Internal unit HA, language EN is not maintained

HI,
I got this error message, what should i do?
Cheers,
Nies

Hi
Refer  Note 431031 - Internal unit PC, language EN is not maintained.
It can guide you a bit.
Regards

Similar Messages

  • Internal unit GAL, language EN is not maintained

    Hi All,
             i am facing problem with "Internal unit GAL, language EN is not maintained
    Message no. BM302" error while running the report...some one gave solution for this problem..still i am getting same problem ....please any one give explaination about that error why it is coming like that and also solution?
    Regards,
    surendra.

    hi..
         i  check it in that Tcode (S_BCE_68000183 or CUNI )..but it is not there..what can i do now?can any one explain about that problem? it means why it is coming like that?

  • Internal unit NO, language EN is not maintained

    Dear sir 
          When i am uploading material using  BAPI for MM01 . i am facing the following error...
    Internal unit NO, language EN is not maintained....
    So pls guide me...
    Thanks,
    Meena

    its means that the unit(base measure of unit) 'NO' not maintained in the system.
    check your BUM, it might be wrong entry or you need to maintain the BUM as 'NO' in your system.

  • Error: In language EN, the internal unit of measure DA is not maintained.

    hi
    i am doing subcontracting operation and when i try to convert the PR into p.o in co02 the system gives this error
    In language EN, the internal unit of measure DA is not maintained.
    how can i solve this error...

    Hi,
    There are couple of things..
    1. PR to PO Creation is not with T.Code: CO02.
    2. It seems you are working on Multi Global environment.
    Ask your Basis Team to do the Language imports for UOM.
    Regards,
    Siva

  • Language field is not maintained in the source system

    hi,
    I had problem with 0ehs_actn_text data source. when i'm trying to pull data to BW it's saying language field is not maintained in the source system.
    I check the datasource there is no language field in the extract structure. and No fileds are checked for slection. I found one field REFOBJ checked in the data selection tab of datasource. But the data not coming to BW side. 
    could anyone help.
    regards
    kumar

    hi kumar,
    Check in rsa6 TXTLG field should be there and it should not be checked in  HideField Tab.. then only the data will populate to BW..
    So make the things properly and once again replicate the data source in Bw side.. load the data..
    other wise if u dont wanto the language field in Bw side goto infoobject maintanance uncheck the "TExt Language dependent" option in masterdata/texts Tab.. save and activate it.. load the data..
    i hope this will help you..
    Thanks..
    ravi.p

  • BDC error BM302 : Internal unit &, language & is not maintained

    Hi Experts,
    I have Unit of measurements defined as below in T006A Tables ( Configured through CUNI tcode)
    SPRAS MSEHI MSEH3 MSEH6  MSEHT      MSEHL
    EN        UNT     UNT      UNT       UNIT         Unit
    HU        UNT     DRB      DRB      Darab      Darab
    Through BDC Prpgram  i have created an inforecord ( using ME11 transaction ), where Logon Language = HU. It is created successfully. When i try to open the created info record using ME12, the unit ( EINA-LMEIN) is displayed as '**' and it throws message "Internal unit DRB, language HU is not maintained ". When i Checked in database EINA-LMEIN is saved as '**'.
    But when i create the Info record manually in ME11,  No issues .The database EINA-LMEIN is correctly saved as 'UNT'.  
    I couldn't figure out the issue , whether problem is  in my BDC program or Language dependent configuration of the unit in CUNI. Please help in solving this issue , Am i  missing something ?
    Thanks in advance.
    Regards,
    Murali

    Hi Murali,
    You might be missing some more configuration (T table entries). To determine what that is -
    Process the info-record using ME12
    Start debugging "/h"
    Once debugging starts - place Breakpoint At MESSAGE statement
    F8
    Program control will stop at every message triggered and one of them would be you message. Check the code around the message (and call stack if required) and you might see the reason for the error
    Cheers,
    Aditya

  • Language field not maintained in the source system

    hi,
    I had problem with 0ehs_actn_text data source. when i'm trying to pull data to BW it's saying language field is not maintained in the source system.
    I check the datasource there is no language field in the extract structure. and No fileds are checked for slection. I found one field REFOBJ checked in the data selection tab of datasource. But the data not coming to BW side.
    could anyone help.
    regards
    kumar
    Message was edited by: S Kumar

    hi kumar,
    Check in rsa6 TXTLG field should be there and it should not be checked in HideField Tab.. then only the data will populate to BW..
    So make the things properly and once again replicate the data source in Bw side.. load the data..
    other wise if u dont wanto the language field in Bw side goto infoobject maintanance uncheck the "TExt Language dependent" option in masterdata/texts Tab.. save and activate it.. load the data..
    i hope this will help you..
    Thanks..
    ravi.p

  • PC UNIT NOT MAINTAINED IN LANGUAGE EN.

