Internal MBP HD up as external - cant see Admin user

Woke up to my Macbook Pro a couple weeks ago sitting in a puddle of water. Fried. Went to Apple Store and had them take out internal hard drive and bought an external case for it. They said the HD looked ok and was worth a shot.
Today I finally found an iMac to hook it up to and after an extended wait the drive mounted and I was able to access it. Everything looks to be fine -woot- except that the Admin / Primary user account no longer shows up in the /Users/ folder (the 3 other user accounts do show up however).
What on earth? Has anyone ever seen / heard of such a thing? I am able to get files from the drive and view everything - but no admin account (which is of course where everything I need is). Any help GREATLY applreciated.

It's possible that the event resulted in the data loss from the drive. I suggest you see the following:
Basics of File Recovery
Files in Trash
If you simply put files in the Trash you can restore them by opening the Trash (left-click on the Trash icon) and drag the files from the Trash to your Desktop or other desired location. OS X also provides a short-cut to undo the last item moved to the Trash -press COMMAND-Z.
If you empty the Trash the files are gone. If a program does an immediate delete rather than moving files to the Trash, then the files are gone. Recovery is possible but you must not allow any additional writes to the hard drive - shut it down. When files are deleted only the directory entries, not the files themselves, is modified. The space occupied by the files has been returned to the system as available for storage, but the files are still on the drive. Writing to the drive will then eventually overwrite the space once occupied by the deleted files in which case the files are lost permanently. Also if you save a file over an existing file of the same name, then the old file is overwritten and cannot be recovered.
General File Recovery
If you stop using the drive it's possible to recover deleted files that have not been overwritten with recovery software such as Data Rescue II, File Salvage or TechTool Pro. Each of the preceding come on bootable CDs to enable usage without risk of writing more data to the hard drive.
The longer the hard drive remains in use and data are written to it, the greater the risk your deleted files will be overwritten.
Also visit The XLab FAQs and read the FAQ on Data Recovery.

Similar Messages

Cant see my user account

Guest is always showing on my log in page and im looking for the solution to remove this, then when im looking a way to remove the guest id turn off my user account cause i thought it will automatically directed to my account if i will turn on my imac, but when my imac restarted its showed only guest and cant find my user account to get in.
I dont know what im going to do now to get on my account, i tried the shift+option+control+scroll but theres no other account.
I am now using guest account to get online, but all of my files are in my account.
Anyone can help me to solve this problem?

Sir can you tell me the step to boot with option key?
Actually i did the command+r then theres a four option to do
Time machine
Reinstall OS X
Safari online
Disk Utily

Macintosh HD read only?? Cant see any user files???

Was working on a late 2009 iMac/OS 10.6 the other day with the oddest problem. Apparently my friend was updating to 10.6.7 and the iMac kernel panicked on him. It left the mac unable to boot. Booted from the DVD and ran disk utility, the drives index and b-tree catalogs were messed up and Disk Utility could not repair it. It told me to back up my files and reformat.
Ok not a problem there, I had a 3tb HDD hooked up and attempted to just cp -R the entire User folder from the Macintosh HD to the firewire hdd. Only took like a second to copy and what do you know there were no files in the folder at all. I guessed it had something to do with permissions being wierd since I was booted from the dvd so I installed 10.6 onto the firewire drive and booted off that. I can see the internal drive just fine, and Finder even says that the Users folder is 78gb, but his user folder is completely empty when you look into it. Its completely missing any sort of read permissions so you cant even view the files in the directory. I can see the top level username folder but nothing inside.
I tried to use chmod (and even sudo chmod) to change the entire folders permissions to 777 but terminal just tells me the drive is 'read only' and I cant change anything. My last step I did was basically used Disk Utility to make a dmg of his internal hd and copied it to the external since I had to format his internal drive and get things working. I did check Ignore Ownership On This Volume but that didnt help either. It wont even let me mess with the users permissions that the drive has at all, theyre all greyed out.
Now inside the dmg, I STILL have the same problem of having 78gb in his user folder that I cant do anything with at all, or even see for that matter.
Is there ANYTHING I can try that I havent yet that will allow me to get to his files? Its a bunch of ProTools stuff so its rather important to him. I guess worst case scenario I can try and restore the dmg to a drive or just mount it, and just look at it over the network with a Windows machine.. Would that work or is there something I can do to keep it all done on the Mac itself??

Just to clarify — have you actually tried to load tracks into your Shuffle, using either Autofill or by dragging music or playlists to it in the Source list?
I don't understand you characterize what you tried as a 'mistake'. I use my iPS in just that way and have changed back and forth several times, i.e., from all tracks to all data to mixes of both, with zero problems. It clearly works, and is far from 'useless' for carrying data.
The Shuffle has to be mounted and connected, of course, with iPod > Preferences available. Uncheck the "Disk Use" box and reset the slider, then click on Save. You will normally be able to Autofill from that point, as I did just last evening, slotting in the next 100-odd tracks of music.
OTOH, I have also seen your 'stuck' storage indication one time before. In my case it happened right after I tried using a friend's old laptop PC as a recharging station, which resulted in some other unusual indications from the Shuffle. I eventually had to Restore iot 'regain' the lost memory, and that is the same fix that has been reported as successful by others in this forum.
I can't quite follow your last para. on your own attempts at restoring. If you are doing it according to the Apple instructions and guidance (see the iPod Shuffle Support Page, among other sources) then that would have told you to use a current iPod Updater program and would have given you the exact steps to use.

PC w/ vista using AE as launchpoint- Cant see Admin Utility to set password

I have a HP laptop with VISTA. Wireless connection is ok with AE but running w/o a password. I want to set a password.
read some of the work arounds rescan or choose "other" retype the IP address and password "public" - no dice.
I'm about ready to toss AE in the trash because direct support ***** and so does FIREDOG who sold this to me - they want $76.
I trust that you guys can help especially because its the AE forum and crapo VISTA has been around a few moinths now.

Welcome to Discussions, DaneA!
I'm not sure if your problem is the same, so do either of these successfully concluded threads help?
linked HERE
or
linked HERE

Mountain Lion cant see my WD external Drive

I have just got my new MBP 15inch this week. I tried to mount a 1TB WD external Hard disk ... but my MBP (including the Disk Utility) cant see it. The external drive can be mounted perfectly on another MB 13 inch Mac OS Leopard machine.
I tried to plug/unplug ... use different USB port ... and i failed. After two days I tried again and only once my MBP 15 inch detected the drive !!!! It was very weird ! I copied some stiuff from the drive and unplugged it. When I tried to plug it again, the same problem appeard !!!
Help !

Thanks for the no-one-help. But for other poor buyers : Buy a new SS USB cable. It seems that Mountain Lion cant read the WD with the one-year old cable. Anyhow ... both are frustrating (Apple and WD )
get a new cable !

Hi. Im Tj.! I cant see chatters list in yahoo messenger chatroom. Im using MBP. Help me please.. Thanks

Hi. Im Tj.! I cant see chatters list in yahoo messenger chatroom. Im using MBP. Help me please.. Thanks

It's possible that when you dragged those "non-iTunes" files on the iPod to the Trash, you did not empty the Trash. At least on a Mac, if you do that, the files are still on the iPod's disk (not visible) taking up space as "Other." You may need to connect the iPod with disk mode enabled, then empty the Trash.
Or, if you don't mind erasing it completely, you can do a Restore on the iPod in iTunes. The Restore button is on the iPod's Summary screen in iTunes. That will erase the iPod, re-install its software, and set it to default settings. That should clear up the data under "Other."

Cant "see" external ADSL modem [D-link model DSL-500B]

Hi guys!
Im here in poor Brazil, and I just bought a new DSL-500B external ADSL modem, and I can make this machine turn to router, to stop login every time I turn on the computer.
The manual says that the IP is 192.168.254.254, but Firefox and Safari cant "see"... I ping, and cant find... I tracerout to a google site and the modem dont appear, its invisible!
Im properly conected on web... But I have this little problem...
I dont know what to do...
Please good people, help me!
Thanks,
Daniel
Brazil
iMac Mac OS X (10.3.9)

Nothing, mate...
Firefox can't establish a connection to the server at 192.168.1.1.
* The site could be temporarily unavailable or too busy. Try again in a few moments.
* If you are unable to load any pages, check your computer's network connection.
* If your computer or network is protected by a firewall or proxy, make sure that Firefox is permitted to access the Web.

