Internal hard disk is not visible in disk utility in Macbook Pro

Hi All,
I am trying to repair my mac. But in disk utility, the hard disk is not visible to proceed. Its showing disk0 -> volume with only 1.79GB. and all the options are disabled. The capacity of my mac book pro was 500GB.
Please help me in solving this issue
Thanks in advance....

So you've booted into your Recovery partition and you don't see any drives in Disk Utility to select in Recovery mode?
If the drive cannot be repaired, it's likely dead and you'll need to purchase a new internal drive.
Good luck,
Clinton
MacBook Pro (15-inch Late 2011), OS Mavericks 10.9.4, 16GB Crucial RAM, Crucial M500 960GB SSD, 27” Apple Thunderbolt Display

Similar Messages

  • Hi, I just put a new internal hard disk to my MacBook after formattimg it and I don't know how to install the OS X? Any help please

    Hi, I just put a new internal hard disk to my MacBook after formattimg it and I don't know how to install the OS X? Any help please

    Be sure you have prepared the new drive correctly:
    Drive Preparation
    1.  Boot from your OS X Installer Disc. After the installer loads select your language and click on the Continue button.  When the menu bar appears select Disk Utility from the Utilities menu.
    2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area.  If it does not say "Verified" then the drive is failing or has failed and will need replacing.  SMART info will not be reported  on external drives. Otherwise, click on the Partition tab in the DU main window.
    3. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, set the partition scheme to GUID (for Intel Macs) or APM (for PPC Macs) then click on the OK button. Click on the Partition button and wait until the process has completed.
    4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
    5. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, check the button for Zero Data and click on OK to return to the Erase window.
    6. Click on the Erase button. The format process can take up to several hours depending upon the drive size.
    Steps 4-6 are optional but should be used on a drive that has never been formatted before, if the format type is not Mac OS Extended, if the partition scheme has been changed, or if a different operating system (not OS X) has been installed on the drive.
    When formatting has completed quit DU and return to the installer.  Complete the OS X installation.

  • Stop the beeps with the 7200 rpm hard disks of the MacBook Pro

    http://www.hardmac.com/news/2009/07/13/stop-the-beeps-with-the-7200-rpm-hard-dis ks-of-the-macbook-pro
    Stop the beeps with the 7200 rpm hard disks of the MacBook Pro
    from HardMac.com by [email protected] (Lionel)
    At the beginning of week, we have spoken about the unpleasant beeps made by the 7200 rpm hard drive proposed as an option in the MacBook Pro 2009.
    A solution has been found, the details are given by Rémy.
    These tedious beeps occur when the disc is inactive and are caused by a system
    to reposition the play-back head carried out in a repetitive way.
    In addition to the beeps of the hard drive, Mac OS X displays the pretty multicoloured wheel during some seconds while waiting for hard drive to finish these loadings and unloadings of the play-back head.
    The solution comes with a utility of the name hdapm (for Hard Disk Advanced Power Management) which makes it possible to change the level of energy management (APM) of the hard drive.
    Hdapm can be downloaded from : http://mckinlay.net.nz/hdapm; hdapm being a command line utility, it is thus necessary to use the Terminal (which is in /Applications/Utilitaires).
    After copying hdapm into your user file, the command to enter is:
    sudo ~/hdapm disk0 max
    disk0 corresponds to the disc to regulate knowing that hdapm should function with any ATA disk supporting APM
    max is the level of APM which is a number ranging between 1 and 254 included
    the word following are preset and can used in the place a number for the level of APM
    max (maximum performance) is the parameter to use to eliminate the “beeps”.
    min (maximum economy of energy)
    default (returns to the default setting)
    The level of APM is a temporary adjustment in the firmware of the hard drive, this adjustment is lost when the disk is powered down and it is thus necessary to redo this at each for each start up.
    To install hdapm so it is launched at each start-up, it is necessary to copy hdapm to the hard drive (/usr/local/bin is advised) and to copy the file hdapm.plist in /Library/LaunchDaemons.
    It will be can be necessary to you to edit hdapm.plist with the desired parameters; the default settings are: the repertory where hdapm is /usr/local/bin, the hard drive is regulated on the first (disk0) and the level of APM is the maximum.
    You can simply copy the file hdapm into /usr/local/bin file if you want to avoid modifying Plist.
    Simplest way to reach these files is to use the Go/go to the file and to copy/paste this address before validating.

