Internet Not working Properly.

When im using internet in my iPhone4 for a long time ( 2-4 Hours) then frequently the connectivity stopping the responce from server.
the safari displaying the massage that "the server could not responding".
it is happening when im in a good internet connectivity(Wi-Fi or 3G).
if i go to airplaine mode and come back then i can reconnect the internet .
what is happening with the server??

ISP (Internet Service Provider)
Here you go: http://support.apple.com/kb/ht1414
First restore, then call your ISP if issue persists.

Similar Messages

Internet not working properly in osx but fine in xp

I'm running OS X 10.5.6 and found that lots of websites just aren't loading up. For example I have to post this in xp as this part of the apple website just hangs.
Webmail also doesn't work, can't log onto hotmail, I can log onto yahoo but cant read messages or send mail via webmail. If I use the 'mail' program in OS X I can download all the mails and send very small mails of up to about 10 lines, any more than that and they just get stuck. I have tried Safari, Firefox and Seamonkey, also the Seamonkey mail client and all suffer the same problems.
The websites will just sit there loading and eventually time out.
I have XP home edition on bootcamp, if I reboot into that it's fine and I can access everything normally using both IE7 and firefox.
If I run the same xp partition using VMware fusion though I have the same problems as in OS X.
This problem was present in 10.5.5 and I was hoping it would be cured in 10.5.6... I guess not.
I read a lot of talk about dns problems so I manually added various dns servers but to no avail. The network settings are the same in xp as in os x (except for the dns servers I added).
Has anyone got any suggestions on this? I got a mac to escape windows, now its forcing me to use it >.<

I'm also having extreme problems with Flash. I did the
uninstaller thing too, I re-booted over & over again & it's
still not working. I can't view anything that uses Flash!!! It
shows up as being installed on my computer, but all the websites I
go to say "you don't have the new version installed-install now."
There's a link to install, I get the pop up on my toolbar to
install Active-X, but nothing happens.
If anyone has new info...please help

I have a Linksys WRV200 wireless router and the wireless signal is not working properly so I cannot connect to the internet wirelessly. the wireless light has a fast green blinking light. how can I fix the router?

I have a Linksys WRV200 wireless router and the wireless signal is not working properly so I am unable to connect to the internet wirelessly. The wireless light is blinking green very quickly and I connect and disconnect from the network constantly. How do I get the router to work properly

Hello James,
The flashing WLAN light means activity (data getting transferred). Try disconnecting all your devices and check whether the light is still flashing or disconnect the router from internet and do the check.
Do you have your SSID as linksys or the default one? If your neighbor has the same SSID, then traffic could result from your neighbor's one. Try changing your SSID and password. Make your security WPA/WPA2.
Hope this helps,
Thanks
Vijay

Flash player does not work properly on Windows 7 32 bits

Hello,
My flash player does not work properly on Windows 7 32 bits with Firfox and IE8 (lasts versions).
My Flash player version : 10.0.45.2, but I tried with version 9 too, with same problems.
I have tried to uninstall, reboot, reinstall several times, ... witch did not worked.
In fact, it works correctly on some sites, like youtube, but not on some others like :
http://www.dailymotion.com/ => black screen instead of videos, right click gives flash context menu
http://www.canalplus.fr/ => videos does not load, right click gives flash context menu
http://www.myspace.com/ => no audio player, right click gives flash context menu
some games in http://www.kongregate.com/ => black screen instead of games, right click gives flash context menu
I have no problem with shockwave in http://www.adobe.com/shockwave/welcome/
No problem too with flash player on http://www.adobe.com/software/flash/about/
But in the Global Privacy Settings panel (http://www.macromedia.com/support/documentation/en/flashplayer/help/settings_manager02.htm l), I cannot change any settings :
I cannot check boxes,
My changes are not saved.
In most of flash animations, videos, ...,
when I click on parameters, I cannot do anything, even closing.
when I am in full screen mode, the message "press escape to exit...." does not disappear.
Last thing, all those problems was not there when I was on Windows XP, few weeks ago, and appear with my registered Windows 7 premium familly edition, with the same hardware configuration...
Thank you for your help

Hi eidnolb
Thanks for your answer.
This is what I have :
Verify user permissions
I have an administrator account.
I tried (uninstall, install and run) with super-administrator account for same results
Install the most current version.
I am running the latest version (10.0.45.2)
Run the Clean Installer to Fix 3rd Party Flash Player Cleaners
I did not "clean" my computer.
Troubleshoot Pop-up blockers
I have no Pop-up or esle blocker software.
Ensure that Internet utilities do not block Flash Player
I tried (uninstall, install and run) without Avast.
I have windows 7 firewall. I do not know where I can allow ActiveX controls and Flash (SWF) content. I do not see anything relative to ActiveX an Flash in allowed program list.
Fix machine crashes when displaying Flash content
I have no freez or crash.
Using IE, Shockwave Flash Object is Enabled and vs 10.0.45.2
Using FF, I have SWF vs 10.0.45.2 and it is Enabled
I really do not understand !!
Thanks,
Ju'

WRT1900 AC V1 - Linksys is aware that the router is not working properly. Help spread the word.

