11S4 v4 (firmware 1.52.02) and it fixed the issue.
    What is the issue with some home routers letting RDP out?  Is there a known model that it will work on?

    I believe I have found what my issue is. The older Linksys  BEFW11S4 model has a “hard coded” DHCP Server Start IP Address range of 192.168.0.X  you can only change the last octet. The newer Linksys WRT5G and WRT54Gs have a “hard coded” DHCP Server Start IP Address range of 192.168.1.X.
    Apparently this is their “dumb downed” solution for home routers.  They do not allow you to select a different subnet to hand out with DHCP but interestingly they do allow you to fully configure the LAN IP address.
    How this affected me is that my target server/network uses the same 192.168.1.X addressing scheme.
    I was able to use the newer router by configuring the LAN address to like 192.168.0.200 and turning off the DHCP server.  Then I assigned a static IP address to the computer in the home network to something like 192.168.0.250.  Then I could successfully use PPTP and RDP to connect to a terminal server.

Maybe you are looking for

  • Exporting macro along with data - BEx web

    Hi, I have to send BEx web data along with a macro. The purpose is every report user down loads in his desktop gets an unique macro along with the data. The user can later use that macro for further analysis of the downloaded data. I was reading thro

  • When did After effects become 64-bit?

    Hi. I was wondering if After Effects is 64-bit? From what I read, it is. Secondly, What version was 64-bit? Did it start in 4? Thank you.

  • QIP 7100 2 boxes constantly turning off

    I've got 2 QIP 7100 2 boxes they turn off constantly (go into standby) this messes with my DVR! I don't want verizon's DVR, i want my DVR to work. It would work great if the boxes would stay on for more than 30 minutes to 2 hours at a time.  What can

  • Straight talk can not access app store

    I just switched to Straight Talk, after configuring the APN I can access the internet with my cellular data.  However, I can not use, mapquest or any other apps on cell data.  I can not even access the apple app store.  Any ideas what could be causin

  • InDesign Mac Trial?

    Alright, so I downloaded the InDesign Mac Trial with Creative Cloud on my MacBook Air. I'm using it to make a magazine for my designing class in College. I'm trying to move the simple things such as pictures and text, but my track pad won't allow me