Internet access problem

I am having a problem with my WRT54GS router not being able to access the internet. I can see it and administer it via wired or wireless connection. I have tried the below steps in effort to trouble shoot with no success:
1. verified that I am using a cable that works to go from my cable modem to the router
2. reset the settings to default
3. verified that it will not ping any web sites
4. verified that it is picking up an ip address from the DHCP server *scratches head*

As you are using Cable connection follow this steps .........
1) Connect the computer to the router & router to the cable modem
2) Check the Ip address on Local area connection .... if getting any valid Ip like 192.168.1.X with gateway 192.168.1.1 ....... ping the gateway address .....if getting reply open the set up page using http://192.168.1.1 ....
3) You will see username & password screen...... leave username blank & in password use admin........
4) Look for mac address clone sub tab ..... under set up tab.....
5) Enable the service & click clone my pcs mac ........ click save settings ............
6) Click status tab.....check the Internet Ip address ........
7) Do power cycle & try going online ...........

Similar Messages

Internet access problems and viewing video on internet

I have very limited interet access most of the time. I get a message: "You are not currently in an area that can handle data communication. ..." I have no problem with email and other features of the phone during this time. The signal at the top of my phone says "GSM". When I am able access the internet, it give me a different signal (can't remember what that is, however). Even then, I cannot view most video clips, such as YouTube clips. They will not load all the way. It states, "Error has occurred in attempting to play media." Help!

I have unlimited internet access, so that's not the problem. Right when I got the phone, I replaced the original data card with a 4G card and enabled mass storage. I have (since my first post) had more access capability by enabling the WiFi (da) which finds my wireless connection at home. I've also been able to view a video clip, not successfully all the way through, however. During viewing, the phone appears to crash, i.e. the screen goes white and then it takes 3-5 minutes for it to reboot. This has also happened when the phone has not even been being used. Also, as I was surfing the net, the phone asked if I wanted to enable Javascript which I did. Is there anything else that I need to enable or do to the phone in order to have a more pleasant experience using the internet and viewing video clips?

Z60t wireless/Internet access problem

I purchased in 2006 at office depot, after a year and a half of using it just stop accessing the internet, I am so desperate since I am not a computer junkie, my needs are simple just to be able to receive and send emails and easy net surfing. I called Lenovo but they are not willing to help since my machine is out of warranty. Please help me, I lost my jo, my home cannot afford to take it to a service location IBM recommends. Thank you.
Moderator edit: Added description of problem to subject.
Message Edited by bananaman on 07-12-2009 10:58 PM

Hi there Bananaman, you are one of those wonderful volunteers out there, anyway, as I have said purchased machine on 06 worked for at least year and a half then quit on me. I cannot access the internet, took it to office depot since I purchsed it from them, they're offering FREE tune up had me purchase a Linksys LAN card telling me the built in wireless netcard had given up on me. Did not help, they sent me home w/ the LAN card assuring me it will work since in my house I have a wide range of wireless internet connection whatever. Did not work either. Called IBM Lenovo only to be declined of tech support because machine not warranty covered. Yesterday, I tried to fix it(LOL) for a miracle to struck me but to my despair. I don't know what to do, I want to take it to service center recommended by IBM but got no green. I am hopeful that, being a member of the Lenovo community, I could find some real help from real people like you. These are the characters I see at the back of my machine I think as the product number, (TYPE 2511 - FEU S/N ******* 0510) Thank you.
Moderator edit: Masked serial number to prevent mis-use.
Message Edited by bananaman on 07-12-2009 10:54 PM

Internet access problem via wlan on Orange Nokia N...

I have had a nokia N80 for a few days, and can I get the wireless access working to access the internet, can I hell!
I can get the phone to connect to my router via dhcp or static ip address. I can enable security, have an open network and can even ping my phones ip address so I know the link is working via wireless.
It's just when I attempt to connect to wlan on the internet is says the usual 'web no gateway reply'. Has anyone got this working with a linksys wag54gx2 wireless router?
Stan..

Hi,
Don't know if this might help?
Menu > Tools > Settings > Connection > Access Points. Open the connection in question and press Options > Advanced Settings > IPV4 Settings > DNS Address. Enter the IP address of your router here, then reboot the phone and try to connect again.
BR
SR

E71 PC Internet Access DNS Problem

Hi all,
Got a bit of a problem which I hope someone knows the answer to.
I'm currently triailing tethering on an E71 for our corporate network. I've got the phone connected up and installed Nokia PC Internet Access on my machine; all good.
The problem I'm having is that we use a private APN at the mobile carrier to connect back to our network, and this does not advertise automatic DNS settings to clients. I can get connected to the APN no problem at all but without DNS servers on the connection, it's fairly useless.
Now, I can see that the PCIA application uses Dial-Up Networking behind the scenes to actually connect up, and I have tried to specify manual DNS servers on that connection, but every time I reconnect using PCIA, it resets everything back to automatic, which doesn't work.
Anyone got any ideas on forcing manual DNS servers on a connection when using PC Internet Access?
Thanks all!

