Internal hard drive does not mount in disk utility

My internal hard drive no longer mounts in Disk Utility. It is grayed out. I have extraordinarily frequent spinning beach ball/freezes, in Safari or Apple Mail. The most recent symptom: upon rebooting or just starting up, I see flashing black on the display. This has been occuring for more than six months. Of course, I have made total and frequent backup's. I bought new RAM, but have not yet installed it, and I susect this might help. I have done repeted troubleshooting many times each:  Apple's Disk Doctor, Repaired Permissions, Reinstalled the Mac OS, safe boot, Alsoft's Disk Warrior, Apple's longer Harware Test, etc. I have worked as a new user, too. All tests done report that all is well. What od you thnk the problem is? Must I drive 1.5 hrs. each way to the Genius Bar at my nearest Apple Store? Might I try to erase the hard drive as a fix? I hate to do this, only as a last resort, as it is so time-consuming. Should I just update my Mac OS? Please advise, out there, if anyone can offer any advice, I would be greatly appreciative.

The list of issues you posted probably would not get shorter if you attempt to 'upgrade them' away, as usually that kind of effort is not effective yet may expose more of the same problems while not necessarily revealing the original weakness. Another OS X installed over a set of problems seldom helps.
How full is the hard disk drive? If it is too full, or has been very busy in use several years, it may be time to replace the HDD and perhaps put a larger capacity one in the computer. And if the main computer hardware checks out OK (tested under a variety of duration and stress tests) then also consider a RAM upgrade if the device is not already at the maximum capacity.
When was the last time the hard disk drive was devoid of content, maybe wiped -- erased and reformatted by a third party disk utility or have a utility overwrite the entire HDD with zeros? This used to be a common tech service in the course of a major effort to restore a Mac. Or Defragment?
If you can do the latter, this could help resolve bad sectors and remove old data or corruption on the hard drive. Or get a new HDD and before committing a new OS X install & apps to it (or a re-clone of a complete backup) test the drive and be sure it is ready for use. Not all new drives are perfectly ready; some need to get exercise first.
I'd bet on a new hard disk drive of larger capacity (also note spin RPM rate and data speeds) and a full RAM upgrade.
If you have a backup clone on an external hard disk drive (in a boot-capable enclosure) you could really go to town and before you erase the main/only hard drive, make a backup clone and test its ability to boot the Mac. Or put the old drive and content in a suitable boot capable enclosure of the kind with its own power supply, and deal with it later.
Then consider a later version OS X -- whatever most recent version that model can support... {edited}
Good luck & happy computing!

Similar Messages

  • Internal hard drive fails to mount in Disk Utility.

    My internal hard drive fails to mount in Disk Utility for the past year, so I cannot verify it. However, it does mount in Disk Warrior. (1) I am concerned that it will not mount within the Apple software, and what that bodes for my computer. (2) I also have MANY spinning beach balls daily and have to use the power button to reboot. I just bought extra Crucial RAM and have yet to install it. Somehow, I don't think it wil help my issue # 1 though. Please advise, anyone out there! Thank you.

    No, there are never any errors like that. Also, I have upgraded the Mac OS from 10.5 to 10.6.8. That did nothing. I backed up my Users = Christina folders to a good, 15 year old Firewire 800 La Cie 1 TB  external hard drive. I also tested using the Apple Hardware test, which showed no problems, and Alsoft's Disk Warrior and defragged, and fixed a very minor issure re directory count, probably resulting from many improper shutdowns lately due to frozen spinning beach balls. None of these procedures alleviated the issues, and I still have the same issues: mainly that super-frequent spinning beach ball. Do you think I ought to install that new RAM sitting here finally? Perhaps it is a lack of RAM??I only have 2 lousy GB's of RAM after all! Thank you so very much for a reply.
    Message was edited by: Flamingcreatures

  • Replacement Hard Drive does not appear in Disk Utility.

    I've replaced the defective HDD in my MBP(A1278) with a 500GB Western Digital one after it failed the Hard Drive test in AST. The old drive is detected internally without issue but the new one does not show up in disk utitlity. I have reformatted to use a GUID table and have made sure it's partition is OSX Journaled. It doesn't show up at all. I proceeded to do an install using a USB drive adapter and the OS installed just fine(same drive), when I put it back in the MBP it still doesn't detect. I would suspect the cable but the old drive shows up and runs diagnostic just fine(fails). I've actually gone ahead and tried three other new drives(2 seagates(500GB, 1TB XT) and 1 500GB HGST) and none of them detect, only the original. Am I missing some sort of firmware update or is there a limited physical issue?
    All help would be appreciated, genius bar isn't an option, the closest one is 400km away.