I just had a conversation with Linksys' Customer Service via chat: Daphne L. J: Hello Fernando Paramo. My name is Daphne L..
Daphne L. J: Welcome to Linksys Global Chat. Is this your initial contact or do you have a case number?
You: Case number is 04971062
Daphne L. J: Please give me 3-5 minutes to pull up and review your case.
You: OK
Daphne L. J: Thank you.
You: I have a WRT1900 AC, V1. The router is not working properly. I have disconnections every few minutes.I already installed the new firmware version and I still have the same issues. I already reset the router to factory defaults and same issues. I have changed the settings back to my personal preferences: Changed the SSID, changed the wireless security settings, changed the DNS and deactivate WPS. That's it.I'm using 5 Ghz mode with my laptops (5 Ghz adapters) and 2-4 Ghz with a few devices (Chromecast, Nintendo 3DS).
Daphne L. J: Thank you for waiting.
Daphne L. J: Please confirm if the following information is correct:
Name : Fernando Paramo
Phone Number :
E-Mail Address :
Model Number : WRT1900AC
Serial Number : 13J10609406280
Country : United States
You: That's correct.
Daphne L. J: Okay. Were you able to check if the devices have stable connection wired to the router?
You: No. I do not have devices with Ethernet ports. Well, only the cable modem.
You: But the modem is fine. No disconnections from my ISP.
You: It is the router.
Daphne L. J: Alright. What is the current firmware version of your router?
You: I tried to return the router to Wal-Mart yesterday with no luck. This is a useless device. And I have been reading comments on the community forums and a lot of people are having problems.
Daphne L. J: We are actually aware of the issue and are working on a resolution. What is the current firmware version of your router?
You: Ver. 1.1.10.167514
You: Latest one.
Daphne L. J: Yes, so you reflashed the firmware, reset and then manually reconfigure it after, not using backup configuration, is that right?
You: That's correct.
Daphne L. J: And it is intermittent on all devices connected to both 2.4 and 5 Ghz networks, is that right?
You: That's correct.
Daphne L. J: Thank you for the information. Please give ,e 3-5 minutes to verify this with my superior.
Daphne L. J: Thank you for waiting.
You: I want to send you my WRT1900 AC and get a V2 or I want a EA8500 and pay the difference myseld.
You: I do not want my current hardware.
You: It is useless for my needs.
You: I can't believe I had an older E3000 that didn't give me any problems.
Daphne L. J: We have already exhausted all possible troubleshooting steps for your concern. As verified with my Supervisor, we will forward your case to our Customer Assurance Team. They are highly technical and knowledgeable when it comes to advanced troubleshooting. They will contact you in the next 24 to 48 hours. By the way, who is your Internet Service Provider? And do you Cable or DSL connection?
You: Cable connection.
Daphne L. J: Who is your Internet Service Provider?
You: A company called .
You: How are they going to contact me?
Daphne L. J: Alright. By the way, on the device itself, on its FCC ID, please check if you have WRT1900AC or WRT1900AC v2.
You: Are you paying attention to me?
You: I already told you it's V1.
Daphne L. J: They will call or email you. Please double check if these informations are correct:
Name :
Phone Number :
E-Mail Address :
You: I told you I want to send you my WRT1900 AC and get a V2 or I want a EA8500 and pay the difference myself.
You: I want them to contact me to my email. I can't answer the phone during work hours.
Daphne L. J: We can't assure you if we will be able to replace it with Version 2 or if you are allowed to have the EA8500 instead.
Daphne L. J: Just in case, do you also have an alternate number?
Daphne L. J: Also, what time zone are you in? And what is your preferred time and day for them to contact you?
You: I have the one from my office in Mexico. Central Time. Any time is good.
Daphne L. J: So, you are currently in Mexico?
You: I work in Mexico but I have the house in USA. I live in the border.
Daphne L. J: I see. Do you have any other questions or clarifications?
You: I live 10 minutes away from the International Bridge. But that's not an issue. I bought the router at Walmart in Laredo, TX.
Daphne L. J: Thank you for the information. Would that be all for now?
You: I want a clarification: Do you realize that there is an issue with the current WRT1900 AC? Are you aware of that?
You: Because this is a very expensive router that is not working as it should be.
Daphne L. J: Yes, we are aware of the issue and are working on a resolution.
Daphne L. J: Would there be anything else you need?
You: That would be it. I will wait for you to contact me.
You: Thanks.
Daphne L. J: Alright. Thank you for giving us an opportunity to serve you through Linksys Live Chat. You may also visit our support site at www.linksys.com. For your reference, your case number is 04980394. Thank you for choosing Linksys and have a great day! We paid $250 for this piece of equipment. That's a lot of money for a device that doesn't work. I just want to get a V2 replacement, or better yet, an exchange for a EA8500. We should all demand this. It is not fair for us. The current WRT1900 AC is a useless device. They even should do a recall of the product. I will wait for them to contact me, but I'm thinking if I should send the information to The Consumerist or someone else. What to do?

FernandoRocker wrote:
Well... instead of looking into this with Engineering, I would prefer you to talk about this with the Sales department and exchange my WRT1900AC for an EA8500 (I will pay the difference if needed). Seriously. The device is useless. Not just a paperweigt... an expensive paperweight.Actually I looking into the swap for you because I think that would be best in your case. Keep this in perspective. There is laterally millions of WRT1900AC V1 out there with very few issues with latest firmwares and of course the odd exception. In your case it could be a defective WRT1900AC.

WRT1900AC V1 - Linksys is aware that the router is not working properly. Help spread the word.