Nobody? This is the way how Nokia does NOT care us. Nokia is now dead

I'm connected to the wifi at home but no internet access. i was surfing on the same wifi without any problems. and also this issue is for other wifi network.

hello everyone.
i was surfing browsing and downloading on my iphone 4 on my home wifi and other places without any problem but today i found out that even though i'm connected to my wifi i got no internet access. i also got this new problem, my led flash is on. if i tilt the device the flas dims a bit. i tried switching off the device but still the flash is on. i tried using at other wifi network same problem. i tried forget this network, switching off and turning on the device i also tried reseting the network and also hard reseting the device. but still same problem. what can i do about this? and if i send it to apple what are my options? i got warrant coverage so will they be able to repair it ? if they are not able to repair then will they give me new iphone 4 or refurbished iphone 4 for replacement?

Apple does not repair devices. If they are covered under warranty, the device is replaced. You will not get a new phone, you will get a service unit which is as good as if not better than new.
If all the basic troubleshooting from the User's Guide has been done and the device does not get Internet access via Wi-Fi from multiple locations, the only thing left is to take it to Apple.

HT201320 I cannot send email. I have internet access. What could be the problem?

I cannot send email. I have internet access. What could be the problem?

Hello, ootytooty.
Thank you for visiting Apple Support Communities.
Here is an article I would recommend going through when experiencing issues with mail.
iOS: Troubleshooting Mail
http://support.apple.com/kb/ts3899
Cheers,
Jason H.

Lumia 920 service problems/ no internet access. Also problem with receiving calls?

As of yesterday I have been having a wierd problem with my Windows phone, and exploring through the web, I've seen a couple of other people with this problem as well, with no one really coming up with any other solution but to do a hard reset, which I abosuletly want to avoid. So my problem is that I don't seem to have any internet access, regardless if I am connected to 4G or through wifi. This is real wierd because it just started happening all of a sudden. I didn't do any update, didn't download anything new, nothing like that.I know for a fact that I'm simpily not just mistyping addresses or have airplane mode on, I'm stumpted as to why this is happening. To add another layer of confusion, I don't seem to receive all calls I get. For instace: yesterday, one of my friends called me, I received his call right? Well later that day, my Father apparently called me, but I never received any nottification or even a voicemail that he ever did. What the heck is going on here and what can I do to resolve this??

Hello @ThomasWolf
I’m sorry to hear you’ve been experiencing issues with your phone.
When you say you’re unable to access the internet, is it just via your Web browser? Or is it apps that require data such as Facebook, YouTube, etc.?
Have you tried via more than one Wi-Fi network as well?
Try to open up att.com/ttr via your mobile web browser; do you see a confirmation page?
If you’re continuing to have issues, then please contact us.
Thank you,
Charise

Networking problem (internet access)

My host has no internet access, but the VMware guests do. Because the host has no access, the NAT over host doesn't work when I want to access the internet.
Therefore I added a third bridged network card. With this card internet works fine, but the Oracle Cluster doesn't work any more. It seems to get confused by the added card.
What must I do to make Oracle work again? - Or is there another way to access the internet from the guest if I don't want to let the host access it?

My host has no internet access, but the VMware guests do. Because the host has no access, the NAT over host doesn't work when I want to access the internet.
Therefore I added a third bridged network card. With this card internet works fine, but the Oracle Cluster doesn't work any more. It seems to get confused by the added card.
What must I do to make Oracle work again? - Or is there another way to access the internet from the guest if I don't want to let the host access it?

WRT 120 Internet Access Control Problem for itouch

I've just set up my router. Cannot seem to control access to the internet for my son's itouch. The router recognizes it on the map as a wireless device part of the network, but it will not show up in the menu that allows for internet access control. My lap top shows up, but no itouch. I'm running Windows XP home premium edition - not sure if this makes a difference.

Open the linksys setup page...Under the Wireless tab,Change the Channel Width to 20MHz only,Channel to 11 and click on save settings...Under the Advanced Wireless Settings,Change the Beacon Interval to 75,Change the Fragmentation Threshold to 2304,Change the RTS Threshold to 2304 and Click on Save Settings...
On the I-Touch..Go to Settings>>>General>>>Reset>>>Now select Reset Network Settings.This will now reboot and restore you network connections.

