Internet sharing from mountain lion to tiger over firewire
Hi, I have just purchased an imac g4 from ebay and am having trouble getting it to connect to the internet.
My internet connection comes from teathering my iphone over wifi to my MBP. I have been trying to share this connection from my macbook to my imac over firewire but haven't had any luck.
I've tried connecting direct to my phone over wifi but I don't get an ip address, the same happens when I share the connection from my laptops wi-fi.
I have connected to a hotspot with the imac so i know that the wi-fi works and i can get a connection over firewire that says "You are connected to the internet via built in firewire" but when i try and load a webpage i cannot load anything.
When connected via firewire my macbook shows up in the network tab of the finder, my shared itunes library shows up and my laptop comes up in the list of devices in my VNC but when i try to use these connections it always fails, i cannot even get a ping responce from my laptop.
Im not sure if it is a compatibility issue with M lion and tiger, an IP address issue or something els entirely.
All help would be greatly appriciated
Thanks in advanced
Jake
If you use your MacBook Pro as the "server" connected to the Internet. you can connect 27" 2011 iMac to your MacBook Pro via a FireWire 800 cable. (assuming your MBP has a FireWire output, I don't own one).By using Target Disk Mode (Hold down the "T" key until you see "spinning gears" on Restart or Start-up).
Your MBP will appear as a Hard Disk on your 27" display or your 27" iMac can be displayed as a Hard disc on your MBP display.
Switch the firewall off on both machines (if it was on) to see if it helps;
Try to connect using a different device to the shared connection (another computer, smartphone, iPad, etc.);
Use an open connection first (no password), before trying with WEP;
Reverse the roles of the two computers (i.e. try sharing the connection from the MBP to the iMac).
Also, more details might help (OS X version on the machines, whether you are trying to share a wired connection, installed software which might interact with the network connections, etc.)
Hope this helps in some way.
Similar Messages
-
Screen Sharing between Mountain Lion and Tiger not working
rMBP running 10.8.2 ML and a G3 iMac running 10.4.11 Tiger.
When I try and use Screen Sharing on the MBP to connect to the G3 it prompts for both a username and password. I enter a valid user and pw but it fails with
Authenication failed to "Ruby".
Please verify you have entered the correct name and password.
Third-party VNC clients, e.g. JollysFastVNC on my MBP and Remoter on my iPhone, can connect fine, but they only request a password.
Any ideas?I've been using Screen Share on my home network for a very long time. My most used computer, MacBook Pro (2011) was just upgraded to ML, my desktop still has Lion on it - and can't be upgraded because it is an early MacPro. I was having intermittant problems getting the MBPro to connect to the MPro screen, and resetting the PRAM was correcting it (but it could have been the rebooting process alone - I don't know). Now I can share the MPro disks on my network but not the screen. Now, to me, that's wierd. I've tried doing all kinds of setting checks, preference removal, etc. No luck. I can, however (as someone above mentioned) connect from my MPro (Lion) to my MBPro (ML) screen. I've checked my Intego VirusBarrier X6 settings, i.e. blocked addresses (in the past that has happened and blocked) and I've even entered my MBPro address into the approved address section. I've checked/rechecked the Sharing Preferences, turned them on/off, etc. All to no avail.
Is this a Mountain Lion / Lion issue, a Mountain Lion issue, or something somewhere corrupt? I used to have Remote Desktop on the MPro, but for my needs Screen Share & Disk Share suit my needs on my home network. I have LogMeInIgnition, which when the last time I tried to connect to the MBPro it showed it offline - and it isn't. I feel there's something in ML blocking things.
I'm open to suggestions, and a fix if needed. This is frustrating. Not that I can't use the exercise to walk to the room where the MPro is - not the point.
Tom -
In case of lost internet connection during mountain lion download from app store, do i have to start over?
How do I speed this up. I have a fast internet connection but this is obviously not right.
The speed of the downlaod is dependant on the speed of your Internet connection. "I have a fast Internet connection...," doesn't actually mean anything unless you provide some numbers.
I have a cable Internet connection with 32 Mbps download speeds, but if you have DSL, you would probably be limited to 1.5 Mbps. Some would call both of these connections "fast," but obviously one is faster than the other.
What is the speed of your Internet connection?? Don't say, "fast."
Test it here: http://www.dslreports.com/speedtest?flash=1 -
Will Mountain Lion fix the major Internet Sharing bug in Lion?
Does anyone know if Apple have indicated that they will be issuing a fix to the Internet Sharing bug in Lion (i.e. Internet Sharing does not work) in the new Mountain Lion?