I just had a conversation with Linksys' Customer Service via chat: Daphne L. J: Hello Fernando Paramo. My name is Daphne L..
Daphne L. J: Welcome to Linksys Global Chat. Is this your initial contact or do you have a case number?
You: Case number is 04971062
Daphne L. J: Please give me 3-5 minutes to pull up and review your case.
You: OK
Daphne L. J: Thank you.
You: I have a WRT1900AC, V1. The router is not working properly. I have disconnections every few minutes.I already installed the new firmware version and I still have the same issues. I already reset the router to factory defaults and same issues. I have changed the settings back to my personal preferences: Changed the SSID, changed the wireless security settings, changed the DNS and deactivate WPS. That's it.I'm using 5 Ghz mode with my laptops (5 Ghz adapters) and 2-4 Ghz with a few devices (Chromecast, Nintendo 3DS).
Daphne L. J: Thank you for waiting.
Daphne L. J: Please confirm if the following information is correct:
Name : Fernando Paramo
Phone Number :
E-Mail Address :
Model Number : WRT1900AC
Serial Number : 13J10609406280
Country : United States
You: That's correct.
Daphne L. J: Okay. Were you able to check if the devices have stable connection wired to the router?
You: No. I do not have devices with Ethernet ports. Well, only the cable modem.
You: But the modem is fine. No disconnections from my ISP.
You: It is the router.
Daphne L. J: Alright. What is the current firmware version of your router?
You: I tried to return the router to Wal-Mart yesterday with no luck. This is a useless device. And I have been reading comments on the community forums and a lot of people are having problems.
Daphne L. J: We are actually aware of the issue and are working on a resolution. What is the current firmware version of your router?
You: Ver. 1.1.10.167514
You: Latest one.
Daphne L. J: Yes, so you reflashed the firmware, reset and then manually reconfigure it after, not using backup configuration, is that right?
You: That's correct.
Daphne L. J: And it is intermittent on all devices connected to both 2.4 and 5 Ghz networks, is that right?
You: That's correct.
Daphne L. J: Thank you for the information. Please give ,e 3-5 minutes to verify this with my superior.
Daphne L. J: Thank you for waiting.
You: I want to send you my WRT1900AC and get a V2 or I want a EA8500 and pay the difference myseld.
You: I do not want my current hardware.
You: It is useless for my needs.
You: I can't believe I had an older E3000 that didn't give me any problems.
Daphne L. J: We have already exhausted all possible troubleshooting steps for your concern. As verified with my Supervisor, we will forward your case to our Customer Assurance Team. They are highly technical and knowledgeable when it comes to advanced troubleshooting. They will contact you in the next 24 to 48 hours. By the way, who is your Internet Service Provider? And do you Cable or DSL connection?
You: Cable connection.
Daphne L. J: Who is your Internet Service Provider?
You: A company called .
You: How are they going to contact me?
Daphne L. J: Alright. By the way, on the device itself, on its FCC ID, please check if you have WRT1900AC or WRT1900AC v2.
You: Are you paying attention to me?
You: I already told you it's V1.
Daphne L. J: They will call or email you. Please double check if these informations are correct:
Name :
Phone Number :
E-Mail Address :
You: I told you I want to send you my WRT1900AC and get a V2 or I want a EA8500 and pay the difference myself.
You: I want them to contact me to my email. I can't answer the phone during work hours.
Daphne L. J: We can't assure you if we will be able to replace it with Version 2 or if you are allowed to have the EA8500 instead.
Daphne L. J: Just in case, do you also have an alternate number?
Daphne L. J: Also, what time zone are you in? And what is your preferred time and day for them to contact you?
You: I have the one from my office in Mexico. Central Time. Any time is good.
Daphne L. J: So, you are currently in Mexico?
You: I work in Mexico but I have the house in USA. I live in the border.
Daphne L. J: I see. Do you have any other questions or clarifications?
You: I live 10 minutes away from the International Bridge. But that's not an issue. I bought the router at Walmart in Laredo, TX.
Daphne L. J: Thank you for the information. Would that be all for now?
You: I want a clarification: Do you realize that there is an issue with the current WRT1900AC? Are you aware of that?
You: Because this is a very expensive router that is not working as it should be.
Daphne L. J: Yes, we are aware of the issue and are working on a resolution.
Daphne L. J: Would there be anything else you need?
You: That would be it. I will wait for you to contact me.
You: Thanks.
Daphne L. J: Alright. Thank you for giving us an opportunity to serve you through Linksys Live Chat. You may also visit our support site at www.linksys.com. For your reference, your case number is 04980394. Thank you for choosing Linksys and have a great day! We paid $250 for this piece of equipment. That's a lot of money for a device that doesn't work. I just want to get a V2 replacement, or better yet, an exchange for a EA8500. We should all demand this. It is not fair for us. The current WRT1900AC is a useless device. They even should do a recall of the product. I will wait for them to contact me, but I'm thinking if I should send the information to The Consumerist or someone else. What to do?

Hello. I sent my WRT1900AC V1 to Linksys four days ago (Monday) via UPS with a RMA. Linksys paid the shipping and everything. The router is still in route, and it should arrive to their offices tomorrow. Once they receive the WRT1900 AC V1, they are going to send me an EA8500 as a replacement. But I have been reading the comments about the EA8500 here in the forum and it seems to have the same problems. I guess the firmware is extremely flawed in both routers (maybe it is almost the same code?). Anyway, I will try the EA8500 and I hope it works. I bought a temporary router from Walmart and I paid $35 for it. It is a Belink N600 DB. I can't believe that a $35 router is working a lot, lot, lot better than my previous $250 WRT1900AC router. Unbelievable. If the EA8500 doesn't work, I'm going to try and get my money back from Linksys, or contact The Consumerist or someone to get my money back and get a Nighthawk instead.