    Yeah, I don't buy that. I spoke with Seagate a couple of months ago when I was looking for the impossible to find 500 GB 7200 RPM HD and asked them that very thing. They told me it would work fine, but I should disable SMS. Apple told me the same thing. I ultimately waited and got a non G-Force model, but Seagate told me it would work.
    I also don't believe that they'd OEM the drive to Apple knowing it wouldn't work. That makes absolutely no sense. If Seagate knew the G-Force drive would not function properly in an Apple MacBook/MacBook Pro, and they OEM'd it to Apple for that purpose anyway, what does that say about Seagate?
    I admit it's odd that the used the G-Force model given the presence of SMS, but apparently Seagate has prioritized the manufacturing of the G-Force drives and probably offered it to Apple.

  • Where could I buy a new hard disk for my macbook pro 15''(MB986CH/A)

    Does anyone know where I could buy a new hard disk for my macbook pro 15''(MB986CH/A) (mid 2009)? The hard drives sold in Apple Store are not for macbook pro... Thanks a lot!

    At one time Apple use to put an Apple firmware on the drives installed into Mac computer. That is not the case anymore. And even if they did that firmware was just to indentify the drive as an Apple drive. Those same drives would work in any computer and any drive would work in a Mac computer. Same is true today. There are NO Apple Mac drives. Apple uses the exact same drives as any other computer.
    Apple uses the exact same hardware as all other computers. Same CPU, GPU, RAM, Drives, DVD drives you name it, it is the same as any PC.
    Good Luck but just because you go to a Mac-centric store doesn't mean it is any different then what you would buy some place else, other then it may cost more from one of those Mac-centric places.
    Joan_hk wrote:
    Thanks. According to my previous experience with an old white macbook, there might exist some compatibility problems for the hardware I bought from computer parts store...That's why I want to find an official retail store or reseller.... Thanks anyway!

  • Can I upgrade hard disk storage of Macbook pro retina 15inch 2013 late after purchasing?

    Can I upgrade hard disk storage of Macbook pro retina 15inch 2013 late after purchasing?
    I currently have 256GB.

    Actually you can:
    http://eshop.macsales.com/item/OWC/SSDAP12R480/
    But installing this will void your warranty!
    Ciao.

  • Re: How can I add a second internal hard disk to a Satellite Pro P200?

    I have a Satellite Pro P200 with a single internal hard disk. There is a second bay under the computer for another internal hard disk but I have not been able to find any information about it. There is enough space for a 2.5" SATA drive but I cannot see a connector.
    I contacted Dutch Toshiba Customer support who said that it was the official policy not to provide any information about a second hard internal disk. They also said that they would not supply any parts to make it possible.
    Can anyone provide some more information?

    Hello
    I have the same notebook with the same situation. The fact is that covers and the construction for all P200 notebooks is the same but notebooks are delivered with different hardware platforms. Some models are delivered with two HDDs.
    Other models (like yours and mine) are delivered with one HDD but without possibility for upgrade with second HDD.

  • Internal Hard Drive is not visible in Finder or Desktop or anywhere

    The problem first and then the details.
    I cannot see my systems hard drive, No icon shows up on the desktop, and it is not visible in the Finder.
    It does however show up in Disk Utility.
    I have repaired permissions and repaired the disk, both from within the OS and also from the install disc during a reboot.
    Not here are some details. This is both a fresh install of the OS AND a brand new drive. I just had it installed today and then reinstalled the OS.
    While going thru the process of reinstalling all my software, something froze for no good reason, and I eventually had to force quit the finder and when the system wouldn't shut down, I had to physically power it off.
    Upon rebooting, my systems HD is no longer visible.
    I suppose I can try and reinstall again, but I feel like there has to be a smarter way to deal with this.
    Any suggestions?

    Have you confirmed that in Finder > Finder menu > Preferences > General and Sidebar tabs that the boxes to show hard disks are checked?
    Assuming they are checked, you may a victim of the 'invisible drive' problem. See Francine's helpful tutorial for the fix:
    http://www.pinkmutant.com/articles/invisible.html

  • Crucial m4 256 GB internal SSD not showing in disk utility on MacBook Pro a1226 (late 2007) 2.4 ghz.