    Until you replace the cable you won't know for sure. Do you have a SATA to USB adapter to connec these other drive to and to connect your original drive to? If you do connect the original drive and do a Verify Disk in Disk Utility. If it comes back OK, no repair needed or even if a repair is need that succeeds, your original drive is OK and it is the cable that is causing all the problems.
    I suggest you stay away from WD drives. They don't have a good track record with Mac computers.

  • External Hard Drive does not mount

    My 2TB external hard drive does not mount and I cannot get it to.  Have tried turning the hard drive off and then back on.  No response.  Any thoughts as to how I can get it to be recognized?

    You can try doing a SMC reset, if it doesn't work the first time it's totally OK to reset the SMC several times.
    SMC RESET
    Shut down the computer.
    Unplug the computer's power cord and all peripherals.
    Press and hold the power button for 5 seconds.
    Release the power button.
    Attach the computers power cable.
    Press the power button to turn on the computer.
    PRAM RESET
    Shut down the computer.
    Locate the following keys on the keyboard: Command, Option, P, and R. You will need to hold these keys down simultaneously in step 4.
    Turn on the computer.
    Press and hold the Command-Option-P-R keys. You must press this key combination before the gray screen appears.
    Hold the keys down until the computer restarts and you hear the startup sound for the second time.
    Release the keys.

  • Internal hard drives won't appear in Disk Util

    I have a bizarre problem with my hard drives now. I'm on a 2.4GHz Core2Duo Macbook Pro 15" with 10.5.4. I've switched the hard drive a couple of times before with no issues whatsoever. Now, with the exception of the brand new one that won't hold an install, my internal hard drives don't show up in the install disk's Disk Utility.
    I got a new hard drive to try the other day, installed it, booted to my OSX install disk to use Disk Utility. I switched the new disk to GUID and formatted it as journaled like usual. It took 4 hours to do the install, then after the restart it tanked. It booted back to the install disk where I checked it out. It could not repair the file system, and the drive was not "mounted". I mounted it, repartitioned and formatted it, and installed again. This time it stopped halfway through the installation and said the drive might be corrupt.
    I unplugged the cable and battery, held the power button for over 5 secs, then just let it sit for about 10minutes with no power source while I thought about this. I put the original drive back in, booted into OSX, and put the new hard drive in an external USB enclosure. I formatted it while in OSX, then rebooted into the install disk and installed OSX on it while it was in the USB case. It took the installation more quickly (about an hour and a half...still not 20min like my old 7200rpm Hitachi 200g), then I booted into its OSX while in the USB drive. It booted ok, so I downloaded the updates and clicked to install them. It then went into a revolving restart. Eventually I decided it was not doing this because it was happy so I shut it off.
    I swapped the hard drive out with another new one, and this one would not complete an installation while inside the computer either. It acted similarly while in the USB case. HOWEVER it would always show up as unmounted after a restart and would not recognize the drive inside the computer as a bootable disk.
    I put my original drive in there to give up, and it gave me the ? folder. I booted to the install disk and it did not show up in the disk utility. I put my old hard drive in the USB case, booted to the install disk, and it showed that it was there, but unmounted and it could not repair the file system.
    I repartitioned my hard drive (i have time machine working..not a huge setback) in the USB case and put it back in the computer. It still would not show up in disk utility. I put it back in the USB case, installed OSX onto it (in about 20min), restarted a couple times, saw that it was working, put it into my computer, and got the ? folder again.
    I went out and bought a stardard 160GB SATA 5400rpm Seagate drive to try in there, and this fresh drive is not recognized inside the computer either when I boot into disk utility.
    The brand new hard drive WILL show up in Disk Utility when I boot to it from the install disk, but it will not survive a complete installation.
    So now I'm running OSX from my original hard drive in a USB case until I can figure out why the old disk recognized inside my laptop is the new hard drive upgrade, but it cannot complete an installation on it.
    I'm originally a Windows slave, so I can only think in terms of AHCI or SATA-card drivers, or screwed up bios. But this is all pre-os-boot, and the apple firmware seems to be pretty automatic in picking the right settings to see stuff.