Not working properly Computer Browser service in Windows Server 2012

Good afternoon.
Migrated from 2003 to 2012 Active Directory, all is good, but the service Computer Browser in Windows Server 2012 is not working properly.
Online, there are several hundred computers, one network, no segments. PDC is the Master Browser, it is in my list of all the computers, but gives customers or Backup Browser computers only part, and in alphabetical order, giving the first 70 computers and
all.
Looked packet sniffer:
Microsoft Windows Lanman Remote API Protocol
Entry Count: 70
Available Entries: 251
So on Master Browser shows 251 computer, and the client 70.
If disabled on Windows Server 2012 Service Computer Browser, Master Browser is a computer running Windows Server 2003. He gives all computers.
What is the problem, how to get Windows Server 2012 to work correctly as a Master Browser?

More info. I have high lighted in bold where the issue is. This is a massive headache for me at the moment
Frame: Number = 377, Captured Frame Length = 182, MediaType = ETHERNET
- Ethernet: Etype = Internet IP (IPv4),DestinationAddress:[00-13-72-52-6E-A1],SourceAddress:[00-1E-0B-2B-68-DD]
- DestinationAddress: Dell Inc. 526EA1 [00-13-72-52-6E-A1]
     Rsv: (000000..)
     UL: (......0.) Universally Administered Address
     IG: (.......0) Individual address (unicast)
- SourceAddress: 001E0B 2B68DD [00-1E-0B-2B-68-DD]
     Rsv: (000000..)
     UL: (......0.) Universally Administered Address
     IG: (.......0) Individual address (unicast)
    EthernetType: Internet IP (IPv4), 2048(0x800)
- Ipv4: Src = 10.44.46.101, Dest = 10.44.44.14, Next Protocol = TCP, Packet ID = 14025, Total IP Length = 168
- Versions: IPv4, Internet Protocol; Header Length = 20
     Version:      (0100....) IPv4, Internet Protocol
     HeaderLength: (....0101) 20 bytes (0x5)
- DifferentiatedServicesField: DSCP: 0, ECN: 0
     DSCP: (000000..) Differentiated services codepoint 0
     ECT: (......0.) ECN-Capable Transport not set
     CE:   (.......0) ECN-CE not set
    TotalLength: 168 (0xA8)
    Identification: 14025 (0x36C9)
- FragmentFlags: 16384 (0x4000)
     Reserved: (0...............)
     DF:       (.1..............) Do not fragment
     MF:       (..0.............) This is the last fragment
     Offset:   (...0000000000000) 0
    TimeToLive: 128 (0x80)
    NextProtocol: TCP, 6(0x6)
    Checksum: 0 (0x0)
    SourceAddress: 10.44.46.101
    DestinationAddress: 10.44.44.14
- Tcp: Flags=...AP..., SrcPort=65372, DstPort=NETBIOS Session Service(139), PayloadLen=128, Seq=1910965363 - 1910965491, Ack=580319796, Win=252 (scale factor 0x8) = 64512
    SrcPort: 65372
    DstPort: NETBIOS Session Service(139)
    SequenceNumber: 1910965363 (0x71E70473)
    AcknowledgementNumber: 580319796 (0x2296FA34)
- DataOffset: 80 (0x50)
     DataOffset: (0101....) 20 bytes
     Reserved:   (....000.)
     NS:         (.......0) Nonce Sum not significant
- Flags: ...AP...
     CWR:    (0.......) CWR not significant
     ECE:    (.0......) ECN-Echo not significant
     Urgent: (..0.....) Not Urgent Data
     Ack:    (...1....) Acknowledgement field significant
     Push:   (....1...) Push Function
     Reset: (.....0..) No Reset
     Syn:    (......0.) Not Synchronize sequence numbers
     Fin:    (.......0) Not End of data
    Window: 252 (scale factor 0x8) = 64512
    Checksum: 0x6F65, Disregarded
    UrgentPointer: 0 (0x0)
    TCPPayload: SourcePort = 65372, DestinationPort = 139
- Nbtss: SESSION MESSAGE, Length =124
    PacketType: SESSION MESSAGE, 0(0x00)
- Flags: Add 0 to Length
     Reserved: (0000000.)
     Extension: (.......0)Add 0 to Length
    Length: 124(0x7C)
- SMB: C; Transaction, Remote Administration Protocol, FileName = \PIPE\LANMAN
    Protocol: SMB
    Command: Transaction 37(0x25)
- NTStatus: 0x0, Facility = FACILITY_SYSTEM, Severity = STATUS_SEVERITY_SUCCESS, Code = (0) STATUS_SUCCESS
     Code:     (................0000000000000000) (0) STATUS_SUCCESS
     Facility: (...0000000000000................) FACILITY_SYSTEM
     Customer: (..0.............................) NOT Customer Defined
     Severity: (00..............................) STATUS_SEVERITY_SUCCESS
- SMBHeader: Command, TID: 0x2001, PID: 0x276C, UID: 0x3801, MID: 0x0140
   - Flags: 24 (0x18)
      LockAndRead:     (.......0) LOCK_AND_READ and WRITE_AND_UNLOCK NOT supported (Obsolete) (SMB_FLAGS_LOCK_AND_READ_OK)
      NoAck:           (......0.) An ACK response is needed (SMB_FLAGS_SEND_NO_ACK[only applicable when SMB transport is NetBIOS over IPX])