    Hi,
          I am doing extraction using LIS and when i do initial fill of set up tables using t code oli3 it is saying PC UNIT NOT MAINTAINED IN LANGUAGE EN.
    PLEASE TELL ME WHAT NEEDS TO BE DONE .

    Hi
    If I got your question properly, you need to run the Unit conversions for the UOM try at RSUOM or try with table
    T006 at se11.
    If you go to the domain MEINS of this data element there is conversion routine CUNIT . In this there are 2 function modules CONVERSION_EXIT_CUNIT_INPUT and CONVERSION_EXIT_CUNIT_OUTPUT . This converts PC into ST and then ST into PC . This function module you can test in SE37 .
    Hope it helps and clear

  • UOM - Not maintained in language EN

    Dear gurus,
    I have created one UOM, which is not availabel in SAP. I used the same for my MIC and did the results entry and UD.I didnot face any problem. But When iam trying to upload inspection plans thru LSMW with the same MIC, system is throwing a message UOM is not maintained in EN language. Pls guide me what  to do.
    Thanks and regards
    Venkat . V

    Venkat,
    First, you should logon in EN to the system and create the unit, otherweise you will get this error.
    Second, do settings here:
    Go to CUNI --> Go to --> translation -->unit of measurement --> Here define your langauage...
    Here select EN to EN
    Hope it solves your problem....
    Thanks!!!

  • Unit of measure is not maintained at level2 DSO

    Hi Experts,
    Unit of Measure is not maintained in level2 DSO.
    Scenario:
    We have a Product having values for different market in DSO UOM is Millions and Aggregated Value of that product is loaded in upper level DSO Unit of Measure is not maintained it shows blank.
    Solution: We have done selective deletion and uploaded again from the DSO where UOM is maintained correctly, Issue is resolved.
    We would like to know the cause of the issue.
    Please any let me know how to isolate the issue and if you have time let me call you to investigate further.
    Regards,
    Prem

    Hi Murali,
    UOM is maintained in level1 DSO correctly and for certain aggregated values it is not maintained and this very strange if we do manual upload data UOM is correct in Level2 DSO.
    I guess issue happening in regular data load or what so ever....
    We are trying to correct the data just by deleting and uploading again as this is permanent solution.
    If routines are the issue when we upload manually it shouldnt work but still working fine... this strange behaviour....
    please suggest and advise me... if required let me call you.
    Regards,
    Prem

  • IW32: Error getting message (Text for order header not maintain in lang.EN

    Hello All,
    We just starting getting this message in IW32 and IW33 stating (Text for order header not maintained in language EN) then all the pre-existing description test disappeared.
    We have not done any configuration change in this particular system.
    Can anyone help to resolve this.
    Thanks

    Hi,
    As with most SAP messages it is always a good idea to trust what it is saying.
    The system is telling you that KG has not been created in the English language.
    Go to transaction CUNI to check the settings.
    Select the Unit of measure for "MASS" (from the drop down list) and check the entries for UOMs.
    KG should be there and should have an English description (the message said it was not there for EN)
    If it is there and set up correctly then there might have been something else in the UOM field? You didn't enter " KG" did you (a blank character then  KG?)
    Steve B

  • Have 2 airport extreme base stations connected in chain.  Airport utility shows slave unit without power. However, power is on slave unit, but status lights do not show up at all. Small green lights at each back port blink.  Anyone have any ideas?

    Have 2 airport extreme base stations connected in chain.  Airport utility shows slave unit without power. However, power is on slave unit, but status lights do not show up at all. Small green lights at each back port blink.  Anyone have any ideas?

    Unfortunately, you are describing the symptoms of an AirPort Extreme with a failing (or failed) internal power supply.
    As a last resort, try a Factory Default Reset on the AirPort Extreme as follows:
    Power off the AirPort by pulling the power cord
    Wait a minute or two
    Hold in the reset button first, and keep holding it in for an additional 8-10 seconds while you simultaneously plug the power back into the AirPort
    Release the reset button and allow a full minute for the AirPort to restart
    Now try to configure the AirPort again.  If you continue to see the same symptoms as before, the AirPort will need to be replaced.