    I kind of feel like drawing a flowchart to show all that I've tried. Its difficult to keep everything intelligible while listing the entire last week's efforts at 2:45am. :-/
    http://www.ocztechnologyforum.com/forum/showthread.php?t=41951
    I also explained it here, perhaps a bit differently. Maybe some reply there might spark someone's memory of a possible problem. I understand the nature of computers (been 100% geek for 20 years), but I'm hoping there's someone out there with the specific Apple expertise to help me out. Eventually the processes I've taken and my specific situation will become clearer as the questions widdle away at this.
    My original 7200rpm SATA drive that works fine won't show up when connected to the SATA cable. I've repartitioned it with HFS, and repartitioned it as free space in the USB enclosure. It simply won't show up in Disk Util. Same with the brand new test SATA drive.
    The new SSD SATAII does show up, but after a 4hr install the partition is unmounted and won't show up as a boot option. I can boot to the install disk and repartition it, reinstall, or remount it. But it will never be mounted to be booted from while connected to the computer. I've had 2 of the SSD's to try, one survived one restart, then went into a never-ending restart cycle after I installed the updates. The 2nd has never successfully been mounted after the install to boot from. Now nothing can be mounted to boot from within the computer. I have to boot off of any of these drives from the USB enclosure.
    If I install OSX on them while in the USB enclosure, that works, but they will not mount when connected to the SATA cable inside the lappy. The platter style SATA drives won't even be recognized...
    Thanks for the instant reply, this is driving me nuts 'cuz it makes almost no sense. Thanks so much to everyone that contributes. I appreciate everything.

  • Internal Hard Drive will not mount -- need help!

    My Mac Dual 450 has been a constant problem since I installed Tiger several weeks ago. There have been crashes every day. Disk First Aid did not help. Then I discovered I had TechTool Deluxe which I had gotten from Apple a few months ago. It has diagnostics for just about everything you can think of. I tried it. Big mistake.
    Everything came out OK except it said there were some bad blocks, and an invalid BTree node size 8.0 (whatever that is). I tried to get it to repair the HD and it said it could not, that the HD was not mounted (I had booted from TechTool disk). Then I tried to reboot from the internal HD and I got a big bad black box saying that I had to restart. I tried that many times and kept getting the message. I booted from the Apple Tiger install disk and tried to run Disk First Aid on my HD but it said there were problems and Disk First Aid could not correct them because the HD was not mounted. I tried this and the TechTools Disk many times. Same result.
    I then booted from an external system 9.2.2 HD and tried to use the Disk First Aid on that. Same result: it said the Macintosh HD (my internal) was not mounted so Disk First Aid could not repair it.
    I have tried everything I could think of (option-boot, C-boot, etc) and nothing will let me boot from the internal HD or even mount it. I spent quite a bit of time with AppleCare rep and he could not succeed in getting the HD to mount.
    He suggested either trying Disc Warrior which I do not have, or possibly resetting the PMU on the logic board and he sent me instructions for that, which seem ominous to say the least. And I doubt that it would solve my problem since the computer sees the HD, it just can't mount it. Resetting the PMU seems to be for computers that can't see the HD and won't start. But mine does just fine with other start-up disks.
    Are there any suggestions on what else I can try? Is there a program that can be downloaded that mounts hard drives?
    My Mac Dual 450 has 1.25 gb of RAM.
    Thanks for any help. I need it fast.

    Thank you for your suggestions and your continuing interest in trying to solve my problem. I rebooted with CMD + S and got the black screen with white text. Unfortunately I could not type anything on it. I typed /sbin/fsck -y and hit return. Nothing showed on the screen. I waited awhile in case this was one of those situations where it is hidden. But nothing happened. I tried the whole sequence a couple more times and same thing: I was unable to type anything that would show up on the screen.
    Am I missing something here? I tried typing holding down various keys and could not get anything to register.
    For what it is worth, the last line that showed on the screen is "panic. We are hanging here..."
    I do not think that is related to what I typed since it was there when the screen first appeared, but could it nonetheless have somethng to do with my computer or hard drive?
    I am right now installing system X.4 onto an external HD. If I can get that to boot and work OK, I can just use that for awhile until I get the internal either replaced or repaired.
    If you see my previous posts, I had a devil of a time installing system X.4 to begin with. Maybe my HD was troubled all this time??? Or could there be some other underlying problem with my Dual 450? I suppose I will find out when I try to boot from the external.
    Incidentally, I have an external HD with 9.2.2 on it and have had no trouble booting from it or using it.
    Thanks again for your help.
    Power Mac Dual 450   Mac OS X (10.4)  
    Power Mac Dual 450   Mac OS X (10.4)  