      Reserved_bit2:   (.....0..) Reserved (Must Be Zero)
      CaseInsensitive: (....1...) SMB paths are case-insensitive (SMB_FLAGS_CASE_INSENSITIVE)
      Canonicalized:   (...1....) Canonicalized File and pathnames (Obsolete) (SMB_FLAGS_CANONICALIZED_PATHS)
      Oplock:          (..0.....) Oplocks NOT supported for OPEN, CREATE & CREATE_NEW (Obsolete) (SMB_FLAGS_OPLOCK)
      OplockNotify:    (.0......) Notifications NOT supported for OPEN, CREATE & CREATE_NEW (Obsolete) (SMB_FLAGS_OPLOCK_NOTIFY_ANY)
      FromServer:      (0.......) Command - SMB is being sent from the client (SMB_FLAGS_SERVER_TO_REDIR)
   - Flags2: 51207 (0xC807)
      KnowsLongFiles:            (...............1) Understands Long File Names (SMB_FLAGS2_KNOWS_LONG_NAMES)
      KnowsEas:                  (..............1.) Understands extended attributes (SMB_FLAGS2_KNOWS_EAS)
      SmbSecuritySignature:      (.............1..) Security signatures enabled (SMB_FLAGS2_SMB_SECURITY_SIGNATURE)
      Compressed:                (............0...) Compression Disabled for REQ_NT_WRITE_ANDX and RESP_READ_ANDX (SMB_FLAGS2_COMPRESSED)
      SecuritySignatureRequired: (...........0....) Security Signatures are NOT required (SMB_FLAGS2_SMB_SECURITY_SIGNATURE_REQUIRED)
      Reserved_bit5:             (..........0.....) Reserved (Must Be Zero)
      IsLongName:                (.........0......) DO NOT use Long File Names (SMB_FLAGS2_IS_LONG_NAME)
      Reserved_bits7_9:          (......000.......) Reserved (Must Be Zero)
      ReparsePath:               (.....0..........) NOT a Reparse path (SMB_FLAGS2_REPARSE_PATH)
      ExtendedSecurity:          (....1...........) Aware of extended security (SMB_FLAGS2_EXTENDED_SECURITY)
      Dfs:                       (...0............) NO DFS namespace (SMB_FLAGS2_DFS)
      Paging:                    (..0.............) Read operation will NOT be permitted unless user has permission (NO Paging IO) (SMB_FLAGS2_PAGING_IO)
      NTStatus:                  (.1..............) Using 32-bit NT status error codes (SMB_FLAGS2_NT_STATUS)
      Unicode:                   (1...............) Using UNICODE strings (SMB_FLAGS2_UNICODE)
     PIDHigh: 0 (0x0)
     SecuritySignature: 0x0
     Unused: 0 (0x0)
     TreeID: 8193 (0x2001)
     ProcessID: 10092 (0x276C)
     UserID: 14337 (0x3801)
     MultiplexID: 320 (0x140)
- CTransaction:
     WordCount: 14 (0xE)
     TotalParameterCount: 32 (0x20)
     TotalDataCount: 0 (0x0)
     MaxParameterCount: 8 (0x8)
     MaxDataCount: 4200 (0x1068)
     MaxSetupCount: 0 (0x0)
     Reserved: 0 (0x0)
   - Flags: Do NOT disconnect TID
      Disconnect: (...............0) Do NOT disconnect TID
      NoResponse: (..............0.) Server response to the client
      Reserved:   (00000000000000..) Reserved
     Timeout: 5000 milli sec(s)
     Reserved2: 0 (0x0)
     ParameterCount: 32 (0x20)
     ParameterOffset: 92 (0x5C)
     DataCount: 0 (0x0)
     DataOffset: 0 (0x0)
     SetupCount: 0 (0x0)
     Reserved3: 0 (0x0)
     ByteCount: 61 (0x3D)
   - RemoteAPIBuffer:
    - FileName: \PIPE\LANMAN
     - Align: 1 Bytes
        AlignBytes: Binary Large Object (1 Bytes)
       Name: \PIPE\LANMAN
      Pad1: Binary Large Object (2 Bytes)
- RAPRequest: NetServerEnum2 Request, InfoLevel = 1, SV_TYPE_ALL: All in NSNET
    RAPOpcode: NetServerEnum2
- ParameterDescriptor: WrLehDz; 4 send, 1 receive parameter
     Param: (W) WORD (send parameter, 16 bit integer)
     Param: (r) Receive buffer (format in data descriptor) (receive data, 0 bit integer)
     Param: (L) Receive buffer length (send/receive parameter, 16/16 bit integer)
     Param: (e) Entries read (receive data, 0 bit integer)
     Param: (h) WORD (receive parameter, 16 bit integer)
     Param: (D) DWORD (send parameter, 32 bit integer)
     Param: (z) ASCIIZ (send parameter, 8 bit integer)
     Param: ASCII NUL (string terminator)
- DataDescriptor: B16BBDz; data bytes send: 0, receive: 34
   - Datum: (B) BYTE[16] (receive data, 8 bit integer)
      Datum: (B) BYTE (receive data, 8 bit integer)
      Digit: 1
      Digit: 6
     Datum: (B) BYTE (receive data, 8 bit integer)
     Datum: (B) BYTE (receive data, 8 bit integer)
     Datum: (D) DWORD (receive data, 32 bit integer)
     Datum: (z) ASCIIZ* (receive data offset, 32 bit integer)
     Datum: ASCII NUL (string terminator)
- NetServerEnum2: SV_TYPE_ALL: All in NSNET
     InfoLevel: (1) SERVER_INFO_1
     ReceiveBufferSize: 4200 (0x1068)
   - ServerType: SV_TYPE_ALL: All
      Workstation:      (...............................1) All workstations