  • HP Officejet 6500A Plus will not maintain wireless connection reliably

    For the HP EXPERTS on Expert Day, April 18, 2012:
    B.L.A.T. (Bottom Line At Top):  We have an HP Officejet 6500A Plus purchased about 5 months ago.  We wanted to use it as a wireless-connected printer in another room besides our home office.  It is useless to us because it will not maintain its wireless connection, even sitting just a few feet from the router in the same room.  Except for numerous hours of troubleshooting, we have left it sitting powered up, but unused and idle, for almost the entire 5 months in our home office.  DURING ALL THAT IDLE TIME, IT HAS LOGGED OVER 3,200 DISCONNECTS, at a consistent rate of 24 disconnects every 24 hours, even though it ALWAYS reports that the wireless signal quality is “EXCELLENT” (all this is according to the Wireless Network Test Reports we’ve printed throughout the last 5 months).  So our question is, what is it that this printer is trying to do once an hour over a wireless connection that is causing these thousands of disconnects?  And how can we stop it?
    NOTE!  Before you round up the usual suspects (namely our router and our PC firewalls) please note that we also bought an HP Officejet Pro 8600 Plus ON THE SAME DAY as the Officejet 6500A Plus.  The 8600 was also installed with a wireless connection, and has worked without a single network issue for the entire 5 months.
    NOW, FOR THE REST OF THE STORY…
    WHO WE ARE:  My wife and I have worked on HP equipment for 33 years, starting in 1979 as corporate customers of HP when we worked for Exxon; then we both worked for HP directly for 17 years; and we’ve now used dozens of pieces of HP equipment in our home during the last 12 years in retirement.  We’re primarily software folks, so we’re not exactly experts in hardware and networking, but on the other hand, this ain’t our first rodeo either.
    OUR CONFIGURATION: 
    PC’s – All running Windows 7 x64 with all important patches applied and Norton Internet Security 2012:  HPE-270f and HP AIO 200-Quad, each with full 6500A and 8600A drivers installed on wireless connection.  These 2 PC’s themselves can connect either wirelessly or via Ethernet to our home network.  The 270f has a dual-band wireless board.  Both bands work.  We also have a new dv7t laptop with only the full 6500A driver installed via wireless connection.  The laptop is now upstairs and it’s connected to our home network wirelessly without any issues.  (This is where we had hoped to also put the 6500A, but it needs to work reliably via wireless connection.)
    ROUTER:  Netgear N600 WNDR3700 providing Ethernet and wireless networking.  Router provides a very strong wireless signal throughout the house.  No wireless problems with any other equipment including an iPod, two Kindle Fires besides all the HP equipment.
    PRINTERS:  Besides the two HP printers, the HPE-270f PC has a Canon MP960 installed on it.  And if we can’t get the 6500A working right or replaced with something that does work right, we may be buying our second Canon printer.  By the way, on the 6500A, ePrint and App’s are set to ON, but of course they’re not being used, just like everything else on this AIO.
    OTHER:  We also have a Sonos music system that connects to our network via Ethernet and has its own proprietary mesh network (on another frequency) for transmitting ripped music wirelessly to speaker units throughout our house.  (If you aren’t familiar with this totally cool system, check out sonos.com).  We’ve never seen any evidence of interference between these two wireless networks, or our wireless phone sets either.
    HP TOOLS AVAILABLE ON ALL 3 PC’s:  HPU
    UPDATE 5.003.001.001 (reporting everything up-to-date); HPHDU 3.1.0.17; HPPDU 5.0.0.015 and HPNDU 4.3.0.002. 
    SYMPTOMS:  The 6500A Plus installs quickly and easliy, and connects wirelessly just fine during installation.  But sometime over the next hour (usually less), it disconnects and won’t print from PC applications.  Sometimes the application puts up an “Unable to communicate with printer” screen, even though the PC usually thinks the printer is “ready”.  Other times, the PC thinks the printer is offline (but printers don’t have “offline” buttons anymore!).  Often, if you just leave everything alone, the 6500A will somehow reconnect and print out the spooled file 5-30 MINUTES later.  So it does usually seem to be able to recover given some time, but that doesn’t always fit our schedule!   Occasionally, turning the wireless radio on the printer off and back on will fix it right away.  But usually, you have to power the printer completely off, and then back on.  As far as we know, that always fixes it…..until the next disconnect a few minutes later!
    PREVIOUSLY TRIED:  After reading some of HP’s wireless network support websites, I manually assigned a fixed IP address to this printer.  It didn’t seem to matter; according to the wireless network test report, it still logs disconnects at the rate of one per hour, and all the failure symptoms were the same.
    We also dabbled a bit with setting this printer as “trusted” to the Firewall, but that didn’t seem to matter either.
    Next, we connected the printer via Ethernet.  The printer immediately started to work, even though it had just been in its “failed” state over the wireless connection.  As far as we know, it never failed while connected via Ethernet.  This seems to point to a purely wireless hardware/firmware problem on the printer itself.
    Late last year, I tried two different chat sessions about this with the inter-continental AIO support teams, each one lasting several hours.  Unfortunately, none of their optimistic solution scripts seemed to fit our problem.  They both seemed determined to reconfigure the 6500A as a TCP/IP printer, which of course worked fine initially, just like everything else.  At this point, they would understandably want to close the chat.  But 20-30 minutes later, we could no longer print to it.  During the second chat, they got into one of our PC’s remotely and effectively turned off the spooler (by selecting “Print Directly” or something like that).  After that, all was well again (as usual) UNTIL the printer disconnected, at which time attempting to print from that PC would HANG the application (since the spooler was no longer buffering) and eventually hang the whole PC.  One giant leap backwards.  That’s when I gave up on the multi-hour chat sessions.
    The three diagnostic utilities (HDU, PDU, NDU) have been tried over and over.  When the printer is in its disconnected state, the DU’s usually don’t detect the 6500A at all, or if they do detect it, they are unable to fix anything.  Frankly, it’s easier to just power the printer off (which takes about a minute) and power the printer back on (which takes more than a minute) and then wait for the spooler to kick in (usually about 30 seconds).  BUT WE DON’T CONSIDER THAT A SOLUTION!!
    B.L.A.B.  (Bottom Line At Bottom):  We have used up nearly the entire black ink cartridge and at least a ream of paper troubleshooting this brand new printer, to no avail.  This printer is useless to us unless it can maintain a wireless connection reliably.  Please help!
    Thanks –
    Bob and Jane
    (Note: we have an appointment from about 11:20 am EDT – 1 pm EDT, 8:20 am PDT till about 10 am PDT)