  • External hard drive does not mount after sleep

    I am using a brand new Seagate 2 TB external hard drive for my backup drive.  More often than not, when the computer goes to sleep, the icon for the drive is gone from the desktop when the computer wakes up.  I have to unplug it from the computer and reconnect it, then it mounts and works fine.  I have it plugged directly into the computer's USB port.  The drive uses USB3.  As far as I can tell, it does not exceed the power requirements of the USB port.  It is the only external hard drive I am using at the moment.
    I should note that the same thing was happening with my last hard drive.  That was a Western Digital 250 GB drive with an independant power source connected by firewire.
    I am running OS 10.6.8 on an Intel circa 2009 iMac.  My external drives worked fine for years, and it seems in the last year or so is when this started happening.

    r_dizzle wrote:
    Another point of note is that both the HD and the keyboard are connected to the iMac through a 7 port USB hub.
    I think this might be the issue. If the iMac is waking back up, it will likely be waking up this HUB, but the HUB might not be re-initialising the connection between OS X and the external drive or the keyboard.
    After waking the iMac, if you unplug the external drive from the HUB, then plug it back in again, does OS X pick it up again? Have you tried plugging the external drive directly into the iMac and then testing what the result is?
    If you read back on what you've said, you pointed out that you have a USB mouse that you use to wake the iMac from sleep. Is this mouse directly connected to the iMac? If so, it surely can't be a coincidence that a directly connected USB device can wake the iMac from sleep, but any USB devices connected to the iMac via a USB HUB cannot.
    I would suggest you test the drive as it is directly connected to the iMac. I would complete the same test with the keyboard too. I think you'll find it's the USB HUB.
    I hope this helps.

  • Fat32 External Hard Drive does NOT mount on Windows XP Pro under boot camp

    I have a gateway 160gb portable external HDD. When it came pre-formatted in NTFS. It mounted on Windows XP under boot camp or Vmware Virtual machine very well.
    I then formatted it under HFS+ to use it with superduper.
    Now that I want to convert it back to NTFS. I formatted it under Fat32 so that windows can recognize it and I can format it again under NTFS.
    The drive mounts fine on Mac OSX leopard but not on Windows XP (bootcamp or Vmware VM). Could someone help? I need this drive to be under NTFS so that I can store work related files which can only be run on Windows and some of the files are larger than 4gb.
    Thank you

    Under Disk Utility>Partition select anything other than 'Current' under 'Volume Scheme', then the format field will light. However, you should have been able to format under Windows Disk Management once it was online. See:
    http://www.microsoft.com/windowsxp/using/setup/tips/advanced/ntfs.mspx

  • Iomega Ultra Max Hard Drive does not mount

    It worked splendidly for many months, but suddenly my Ultra Max will no longer mount on my iMac G5 with OS X 10.4.11, nor on my old iBook or new iBookPro. It is not listed in Finder.
    In its final few weeks it was first listed in finder and would work for half an hour or so and then suddenly disconnect out of the blue. But now it is, apparently, even worse.
    I went to the iomega support page, followed the suggested procedure of clicking the Apple icon, then About this mac, and finally found the Ultra Max listed under the FireWire arrow. There it lists as file system HFS+. Presumably I therefore do not have to (re-)format the hard drive.
    What could it be?