Cant see messages in the External Definitions

I'm imporing following wsdl into XI. However I cant see messages and seems to be there is some error in wsdl. Would someone help me please?..
<?xml version="1.0" encoding="UTF-8"?>
<wsdl:definitions xmlns:apachesoap="http://xml.apache.org/xml-soap" xmlns:impl="urn:services.soap.a2z.com" xmlns:intf="urn:services.soap.a2z.com" xmlns:soapenc="http://schemas.xmlsoap.org/soap/encoding/" xmlns:wsdl="http://schemas.xmlsoap.org/wsdl/" xmlns:wsdlsoap="http://schemas.xmlsoap.org/wsdl/soap/" xmlns:xsd="http://www.w3.org/2001/XMLSchema" targetNamespace="urn:services.soap.a2z.com">
     <wsdl:types>
          <schema targetNamespace="http://xml.apache.org/xml-soap" xmlns="http://www.w3.org/2001/XMLSchema">
               <import namespace="http://schemas.xmlsoap.org/soap/encoding/"/>
               <complexType name="mapItem">
                    <sequence>
                         <element name="key" nillable="true" type="xsd:string"/>
                         <element name="value" nillable="true" type="xsd:string"/>
                    </sequence>
               </complexType>
               <complexType name="Map">
                    <sequence>
                         <element maxOccurs="unbounded" minOccurs="0" name="item" type="apachesoap:mapItem"/>
                    </sequence>
               </complexType>
          </schema>
     </wsdl:types>
     <wsdl:message name="exportGroupResponse">
          <wsdl:part name="exportGroupReturn" type="xsd:string"/>
     </wsdl:message>
     <wsdl:message name="importGroupRequest1">
          <wsdl:part name="in0" type="xsd:string"/>
     </wsdl:message>
     <wsdl:message name="importGroupResponse">
          <wsdl:part name="importGroupReturn" type="xsd:string"/>
     </wsdl:message>
     <wsdl:message name="importGroupResponse1">
          <wsdl:part name="importGroupReturn" type="xsd:string"/>
     </wsdl:message>
     <wsdl:message name="importGroupRequest">
          <wsdl:part name="in0" type="xsd:string"/>
          <wsdl:part name="in1" type="apachesoap:Map"/>
     </wsdl:message>
     <wsdl:message name="loadAdaptersResponse">
          <wsdl:part name="loadAdaptersReturn" type="xsd:string"/>
     </wsdl:message>
     <wsdl:message name="loadAdaptersRequest">
</wsdl:message>
     <wsdl:message name="exportAdapterResponse">
          <wsdl:part name="exportAdapterReturn" type="xsd:string"/>
     </wsdl:message>
     <wsdl:message name="importAdapterRequest1">
          <wsdl:part name="in0" type="xsd:string"/>
     </wsdl:message>
     <wsdl:message name="exportAdapterRequest">
          <wsdl:part name="in0" type="xsd:string"/>
     </wsdl:message>
     <wsdl:message name="importAdapterResponse">
          <wsdl:part name="importAdapterReturn" type="xsd:string"/>
     </wsdl:message>
     <wsdl:message name="exportGroupRequest">
          <wsdl:part name="in0" type="xsd:string"/>
     </wsdl:message>
     <wsdl:message name="importAdapterResponse1">
          <wsdl:part name="importAdapterReturn" type="xsd:string"/>
     </wsdl:message>
     <wsdl:message name="importAdapterRequest">
          <wsdl:part name="in0" type="xsd:string"/>
          <wsdl:part name="in1" type="apachesoap:Map"/>
     </wsdl:message>
     <wsdl:portType name="Adapter">
          <wsdl:operation name="importAdapter" parameterOrder="in0 in1">
               <wsdl:input name="importAdapterRequest" message="impl:importAdapterRequest"/>
               <wsdl:output name="importAdapterResponse" message="impl:importAdapterResponse"/>
          </wsdl:operation>
          <wsdl:operation name="importAdapter" parameterOrder="in0">
               <wsdl:input name="importAdapterRequest1" message="impl:importAdapterRequest1"/>
               <wsdl:output name="importAdapterResponse1" message="impl:importAdapterResponse1"/>
          </wsdl:operation>
          <wsdl:operation name="importGroup" parameterOrder="in0 in1">
               <wsdl:input name="importGroupRequest" message="impl:importGroupRequest"/>
               <wsdl:output name="importGroupResponse" message="impl:importGroupResponse"/>
          </wsdl:operation>
          <wsdl:operation name="importGroup" parameterOrder="in0">
               <wsdl:input name="importGroupRequest1" message="impl:importGroupRequest1"/>
               <wsdl:output name="importGroupResponse1" message="impl:importGroupResponse1"/>
          </wsdl:operation>
          <wsdl:operation name="exportAdapter" parameterOrder="in0">
               <wsdl:input name="exportAdapterRequest" message="impl:exportAdapterRequest"/>
               <wsdl:output name="exportAdapterResponse" message="impl:exportAdapterResponse"/>
          </wsdl:operation>
          <wsdl:operation name="exportGroup" parameterOrder="in0">
               <wsdl:input name="exportGroupRequest" message="impl:exportGroupRequest"/>
               <wsdl:output name="exportGroupResponse" message="impl:exportGroupResponse"/>
          </wsdl:operation>
          <wsdl:operation name="loadAdapters">
               <wsdl:input name="loadAdaptersRequest" message="impl:loadAdaptersRequest"/>
               <wsdl:output name="loadAdaptersResponse" message="impl:loadAdaptersResponse"/>
          </wsdl:operation>
     </wsdl:portType>
     <wsdl:binding name="AdapterServiceSoapBinding" type="impl:Adapter">
          <wsdlsoap:binding style="rpc" transport="http://schemas.xmlsoap.org/soap/http"/>
          <wsdl:operation name="importAdapter">
               <wsdlsoap:operation/>
               <wsdl:input>
                    <wsdlsoap:body use="encoded" encodingStyle="http://schemas.xmlsoap.org/soap/encoding/" namespace="urn:services.soap.a2z.com"/>
               </wsdl:input>
               <wsdl:output>
                    <wsdlsoap:body use="encoded" encodingStyle="http://schemas.xmlsoap.org/soap/encoding/" namespace="urn:services.soap.a2z.com"/>
               </wsdl:output>
          </wsdl:operation>
          <wsdl:operation name="importAdapter">
               <wsdlsoap:operation/>
               <wsdl:input>
                    <wsdlsoap:body use="encoded" encodingStyle="http://schemas.xmlsoap.org/soap/encoding/" namespace="urn:services.soap.a2z.com"/>
               </wsdl:input>
               <wsdl:output>
                    <wsdlsoap:body use="encoded" encodingStyle="http://schemas.xmlsoap.org/soap/encoding/" namespace="urn:services.soap.a2z.com"/>
               </wsdl:output>
          </wsdl:operation>
          <wsdl:operation name="importGroup">
               <wsdlsoap:operation/>
               <wsdl:input>
                    <wsdlsoap:body use="encoded" encodingStyle="http://schemas.xmlsoap.org/soap/encoding/" namespace="urn:services.soap.a2z.com"/>
               </wsdl:input>
               <wsdl:output>
                    <wsdlsoap:body use="encoded" encodingStyle="http://schemas.xmlsoap.org/soap/encoding/" namespace="urn:services.soap.a2z.com"/>
               </wsdl:output>
          </wsdl:operation>
          <wsdl:operation name="importGroup">
               <wsdlsoap:operation/>
               <wsdl:input>
                    <wsdlsoap:body use="encoded" encodingStyle="http://schemas.xmlsoap.org/soap/encoding/" namespace="urn:services.soap.a2z.com"/>
               </wsdl:input>
               <wsdl:output>
                    <wsdlsoap:body use="encoded" encodingStyle="http://schemas.xmlsoap.org/soap/encoding/" namespace="urn:services.soap.a2z.com"/>
               </wsdl:output>
          </wsdl:operation>
          <wsdl:operation name="exportAdapter">
               <wsdlsoap:operation/>
               <wsdl:input>
                    <wsdlsoap:body use="encoded" encodingStyle="http://schemas.xmlsoap.org/soap/encoding/" namespace="urn:services.soap.a2z.com"/>
               </wsdl:input>
               <wsdl:output>
                    <wsdlsoap:body use="encoded" encodingStyle="http://schemas.xmlsoap.org/soap/encoding/" namespace="urn:services.soap.a2z.com"/>
               </wsdl:output>
          </wsdl:operation>
          <wsdl:operation name="exportGroup">
               <wsdlsoap:operation/>
               <wsdl:input>
                    <wsdlsoap:body use="encoded" encodingStyle="http://schemas.xmlsoap.org/soap/encoding/" namespace="urn:services.soap.a2z.com"/>
               </wsdl:input>
               <wsdl:output>
                    <wsdlsoap:body use="encoded" encodingStyle="http://schemas.xmlsoap.org/soap/encoding/" namespace="urn:services.soap.a2z.com"/>
               </wsdl:output>
          </wsdl:operation>
          <wsdl:operation name="loadAdapters">
               <wsdlsoap:operation/>
               <wsdl:input>
                    <wsdlsoap:body use="encoded" encodingStyle="http://schemas.xmlsoap.org/soap/encoding/" namespace="urn:services.soap.a2z.com"/>
               </wsdl:input>
               <wsdl:output>
                    <wsdlsoap:body use="encoded" encodingStyle="http://schemas.xmlsoap.org/soap/encoding/" namespace="urn:services.soap.a2z.com"/>
               </wsdl:output>
          </wsdl:operation>
     </wsdl:binding>
     <wsdl:service name="AdapterService">
          <wsdl:port name="AdapterService" binding="impl:AdapterServiceSoapBinding">
               <wsdlsoap:address location="http://vn15:8000/soap/services/AdapterService"/>
          </wsdl:port>
     </wsdl:service>
</wsdl:definitions>

