Internet problem Express AND Extreme

Hi Airporters,
I have this problem, I can't find an answer to.
I have an Airport Extreme working fine with one Mac Pro, a MacBook Pro and Some XP's.
Since a third XP did not connect with Extreme (don't ask me why), I use an Airport Express, and now....it almost works.
The XP says it's connected to the Airport Network, but it does NOT give a connection to the Internet.
I tried to configure it all over again, but to no avail. What can I be doing wrong?
Thanx in advance.
Carlo
O yeah, everything = wireless

Hi Tesserax,
Sorry, I was away for a while (and will be away after tomorrow)...but still, thanks for your reply.
Yes, I guess the PC contains the problem. Moreover, while writing this answer I wanted to check what type of Linksys I had, and saw that in the system profile this Linksys was disabled or so. I enabled it, and yesssss....it worked
At that time there were two connections running (???!!!???), so I switched off the old one, and now the whole family is happy.
Thank you, you pushed me to the answer.
Carlo

Similar Messages

Problems with Airport Express and Extreme

I have tried to set up Airport Express and Extreme. Both proceeded normally in the Air Port Utility until the final stages. Then it said it couldn't find the devices. When I tried again (many times), I couldn't even start the process, even though it did that the first time for both. I'm stumped.

To set up the 802.11n AirPort Extreme Base Station (AEBSn) as a bridge, either connect to the AEBSn's wireless network or temporarily connect your computer directly (using an Ethernet cable) to one of the LAN port of the AEBSn, and then, using the AirPort Utility, make these settings:
AirPort Utility > Select the AEBSn > Manual Setup > Internet > Internet Connection tab
Connection Sharing: Off (Bridge Mode)
Click Update to apply the new settings
AirPort Express Base Station (AX) - iTunes Setup
Either connect to the AX's wireless network or connect directly, using an Ethernet cable, to the Ethernet port of the AX, and then using the AirPort Utility in "Manual Setup" mode, make the following changes:
AirPort Utility > Select the AX > Manual Setup > AirPort > Wireless
Wireless Mode: Join a wireless network
Network Name: <existing AEBSn's wireless network>
Wireless Security: <select the encryption type of the existing wireless network>
Wireless Password: <enter the existing wireless network password>
Verify Password: <re-enter the existing wireless network password>
AirPort Utility > Select the AX > Manual Setup >Music
Enable AirPlay (checked)
iTunes Speaker Name: <enter desired speaker name>
iTunes Speaker Password: (optional)
Verify Password: (optional)
Click Update to write the new settings to the AX

Airport Admin loses Express and Extreme, no iTunes, no Network Printer

Ever since I have upgraded to Tiger, I’ve experienced a strange, random Airport Extreme/Express problem which I have not been able to solve. I can sometimes replicate the problem but never consistently.
Laptop Configuration: 15” Powerbook G4 running Mac OS Tiger 10.4.3 with most current patches. System is stable and manifests no problems.
Airport Network Configuration: Network is closed with 128bit WEP encryption. No other laptops attached to the network besides my Powerbook.
Base Station: Airport Express attached to DSL modem with “Distribute IP Addresses” checkbox enabled, running firmware v6.2, stereo speakers plugged into audio jack. Network access is restricted by MAC address; RADIUS not in use, default IP address scheme is used.
Remote Base Station: Airport Extreme running firmware v5.6. The Extreme hosts a HP 1012 LaserJet printer plugged into the USB port and an IP phone plugged into the LAN port.
The Express and Extreme are within 15 feet of each other and enjoy a clear, strong 802.11b/g wireless signal on Channel 1 with a multicast setting of 11, interface robustness enabled and transmit power set to 100%.
Symptoms: iTunes loses its remote speakers setting; I cannot print to the network printer attached via USB to Airport Extreme; Airport Extreme and Express do not appear in Airport Admin Utility….yet I can access the network via the Powerbook, I have full internet access and IP phone can make calls. I just can’t print to the network printer or use AirTunes.
Troubleshooting: I can restore all functionality if I perform a hard reset of the Airport Express Base Station then re-import my saved Airport Express base station configuration settings. I typically look at the Airport Admin Utility to determine if functionality has been restored. If both the Airport Express and Extreme appear in the Admin utility, all is well. If they are not there, sometimes a laptop reboot will restore them, other times they will not appear when the Admin Utility is opened or when I rescan. If a rescan fails, I can access the Express and Extreme by typing in the IP address and password. Then each will show up in the Admin Utility and I can make changes and restart the devices. Even with a device restart, they will not automatically appear in the Admin Utility.
I first thought the problem was associated with the laptop going to sleep but this is not the case. Sometimes when I reset the Base Station, re-import the configs and reboot the laptop, I am able to automatically see the Express and Extreme in the Airport Admin Utility. Other times I can’t. Sometimes my settings will last a few days and I’ll enjoy full functionality then they will disappear. Other times they will disappear immediately, even with a reboot and a reset of the Express and Extreme.
If I use a 3rd party utility called Cocktail and reboot, I can restore functionality. Cocktail will delete all user, system and kernel caches, delete all log files, rerun disk permissions, and run the daily, weekly and monthly Apple Kron maintenance scripts. If I reboot after running Cocktail, my Airport Extreme and Express appear in the Admin Utility. Thus, I think the problem may be associated with a Airport Extreme cache file becoming corrupted or deleted upon reboot…….but I am not positive.
If there are any Airport experts out there, let me know what you think. I love Apple, I love my Mac and my little Airport Network…….but this is ******’ me off! Thus my plea for advanced geekery review and assistance.
Talk to me!