      Server:           (..............................1.) All computers with the server service running
      Sqlserver:        (.............................1..) All running Microsoft SQL Server
      DomainCtrl:       (............................1...) All primary domain controllers
      DomainBakctrl:    (...........................1....) All backup domain controllers
      TimeSource:       (..........................1.....) All Time servers
      AFP:              (.........................1......) All Apple File Protocol servers
      Novell:           (........................1.......) All Novell servers
      DomainMember:     (.......................1........) All LAN Manager 2.x domain members
      PrintqServer:     (......................1.........) All print servers
      DialinServer:     (.....................1..........) All dial-in servers
      ServerUnix:       (....................1...........) All Unix/Xenix servers
      NT:               (...................1............) All Windows NT workstations or servers
      WFW:              (..................1.............) All Windows for Workgroups servers
      ServerMFPN:       (.................1..............) All Microsoft File and Print for NetWare servers
      ServerNT:         (................1...............) All non-domain controller servers
      PotentialBrowser: (...............1................) All servers that can run the browser service
      BackupBrowser:    (..............1.................) All backup browsers
      MasterBrowser:    (.............1..................) All master browsers
      DomainMaster:     (............1...................) All domain master browsers
      Reserved1:        (..........11....................)
      Windows:          (.........1......................) All Windows 95 or later
      DFS:              (........1.......................) All DFS root servers
      ClusterNT:        (.......1........................) All NT Clusters
      Terminalserver:   (......1.........................) All Terminal Servers
      ClusterVSNT:      (.....1..........................) All NT Cluster Virtual Server Names
      DCE:              (....1...........................) AllIBM DSS (Directory & Security Services)
      Reserved2:        (...1............................)
      AlternateXport:   (..1.............................) Return list for alternate transport
      LocalListOnly:    (.1..............................) Return local list only
      DomainEnum:       (1...............................) Enumerate primary domain
     Domain: NSNET
Then the reply;
   Frame: Number = 378, Captured Frame Length = 1514, MediaType = ETHERNET
+ Ethernet: Etype = Internet IP (IPv4),DestinationAddress:[00-1E-0B-2B-68-DD],SourceAddress:[00-13-72-52-6E-A1]
+ Ipv4: Src = 10.44.44.14, Dest = 10.44.46.101, Next Protocol = TCP, Packet ID = 27036, Total IP Length = 1500
+ Tcp: Flags=...A...., SrcPort=NETBIOS Session Service(139), DstPort=65372, PayloadLen=1460, Seq=580319796 - 580321256, Ack=1910965491, Win=253 (scale factor 0x8) = 64768
+ Nbtss: SESSION MESSAGE, Length =2013
+ SMB: R; Transaction, Remote Administration Protocol
- RAPResponse: NetServerEnum2 Response, Count = 31
    Win32ErrorCode: 0x00000000 - ERROR_SUCCESS - The operation completed successfully.
    Converter: 2251 (0x8CB)
- NetServerEnum2: Count = 31
     EntriesReturned: 31 (0x1F)
     EntriesAvailable: 31 (0x1F)
   + NetServerInfo1: APOLLO
   + NetServerInfo1: ARTEMIS
   + NetServerInfo1: ASKLEPIOS
   + NetServerInfo1: CASTOR
   + NetServerInfo1: DCC4503-131L
   + NetServerInfo1: DCC4503-155L
   + NetServerInfo1: DCC4503-157L
   + NetServerInfo1: DCC4503-161L
   + NetServerInfo1: DCC4503-171L
   + NetServerInfo1: DCC4503-172L
   + NetServerInfo1: DCC4503-175L
   + NetServerInfo1: DCC4503-177L
   + NetServerInfo1: DCC4503-183L
   + NetServerInfo1: DCC4503-184L
   + NetServerInfo1: DCC4503-185L
   + NetServerInfo1: DCC4503-188L
   + NetServerInfo1: DCC4503-196L
   + NetServerInfo1: DCC4503-197L
   + NetServerInfo1: DCC4503-199L
   + NetServerInfo1: DCC4503-202L
   + NetServerInfo1: DCC4503-203L
   + NetServerInfo1: DCC4503-205L
   + NetServerInfo1: DCC4503-210L
   + NetServerInfo1: DCC4503-213L
   + NetServerInfo1: DCC4503-219L
   + NetServerInfo1: DCC4503-220L
   + NetServerInfo1: DCC4503-228L
   + NetServerInfo1: DCC4503-233L
   + NetServerInfo1: DCC4503-234L
   + NetServerInfo1: DCC4503-236L
   + NetServerInfo1: DCC4503-241L
    StringData: Binary Large Object (586 Bytes)