    There is indeed something wonky with those models (I have the 750 GB one). I am in the process of having it fixed/replaced now, but here is an interesting bit of news:
    - Apple refers me to Iomega for the return and service
    - Iomega accepts the case and will replace the unit
    - I pack and ship the unit, which costs me around 60 EUR (from Norway to The Netherlands, including customs-processing fee)
    - Iomega informs me they do not cover shipping
    - Apple Store informs me that they will not cover shipping, since the product (in their world) is out of warranty (which it isn't)
    Now - what do I do about those 60 EUR I paid for shipping the unit? If this was any other Norwegian internet computer store, they would have covered the shipping for me -- it is the LAW, they have to -- since the product is under warranty. But, since Apple tells me "No, Iomega handles their own support, you have to talk to them" I had to, and when they don't want to pay for the shipping.. well.. what do I do? I could have bought a new (and bigger) drive for the cost of just returning the unit for repairs.
    I am aware that the Apple Store continously is hammered for being "customer alienating", but I have never had such an dissapointing experience as a consumer. Ever.

  • 1.0 terabyte Internal Hard Drive does not fit in my HP G70-200 Notebook

    Replacing my Toshiba  MK3252GSX ATA 300GB Hard Drive with a Western Digital 1TB but when I went to replace the hard drive  dimensions of the WD drive were bigger then the hard drive compartment. Does anyone know where I can get a 1TB HD that will fit into the HP G70-200 I have looked but have not had any luck finding.

    Hi,
    Hope you've done research before going out to buy 2.5" 1TB HDD. They won't fit to our current laptops physically because they are a bit thicker and laptop vendors are trying to make their laptops thinner. Hope one day WD, Seagate, Samsung, Toshima, Hitachi .... will make their 2.5" 1TB HDD's thinner or better, they make SSD's cheaper and bigger (in capacity).
    BH
    **Click the KUDOS thumb up on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

  • External Hard Drive does not mount after connecting to airport

    Hello,
    I tried finding a solution to this problem already, but people that posted were having issues seeing the drive connected to the airport, while I am having the opposite problem.
    After I tried connecting my USB drive my new airport extreme and it worked there and I tested speed and whatnot, I disconnected it and plugged it back into my iMac and now it will not show up anywhere, and will only show up when connected to the airport.
    Basically I want my drive that was connected to the airport to connect to my mac again because it is not working.

    Zerimar wrote:
    After I tried connecting my USB drive my new airport extreme and it worked there and I tested speed and whatnot, I disconnected it and plugged it back into my iMac and now it will not show up anywhere, and will only show up when connected to the airport.
    To clarify, when you connect that drive directly to your iMac it doesn't appear on the Desktop? Do you have Finder preferences set (in the General tab) to show "External disks"? Do you see the drive in Disk Utility?

  • My internal hard drives don't appear in disk utility. Can't install os X

    Hi,
    I have a macpro. In this computer are 4 1TB hard drives. They were set up as a raid set. I booted my comp with a snow leopard install disk and opened raid utility to delete the raid set so I can install os X on one hard drive and use the other hard drives to store files. After deleting the raid set, I opened disk utility to find no disks in which I can reformat or even install snow leopard. What steps do I take now to ensure all disks are useable and that I can install my operating system on one of them?

    Drive Preparation
    1. Boot from your OS X Installer Disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu.
    2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. SMART info will not be reported on external drives. Otherwise, click on the Partition tab in the DU main window.
    3. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, set the partition scheme to GUID (for Intel Macs) or APM (for PPC Macs) then click on the OK button. Click on the Partition button and wait until the process has completed.
    Now if you wish you can repeat Steps 2 and 3 on the other three drives. Or you can do it after installing OS X.
    Once you have one drive reformatted you can quit DU and install OS X.

  • MacBook Optical Drive Does Not Show in Disk Utility

    Hi Everybody,
    So I put a CD in my CD/DVD drive on my white 2009 Macbook and it made a funny sound. The CD did not register with the system. And when I open Disk Utility, it doesn't recognize the optical drive at all.
    Is there anything I can do?
    Many thanks!

    Can you or did you eject the cd? Then check apple (upper left corner) about this mac/ more / serial- ata in left panel. Does it show there. Recheck disk utilities and see if it is now there. No? Restart holding down command/option/p/r/ for three chimes. Try another cd. Same? shut down and do SMC reset.  Remove battery if you can and power cord hold down start button for 10 seconds. If battery is not removable hold down command/option/shift while pressing down the start button for 10 seconds.  Restart and retry. If still no drive showing, the optical drive is most likely bad.

