Internal warning 0xAFBF5C57 on startup with LabVIEW 2011 Student edition

Upon opening LabVIEW 2011 student edition, I get the following error everytime I open it.
I am using the it on a Mac computer, with Mac OSX 10.7.1, the Lion edition operating system.
Attachments:
StartUpError.jpg ‏52 KB

Hi Joe,
Have you ever successfully opened LabVIEW 2011 on your Mac?
Also, can you tell me what processor does your Mac has? I want to make sure that there is not a compatibility issue here. Please reference to LabVIEW Version Compatibility with Mac OS PPC and x86 Processors for the compatibility list between LabVIEW and Mac.
Regards,
Daniel
Regards,
Daniel REDS
RF Systems Engineer
Help us grow.
If a post solves your question, mark it as The Solution.
If a post helps, give Kudos to it.

Similar Messages

LabVIEW 2011 Student Edition on Mac Installation

Hi
I installed LabVIEW 2011 Student edition on my Mac with the OS Mac OSX Version 10.7.1 Lion edition.
At first it wouldn't install (I had installation failure because Lion OSX is 64 bit and not 32)
I used the intructions as demonstrated in the link http://support.apple.com/kb/HT3773
as I found in the forum thread of:
http://forums.ni.com/t5/LabVIEW/Installing-LabVIEW-2011-for-Mac-OS-X-10-7-Lion-fails/m-p/1653742?req...
After I changed to 32 bit, the apple terminal warned me by doing so I wouldn't be able to save stuff correctly.
The software installed after I used the directions for 32 bit mode, but for some reason it did not say I was in 32 bit mode on the Apple activity monitor, it said 64 bit.
I went to the terminal and used the instructions to turn the operating system into 64 bit (even though it already say it was in 64 bit, despite LabVIEW installing, which requires 32 bit). I rebooted the computer, and I was able to use LabVIEW 2011.
My question:
Once LabVIEW 2011 Mac student edition is installed in 32 bit mode, can it be operated when the computer is in 64 bit mode?
thanks
Solved!
Go to Solution.

Hi JoeGanser,
Booting your Mac into OSX 64 bit should still enable LabVIEW to run, even though it is a 32 bit program. You will encounter problems however when using NI-DAQmx Base, NI-VISA or NI-488.2 drivers while running in 64 bit mode.
I have found a KnowledgeBase Article, which explains why this is the case.
Please let me know if that answers your question, please post back if you have further questions.
Regards,
Ben B.
Applications Engineer
National Instruments UK & Ireland
"I've looked into the reset button, the science is impossible!"

Will the ELVIS board work with LabVIEW 2010 Student Edition?

I recently acquired a traditional ELVIS board (with the PCI DAQ board). So far I've only installed the evaluation for LabVIEW 2010 (x64), and when I attempt to install the ELVIS Traditional 3.0.5 software I get the following message: "This installer requires LabVIEW 8.5 Full Development system or later to be present on this computer. LabVIEW Base Development System in any version of LabVIEW is not supported. Please install LabVIEW and then run the NI ELVIS installer again."
I am eligible to purchase a student license for LabVIEW 2010 and would like to know if the ELVIS Traditional 3.0.5 software will install after I've acquired a student license.
I am running windows 7 (x64) with an evaluation version of LabVIEW 2010 (x64).
Solved!
Go to Solution.

Perhaps I spoke too soon. I purchased a student license for LabVIEW 2010 and am still receiving the same error. I've provided screenshots of my license and the message from the ELVIS Traditional 3.0.5 installer.

Labview 2010 Student Edition, will it work with the Labview FPGA module and Xilinx Spartan 3E??

Just as the title states.
I did a search here on compatibility, but I am coming up short with not much to show for it.
I have Labview 2010 student edition, 32bit and 64 bit. I am trying to do a Senior Design project for my undergrad, and I am having some issues.
I was able to download the Support for the Xilinx Spartan 3E and Labview FPGA.
I install it, it runs through the unzipping process, installs, and then mysteriously I cannot find it. I have looked through my programs list and it is not listed. I open both editions of LabView and I find ABSOLUTELY NOTHING indicating that either one has ANYTHING to do with FPGA.
Did I install it wrong? Or is it just not supported in the studend version of Labview???
Can someone help me, please?

M Boat wrote:
What about the trial version? Any chance of it being on there?
I think everything is available for download, and without activation it will be in trial mode and you have about a month (?) before the trial expires.
A trial version of the FPGA module is available for download here. I have no idea if it would work with the student version.
I would recommend to talk to your local NI sales representative for advice. Good luck.
LabVIEW Champion . Do more with less code and in less time .

How to download LabVIEW 11 Student Edition for OS X

I received my activation number for LabVIEW 11 Student Edition by email for participating in an online lecture and solving a problem.
In the email there was no link to download the software.
Where can I find a download link for LabVIEW 11 Student Edition for OS X?