If the Airport Admin Utility cannot automatically "see" your Base Station, you have a big clue as to the cause of your problems. On a private LAN, it should never be necessary to select "Other" and manually type in the Base Station's IP address.
The most likely cause for the Airport Admin Utility not being able to automatically "see" an Airport Base Station - is a firewall on the Mac that is blocking it. Any of the following are possible:
- you have installed non-Apple firewall software on the Mac
- you have installed so-called "internet protection" software on the Mac
- you have installed "internet monitoring" software on the Mac (like "Little Snitch")
- you have installed VPN client software on the Mac - and many of these applications install their own firewall
All this stuff needs to go, since it will cause all sorts of trouble with communication between a Base Station or Airport Express, and a Mac.
I'd also be very worried about what this "Cocktail" utility is really doing to your system.

Link Express and Extreme?

I live in a two-floor apartment. My Ethernet connection plugs into an Airport Express on the first floor. The signal upstairs is a little weak.
If I buy an Airport Extreme and put it upstairs, will it amplify the signal from the Express and give me a better connection upstairs?
Also: If that works, and I can link the Express and Extreme, can I plug a USB HD into the Extreme that's sitting upstairs? Or does the Ethernet have to be fed directly into the Extreme?

XYU77, Welcome to the discussion area!
You can configure the AirPort Express (AX) and AirPort Extreme base station (AEBS) to wirelessly connect using WDS. The AEBS will then extend the wireless signal from the AX. All of the AEBS's service would be available... this includes a connected USB hard drive.

What is the difference between express and extreme?

I am wondering what is the difference between express and extreme and will there be any effect in performance if I am just using it at home?

I am just looking for router that gives me reliable highspeed wi-fi for personal use within my home.
Wireless performance is roughly equal between the two devices, with a slight edge to the Extreme since it uses a bit better antenna package.
If I connect the the hard drive to the extreme, does that mean I can back up all my data wirelessly through the port into my external hard drive?
Yes, if you backup manually, or use an application like Carbon Copy Cloner or SuperDuper.
No, if you were planning to use Apple's Time Machine application since Time Machine backups to a hard drive at the USB port of the AirPort Extreme are not officially supported by Apple.

Differences between AirPort Express and Extreme?

What are they differences between AirPort Express and Extreme?

You can find all the differences between the AirPort Express and Extreme in this website > http://www.apple.com/compare-wifi-models/

What are the main differences between airport express and extreme?

what are the main differences between the express and extreme base stations.

In addition to Bob Timmons' link the main differences are as follows:
Extreme has a slightly more powerful antenna (might not be true but from experience it seems to be)
Extreme has USB HDD sharing
Express has AirPlay
Extreme has 3 Gigabit ports (don't be confused by Apple's page. Apple states 4 including WAN, 3 without WAN)
Express is smaller
Express has 10/100 Ethernet whereas Extreme has Gigabit

Any software differences between new airport express and extreme?

I was wondering if there are any features or configuration differences between the two, such as configuring VPN passthrough.
The only difference I can see is using the USB for hard drive use.
Also, do you think the performance will be similar. I know the time capsule actually rated slower than the extreme even though they use similar hardware.