Hi S T,
in the WSDL there occurs the situation that there are in one prtType multiple operations with the same name (e.g. portType "Adapter" contains two definitions for operation with name "importAdapter". Indeed, the original <a href="http://www.w3.org/TR/wsdl">WSDL specification</a> seems to allow this. However, in <a href="http://www.ws-i.org/Profiles/BasicProfile-1.0-2004-04-16.html">WS-I</a> it is forbidden (see R2304).
Therefore, the Integration Builder does not consider this document to be valid WSDL. This is a little bit tragic, as the portType definitions are not considered by the following steps anyway. A simple workaround would be to delete everything behind the message definitions.
Greetings Stephan

Cant see external Hard Drive connected to TC

Hey Guys
Love my TC but still cant get it to work as I want. I will list my challenges seperatley.
The first one is I have a hard drive connected by USB but I cant see it in Finder? I can see everything on my TC but not the connected HD.
Thanks in Advance
AC
(Its the latest TC with latest software)

What Bob suggested should work.
You can also plug the USB drive into a Mac.. Mac OS can read NTFS but not write to it. You could then copy the files to the TC. My experience is Mac reads NTFS very slowly..
You do want to get the PC working I think, by ethernet to the TC and copy the files.
If this is just temporary that is fine.. using the TC for a data store and mixing with Time Machine is not such a great idea.
IMHO USB drives are cheap.. go and buy a new one. So you can copy the files direct from one disk plugged into your computer to the drive correctly connected to the TC or to the Mac.. Keep the old USB as a backup or format it and use it for something else.

IPsec over GRE not coming up, cant see why, debug inc...