Hi,
I will try to go through it with you and I believe we will find a solution.
The 2011 version of LabVIEW for OS X is no longer available from this link, a new version was released in the meantime. First I'd like to try to get a new version to you. Can you please check whether you can't get the serial number for the new version as well? Usually these student versions are available for free.
In the worst case I will upload you the old installer on the FTP.
Jakub Prokeš
NIEE Aplications Engineer

Labview 2009 Student Edition Vista x64 installation fail, no error messages though

I am trying to install a copy of the LabView 2009 student edition and everytime the installation initializes, the modules fail to install for every single module. There is also no error message.
I got a message that LabView may not be working correctly due to Windows Firewall, which I have disabled. That message referred me to ni.com/info, code expm69.
Let me know, I'm a little confused as to what's going on. Would it be due to a patch or what not?
Thanks!
Solved!
Go to Solution.

Hi imagineerme,
Regarding your installation issues, a possible cause may be that you don't have permissions on the computer that you are installing. Are you set as the administrator on this computer? Is this a school computer or your own?
It's also possible that LabVIEW may be installed on your computer already. To check this, go to Program Files/National Instruments to see what you already have installed.
If neither of these are the cause, can you please provide me with more information about your installation? Does the installer crash or just go straight to the finish screen? Does anything install at all? Thanks and best of luck,
Julianne K
Julianne K
Systems Engineer, Embedded Systems
Certified LabVIEW Architect, Certified LabVIEW Embedded Systems Developer
National Instruments

Who is eligible to use the Labview 8 student edition?

Who is eligible to use the Labview 8 student edition? Can an individual who is not in school or affiliated with a learning institution purchase and register it for the purpose of learning at home?

LabTech wrote:
Maybe I'm missing something, but I still am not sure of the answer to my question about the Student Edition . Maybe it hinges on what the word staff means in this case?
I would interpret "staff" in the most general case. If you are employed by an educational institution, and not student or faculty, your'e probably "staff".
The main restriction on the student edition is in its use. You can only use it for personal educational use and not for research. For research in a lab, you need to get the real LabVIEW. See e.g. point #4 in the FAQ: http://www.ni.com/labviewse/labviewse_faq.htm ).
Still, the educational discounts are great (75% on single copy software: http://www.ni.com/academic/edu_dsct.htm ).
Message Edited by altenbach on 09-13-2006 10:02 AM
LabVIEW Champion . Do more with less code and in less time .

Running LabVIEW Express Student Edition.

Purchased LabVIEW Express Student Edition, installed the software that
comes with the book. Application does not run, error message is
"attribute on localhost have been configured improperly". How do I
resolve this problem, any solutions

Hello,
I have not seen this error before, can you attach a screenshot and/or perhaps an error number that accompanied the problem? In the mean time, here are a couple documents providing solutions to problems others have had with the student edition:
http://digital.ni.com/public.nsf/websearch/3AC8A893446873E686256B22006C2DEF?OpenDocument
http://digital.ni.com/public.nsf/websearch/98DFF2B564902B9886256FB1004E448F?OpenDocument
Also see the related links in the pages linked above.
Best Regards, and I look forward to hearing back from you!
JLS
Best,
JLS
Sixclear

I cannot see the NI-DAQmx icon in measurement window in Labview 2013 (student Edition)

Hi All:
I have installed NI-DAQmx and Labview 2013 (Student Edition). I have connected an NI USB-6008 DAQ and tested it using NI-DAQmx and it is working properly.
Now I tried to do logging of data from this device using the installed Labview software but as I open a new project and go to Block Diagram screen and display the measurement menu I cannot see the NI-DAQmx icon in the measurement window (Menu) within Labview 2013 (student Edition).
Any suggestion?
I am attaching two screen shots.
Please help.
Thanks
Solved!
Go to Solution.
Attachments:
1.png ‏77 KB
2.png ‏88 KB

In which order did you install the software packages?
You should install LabVIEW first, followed by DeviceDrivers!
Best regards,
GerdW
CLAD, using 2009SP1 + LV2011SP1 + LV2014SP1 on WinXP+Win7+cRIO
Kudos are welcome

Labview 8 Student Edition?

In an Academic Update email from NI today, it mentioned Labview 8 Student Edition. Is this available now?
Jeff

I heard something like that just yesterday at a local NI activity. You may need to contact NI directly and/or keep an eye on this page.
www.vartortech.com

Install labview 6.1 (or compatible) run-time engine with labview 2011

I have installed a trial period version of Labveiw 2011 in order to check for possible upgrade issues I may have if I decide to upgrade from labveiw 6.1. Well, needless to say there have been alot. That is as expected since I have not updated labview in many years. I am still not under any pressure to update; however, I would like to in order to get support and make sure I do not have any compatibility issues with new equipment purchases. I have been able to resolve most of my compatibility issues with simple code fixes and such. However, twice now I have run into an error when launching labview executeables compiled by two different equipment manufacturers. The equipment I am using is not even old...maybe a year or so. When I launch the labview executables to control this equipment on a PC that has the trial period labview 2011 installed, I get an error message stating something like " This requires a Labview 6.1 (or compatible) run time engine." I have tried to download and install the 6.1 labivew engine but I can't install this engine on a PC which has labview 2011 installed. Can someone explain how I am to run these executables under labview 2011. I can't imagine these executables were developed using 6.1 since this equipment is not even a year old now.
Solved!
Go to Solution.