Hmmm. Pete, suggest cease dissing people's problem with VNC in Mt Lion as "doesn't exist here" syndrome. Maybe for you, it's working just fine....for some of us...NOT.
Following several threads on issues with VNC and Lion and the vague hope that Mt Lion would fix the problem, I also upgraded to Mt Lion. Worse.
Prior to Lion, VNC worked every time with any Mac I tried, inside or outside the local network. With Lion, VNC worked correctly until around 10.7.4, then with intermittent connections (requiring restarts on the target Mac in order to connect a second time).
Now, with Mt Lion (target Mac is still on Lion and restarted), I cannot connect externally to the Lion Mac even with it being restarted (and Screen Sharing and Remote Management turned off/on as one thread suggested).
As another thread suggested, I had deleted the iCloud System Pref on both Macs while on Lion (with no effect to VNC).
While I'm sure there's a solution out there, I have yet to find it.
Thanks for any suggestions, but will someone at Apple please address this issue? -
Internet Sharing from Macbook Pro to iPad???
Trying to get my wife's iPad to connect to the internet in a hotel that has wired high speed internet but no wifi.
My MacBook Pro connects just fine. So I turned on Internet Sharing for both Bluetooth and wifi (with WEP password for wifi).
The iPad connects to the Mac by wifi but says it has no internet connection.
With Bluetooth, it pairs OK. The Mac sets it up as serial port sharing (no other choice offered, but within that there is a choice of modem or RS232 protocol). But when I try to connect it connects momentarily then disconnects right away.
Any suggestions on how to let the iPad get at the internet in this situation?I am still not succeeding.
I just upgraded to a new Macbook Pro with Mountain Lion. Testing at home, where there are no issues around hotel ISP limitations and I feel pretty safe originating an open wifi network for a few minutes.
Set up Internet Sharing from Ethernet to Wifi. Used the Create Network option for wifi in the menu bar to set up an open unprotected wifi network whose name is the name of my Mac. I can choose any wifi channel from 1 to 11; it makes no difference.
I can see that network from my wife's iPad, and can connect to it no problem. But as in all similar tests since Snow Leopard came out, Safari in the iPad can't open any web sites; it says it is not connected to the internet. I can also connect to the MBP wifi from my iPhone, but if I select it, the 3G symbol still shows at the top of the screen because the phone cannot find an internet connection over that wifi.
Clearly some other people are managing to do what I cannot. Quite possibly some piece of third party software on my Mac is interfering. Little Snitch, for example, though it is currently turned off. -
Dear Apple Support Community.
As mentioned by a number of users reporting the same problem, my 2009 iMac CPU3.06 GHz Intel Core 2 Duo, 8GB RAM, has become extremely slow and repeatedly "out of Memory" since it was migrated from Mountain Lion to Mavericks (OS 10.9 then OS 10.9.1).
I have already run CleanMyMac, deleted 5GB of useless stuffs, which did not translate into any improvement. Following the advices collected in other Apple Support Community threads, I have applied EtreCheck the outcome of which is provided below.
For information, I have also upgraded my 2011 MacBook CPU2.3 GHz Core i7, 8GB which became only a bit slower than before, sometimes freezing which it almost never did before. However, I am used to the fact that Mac get usually slower and more prompt fo freeze after upgrading to a more recent OS.
Both my 2009 iMac and my 2011 MacBook have F-Secure installed. So the problem with the 2009 IMac is unlikly to be due to the presence of F-Secure. Interestingly, the few abnormalities found by Etrecheck were exacly identical before I ran CleanMyMac. There are two more findings (mentioned below) since I ran CleanMyMac on the 2009 iMac, which again didn't improve the problem.