Hi all,
Rattling my brains here, as far as i can see everything is fine, it should be working, but for some reason its not, and i cant see anything in the debug thats hinting to the reason why, can anyone help me out with this?
im normally good at this stuff, but this time its got me!
the hub config works with many 3 other spokes configured in the same way!
Thanks for any help guys
SPOKE
crypto isakmp policy 10
encr aes 256
authentication pre-share
group 5
crypto isakmp key xxxxxxxxxxxxxxxxx address xxx.xxx.xxx.xx3
crypto isakmp keepalive 10 4
crypto isakmp nat keepalive 30
crypto ipsec transform-set AES-256_SHA esp-aes 256 esp-sha-hmac
mode transport
crypto ipsec transform-set AES-SHA esp-aes esp-sha-hmac
mode transport
crypto ipsec profile GRE_TUNNEL
set transform-set AES-SHA
archive
log config
hidekeys
ip ssh version 2
interface Tunnel1
bandwidth 100000
ip address 192.168.100.103 255.255.255.0
no ip redirects
ip mtu 1440
ip nhrp authentication xxxxxx
ip nhrp map 192.168.100.1 xxx.xxx.xxx.xx3
ip nhrp map multicast xxx.xxx.xxx.xx3
ip nhrp network-id 100
ip nhrp holdtime 450
ip nhrp nhs 192.168.100.1
ip tcp adjust-mss 1360
qos pre-classify
tunnel source Vlan100
tunnel mode gre multipoint
tunnel key 100
tunnel protection ipsec profile GRE_TUNNEL
interface ATM0
no ip address
shutdown
no atm ilmi-keepalive
pvc 1/50
dialer pool-member 1
protocol ppp dialer
dsl operating-mode auto
interface FastEthernet0
switchport access vlan 100
interface FastEthernet1
switchport access vlan 103
interface FastEthernet2
switchport access vlan 103
interface FastEthernet3
switchport access vlan 103
interface Vlan1
no ip address
ip virtual-reassembly
ip tcp adjust-mss 1452
shutdown
interface Vlan100
ip address dhcp
ip nbar protocol-discovery
ip nat outside
ip inspect UserTraffic out
ip virtual-reassembly
interface Vlan103
ip address 192.168.103.254 255.255.255.0
ip nat inside
ip virtual-reassembly
router eigrp 100
network 192.168.100.0
network 192.168.103.0
auto-summary
no ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 192.168.1.254
no ip http server
no ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip nat inside source list OUTBOUND interface Vlan100 overload
ip access-list extended INBOUND
deny   tcp any any eq 22
deny   tcp any any eq telnet
permit ip any any
deny   ip any any
ip access-list extended OUTBOUND
permit ip any any
deny   ip any any
HUB
crypto isakmp policy 10
encr 3des
authentication pre-share
group 2
crypto isakmp policy 15
encr 3des
authentication pre-share
crypto isakmp policy 20
encr 3des
authentication pre-share
group 2
lifetime 7800
crypto isakmp policy 50
encr aes 256
authentication pre-share
group 5
crypto isakmp key xxxxxxxxxx address 0.0.0.0 0.0.0.0
crypto isakmp fragmentation
crypto isakmp keepalive 10 4
crypto isakmp nat keepalive 30
crypto ipsec security-association idle-time 7800
crypto ipsec transform-set AES-SHA esp-aes esp-sha-hmac
mode transport
crypto ipsec transform-set AES_MD5_TUNNEL esp-aes 256 esp-md5-hmac
crypto ipsec profile DataTunnels
set transform-set AES-SHA
interface Tunnel1
bandwidth 1000
ip address 192.168.100.1 255.255.255.0
no ip redirects
ip mtu 1400
no ip next-hop-self eigrp 100
ip nhrp authentication xxxxxxxxxxx
ip nhrp map multicast dynamic
ip nhrp network-id 100
ip nhrp holdtime 450
ip tcp adjust-mss 1360
no ip split-horizon eigrp 100
qos pre-classify
tunnel source Dialer1
tunnel mode gre multipoint
tunnel key 100
tunnel protection ipsec profile DataTunnels
interface ATM0
no ip address
no atm ilmi-keepalive
pvc 1/50
dialer pool-member 1
protocol ppp dialer
interface FastEthernet0
description INTERNAL LAN
switchport access vlan 201
interface FastEthernet1
switchport access vlan 201
interface FastEthernet2
switchport access vlan 201
interface Vlan201
ip address 192.168.201.254 255.255.255.252
ip nat inside
ip virtual-reassembly
interface Dialer1
ip address negotiated
ip access-group INBOUND in
ip nbar protocol-discovery
ip nat outside
ip inspect UserTraffic out
ip virtual-reassembly
encapsulation ppp
ip tcp adjust-mss 1300
load-interval 30
no cdp enable
router eigrp 100
network 192.168.100.0
network 192.168.201.0
redistribute static
router nhrp
router odr
ip nat inside source list OUTBOUND interface Dialer1 overload
ip route 0.0.0.0 0.0.0.0 Dialer1
ip access-list extended INBOUND
permit ip 192.168.250.0 0.0.0.15 192.168.101.0 0.0.0.255
deny   tcp any any eq 22
deny   tcp any any eq telnet
permit tcp any host xxx.xxx.xxx.xx3 eq www
permit tcp any host xxx.xxx.xxx.xx3 eq 443
permit tcp any host xxx.xxx.xxx.xx3 eq smtp
permit udp any host xxx.xxx.xxx.xx3 eq isakmp
permit esp any host xxx.xxx.xxx.xx3
permit ahp any host xxx.xxx.xxx.xx3
permit udp any host xxx.xxx.xxx.xx3 eq non500-isakmp
deny   ip any any
permit ip any any
ip access-list extended OUTBOUND
permit tcp any any eq smtp
permit tcp any any eq 443
permit ip 192.168.201.0 0.0.0.255 any
deny   ip any any
DEBUG
CWT-DATA#sh ip nhrp detail
192.168.100.1/32 via 192.168.100.1, Tunnel1 created 1w5d, never expire
Type: static, Flags: used
NBMA address: xxx.xxx.xxx.xx3
CWT-DATA#sh crypto isakmp sa
IPv4 Crypto ISAKMP SA
dst             src             state          conn-id slot status
xxx.xxx.xxx.xx3     192.168.1.7     MM_NO_STATE       2821    0 ACTIVE (deleted)
Jul 4 12:53:35.551: ISAKMP:(2822):Sending an IKE IPv4 Packet.
CWT-DATA#
Jul 4 12:53:45.553: ISAKMP:(2822): retransmitting phase 1 MM_KEY_EXCH...
Jul 4 12:53:45.553: ISAKMP:(2822):peer does not do paranoid keepalives.
Jul 4 12:53:45.553: ISAKMP:(2822):deleting SA reason "Death by retransmission P1" state (I) MM_KEY_EXCH (peer xxx.xxx.xxx.xx3)
Jul 4 12:53:45.553: ISAKMP:(2822):deleting SA reason "Death by retransmission P1" state (I) MM_KEY_EXCH (peer xxx.xxx.xxx.xx3)
Jul 4 12:53:45.553: ISAKMP: Unlocking peer struct 0x835CCCE8 for isadb_mark_sa_deleted(), count 0
Jul 4 12:53:45.553: ISAKMP: Deleting peer node by peer_reap for xxx.xxx.xxx.xx3: 835CCCE8
Jul 4 12:53:45.553: ISAKMP:(2822):deleting node -32418685 error FALSE reason "IKE deleted"
Jul 4 12:53:45.553: ISAKMP:(2822):deleting node 2092182627 error FALSE reason "IKE deleted"
Jul 4 12:53:45.553: ISAKMP:(2822):Input = IKE_MESG_INTERNAL, IKE_PHASE1_DEL
Jul 4 12:53:45.553: ISAKMP:(2822):Old State = IKE_I_MM5 New State = IKE_DEST_SA
Jul 4 12:53:45.585: ISAKMP:(0): SA request profile is (NULL)
Jul 4 12:53:45.585: ISAKMP: Created a peer struct for xxx.xxx.xxx.xx3, peer port 500
Jul 4 12:53:45.585: ISAKMP: New peer created peer = 0x835CCCE8 peer_handle = 0x800025C0
Jul 4 12:53:45.585: ISAKMP: Locking peer struct 0x835CCCE8, refcount 1 for isakmp_initiator
Jul 4 12:53:45.585: ISAKMP: local port 500, remote port 500
Jul 4 12:53:45.585: ISAKMP: set new node 0 to QM_IDLE
Jul 4 12:53:45.585: ISAKMP: Find a dup sa in the avl tree during calling isadb_insert sa = 8333DA70
Jul 4 12:53:45.585: ISAKMP:(0):Can not start Aggressive mode, trying Main mode.
Jul 4 12:53:45.585: ISAKMP:(0):found peer pre-shared key matching xxx.xxx.xxx.xx3
Jul 4 12:53:45.585: ISAKMP:(0): constructed NAT-T vendor-rfc3947 ID
Jul 4 12:53:45.585: ISAKMP:(0): constructed NAT-T vendor-07 ID
Jul 4 12:53:45.585: ISAKMP:(0): constructed NAT-T vendor-03 ID
Jul 4 12:53:45.585: ISAKMP:(0): constructed NAT-T vendor-02 ID
Jul 4 12:53:45.585: ISAKMP:(0):Input = IKE_MESG_FROM_IPSEC, IKE_SA_REQ_MM
Jul 4 12:53:45.585: ISAKMP:(0):Old State = IKE_READY New State = IKE_I_MM1
Jul 4 12:53:45.589: ISAKMP:(0): beginning Main Mode exchange
Jul 4 12:53:45.589: ISAKMP:(0): sending packet to xxx.xxx.xxx.xx3 my_port 500 peer_port 500 (I) MM_NO_STATE
Jul 4 12:53:45.589: ISAKMP:(0):Sending an IKE IPv4 Packet.
Jul 4 12:53:45.653: ISAKMP (0:0): received packet from xxx.xxx.xxx.xx3 dport 500 sport 500 Global (I) MM_NO_STATE
Jul 4 12:53:45.653: ISAKMP:(0):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
Jul 4 12:53:45.653: ISAKMP:(0):Old State = IKE_I_MM1 New State = IKE_I_MM2
Jul 4 12:53:45.653: ISAKMP:(0): processing SA payload. message ID = 0
Jul 4 12:53:45.653: ISAKMP:(0): processing vendor id payload
Jul 4 12:53:45.653: ISAKMP:(0): vendor ID seems Unity/DPD but major 69 mismatch