    After the original Fujitsu 160gb hd died in my MacBook Pro (model A1226), I was advised at the Mac store to upgrade to a SSD.  I installed the crucial m4 256gb internal SSD and powered on MacBook Pro from the Snow Leopard install disk so I could use disk utility to erase and reformat the new SSD.
    The problem is the SSD is not showing up in disk utility.  I have opened the computer twice and checked cable connections and still no luck.  I have powered off computer and let sit for a while and tried again.  I check compatability on crucial site before ordering SSD so I don't know what the problem is.  Bad disk?

    You were given bad advice.
    Return/Sell the SSD and buy a 7,200 RPM hard drive instead, it should work fine and a more of a match for your older machine.
    Your Mac doesn't have the faster SATA connections for a SSD also 10.6 isn't equipped for SSD's only hard drives, your basically putting a Ferrari engine in a Yugo, it can't handle it.
    The 7,200 RPM drive will give you the performance and more drive space than a SSD anyway.
    Follow these instructions when you erase and install 10.6, it will give the best results.
    How to erase and install Snow Leopard 10.6

  • I am using a Mac Book Pro. Now I am trying to read a LaCie 1 TB external hard disk. The MacBook Pro hangs while reading the LaCie external hard disk.

    I am using a MacBook Pro. I have my movies stored on a Lacie 1 TB external USB harddrive. (42 Movies in HD - 538 Gb in use). When I try to read the LaCie external drive, my MacBook Pro is "hanging". Only a "hard reboot" helps to get my MacBook Pro up and running again. The MacBook Pro starts to read the drive, but half way he "stucks". I can read the LaCie drive without any problem om my windows machines, so the LaCie drive is O.K. Anyone familiar with this problem?

    The drive is formatted NFTS, otherwise the drive can not handle large files under Windows. And yes, I can see the drive in Disk Utility.
    I can even see the files (partly) untill my system is hanging.
    Hans

  • What is the best way to add hard disk space to macbook pro?

    I'm running out of disk space on my macbook pro. What is the best way to add disk space?

    another way of doing it is to replace your hard drive with a larger one.
    if you're technically capable, it takes 10 minutes for the swap and an hour minimum to clone your hard drive or do a data transfer.  all depends on how much data there is to trandfer or to clone.
    good luck.

  • External hard disk compatibility with Macbook Pro

    I am a PC user and I am thinking of getting a Macbook Pro but have some reservations regarding the following:
    Will my existing USB external hard disk drives continue to work with MBP?
    Will I have any folder sharing issues between my PCs and MBP?
    Or, should I really need to dual boot or virtualize Windows 7 to avoid these issues?
    Any tips on how to dual boot or virtualize Windows 7 in MBP would also be much appreciated.
    Thanks!

    Will my existing USB external hard disk drives continue to work with MBP?
    There should be no problem. Can you tell us how the drives are formatted?
    Will I have any folder sharing issues between my PCs and MBP?
    You shouldn't have any issues it's very easy to set up. Read this: http://support.apple.com/kb/HT1812?viewlocale=en_US
    Or, should I really need to dual boot or virtualize Windows 7 to avoid these issues?
    That's up to you. If all you want to do is file sharing then there is no need to dual boot, simple networking will solve that problem.
    Any tips on how to dual boot or virtualize Windows 7 in MBP would also be much appreciated.
    You can use Boot Camp or Vitualization using Parallels or VM Ware Fusion. All three will allow you to run Windows on a Mac. If you go the Boot Camp route you have turned a partition of your Mac into a PC. If you use Fusion or Parallels this allows you to run MS Windows inside OS X. Performance for most tasks is excellent.
    I would also suggest you study both:
    Switch 101
    Mac 101
    Roger

  • Questions regarding hard disk replacement in MacBook Pro Early 2008 Edition

    Hello -
    You folks probably get this a lot but I have a MacBook Pro Early 2008 edition and would like to upgrade the base 200 GB 5400 RPM drive to a Seagate Momentus 7200.4 drive. I have a few questions regarding this, and would appreciate any feedback.
    1) Does anybody know if installing a new hard drive in a MacBook Pro would cause the warranty to be invalidated? I don't believe a hard drive is considered a user replaceable part, at least from what I read, and I would like to know if replacing it myself would void AppleCare.
    2) Does anybody have any experience with the Segate Montentus 7200.4? I'm interested in how reliable the drive is and how much heat it generates. I've quickly discovered that I can use my MacBook Pro as an oven in tight spots and would like to prevent it from cooking its own internals.
    3 random) Does anybody know at what temperature the system actually overheats? I'm seeing 171 F and this is with smcFanControl turned up to the Higher RPM mode. I'm a little nervous when I'm running WoW and the system is averaging above 170 with smcFanControl totally cranked up to 6000 rpm.
    Thanks everyone!