Html is not working properly

i was trying to work on texteditor to code a simple html page but its not working properly like the shows only two color on the background that are green and black
i dont know whats the issue but it use to work fine in mountain lion
i have even tried to use color code still it didnt work then i re-installed the os but the same problem again!
is there any special setting ?
i have change it to plain text and traditional html ..
thank you

Hi,
Do you really think it applies to all these:-
Categories: Accessibility, Boot Camp, Finder Tabs & Tags, iCloud Keychain, iMessage & Messages, Internet & Wi-Fi, Installation, Migration & Setup, Mail, Contacts & Calendar, Maps, Multiple Displays, Printing, Users & Groups, Using OS X Mavericks
Tags:wireless, backup, ical, screen, email, duplicate, printer, preferences, time,
hard, login, restart, vpn, font, dvd, excel, kernel, address, migration, mode, locked,
dvd_problem, hdd, thunderbolt, gray
It would be useful to see the HTML code you are using.
It would also useful to know which version of HTML you are using to do that.
8:57 pm Wednesday; March 12, 2014
 iMac 2.5Ghz i5 2011 (Mavericks 10.9)
 G4/1GhzDual MDD (Leopard 10.5.8)
 MacBookPro 2Gb (Snow Leopard 10.6.8)
 Mac OS X (10.6.8),
 Couple of iPhones and an iPad

Gadgets not working properly in windows 7

For some reason the gadgets in windows 7 are not working properly. I can open the gadget gallery and select a gadget, but it doesn't show the entire thing. For example i select the clock, and all it shows is a black square with the red ticking hand frozen. Another example is the CPU meter. All it shows when i click on it is a little white square where the meter should be. I can still close the gadgets by way of the close button on each gadget though (the calendar doesn't appear at all). UAC is turned on and i have rebooted the pc, same thing still happening. (It is Enterprise edition if that makes any difference). If anyone could help that would be great!

Have you come across the problem where some of the Gadgets that you added to the Sidebar/Desktop are not displayed correctly? For example, the clock gadget may be displayed as a black square containing only the "seconds" hand. Other gadgets may show up as
white rectangles with an information (i) icon and a plus sign. The settings button next to the gadget does not work, but the
x to close does. Here are some screenshots:
The above-mentioned behavior is caused due to the following reasons:
A subkey with foreign/ASCII character exists under the "Zones" registry key.
XML registration is missing in the system.
Use these steps to fix the problem:
Fix for Case 1
1. Click Start, type Regedit.exe and press {ENTER}
2. Navigate to the following branch:
HKEY_CURRENT_USER \ Software \ Microsoft \ Windows \ CurrentVersion \ Internet Settings \ Zones
3. Under the Zones key, delete the subkey shown with an ASCII character:
4. Exit the Registry Editor.
5. Logoff and login back to your user account.
Fix for Case 2
1. Open an
elevated Command Prompt window. To open an elevated (admin) Command Prompt, click Start, click All Programs, click Accessories,
right-click Command Prompt, and then click Run as administrator.
2. In the Command Prompt window, type the following command and press ENTER:
regsvr32 msxml3.dll
3. Similarly, run these commands:
regsvr32 scrrun.dll
regsvr32 jscript.dll
You should see the DllRegisterServer in <filename> succeeded message for each command executed.
4. Logoff and login back to your user account and see if the Gadgets display correctly.

SWF file not working properly in Explorer

I have made a kind of slide show showing jpg images loaded
from the web in an swf file, and it will not work properly. It is
my first .swf application, and I am using the free downloadable
FlashObject.js to load the swf into the browser. The problem is
that it sometimes loads perfectly, while other times it will not
work at all! It is not the paths, because I have tried setting the
images in the same directory as the swf, and not importing the
image names thru flashVars. What drives me mad is that it works
consistently in Explorer, the first time I load it, and the first
time after I have cleared the temporary internet files. Otherwise
it will not load at all. In Firefox however, if randomly fails to
load about one time out of ten or something like that. The code is
compiled using the free downloadable compiler. Anyone have any idea
what may be wrong?

I may be late but better late then...
Not true
You can nest hundreds of layers as long as all symbols are graphics.
People try to use a Movie symbol and this is script executed.
I am animator on cartoon all done in flash and we have dozens or more NESTS!!!!
Eyes inside of head inside of Character in car on stage...
many
Trick to not crashing is in FLASH
Set publish settings to FLASH 8.
Never use FLASH 9 with Actionsscript 3... This adds a lot of instability.
1 of these swfs in a project could kill it.
I render SWF at 30fps at 1920x1080 then into AE, then scale down to SD wide screen resolution 720x480 16x9.. set scale to 45.5 x 44.5 percent.
I output final animation at Quicktime ANIMATION 100 millions of colors... 1.21 (16x9)audio added at 48k
I have hundreds of hours trying to make this work reliably and finally I got the mix.
Then I take QT to Premiere for final edit, audio and titles.
Good luck
NATMAX

I am using firefox 3.6.17 i upgraded it to 4.1.but it does not work properly sometimes it opens every website and most of the time it does not work . so what is the problem please help . thank you

i am using firefox 3.6.17 i upgraded it to 4.1.but it does not work properly sometimes it opens every website and most of the time it does not work . so what is the problem please help . thank you