Jul 4 12:53:45.653: ISAKMP (0:0): vendor ID is NAT-T RFC 3947
Jul 4 12:53:45.653: ISAKMP:(0):found peer pre-shared key matching xxx.xxx.xxx.xx3
Jul 4 12:53:45.653: ISAKMP:(0): local preshared key found
Jul 4 12:53:45.653: ISAKMP : Scanning profiles for xauth ...
Jul 4 12:53:45.653: ISAKMP:(0):Checking ISAKMP transform 1 against priority 10 policy
Jul 4 12:53:45.653: ISAKMP:      encryption AES-CBC
Jul 4 12:53:45.653: ISAKMP:      keylength of 256
Jul 4 12:53:45.653: ISAKMP:      hash SHA
Jul 4 12:53:45.653: ISAKMP:      default group 5
Jul 4 12:53:45.653: ISAKMP:      auth pre-share
Jul 4 12:53:45.653: ISAKMP:      life type in seconds
Jul 4 12:53:45.653: ISAKMP:      life duration (VPI) of 0x0 0x1 0x51 0x80
Jul 4 12:53:45.657: ISAKMP:(0):atts are acceptable. Next payload is 0
Jul 4 12:53:45.657: ISAKMP:(0):Acceptable atts:actual life: 0
Jul 4 12:53:45.657: ISAKMP:(0):Acceptable atts:life: 0
Jul 4 12:53:45.657: ISAKMP:(0):Fill atts in sa vpi_length:4
Jul 4 12:53:45.657: ISAKMP:(0):Fill atts in sa life_in_seconds:86400
Jul 4 12:53:45.657: ISAKMP:(0):Returning Actual lifetime: 86400
Jul 4 12:53:45.657: ISAKMP:(0)::Started lifetime timer: 86400.
Jul 4 12:53:45.657: ISAKMP:(0): processing vendor id payload
Jul 4 12:53:45.657: ISAKMP:(0): vendor ID seems Unity/DPD but major 69 mismatch
Jul 4 12:53:45.657: ISAKMP (0:0): vendor ID is NAT-T RFC 3947
Jul 4 12:53:45.657: ISAKMP:(0):Input = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
Jul 4 12:53:45.657: ISAKMP:(0):Old State = IKE_I_MM2 New State = IKE_I_MM2
Jul 4 12:53:45.657: ISAKMP:(0): sending packet to xxx.xxx.xxx.xx3 my_port 500 peer_port 500 (I) MM_SA_SETUP
Jul 4 12:53:45.657: ISAKMP:(0):Sending an IKE IPv4 Packet.
Jul 4 12:53:45.661: ISAKMP:(0):Input = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
CWT-DATA#
Jul 4 12:53:45.661: ISAKMP:(0):Old State = IKE_I_MM2 New State = IKE_I_MM3
Jul 4 12:53:45.813: ISAKMP (0:0): received packet from xxx.xxx.xxx.xx3 dport 500 sport 500 Global (I) MM_SA_SETUP
Jul 4 12:53:45.817: ISAKMP:(0):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
Jul 4 12:53:45.817: ISAKMP:(0):Old State = IKE_I_MM3 New State = IKE_I_MM4
Jul 4 12:53:45.817: ISAKMP:(0): processing KE payload. message ID = 0
Jul 4 12:53:45.989: ISAKMP:(0): processing NONCE payload. message ID = 0
Jul 4 12:53:45.989: ISAKMP:(0):found peer pre-shared key matching xxx.xxx.xxx.xx3
Jul 4 12:53:45.993: ISAKMP:(2823): processing vendor id payload
Jul 4 12:53:45.993: ISAKMP:(2823): vendor ID is Unity
Jul 4 12:53:45.993: ISAKMP:(2823): processing vendor id payload
Jul 4 12:53:45.993: ISAKMP:(2823): vendor ID is DPD
Jul 4 12:53:45.993: ISAKMP:(2823): processing vendor id payload
Jul 4 12:53:45.993: ISAKMP:(2823): speaking to another IOS box!
Jul 4 12:53:45.993: ISAKMP:received payload type 20
Jul 4 12:53:45.993: ISAKMP (0:2823): NAT found, the node inside NAT
Jul 4 12:53:45.993: ISAKMP:received payload type 20
Jul 4 12:53:45.993: ISAKMP:(2823):Input = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
Jul 4 12:53:45.993: ISAKMP:(2823):Old State = IKE_I_MM4 New State = IKE_I_MM4
Jul 4 12:53:45.993: ISAKMP:(2823):Send initial contact
Jul 4 12:53:45.993: ISAKMP:(2823):SA is doing pre-shared key authentication using id type ID_IPV4_ADDR
Jul 4 12:53:45.993: ISAKMP (0:2823): ID payload
        next-payload : 8
        type         : 1
        address      : 192.168.1.7
        protocol     : 17
        port         : 0
        length       : 12
Jul 4 12:53:45.993: ISAKMP:(2823):Total payload length: 12
Jul 4 12:53:45.997: ISAKMP:(2823): sending packet to xxx.xxx.xxx.xx3 my_port 4500 peer_port 4500 (I) MM_KEY_EXCH
Jul 4 12:53:45.997: ISAKMP:(2823):Sending an IKE IPv4 Packet.
Jul 4 12:53:45.997: ISAKMP:(2823):Input = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
CWT-DATA#
Jul 4 12:53:45.997: ISAKMP:(2823):Old State = IKE_I_MM4 New State = IKE_I_MM5
CWT-DATA#
Jul 4 12:53:55.794: ISAKMP (0:2823): received packet from xxx.xxx.xxx.xx3 dport 500 sport 500 Global (I) MM_KEY_EXCH
Jul 4 12:53:55.794: ISAKMP:(2823): phase 1 packet is a duplicate of a previous packet.
Jul 4 12:53:55.794: ISAKMP:(2823): retransmitting due to retransmit phase 1
Jul 4 12:53:56.294: ISAKMP:(2823): retransmitting phase 1 MM_KEY_EXCH...
Jul 4 12:53:56.294: ISAKMP (0:2823): incrementing error counter on sa, attempt 1 of 5: retransmit phase 1
Jul 4 12:53:56.294: ISAKMP:(2823): retransmitting phase 1 MM_KEY_EXCH
Jul 4 12:53:56.294: ISAKMP:(2823): sending packet to xxx.xxx.xxx.xx3 my_port 4500 peer_port 4500 (I) MM_KEY_EXCH
CWT-DATA#
Jul 4 12:53:56.294: ISAKMP:(2823):Sending an IKE IPv4 Packet.
CWT-DATA#
Jul 4 12:54:05.795: ISAKMP (0:2823): received packet from xxx.xxx.xxx.xx3 dport 500 sport 500 Global (I) MM_KEY_EXCH
Jul 4 12:54:05.795: ISAKMP:(2823): phase 1 packet is a duplicate of a previous packet.
Jul 4 12:54:05.795: ISAKMP:(2823): retransmitting due to retransmit phase 1
Jul 4 12:54:06.295: ISAKMP:(2823): retransmitting phase 1 MM_KEY_EXCH...
Jul 4 12:54:06.295: ISAKMP (0:2823): incrementing error counter on sa, attempt 2 of 5: retransmit phase 1
Jul 4 12:54:06.295: ISAKMP:(2823): retransmitting phase 1 MM_KEY_EXCH
Jul 4 12:54:06.295: ISAKMP:(2823): sending packet to xxx.xxx.xxx.xx3 my_port 4500 peer_port 4500 (I) MM_KEY_EXCH
CWT-DATA#
Jul 4 12:54:06.295: ISAKMP:(2823):Sending an IKE IPv4 Packet.
CWT-DATA#
Jul 4 12:54:15.797: ISAKMP (0:2823): received packet from xxx.xxx.xxx.xx3 dport 500 sport 500 Global (I) MM_KEY_EXCH
Jul 4 12:54:15.797: ISAKMP:(2823): phase 1 packet is a duplicate of a previous packet.
Jul 4 12:54:15.797: ISAKMP:(2823): retransmitting due to retransmit phase 1
Jul 4 12:54:16.297: ISAKMP:(2823): retransmitting phase 1 MM_KEY_EXCH...
Jul 4 12:54:16.297: ISAKMP (0:2823): incrementing error counter on sa, attempt 3 of 5: retransmit phase 1
Jul 4 12:54:16.297: ISAKMP:(2823): retransmitting phase 1 MM_KEY_EXCH
Jul 4 12:54:16.297: ISAKMP:(2823): sending packet to xxx.xxx.xxx.xx3 my_port 4500 peer_port 4500 (I) MM_KEY_EXCH
CWT-DATA#
Jul 4 12:54:16.297: ISAKMP:(2823):Sending an IKE IPv4 Packet.
CWT-DATA#
Jul 4 12:54:19.537: ISAKMP: set new node 0 to QM_IDLE
Jul 4 12:54:19.537: ISAKMP:(2823):SA is still budding. Attached new ipsec request to it. (local 192.168.1.7, remote xxx.xxx.xxx.xx3)
Jul 4 12:54:19.537: ISAKMP: Error while processing SA request: Failed to initialize SA
Jul 4 12:54:19.537: ISAKMP: Error while processing KMI message 0, error 2.
CWT-DATA#
Jul 4 12:54:25.794: ISAKMP (0:2823): received packet from xxx.xxx.xxx.xx3 dport 500 sport 500 Global (I) MM_KEY_EXCH
Jul 4 12:54:25.798: ISAKMP:(2823): phase 1 packet is a duplicate of a previous packet.
Jul 4 12:54:25.798: ISAKMP:(2823): retransmitting due to retransmit phase 1
Jul 4 12:54:26.298: ISAKMP:(2823): retransmitting phase 1 MM_KEY_EXCH...
Jul 4 12:54:26.298: ISAKMP (0:2823): incrementing error counter on sa, attempt 4 of 5: retransmit phase 1
Jul 4 12:54:26.298: ISAKMP:(2823): retransmitting phase 1 MM_KEY_EXCH
Jul 4 12:54:26.298: ISAKMP:(2823): sending packet to xxx.xxx.xxx.xx3 my_port 4500 peer_port 4500 (I) MM_KEY_EXCH
CWT-DATA#
Jul 4 12:54:26.298: ISAKMP:(2823):Sending an IKE IPv4 Packet.
CWT-DATA#
Jul 4 12:54:35.555: ISAKMP:(2822):purging node -32418685
Jul 4 12:54:35.555: ISAKMP:(2822):purging node 2092182627
Jul 4 12:54:35.795: ISAKMP (0:2823): received packet from xxx.xxx.xxx.xx3 dport 500 sport 500 Global (I) MM_KEY_EXCH
Jul 4 12:54:35.795: ISAKMP:(2823): phase 1 packet is a duplicate of a previous packet.
Jul 4 12:54:35.795: ISAKMP:(2823): retransmitting due to retransmit phase 1
Jul 4 12:54:36.295: ISAKMP:(2823): retransmitting phase 1 MM_KEY_EXCH...
Jul 4 12:54:36.295: ISAKMP (0:2823): incrementing error counter on sa, attempt 5 of 5: retransmit phase 1
Jul 4 12:54:36.295: ISAKMP:(2823): retransmitting phase 1 MM_KEY_EXCH
CWT-DATA#
Jul 4 12:54:36.295: ISAKMP:(2823): sending packet to xxx.xxx.xxx.xx3 my_port 4500 peer_port 4500 (I) MM_KEY_EXCH
Jul 4 12:54:36.295: ISAKMP:(2823):Sending an IKE IPv4 Packet.
CWT-DATA#no debug all
All possible debugging has been turned off