    Thanks for that. I've had mixed results with both Seagate and WD, but less issues historically with WD. My experience with IBM/Hitachi makes is nearly impossible to recommend their products, so based on what I'm seeing the Western Digital Scorpio Black looks like the best bet. Do you happen to know if Apple will do hardware installations outside of warranty repair scenario's? Ripping open my only notebook to perform "involved" hardware maintenance is not something I'd prefer to do, even with my technical background.

  • I'm getting a -2003F error when trying to run the internet recovery after installing a new hard disk in my macbook pro, any suggestions?

    After installing a new hard drive in my 2011 macbook pro, I'm getting a apple.com/support -2003F error when trying to run the internet recovery.  Any suggestions?

    Did you format the new HDD?  What is the status of the old HDD?
    Do you have an early or late 2011 MBP?
    Ciao.

  • My hard disk on my macbook pro is full and most of the memory is from iMovies. I have a back up disk which is 1 terabyte and I was wondering if it is possible to move all my iMovies onto it without creating any problems. If possible how do I do this?

    Hi there, I am a great fan of doing films. the big problem is I have filled up the hard drive on my Mac Pro. I have 1 Teribyte Time Capsul where everything is automatically backed up. I want to use this to transfer my iMovies file to the Time Capsul to create more sapace on my MacPro. If I do this will it create problems when I use iMovie?
    Could someone advise me the best way of doing this? Thnx!

    Have a look here...
    what-to-do-when-your-hard-drive-is-full.html

  • 2nd Internal Hard Disk Not visible on desktop

    Hello,
    Last night I was trying to rename some files and my G5 was acting very slowly. I relaunched the finder and it seemed to fix the problem. I resumed renaming files and it kept locking up. After the fourth time this happened, the system locked up and I pushed the front power button until the system shut down. When I turned the computer back on, my second internal hard drive was not visible. I looked in disk utility and did not see it, and it is also not visible in about this mac. Help!!!

    HI
    I have a similar problem that the second drive does not always appear on starting up from cold but usualy appears on a hot restart
    second drive is a Hitachi HDS725050KLA360 primary drive: HDS725050KLA360 (465.76 GB)
    (Telephone support was useless)
    It has been operating since March Photoshop and Aperture applications I do power down every night.
    And back up to external just in case I loose it but would prefer to have more confidence in its reliability
    Has anyone else had similar experience ? and any idea what might be the cause?

Maybe you are looking for

  • Error - The registration of the service "User Profile Service" has failed. The user profile can not be loaded

    I am running an environment with an Active Directory and Terminal Servers. I have searched high and low for resolutions to this error but I cannot find anything related to my situation, let me explain further. The fixes I found are related to local u

  • How can i see hierarchy modifications?(knvh)

    Hi, I need to see all the modifications made on a customer hierarchy (if a customer under the hierarchy has been removed date and time of its removal, if a new customer has been added). In case this can be attained only using a query which table shou

  • Error with ZCM 10.3.3 Agent

    Hi, I got this error with 10.3.3 ZCM agent. Client is XP SP3. Server is w2K3 64Bits Full Message: An error ocurred during a general refresh in module: Registration Module. Error Message: Could not load file or assembly 'Novell.Casa.Client.Auth, Versi

  • Input-/ouputStream hanging

    Hi all. I'm having some trouble with sending an XML-file via outputstream. I think the problem is, that the receiving part, a SAXBuilder, doesn't recognize any end of file in the incoming data, and therefore keeps reading. My assumption is based on t

  • I am Getting the classcast error while using the webservice client

    Hi , Iam getting classcast exception while trying to get the connection Object throurh the webservice client. The details are: the ra.xml <resourceadapter-version>1.6</resourceadapter-version> <resourceadapter> <resourceadapter-class>oracle.apps.cont