You can find all the differences between the AirPort Express and Extreme in this website > http://www.apple.com/compare-wifi-models/

TS1741 Remote isn't recognising my new AirPort Extreme but does pick up an old appleTV and ap express and extreme.anyone know why? It does pick it up from the Music app

Remote isn't recognising my new AirPort Extreme but does pick up an old appleTV and ap express and extreme.Anyone know why? It does pick it up the new AP express from the Music app and plays through a single speaker

Remote isn't recognising my new AirPort Extreme but does pick up an old appleTV and ap express and extreme.Anyone know why? It does pick it up the new AP express from the Music app and plays through a single speaker

Problems Extending latest Express and Extreme

I have the latest extreme and just bought the latest express to extend my network.
I have tried both manual and 'auto' methods to extend the network. The extreme is in my basement, the express is 2 rooms away in an area that gets 3 out of 4 possible bars reception according to my laptop. I want to wirelessly extend.
There are multiple issues:
1). The express flases orange
2). The extress vanishes once set up so that I cannot see it via the airport utility
3). It obviously isn't working as 1 foot from the express the signal does not go to full bars
Any help appreciated - can't see it mentioned elsewhere where the express vanishes under the airport uti

OK, thanks for checking that for me. We'll need to check your settings on both the AirPort Extreme and the Express.
Open AirPort Utility, select the AirPort Extreme, and click Manual Setup
Click the Wireless tab located just below the row of icons
Make sure that there is a check mark next to "Allow this network to be extended" on this page
Update to save any changes
Open AirPort Utility, select the AirPort Express, and click Manual Setup
Click the Wireless tab...settings should look like this:
Wireless Mode = Extend a wireless network
Wireless Network Name = Same name as the AirPort Extreme network
Check mark next to Allow Wireless Clients
Wireless Security = Same setting as the AirPort Extreme
Wireless Password = Same password as the AirPort Extreme
Confirm Password
Update to save any changes and allow 40-45 seconds for the Express to restart
Then power down the entire network....all devices...order is not important
Wait a moment, then start the modem first and let it run a moment or two by itself
Start the AirPort Extreme the same way
Start the Express the same way
Start each other device one at a time about a minute apart
Check for proper operation
A good location for the Express is a point that is about half the distance from the AirPort Extreme to the general area that needs more wireless coverage. Depending on obstructions, you may need to vary this a bit.
Post back on your progress and I will give you a tip to know which device.....AirPort Extreme or AirPort Express....your Mac is connecting to any given location.

Airport Express and Extreme drop out

Hi,
I have a Airport express that is wired to my router. This is downstairs.
Upstairs i have a Airport Extreme which is wirelessly connected to the airport downstairs.
The Express is set to create a new wireless and the extreme is set to extend.
For some reason or another when im upstairs, which means i'll probably be connected to the extreme, i sometimes find that i cannon connect to the internet. When i go into Airport Utility it can only see the Extreme that's up stairs.
If i go downstairs it then allows me to connect to the internet.
Then go back upstairs and cannot get back on the net.
So i have to disconnect the power to the express and then the connection between the two airports is established.
Both are running the latest firmware, 7.6.
Can anyone help?
Thanks

I have Sunrocket and the same situation. However the last week has had about 90% use... no problems.
I was having people completely unable to understand me. All of a sudden the stuff started working but it still isn't perfect. I can only guess that the AEBS is not liking the setup or otherwise being interfered with. I DO have 2.4GHz phones but the brand was checked out as working fine with AEBS.
My setup Comcast Cable Internet>AEBS>Sunrocket's Gizmo.
I'd love to hear form other Mac/AEBS users and Sunrocket.

Interference with my Express and Extreme?

I have an Airport Extreme purchased several years ago to connect two iMacs. We have updated each computer, one is a newer iMac and the other is a MacBookPro (06). We have had trouble getting a signal to reach both computers since we first bought the Extreme. I added an Express and it seemed to solve the problem.
The Extreme is located next to the desktop computer. My laptop (which is never further than 40 feet), randomly gets dropped offline. I have to go through choosing airport, my network, etc, each time I'm dropped and each time I boot up. I never had to do this before. The only change I made recently was password protecting my network. I have done software updates since the problem started and also have run firmware and software diagnostic tests which were fine.
I've been to the Genius Bar three times, I've spoken with Apple Tech support for over 3 hours total on this issue. The Extreme tested fine in the Apple Store, I purchased a new Express and the problem is worse. When I get connected it will sometimes work 20 minutes, an hour, or 5 minutes. When this happens I have to sit right next to the Extreme to pick up a signal.
We have single wall construction, no cordless phones and I can't think of any other interference. Sorry this is so long but I'm desperate! Thank you