    I bought the Officejet 6500A Plus about one month and have experienced the very same problem. I tried to remedy this problem following suggestions in a number of different posts (static IP, router, firewalls etc), all to no avail. Last week I called support. The support I received by the tech over several hours and different days for a week was very good. However none of his suggestions corrected the connection issue. After today's recommended fix failed, he advised HP is aware of this issue with the 6500 and other affected printers. He claimed HP was working on a firmware upgrade. He did not know when the update would be provided. The tech also claimed HP acknowledged this problem in a written announcement. He agreed to email the announcement to me. I haven't received it. This has been the only problem I've had with the 6500

  • Internal Unit of measurement in J1ILIC01

    Hi,
    While creating Deemed Export Licence thru T.Code J1ILIC01, I came across one issue that when I enter the Material Number it only pics the description of material. However, the UoM is not picked automatically.
    When I tried to put it manually, it will not accept.
    It only accept the Internal Unit of measurement instead of Commercial Unit of measurement.
    Thanks.

    Thanks Marcin,
    Just to clarify from my side,even though the error occured only for one UOM,no unit of measurement are available.
    Does your solution still apply?
    Thanks for your help.
    Best Regards.
    jayawant

  • Unit of measure ST is not defined as a commercial unit

    Hi Experts,
    While doing Punch Out catalogue in the Maintenance Order, i have received the following error "Unit of measure ST is not defined as a commercial unit".
    I have checked in the transaction CUNI, and ensure that the above UoM is maintained.
    This is a standard error message M3 491.
    Any pointers will be appreciated....
    by
    Prabhu

    Hi Prabhu,
    GOTO CUNI
    Check whether Commercial meas.unit field is ticked or not in application Parameters tab.
    If not maintained, maintain here the tick
    Regards,
    Amol

Maybe you are looking for