Did you check your security software (firewall)?
A possible cause is security software (firewall) that blocks or restricts Firefox or the plugin-container process without informing you, possibly after detecting changes (update) to the Firefox program.
Remove all rules for Firefox from the permissions list in the firewall and let your firewall ask again for permission to get full unrestricted access to internet for Firefox and the plugin-container process.
See:
* [[Server not found]]
* [[Firewalls]]

Flash players not working properly

hi there, since i have reinstalled my laptop, i am having
problem watching online videos properly, its like sounds comes
perfect, the video slows down and even stuck, cant watch whats
going on in the video. Could you please guide me how to rectify
this problem. The video streaming is not working properly as the
sound streaming is fine. Our internet is fine as its been check on
another Laptop and a Desktop Machine. Kindly reply me back asap.
Many thanks.
Regards,

Hi Harvardbothun-
I still don't know what "reinstalled my laptop means". Put it
back on your lap? Humor...arr-arr.
Anyway, you have Firefox with the latest FP10 plug-in. Have
you verified this with the "Version Tester"
http://www.adobe.com/software/flash/about/
and checked the support pages at
http://www.adobe.com/support/flashplayer/
I ask these questions not to be mean, but to verify your
version and make you aware of the differences between IE FP
(ActiveX) and FF FP (plug-in). Also... the version checker will act
funky if you have 2 different FP versions installed, such as your
XP's OE IE and your added FF. Look in Control Panel, Add/Remove
Programs. Do you see a previous version of FP there? You may need
to update your IE's FP as well, it could be conflicting with your
FFFP.
Another thing to check.... AVG8's Linkscanner has caused some
issues, mostly by slowing down site-loading. To test this, turn
off/diable that feature. Yes, it'll whine about it. (end of part 1)

This page contains some SWF objects that may not work properly...

Hello Guys
I bought this menu made by f-source into my page:
http://beta.asphalt-driveway-sealing.com/, it's working fine except I got this message each time I am opening my file with dreamweaver CS4: 'this page contains some SWF objects that may not work properly in the most recent versions of Internet Explorer. Dreamweaver cannot convert them to the new SWF markups. Please delete each of them and insert again' and what I did but still got this message
the developer told me that: "I previous versions of Dreamweaver you could disable the Active
Content Converter http://f-source.com/before_insert/
In CS4 there is no such option."
Please let me know what can I do then.
Many Thanks, T&T

Hi
CS4 uses a 'nested' type of object code to insert swf/flv files, which is more compliant than previous code. Obviously the f-source extension is not cs4 compliant if it is changing this, (the message indicates it is doing so) and is something you should pursue via there support department. However even though it is giving you this message it should still work on live pages.
PZ
www.pziecina.com

IPhone 5 mobile internet not working - tried everything

Mobile internet on my iPhone is not working properly, regardless of the protocol (edge or 3G). It's the strangest problem possible and so far I've tried everything to fix the problem, but nothing helps.
Here's the deal:
- when I switch from wi-fi to 3G/E, everythings seems normal (there's the sign 3G or edge on the screen), but there is no internet connection
- I have to go to settings, switch off 3G and switch it back on and the internet starts working. It solves the problem also if there's only edge signal, which makes it even more strange.
- when I switch back to wi-fi and then again back to mobile network, the same problem occurs and the same solutions applies
- the same happens when I drive in my car and the phone switches between two carrier's antennas or if I switch on the airplane mode/reset the phone
I've used the iPhone since it came out and had every version, so I consider myself an advanced user. In order to try to solve the problem I tried everything possible:
- checked cellular data information
- reset network settings
- restored the phone
- updated the iOS
- manually deleted cellular data and entered it again
- went to my carrier to get a new sim card
- had the carrier analyze the problem on a case study (I sent over location data and time), but they found no mistakes on the network
- went to Apple and got my iPhone replaced TWICE
So I eliminated the following:
- settings error
- carrier error
- hardware error
The only thing I have left now is the exorcist.

Same issue

Bootcamp 3.2: Microsoft Virtual WiFi MiniPort Adapter shows "device is not working properly...Code 31"

Using Windows 7 Enterprise 64-bit, Microsoft Virtual WiFi Miniport Adapter shows the "device is not working properly because Windows cannot load the drivers required for this device. (Code 31).".The device is the Apple iMac10,1 All-in-one computer. Right clicking browse files (for the device) shows the Bootcamp (C:), DVD (D:); and my external hard drives can be selected.
Internet and WiFi connections all working ok. Am also running MacDrive 8 to access the Mac drives when in the Windows partition, again without any seeming issues.
Updating the driver simply generates another Code 31 error.
Appreciate this seems to be a known problem - is the a solution a novice use might be able to follow or should I simply ignore the error message?
Driver Date us 21/06/2006 and Driver Version is 6.1.7600.16385.

Hi ,
Thank you for visiting the HP Support Forums and Welcome. It is a great site for information and questions. I have looked into your issue about your HP ENVY 4-1204tx Ultrabook and issues with WiFi adapter is not working properly. Error codes in Device Manager in Windows 8.1 could be fixed by deleting any extra drivers. So I would uninstall all that is listed in the Network drivers in the Device Manager, restart the Notebook. Here is a list of Device Manager options, this might help.
Here is a link to the HP Support Assistant if you need it. Just download and run the application and it will help with the software and drivers on your system that need updating or reinstalling. Hope this helps. Thanks.

Internet Not working Properly.

Similar Messages

Maybe you are looking for