heres the hub debug
CWCH#
*Jul 5 11:58:16.208: ISAKMP: set new node 1382820308 to QM_IDLE
*Jul 5 11:58:16.208: ISAKMP:(2116): sending packet to xxx.xxx.xxx.10 my_port 4500 peer_port 4500 (R) QM_IDLE
*Jul 5 11:58:16.208: ISAKMP:(2116):Sending an IKE IPv4 Packet.
*Jul 5 11:58:16.208: ISAKMP:(2116):purging node 1382820308
*Jul 5 11:58:16.208: ISAKMP:(2116):Input = IKE_MESG_FROM_IPSEC, IKE_PHASE2_DEL
*Jul 5 11:58:16.208: ISAKMP:(2116):Old State = IKE_P1_COMPLETE New State = IKE_P1_COMPLETE
*Jul 5 12:02:47.504: ISAKMP (2120): received packet from xxx.xxx.xxx.10 dport 4500 sport 62560 Global (R) QM_IDLE
*Jul 5 12:02:47.504: ISAKMP: set new node -146383553 to QM_IDLE
*Jul 5 12:02:47.504: ISAKMP:(2120): processing HASH payload. message ID = -146383553
*Jul 5 12:02:47.504: ISAKMP:(2120): processing NOTIFY DPD/R_U_THERE protocol 1
        spi 0, message ID = -146383553, sa = 0x854A7094
*Jul 5 12:02:47.504: ISAKMP:(2120):deleting node -146383553 error FALSE reason "Informational (in) state 1"
*Jul 5 12:02:47.504: ISAKMP:(2120):Input = IKE_MESG_FROM_PEER, IKE_INFO_NOTIFY
*Jul 5 12:02:47.504: ISAKMP:(2120):Old State = IKE_P1_COMPLETE New State = IKE_P1_COMPLETE
*Jul 5 12:02:47.504: ISAKMP:(2120):DPD/R_U_THERE received from peer xxx.xxx.xxx.10, sequence 0x63A1AE3C
*Jul 5 12:02:47.504: ISAKMP: set new node -1398198787 to QM_IDLE
*Jul 5 12:02:47.504: ISAKMP:(2120):Sending NOTIFY DPD/R_U_THERE_ACK protocol 1
        spi 2242383312, message ID = -1398198787
*Jul 5 12:02:47.504: ISAKMP:(2120): seq. no 0x63A1AE3C
*Jul 5 12:02:47.504: ISAKMP:(2120): sending packet to xxx.xxx.xxx.10 my_port 4500 peer_port 62560 (R) QM_IDLE
*Jul 5 12:02:47.504: ISAKMP:(2120):Sending an IKE IPv4 Packet.
CWCH#
*Jul 5 12:02:47.504: ISAKMP:(2120):purging node -1398198787
*Jul 5 12:02:47.504: ISAKMP:(2120):Input = IKE_MESG_FROM_PEER, IKE_MESG_KEEP_ALIVE
*Jul 5 12:02:47.504: ISAKMP:(2120):Old State = IKE_P1_COMPLETE New State = IKE_P1_COMPLETE
CWCH#
*Jul 5 12:02:52.516: ISAKMP (2120): received packet from xxx.xxx.xxx.10 dport 4500 sport 62560 Global (R) QM_IDLE
*Jul 5 12:02:52.516: ISAKMP: set new node -459292560 to QM_IDLE
*Jul 5 12:02:52.516: ISAKMP:(2120): processing HASH payload. message ID = -459292560
*Jul 5 12:02:52.516: ISAKMP:(2120): processing NOTIFY DPD/R_U_THERE protocol 1
        spi 0, message ID = -459292560, sa = 0x854A7094
*Jul 5 12:02:52.516: ISAKMP:(2120):deleting node -459292560 error FALSE reason "Informational (in) state 1"
*Jul 5 12:02:52.516: ISAKMP:(2120):Input = IKE_MESG_FROM_PEER, IKE_INFO_NOTIFY
*Jul 5 12:02:52.516: ISAKMP:(2120):Old State = IKE_P1_COMPLETE New State = IKE_P1_COMPLETE
*Jul 5 12:02:52.516: ISAKMP:(2120):DPD/R_U_THERE received from peer xxx.xxx.xxx.10, sequence 0x63A1AE3D
*Jul 5 12:02:52.516: ISAKMP: set new node -1245354522 to QM_IDLE
*Jul 5 12:02:52.516: ISAKMP:(2120):Sending NOTIFY DPD/R_U_THERE_ACK protocol 1
        spi 2242383312, message ID = -1245354522
*Jul 5 12:02:52.516: ISAKMP:(2120): seq. no 0x63A1AE3D
*Jul 5 12:02:52.516: ISAKMP:(2120): sending packet to xxx.xxx.xxx.10 my_port 4500 peer_port 62560 (R) QM_IDLE
*Jul 5 12:02:52.516: ISAKMP:(2120):Sending an IKE IPv4 Packet.
CWCH#
*Jul 5 12:02:52.516: ISAKMP:(2120):purging node -1245354522
*Jul 5 12:02:52.520: ISAKMP:(2120):Input = IKE_MESG_FROM_PEER, IKE_MESG_KEEP_ALIVE
*Jul 5 12:02:52.520: ISAKMP:(2120):Old State = IKE_P1_COMPLETE New State = IKE_P1_COMPLETE
CWCH#
*Jul 5 12:02:55.636: ISAKMP:(2119):Input = IKE_MESG_FROM_PEER, IKE_MESG_KEEP_ALIVE
*Jul 5 12:02:55.636: ISAKMP:(2119):Old State = IKE_P1_COMPLETE New State = IKE_P1_COMPLETE
*Jul 5 12:02:55.656: ISAKMP:(2119):purging node 926310294
CWCH#
*Jul 5 12:02:58.000: ISAKMP (2120): received packet from xxx.xxx.xxx.10 dport 4500 sport 62560 Global (R) QM_IDLE
*Jul 5 12:02:58.000: ISAKMP: set new node -1957053939 to QM_IDLE
*Jul 5 12:02:58.000: ISAKMP:(2120): processing HASH payload. message ID = -1957053939
*Jul 5 12:02:58.000: ISAKMP:(2120): processing NOTIFY DPD/R_U_THERE protocol 1
        spi 0, message ID = -1957053939, sa = 0x854A7094
*Jul 5 12:02:58.000: ISAKMP:(2120):deleting node -1957053939 error FALSE reason "Informational (in) state 1"
*Jul 5 12:02:58.000: ISAKMP:(2120):Input = IKE_MESG_FROM_PEER, IKE_INFO_NOTIFY
*Jul 5 12:02:58.000: ISAKMP:(2120):Old State = IKE_P1_COMPLETE New State = IKE_P1_COMPLETE
*Jul 5 12:02:58.000: ISAKMP:(2120):DPD/R_U_THERE received from peer xxx.xxx.xxx.10, sequence 0x63A1AE3E
*Jul 5 12:02:58.000: ISAKMP: set new node -1198504167 to QM_IDLE
*Jul 5 12:02:58.004: ISAKMP:(2120):Sending NOTIFY DPD/R_U_THERE_ACK protocol 1
        spi 2242383312, message ID = -1198504167
*Jul 5 12:02:58.004: ISAKMP:(2120): seq. no 0x63A1AE3E
*Jul 5 12:02:58.004: ISAKMP:(2120): sending packet to xxx.xxx.xxx.10 my_port 4500 peer_port 62560 (R) QM_IDLE