So please find below the details of the EtreCheck experience and some additional measurements made with iStat while running EtreCheck:
Hardware Information:
iMac (24-inch, Early 2009)
iMac - model: iMac9,1
1 3.06 GHz Intel Core 2 Duo CPU: 2 cores
8 GB RAM
Video Information:
ATI Radeon HD 4850 - VRAM: 512 MB
Audio Plug-ins:
BluetoothAudioPlugIn: Version: 1.0 - SDK 10.9
AirPlay: Version: 1.9 - SDK 10.9
AppleAVBAudio: Version: 2.0.0 - SDK 10.9
iSightAudio: Version: 7.7.3 - SDK 10.9
System Software:
OS X 10.9.1 (13B42) - Uptime: 0 days 2:40:57
Disk Information:
WDC WD1001FALS-40K1B0 disk0 : (1 TB)
EFI (disk0s1) <not mounted>: 209.7 MB
XooS5 HD (disk0s2) /: 999.35 GB (189.85 GB free)
Recovery HD (disk0s3) <not mounted>: 650 MB
OPTIARC DVD RW AD-5670S
USB Information:
Apple Inc. Built-in iSight
Canon CanoScan
Apple Computer, Inc. IR Receiver
Apple Inc. BRCM2046 Hub
Apple Inc. Bluetooth USB Host Controller
FireWire Information:
WD My Passport 071D 800mbit - 800mbit max
EFI (disk1s1) <not mounted>: 209.7 MB
disk1s2 (disk1s2) <not mounted>: 2 TB
Boot OS X (disk1s3) <not mounted>: 134.2 MB
Thunderbolt Information:
Kernel Extensions:
com.f-secure.kext.fsauth (1.0.0d1)
Problem System Launch Daemons:
[failed] com.apple.wdhelper.plist [REMARK: this abnormality appeared only after running CleanMyMac. It does not appear on my 2011 MacBook]
Problem System Launch Agents:
Launch Daemons:
[loaded] com.adobe.fpsaud.plist
[invalid] com.bjango.istatlocaldaemon.plist [REMARK: this abnormality pre-existed to running CleanMyMac. It appears also on my 2011 MacBook]
[loaded] com.f-secure.fsavd.dbhelper.plist
[loaded] com.f-secure.fsavd.plist
[loaded] com.f-secure.fsmac.firewall.plist
[loaded] com.f-secure.fsmac.fsupdated_guts2.plist
[loaded] com.f-secure.fsmac.licensetool.plist
[loaded] com.macpaw.CleanMyMac2.Agent.plist
Launch Agents:
[loaded] com.babylon.activation.plist
[loaded] com.bjango.istatlocal.plist
[loaded] com.f-secure.relauncher.plist
[loaded] com.f-secure.trasher.plist
User Launch Agents:
[loaded] com.adobe.ARM.[...].plist
[loaded] com.google.keystone.agent.plist
[loaded] com.macpaw.CleanMyMac2Helper.diskSpaceWatcher.plist
[loaded] com.macpaw.CleanMyMac2Helper.scheduledScan.plist
[loaded] com.macpaw.CleanMyMac2Helper.trashWatcher.plist
User Login Items:
iTunesHelper
Dropbox
F-Secure Anti-Virus for MAC
3rd Party Preference Panes:
Flash Player
Internet Plug-ins::
FlashPlayer-10.6: Version: 11.9.900.170 - SDK 10.6
Default Browser: Version: 537 - SDK 10.9
AdobePDFViewerNPAPI: Version: 11.0.04 - SDK 10.6
AdobePDFViewer: Version: 11.0.04 - SDK 10.6
DivXBrowserPlugin: Version: 2.1
Flash Player: Version: 11.9.900.170 - SDK 10.6
OfficeLiveBrowserPlugin: Version: 12.2.8
Google Earth Web Plug-in: Version: 6.1
QuickTime Plugin: Version: 7.7.3
iPhotoPhotocast: Version: 7.0
User Internet Plug-ins::
Picasa: Version: 1.0
Bad Fonts:
None
Old applications:
None
Time Machine:
Skip System Files: NO
Mobile backups: OFF
Auto backup: YES
Volumes being backed up:
XooS5 HD: Disk size: 930.71 GB Disk used: 753.90 GB
Destinations:
XooS5 TM [Local] (Last used)
Total size: 2
Total number of backups: 32
Oldest backup: 2013-09-15 01:11:39 +0000
Last backup: 2013-12-07 12:48:45 +0000
Size of backup disk: Too small. Backup size 2 < (Disk used 753.90 GB X 3)
Time Machine details may not be accurate. All volumes being backed up may not be listed.
REMARK: The above finding is unlikely to be accurate. In fact, my Time Machine is supported by a 2TB WD My Passport Studio external HD connected with a Firewire 800. As mentionned, only 754GB of the 2000GB are used.
Top Processes by CPU:
5% backupd
5% Mail
5% WindowServer
3% Finder
3% Dropbox
Top Processes by Memory:
1.60 GB mds_stores REMARK: this item was marked in red in the outcome of EtreCheck, so I assume there is something wrong there
82 MB Finder
74 MB Mail
49 MB softwareupdated
49 MB Dropbox
Virtual Memory Statistics:
97 MB Free RAM
1.21 GB Active RAM
1.19 GB Inactive RAM
1.21 GB Wired RAM
1.83 GB Page-ins
36 MB Page-outs
Please find now some additional measurements collected with iStat while running EtreCheck:
Practically:
The iMac can work slowly with only one software e.g. either Mail or Safari or Firefox, but still the below "out of Memory" message occurs about every 3 minutes.