Im not for sure I am on the same page with you here. Im not trying to develop any code myself. I have some labview executables that came with hardware we purchased in order to control it. We used to have labview 6.1 installed; so everything was working ok. But now that I have installed 2011, I get an error message when trying to run these executables. The error message states that this executable requires a labview 6.1 or compatible run-time engine. I have seen this error on both XP and Windows 7 machines. I did not develop the executable, it was developed by the hardware manufacturer. But since this hardware is only about 1 year old, I an assuming they used a newer version of Labview to develop this code. Certianly newer than 6.1.
So I guess my question is..is there a way for me to get this executable to work on a PC that has labview 2011 installed. I have tried to install a labview 6.1 run time engine but it will not install. Any other options?

Application crashes when calling DLL built with LabVIEW 2011

Hello everybody,
Our application calls DLLs built with LabVIEW 2010 SP1. We installed LabVIEW 2011 and built some DLLs. So far so good. If we start our application and run 2010 DLLs it still works fine. If we run a 2011 DLL just once no error happens, but if we try to run the same 2011 DLL our application crashes reporting the error below. I saved the code for 2010 version and built a DLL and it works fine. Does anyone know why?
Thank you in advance.
#Date: Fr, 16. Sep 2011 16:25:25
#OSName: Microsoft Windows XP Service Pack 3
#OSVers: 5.1
#OSBuild: 2600
#AppName: PasTA
#Version: 11.0f2 32-bit
#AppKind: AppLib
#LabVIEW Base Address: 0x30000000
16.09.2011 16:25:26.181
Crash 0x0: Crash caught by NIER
File Unknown(0) : Crash: Crash caught by NIER
minidump id: 8a779b3f-51d7-4864-8e4d-6ab0195cd158
ExceptionCode: 0xC0000005
N
0x3072C804 - lvrt <unknown> + 0
0x3072CBB8 - lvrt <unknown> + 0
0x7C864191 - KERNEL32 <unknown> + 0
0x7C83AB50 - KERNEL32 <unknown> + 0
0x00000000 - PasTA <unknown> + 0
Attachments:
error.PNG ‏11 KB

On that note, you should be able to create DLLs in 2010 and run them with 2011, correct?? In my case, I have a 2010 built DLL (talking to sbRIO), most of the functions work when run in 2011, but a couple of them lock up LabVIEW on the desktop (but not the sbRIO), no lock ups happen with 2010 on the desktop.

Cannot execute a library created with Labview 2011 in visual C++

I created a very simple DLL in Labview 2011, then, I try to call this DLL from a Visual C++ 2005 application.
I have tried to load the DLL at compilation time with the .LIB and .H files, and also dynamically with AfxLoadLibrary.
When I try to call the library function, it works fine, but the second time i call the library freezes the app.
all the library does is to show a simple dialog box and that's it, no params, no returns, no nothing,
but it freezes the app, why the VI works in Labview, but in DLL doesn't?

Hi Alveru,
What might be happening is that the process never ends and when you try to re call it, it fails and that it is why your app freezes, what you can do to probe is that is what is happening is to test your DLL directlly in LabVIEW with the Call Library Function Node so you can import the DLL and test it. If it also freezes or not work as expected the problem is with the DLL.
The proceses are automatically closed by LabVIEW at the moment the VI stops running; however, when you deploy the vi, you need to close them manually.
Try this out!!
Regards,
Luis Fernando
National Instruments Cono Sur
Ingeniería de Campo y Consultoría
http://chile.ni.com/

I have Microsoft Office 2011 Student Edition installed on MacBook Pro; Can I install Microsoft Office Windows 2008 onto Mac without deleting Microsoft Office 2011?

I have previously installed Microsoft Office Student Edition 2011 on my MacBook Pro. While installing Microsoft Office 2008 Windows; message prompts to delete Microsoft Office 2011. Is there a way around this issue?

Office 2008 was a Mac version. The equvalent Win version is 2007. So there is no "Office 2008 Windows." Which version are your trying to install?
Are you using Boot Camp to run Win on your MBP and want to install Office for Win there? I can't see that being a problem..
I do know that the regular version of Office Mac won't run properly if the trial version is present. The installer is set up to look for other versions, resumably to keep the trial version and the regualr from clashing.
Office Mac 2011 is equiv to Office for Win 2010
Office Mac 2008 " " " Office for Win 2007
Office Mac 2004 " " " Office for Win 2003

Labview linux student edition?

Hi,
Is there a Labview DEMO version for linux? Or maybe a student edition.
I need it for school and have to make a presentation about it and thats all.
I hope there is a trail version for linux.
Greets Jellee.

Hi Jellee,
No there is no evaluation or student edition for LabVIEW for Linux, please contact you local NI Office and inquire for the possibilities.
Thanks
Karsten

Internal warning 0xAFBF5C57 on startup with LabVIEW 2011 Student edition

Similar Messages

Maybe you are looking for