*Jul 5 12:02:58.004: ISAKMP:(2120):Sending an IKE IPv4 Packet.
CWCH#
*Jul 5 12:02:58.004: ISAKMP:(2120):purging node -1198504167
*Jul 5 12:02:58.004: ISAKMP:(2120):Input = IKE_MESG_FROM_PEER, IKE_MESG_KEEP_ALIVE
*Jul 5 12:02:58.004: ISAKMP:(2120):Old State = IKE_P1_COMPLETE New State = IKE_P1_COMPLETE
CWCH#
*Jul 5 12:03:03.000: ISAKMP (2120): received packet from xxx.xxx.xxx.10 dport 4500 sport 62560 Global (R) QM_IDLE
*Jul 5 12:03:03.000: ISAKMP: set new node 599666073 to QM_IDLE
*Jul 5 12:03:03.000: ISAKMP:(2120): processing HASH payload. message ID = 599666073
*Jul 5 12:03:03.000: ISAKMP:(2120): processing NOTIFY DPD/R_U_THERE protocol 1
        spi 0, message ID = 599666073, sa = 0x854A7094
*Jul 5 12:03:03.000: ISAKMP:(2120):deleting node 599666073 error FALSE reason "Informational (in) state 1"
*Jul 5 12:03:03.000: ISAKMP:(2120):Input = IKE_MESG_FROM_PEER, IKE_INFO_NOTIFY
*Jul 5 12:03:03.000: ISAKMP:(2120):Old State = IKE_P1_COMPLETE New State = IKE_P1_COMPLETE
*Jul 5 12:03:03.000: ISAKMP:(2120):DPD/R_U_THERE received from peer xxx.xxx.xxx.10, sequence 0x63A1AE3F
*Jul 5 12:03:03.000: ISAKMP: set new node 1035716483 to QM_IDLE
*Jul 5 12:03:03.000: ISAKMP:(2120):Sending NOTIFY DPD/R_U_THERE_ACK protocol 1
        spi 2242383312, message ID = 1035716483
*Jul 5 12:03:03.000: ISAKMP:(2120): seq. no 0x63A1AE3F
*Jul 5 12:03:03.000: ISAKMP:(2120): sending packet to xxx.xxx.xxx.10 my_port 4500 peer_port 62560 (R) QM_IDLE
*Jul 5 12:03:03.000: ISAKMP:(2120):Sending an IKE IPv4 Packet.
CWCH#
*Jul 5 12:03:03.004: ISAKMP:(2120):purging node 1035716483
*Jul 5 12:03:03.004: ISAKMP:(2120):Input = IKE_MESG_FROM_PEER, IKE_MESG_KEEP_ALIVE
*Jul 5 12:03:03.004: ISAKMP:(2120):Old State = IKE_P1_COMPLETE New State = IKE_P1_COMPLETE
CWCH#
*Jul 5 12:03:08.008: ISAKMP (2120): received packet from xxx.xxx.xxx.10 dport 4500 sport 62560 Global (R) QM_IDLE
*Jul 5 12:03:08.008: ISAKMP: set new node 230166927 to QM_IDLE
*Jul 5 12:03:08.008: ISAKMP:(2120): processing HASH payload. message ID = 230166927
*Jul 5 12:03:08.008: ISAKMP:(2120): processing NOTIFY DPD/R_U_THERE protocol 1
        spi 0, message ID = 230166927, sa = 0x854A7094
*Jul 5 12:03:08.008: ISAKMP:(2120):deleting node 230166927 error FALSE reason "Informational (in) state 1"
*Jul 5 12:03:08.008: ISAKMP:(2120):Input = IKE_MESG_FROM_PEER, IKE_INFO_NOTIFY
*Jul 5 12:03:08.008: ISAKMP:(2120):Old State = IKE_P1_COMPLETE New State = IKE_P1_COMPLETE
*Jul 5 12:03:08.008: ISAKMP:(2120):DPD/R_U_THERE received from peer xxx.xxx.xxx.10, sequence 0x63A1AE40
*Jul 5 12:03:08.008: ISAKMP: set new node -1886395474 to QM_IDLE
*Jul 5 12:03:08.008: ISAKMP:(2120):Sending NOTIFY DPD/R_U_THERE_ACK protocol 1
        spi 2242383312, message ID = -1886395474
*Jul 5 12:03:08.008: ISAKMP:(2120): seq. no 0x63A1AE40
*Jul 5 12:03:08.012: ISAKMP:(2120): sending packet to xxx.xxx.xxx.10 my_port 4500 peer_port 62560 (R) QM_IDLE
*Jul 5 12:03:08.012: ISAKMP:(2120):Sending an IKE IPv4 Packet.
CWCH#no
*Jul 5 12:03:08.012: ISAKMP:(2120):purging node -1886395474
*Jul 5 12:03:08.012: ISAKMP:(2120):Input = IKE_MESG_FROM_PEER, IKE_MESG_KEEP_ALIVE
*Jul 5 12:03:08.012: ISAKMP:(2120):Old State = IKE_P1_COMPLETE New State = IKE_P1_COMPLETE
*Jul 5 12:03:13.000: ISAKMP (2120): received packet from xxx.xxx.xxx.10 dport 4500 sport 62560 Global (R) QM_IDLE
*Jul 5 12:03:13.000: ISAKMP: set new node 841395293 to QM_IDLE
*Jul 5 12:03:13.000: ISAKMP:(2120): processing HASH payload. message ID = 841395293
*Jul 5 12:03:13.000: ISAKMP:(2120): processing NOTIFY DPD/R_U_THERE protocol 1
        spi 0, message ID = 841395293, sa = 0x854A7094
*Jul 5 12:03:13.000: ISAKMP:(2120):deleting node 841395293 error FALSE reason "Informational (in) state 1"
*Jul 5 12:03:13.000: ISAKMP:(2120):Input = IKE_MESG_FROM_PEER, IKE_INFO_NOTIFY
*Jul 5 12:03:13.000: ISAKMP:(2120):Old State = IKE_P1_COMPLETE New State = IKE_P1_COMPLETE
*Jul 5 12:03:13.000: ISAKMP:(2120):DPD/R_U_THERE received from peer xxx.xxx.xxx.10, sequence 0x63A1AE41
*Jul 5 12:03:13.000: ISAKMP: set new node -820358795 to QM_IDLE
*Jul 5 12:03:13.000: ISAKMP:(2120):Sending NOTIFY DPD/R_U_THERE_ACK protocol 1
        spi 2242383312, message ID = -820358795
*Jul 5 12:03:13.000: ISAKMP:(2120): seq. no 0x63A1AE41
*Jul 5 12:03:13.000: ISAKMP:(2120): sending packet to xxx.xxx.xxx.10 my_port 4500 peer_port 62560 (R) QM_IDLE
*Jul 5 12:03:13.000: ISAKMP:(2120):Sending an IKE IPv4 Packet.
CWCH#no debug all
All possible debugging has been turned off
CWCH#
*Jul 5 12:03:13.004: ISAKMP:(2120):purging node -820358795
*Jul 5 12:03:13.004: ISAKMP:(2120):Input = IKE_MESG_FROM_PEER, IKE_MESG_KEEP_ALIVE
*Jul 5 12:03:13.004: ISAKMP:(2120):Old State = IKE_P1_COMPLETE New State = IKE_P1_COMPLETE