  • Hard drive will not mount shows up in Disk Utility

    I have an external drive with a bootable OS X 10.6.8. I was in a transition between building up a SSD swapped drive. The SSD is installed in the CPU box but I have my old installation running from an external.
    I have several external hard drives. They are all Firewire. Some have USB 3.0 and or eSATA options but my MacMini only talks to Firewire and USB 2.0.
    I understand that you daisy chain Firewire drives and turn them on and off in sequence as they fall from the CPU box/case.
    Firewire is a power source. I run the external with the OS using an AC adapter but one Firewire drive is powered through Firewire.
    I have had as many as 4 external drives running along with the internal drive without a glitch while I was reorganizing files.
    Today I booted off the external drive. It was running fine. I turned on one Firewire drive (the one that runs on Firewire power). That drive stumbled. I recognized the sound when there is an interruption in power. This cause the external boot drive to stall. I had to force a reboot.
    Now the external boot drive will not boot up. It does not mount but Disk Utility sees it. The drive itself is bright and clear in Disk Utility but the partition (single) is faded out. I can run Verify and repair in DU. DU says it doesn't see anything to repair. It will not mount on its own or when I click the Mount button in DU. It does not produce an icon on the Desktop (because it is not mounting).
    I also have SpeedTools. But although it sees the drive I cannot do anything with it. None of its tools run more than a spli second before they fail.
    This drive has USB 3.0 and I see everything through USB that I see through Firewire. Connecting the other way did not get around the problem.
    Of course I will buy an AC adapter for every external drive and never run them using Firewire again but the horse is out of the barn.
    I have the original installation disks and could run the Archive and Install option but it would require physically swapping drives with the internal. I'd like to avoid it if possible. It is a MacMini and tedious.
    Any suggestions?

    I took the problematic hard drive and installed it in my Mac Mini so I could attempt a Safe Boot and then Archive and Install if necessary.
    Safe Mode didn't work. The drive produced the circle with a slash symbol.
    I reset the PRAM which was part of a list of steps to work through I found created by Apple Support.
    I was able to boot up to Verbose Mode and view the text of the boot process. I wrote it all down. I can answer questions about the content better than typing it all out exactly. It includes, "...journal magic is bad..." "...failed to open..." and ends with "...cannot mount root, errno = 19"
    I attempted Archive and Install however when it went to show what target drives were available it was a blank box and all buttons were grayed out.
    I rebooted and opened Disk Utility from the DVD. The drive appeared the same with the top main line bright and the partitioned volume faded. Still was unable to mount. I ran Verify and this time a red line of text appeared "Invalid content in Journal" and at the end I ran Repair. When running I could read line by line and at one point it showed "checking volume information" then the following line "Repairing volume" the following line "Rechecking volume" more line of checking then it ended with "The volume was repaired successfully."
    It still would not mount. I ran Verify again and again said "Invalid content in Journal" and this time it stopped midway saying "The volume was found corrupt and needs to be repaired. Error: This disk needs to be repaired. Click Repair Disk."
    I clicked Repair and it ended with The vol. was repaired successfully."
    Still unable to mount I began repeating Repair over and over. Each time it found something to repair and ended with a success message. After several more Repairs I tried Verify and it stopped midway saying to Repair the disk.
    Question: Does running Repair multiple times continue to correct bits and pieces little by little or is this a generic message and we should treat it as a problem Disk Utility cannot pinpoint and is just beating its head against the wall?
    The step by step instructions I downloaded mentioned running Repair more than once but it did not say that running it 20 times would erode some problems and eventually lead to a fully repaired disk (if the problem was something DU could take care of in the first place). At this point I have run Repair about 20 times total with a series of 10 back to back skipping Verify. I keep seeing the lines about invalid content in a journal and that it repaired something successfully. Yet I still cannot mount the disk.

  • My internal hard drive is not recognized by the leopard installer disk

    i just got my leopard delivered this morning, and have just put it in, every thing is going well, until it comes to the screen where you select the hard drive you want to install leopard on, and my internal hard drive does not show up, however other drives do (like my external hard drives and usb sticks).
    really hope someone can help! thanks

    I am having the same problem with my MBP with Leopard. I get a flashing question mark on startup, and have repaired/permissions and my startup disk doesn't show up. I reset PRAM, and then ran permissions again to no avail. If it really is Spotlight just indexing, Apple should tell us that in their technical documents. If anyone has any other solutions, that would be appreciated.

Maybe you are looking for