JetPack 4G LTE connects but "no internet access" message

Would appreciate any help.
My JetPack 4G LTE mi-fi connects to the internet (3G or 4G) and shows that my devices are connected to it. However, I cannot get on the internet.
1) I have three different devices - two laptops and a smartphone. All three have the same problem.
2) I have a Sprint Mi-Fi that I use for a different business. All three devices can and do connect to that device and work properly on the internet during the same sessions in which they cannot connect on the Verizon JetPack. So it is not the devices I am trying to connect with.
3) The exact same thing has happened several times over the course of about 4 days and in two cities and two states - all three devices unable to connect via JetPack but connect fine through Sprint Mi-Fi. So it is not location or local network issue.
4) LED display on JetPack, in all instances, show a strong 3G or 4G (depending on where I am) signal and also that all three devices are connected.
5) Message on laptop wireless area shows connection but says "no internet access".
6) Under the wireless status or details, it says (on the list of info): "IPv4 no internet access" and "IPv6 no internet access".
7) I have done a battery pull with no effect.
8) I have done a factory reset (power up, remove cover, press reset button until long green light and short green light) with no effect.
9) After both battery pull and factory reset, I still show connected to 3G, all three devices connected, no internet access, and all three devices then work on the Sprint mi-fi.
10) Symptoms started about 4 days ago and have not changed since - it is not a come-and-go problem. It is not working at any time.
I am hoping to gosh to avoid a long ordeal with tech-support at Verizon. This is a company-issued device, so I could ask my company to take it up with Verizon, but I work remotely and access to the IT department is not that simple either. thought I would see if I am missing something simple. I hope I've given enough info for someone brighter than myself here can spot something I could do.
Thanks in advance for any help.

Thank you for your response. I am having trouble logging back into this site to respond (I never created a User ID and don't know my cell phone number as it is a mi-fi and not a cell). I reregisterd for the forums only under a slight ID variation and will continue to do so for this dialog. Thanks very much.
The back of the Jetpack says SSID: "MiFI4620L Jetpack 89B4". I am currently using the device (since the problems began last week) in zip codes 49504 and 49503 - same symptom both places.
Thanks again.

Is it possible to be connected with a 3G modem for internet access and a WiFi router for printer sharing at the same time?

For our only internet access we have a 3G wireless modem. I have since purchased a WiFi printer and router to connect all the comptuters to in the house. The PCs have no problem with using both the 3G connection and the WiFi signal at the same time to print, however, the MacBook Pro will not connect to the 3G network and the router, it will drop the internet access from the modem and attempt to connect via WiFi (which has no internet access). Is there a solution that is available to remedy this? I attempted to create an adhoc printer network, however, the macbooks again will not print off of this, only the PCs. And I'm getting a bit frustrated overall with this.

The 3G wireless modem is on one of the PC's correct?
Why don't you pass the Internet through the Ethernet port to the router via Cat5 cable, then have that transmit a Wifi signal that everything else can use, then connect the printer to the router for print sharing?
You would have to turn off the wifi on the comptuer with the 3G modem as it's physically connected to the router and can't connect to the other machines as they are all connected to the router for sharing.
The Mac has the ability to pass, Internet Sharing in the System Preferences.
Do you have software for the Mac to run the 3G modem?

Safari and firefox stop working after a few minutes of browsing, regardless of what site I'm on. I have to restart my computer to get internet access again but it only works for a few more minutes, then I have to restart again. Please help!

Safari and firefox stop working after a few minutes of browsing, regardless of what site I'm on. I have to restart my computer to get internet access again but it only works for a few more minutes, then I have to restart again. I don't get a spinning ball, it just stops working at whatever page it's on. I can close the program just fine but when I re-open it, either safari or firefox, it freezes trying to load the hompage. This started a few days ago after trying to stream a movie on my computer. I'm on a Mac Air OS X Version 10.6.8 and have downloaded all updates. When I go into finder, it says I have over 80 gigs available. Is there some other memory cache that I need to check? Thanks so much for your help.

ejwoodall wrote:
It's not a router problem as I explained in my post. If it was a router problem then I wouldn't have the problem everywhere I go. It is an issue with the software.
Then I guess the millions of people running 10.5.7 with no issues are just hallucinating that their machines are working fine?
I'm not trying to belittle your issues; you're certainly having them and I know first hand how annoying an intermittent AirPort issue can be. (In fact, mine was due to an AirPort driver bug that no one else seemed to suffer from.)
The single best diagnostic you could do is take your system running 10.5.7 to an Apple Store, and try using their in-store network.
If your machine performs flawlessly, it may be a router issue.
If your machine has connectivity issues there, it may be a hardware problem with your machine.
There have been numerous people in multiple threads over the years who swore that an update was buggy because things used to work, but returned later to sheepishly admit that they took their machine in, a problem was found and fixed, and now their Mac works flawlessly with the newer software.
But simply reinstalling 10.5.5 in no way means the explanation of how firmware bugs may be at play here is incorrect.
In the context of that explanation, all you've done is possibly reinstall software that asks to add "2 + 3."