Jar file could not find main class.. I cant see why?

I have read loads of tutorials on this and it should be very straight forward but i STILL cant make a working jar file of my program.. please see if you can see anything wrong with what im doing..
my program is one .java file that compiles perfectly, and is runnable both through eclipse and by using the command prompt.. i made a jar file using both eclipse and the command prompt, and neither worked.. every time i run it by double clicking it i get the error "could not find main class, program will exit". here is the contents of my jar:
CorePackage\IPEmailer.class
CorePackage\IPEmailer$1.class
CorePackage\IPEmailer$SMTPAuthenticator.class
META-INF\MANIFEST.MF
the MANIFEST.MF file contains:
Manifest-Version: 1.0
Class-path: .
Created-By: 1.6.0_02 (Sun Microsystems Inc.)
Main-Class: CorePackage.IPEmailer
(yes there is a blank line at the end)
the class mentioned in 'Main-Class' has a main method that looks like this:
public static void main(String[] args) {
    // TODO Auto-generated method stub
    new IPEmailer();
}the program uses 2 external jar files:
activation.jar
mail.jar
and reads a file called:
ipemailer.ini
and writes a file called:
ip.txt
the program has no GUI and is intended to run 'silently' in the background
please help me understand what is wrong with this

package CorePackage;
import javax.mail.*;
import javax.mail.Authenticator;
import javax.mail.PasswordAuthentication;
import javax.mail.internet.*;
import java.util.*;
import java.io.*;
import java.net.*;
public class IPEmailer implements Runnable{
      * @param args
     String recipientsinput[]={""};
     String subject;
     String body;
     String server;
     String user;
     String pass;
     String from;
     String urlString = "http://www.whatismyip.org";
     String currentIP;
     String ipFromFile;
     boolean webFailed;
     long interval = 900000; //15 mins
     long oldInterval;
     Thread t = new Thread(this);
     public static void main(String[] args) {
          // TODO Auto-generated method stub
          new IPEmailer();
     public IPEmailer(){
                     ..........etccould the problem be that the class is a thread? i cant see why it would be, but ive never made a jar where the main class also 'implements runnable'

FCP HD cant see video NO WHERE!!!

Ok here it is last night I imported video in, and now today I went to start working on it and now I cant see nothing, no video at all. I reinstalled my FCP but nothing. When I put clips into my time line all I see is black, but I can hear the sound. I played it throught the camera but nothing. I opened up another project that was working that I looked at the night before to check on somthing, and today I can't see it. If I double click on the clip in the time line it comes up where I can edit it (like speed and what not) and it will play but its slow. Can anybody help me, this is a hot job that has to be done in like 2 days. HELP PLEASE!!! I NEED MY FCP ASAP!!!!!! :'(

First thing to do is select your canvas and press the w key and see if your picture pops up. Or click up the little pulldown and select Image or Image + Wireframe (not just Wireframe).
If that doesn't help, borrowing from the ever popular Shane's Stock answers:
Shane's Stock Answer #8:
If for some reason you can't view your timeline on your external monitor, there are a few things to try:
1) Make sure that the camera/deck is connected and powered on BEFORE you open FCP.
2) In the FILE menu select AUDIO/VIDEO Preferences and make sure your signal is being sent out thru Firewire DV.
3) Go to the menu and select VIEW>EXTERNAL>ALL FRAMES.
4) Go to VIEW->refresh A/V devices
5) Make sure the Log & Capture window is closed
6) Cycle power to the deck or camcorder
7) Shut down the Mac and then restart (couple this with cycling power to the deck or camcorder)
If you want it to play in both the canvas and the external monitor you need to go to the FINAL CUT PRO menu and select AUDIO/VIDIO settings and make sure MIRROR ON DESKTOP is selected under the PLAYBACK OUTPUT section
Patrick

Problem: i cant see my movies. help

I have the 30 gb ipod video and its not letting me see movies. i have purchased 3 movies from itunes and i can only see 2 of them, and ive donwloaded 2 other movies (digital copys) and i cant see them! It tells me that there "loaing" but goes back to the main menu. What is WRONG? i have enough free space....

For the iTunes purchases, the 5th gen video iPod does not work with movie rentals.
For the other movies, make sure they are supported formats. From the 5th gen iPod specs:
H.264 video, up to 1.5 Mbps, 640 by 480 pixels, 30 frames per sec., Baseline Low-Complexity Profile with AAC-LC audio up to 160 Kbps, 48 kHz, stereo audio in .m4v, .mp4, and .mov file formats; H.264 video, up to 768 Kbps, 320 by 240 pixels, 30 frames per sec., Baseline Profile up to Level 1.3 with AAC-LC audio up to 160 Kbps, 48 kHz, stereo audio in .m4v, .mp4, and .mov file formats; MPEG-4 video, up to 2.5 Mbps, 640 by 480 pixels, 30 frames per sec., Simple Profile with AAC-LC audio up to 160 Kbps, 48 kHz, stereo audio in .m4v, .mp4, and .mov file formats
(the key parts being H.264/MPEG-4 format and the resolution limit of 640x480)

How can i sync videos to my iphone 5 using Itunes 11. i also tried to convert the videos to mp4 and drag and drop the file in itunes but still i cant see videos in itunes library.

how can i sync videos to my iphone 5 using Itunes 11. i also tried to convert the videos to mp4 and drag and drop the file in itunes but still i cant see videos in itunes library.

Copied from this link.
http://www.apple.com/iphone/specs.html
Video formats supported: H.264 video up to 1080p, 30 frames per second, High Profile level 4.1 with AAC-LC audio up to 160 Kbps, 48kHz, stereo audio in .m4v, .mp4, and .mov file formats; MPEG-4 video up to 2.5 Mbps, 640 by 480 pixels, 30 frames per second, Simple Profile with AAC-LC audio up to 160 Kbps per channel, 48kHz, stereo audio in .m4v, .mp4, and .mov file formats; Motion JPEG (M-JPEG) up to 35 Mbps, 1280 by 720 pixels, 30 frames per second, audio in ulaw, PCM stereo audio in .avi file format
There are 3rd party utilities available that "rip" content into a compatible format - most include an iPod and/or iPhone format selection. If a video plays in iTunes, iTunes includes an option to convert a selection for iPod/iPhone.

HT4623 How to stop third party apps download with out you permission from ATT partners that cant see any connections on your account due to you not being the prchaser?

How to stop third party apps download with out you permission from ATT partners that cant see any connections on your account due to you not being the purchaser or on account as long as someone else is paying they can not hold legal resposible there third privacy due to legal privacy laws.

Then you should read these.
http://forums.macrumors.com/showthread.php?t=1804704&highlight=sonnet+tempo+pro
http://forums.macrumors.com/showthread.php?t=1721573&highlight=sonnet+tempo+pro
This was strange but has to do with how startup disk and nvram interact
http://forums.macrumors.com/showthread.php?t=1795765
I think your problems were solvable and not that the Sonnet card and 5,1 is not bootable, in fact the 5,1 is easier, there are more supported cards.
I have the 1,1 where the Sonnet Pro is recommended but for data only and are not bootable because of the 32-bit EFI firmware. NOT the 4,1 and 5,1. The 2008's are problem child and have a mix of PCIe 1.1 slots, first implementation of EFI64 that also has problems. Also the 4,1 has two PCIe 2.x slots 3 and 4 that share a controller but that simply limits bandwidth.
I would have left the TRIM support and NVRAM changes in Yosemite to a separate thread if you wanted to focus on the Sonnet Tempo Pro support in Mac Pro 2010-12 5,1s.
Also the make of SSD can vary and they also have their own firmware as do bootable controllers along with the EFI of the Mac, all of which have to work together. Meaning it might be that Samsung 840 va 840 EVO vs 840 Pro will all be slightly different but my experience is Samsungs work well (as do others like Crucial with the proper firmware - and there was/is an issue with the firmware of the Samsung 840 but not with booting).
The PCIe card gets seen and treated as external and therefore 'eject' but of course you can't when it is the system boot drive.
One thing I found last week and meant to mention: After installing or changing PCIe cards, RESET SMC made all the difference in the world with the long boot delay. Some PCIe cards will add a few seconds, system has to search the device tree which now shows another controller with multiple devices - and sometimes NVRAM and SMC are what I will call "dirty" and need to be rebuilt and reset.

Internal MBP HD up as external - cant see Admin user

Similar Messages

Maybe you are looking for