{quote:title=alohajam-Hawaii wrote:The only change I made recently was password protecting my network.}{quote}
Hmmm. That can make a difference, but I would think that should be exhibited as a performance hit as opposed to a reliability problem. Early AirPort Extremes took a hit with WEP (according to http://www.smallnetbuilder.com/content/view/30664/228/). After looking at iStumbler, there's an old (2004) but good article at http://www.smallnetbuilder.com/content/view/24311/98/ covering a/b/g nets; for instance, make sure your SSID is unique. Also, if running 802.11n, take a look at this article at http://www.smallnetbuilder.com/content/view/30664/228/ (esp. Fixes #4 and #5).
I found running 802.11n to be futile around here (well, it is Silicon Valley). [iStumbler] will give you a clue about things in your area, but I found that the local WiFi environment changed day-to-day as new nets came online, or folks changed the bands they're using and/or switched to using wide channels (channel bonding). I could never stabilize things for more than a day or two here, so ended up buying a new Extreme and running Radio Mode = 5 GHz only - the only one in the area (at the time). That helped lots.

Can I expand an expanded network with airport express and extreme?

Hi, I would like to know, what happen if I have 1 Airport Extreme and 2 Airport Express.
First, my airport extreme is creating my wifi network in my house, and i have an airport express, expanding my wifi signal.
What happen if I want to add another airport express, like expanding the expanded network, something like this:
Internet
      |
     |
     |(Ethernet Cable)
     |
     |
Airport Extreme
     |
     |
     |(Wifi)
     |
     |
Airport Express 1
     |
     |
     |(Wifi)
     |
     |
Airport Express 2
So, can I expand my signal, just adding more airport express?

So, can I expand my signal, just adding more airport express?
No, since Apple will only allow you to "extend" the signal one time.
It is possible to have multiple extenders, but each extender must connect directly to the "main" base station....not to another device that is already extending the network.
Apple's extend setup works like the hub and spokes of a wheel. Your main base station is the "hub". Each extender resides at the end of a separate "spoke", and as such it communicates directly to the "hub"......not to another extender at the end of another spoke.

D-LINK router interferes with Airport Express and Extreme

Thanks everyone! I found out that the problem was and is that my DLINK router network is constantly interfering. I unplugged the DLINK and now I can see the Ariport Extreme AND Express in the Airport utility - for the first time actually. Would anyone have an idea how to disable the DLINK network? I tried in the network preferences using the "-" to delete it from the list but it keeps coming back.
Thanks

yogisan, Welcome to the discussion area!
Configure the D-Link to use a different channel or see if the D-Link has a configuration option to disable the wireless interface.

3 powerline adaptors with airport express and extreme

Hi all,
I am currently using two airport express and 2 TP-LINK powerline adaptors to create a "roaming" network, however i would like to add another powerline adaptor and an airport extreme to my network.
Modem -> Airport Extreme in the living room with an ethernet cable plugged into the powerline
1st Airport Express plugged into the 2nd powerline adaptor
3rd Airport Express plugged into the 3rd powerline adaptor
so my question is will the above setup work? or do i need to connect another powerline adaptor into the main Airport Extreme making the whole network use a total of 4 powerline adaptors? however if only a total of 3 powerline adaptors are required, would the network be confused and render the whole network useless?

To set up the 802.11n AirPort Extreme Base Station (AEBSn) as a bridge, either connect to the AEBSn's wireless network or temporarily connect your computer directly (using an Ethernet cable) to one of the LAN port of the AEBSn, and then, using the AirPort Utility, make these settings:
AirPort Utility > Select the AEBSn > Manual Setup > Internet > Internet Connection tab
Connection Sharing: Off (Bridge Mode)
Click Update to apply the new settings
AirPort Express Base Station (AX) - iTunes Setup
Either connect to the AX's wireless network or connect directly, using an Ethernet cable, to the Ethernet port of the AX, and then using the AirPort Utility in "Manual Setup" mode, make the following changes:
AirPort Utility > Select the AX > Manual Setup > AirPort > Wireless
Wireless Mode: Join a wireless network
Network Name: <existing AEBSn's wireless network>
Wireless Security: <select the encryption type of the existing wireless network>
Wireless Password: <enter the existing wireless network password>
Verify Password: <re-enter the existing wireless network password>
AirPort Utility > Select the AX > Manual Setup >Music
Enable AirPlay (checked)
iTunes Speaker Name: <enter desired speaker name>
iTunes Speaker Password: (optional)
Verify Password: (optional)
Click Update to write the new settings to the AX

Internet problem Express AND Extreme

Similar Messages

Maybe you are looking for