Wireless Internet access via requires unplugging cable modem -

I have a brand new MacBook Pro with Snow Leopard (10.6.1) and Airport Express (7.4.2). I have high speed Internet via Comcast/cable modem. I spent 30 minutes with the Apple Tech Support folks and was finally able to get wireless internet access. However, after I shutdown and reboot, the only way I can wireless internet is to unplug the internet cable from both the wall plug and cable modem and unplug the modem, both for about two minutes. This isnt what I had in mind when I crossed over from the dark side (PC laptop world) and am having buyer's remorse. Does anyone know how I can fix this problem (i dont want to unplug cables before each session on the internet)?

Mr. Timmons,
Thank you so much for the response. I thought the complete reboot would work, but apparently not. I followed the directions precisely, even waiting a few minutes longer than suggested for each of the steps. My air express is still blinking yellow. I think the issue has something to do with the DHCP and the IP address which are diifferent. The IP address is one series of number (starts with 169), and the LAN IP address is another number (starts with 10). Status on airport express show yellow for internet connection, and yellow for no DSN servers. When I go to the internet tab of airport utility, it shows the iPv4 address starts wutg the 169 number. When I click on the network tab, the DHCP range starts with the 10 number. When I open the Network Options window, the iPv4 DHCP range starts with the 10 number. I am at a loss as to how to get them to match up (with either the 169 number or the 10 number). V/R sjbgtmo

Complete wireless internet access failure:(

Ok everyone, here is the low down for the last month.
I use a 2005 ibook G4, access internet and email set up w/ Mac Mail thru my airport card and jump on wireless cafe that i live next 2. For 3 whole months, i was set up and running internet and email perfectly. I didn't change any setting, service, etc. Except the network from cafe (from linksys to RGII).
1st: as of 1/1, i lost my ability to send email thru Mac mail using wireless access (thru cafe). Error was "port 25 timed out". After spending 4 days with ISP, setting- resetting POP account and outgoing server, pinging port 25 to verify sent, scanning port 25 to verify, etc, etc, etc. This produced no resolution.
2nd: as of 1/21, I have lost complete internet access. I have run the network diagnostic to fix, no go...
SO, I took my ibook to the Genius bar at Apple store for a looksy. Sure enough some setting were off or changed, (by my own troubleshooting). After everything was checked and reset, all was A-OK (at the Store). I could access internet, received AND send email. Yippee!
NOW here is the tricky part... as soon as i got home and turned her on, I could see the airport finding networks (RGII), But when I try to access email or internet (thru Mac Mail, safari) it says my ibook is not connected to internet, same for email. I run the network diagnostic, and it can't fix problem.
When I go next door to see if the cafe is having router problems on there end...Nope everyone is accessing the internet just fine:(
This is NOT a problem with password etc, As the cafe is set up with authentication as NONE. Plus everyone there is able to use the wireless access.
So what do you propose is my problem? Remember this was all working fine for 3 months and started to fall apart this last month. In addition, to having eveything work just fine at the Apple store a mere 30mins before.
Could this be an issue with the RGII network i am jumping on?
Why would I be the only person effected and not everyone at the cafe?
ibook Mac OS X (10.4.3) wireless access at cafes

Though it doesn't solve your issue, I thought I'd
share that I can access many non-Apple access points
(Cisco 1200's, Linksys WAP54G's for example) with OS
10.4.4. This being so, I think we're safe to assume
the issue is not related to a recent OS update.
I'm afraid I must disagree with this. Few months back, I lost my Airport connection when I installed the 10.4.3 System Update. Fixed by restoring from backup and going back to 10.4.3. Managed to upgrade to 10.4.4 successfully and maintain wireless connection to a Compex 802.11g base station. Then I made the mistake of accepting the Airport 2005-001 update. Immediately lost my Airport connection. Other PCs can connect to the base station, and I can access the internet by connecting my Powerbook to the router using Ethernet. Can even see the Airport network and login to the router's admin page over wireless. Only thing that doesn't work is connecting to the internet wirelessly.
Once I changed my base station to an older one I had lying around, I can connect wirelessly again and all seems well.
My conclusion is that Airport Update 2005-001 definitely broke compatibility between Airport Extreme and some 3rd party base stations. The irony is that this update was supposed to "improve" compatibility !

Internet access problem

Similar Messages

Maybe you are looking for