Aperture has becomre to slow to be useable
If trying to write a mail (with Mail) while Safari or Firefox is open, then the "out of Memory" message occurs about every 20 seconds so I need to check on "Resume" several times per minute.
Conclusions
From the above, unless anyone in the Apple Support Community proves to be able to identify a specific problem leading to a way to find a cure, I tend to conclude that Mavericks is not suitable for computers operating with a Core 2 Duo CPU even with a 8GB of RAM.
Unless I missed something, I did not see any warning from Apple Computer Inc. informing their customers they should refrain from upgrading Core 2 Duo Computers.
The only solution I see so far is to downgrade from Mavericks to Mountain Lion. And the Apple Support Community would confirm that it is the only solution, I would appreciate to get your guidance on how to proceed.
Intended action plan
Migrate the above 2009 iMac to a 2014 Mac Mini Server operating on Mavericks to ensure that no data may be lost while downgrading to Montain Lion.
Provided the above downgrading operation is successful, assign this 2009 iMac to partial retirement e.g. Mail, Skype, iTunes and DVD player.
In advance, I would like to thank the Apple Community for helping me either i) finding a cure to the problem, ii) or confirming that Mavericks cannot operate properly on Core 2 Duo computers, iii) and in such a case, guiding me on how to downgrade to Mountain Lion.
Yours sincerely
Core... what anti-virus would you recommend using?
Use what is already included with OS X. It already includes everything it needs to protect itself from viruses and malware. Keep it that way with software updates from Apple.
A much better question is "how should I protect my Mac":
Never install any product that claims to "speed up", "clean up", "optimize", or "accelerate" your Mac. Without exception, they will do the opposite.
Never install pirated or "cracked" software, software obtained from dubious websites, or other questionable sources. Illegally obtained software is almost certain to contain malware.
Don’t supply your password in response to a popup window requesting it, unless you know what it is and the reason your credentials are required.
Don’t open email attachments from email addresses that you do not recognize, or click links contained in an email:
Most of these are scams that direct you to fraudulent sites that attempt to convince you to disclose personal information.
Such "phishing" attempts are the 21st century equivalent of a social exploit that has existed since the dawn of civilization. Don’t fall for it.
Apple will never ask you to reveal personal information in an email. If you receive an unexpected email from Apple saying your account will be closed unless you take immediate action, just ignore it. If your iTunes or App Store account becomes disabled for valid reasons, you will know when you try to buy something or log in to this support site, and are unable to.
Don’t install browser extensions unless you understand their purpose. Go to the Safari menu > Preferences > Extensions. If you see any extensions that you do not recognize or understand, simply click the Uninstall button and they will be gone.
Don’t install Java unless you are certain that you need it:
Java, a non-Apple product, is a potential vector for malware. If you are required to use Java, be mindful of that possibility.
Disable Java in Safari > Preferences > Security.
Despite its name JavaScript is unrelated to Java. No malware can infect your Mac through JavaScript. It’s OK to leave it enabled.
Block browser popups: Safari menu > Preferences > Security > and check "Block popup windows":
Popup windows are useful and required for some websites, but popups have devolved to become a common means to deliver targeted advertising that you probably do not want.
Popups themselves cannot infect your Mac, but many contain resource-hungry code that will slow down Internet browsing.
If you ever see a popup indicating it detected registry errors, that your Mac is infected with some ick, or that you won some prize, it is 100% fraudulent. Ignore it.
Ignore hyperventilating popular media outlets that thrive by promoting fear and discord with entertainment products arrogantly presented as "news". Learn what real threats actually exist and how to arm yourself against them:
The most serious threat to your data security is phishing. To date, most of these attempts have been pathetic and are easily recognized, but that is likely to change in the future as criminals become more clever.
OS X viruses do not exist, but intentionally malicious or poorly written code, created by either nefarious or inept individuals, is nothing new.
Never install something without first knowing what it is, what it does, how it works, and how to get rid of it when you don’t want it any more.
If you elect to use "anti-virus" software, familiarize yourself with its limitations and potential to cause adverse effects, and apply the principle immediately preceding this one.
Most such utilities will only slow down and destabilize your Mac while they look for viruses that do not exist, conveying no benefit whatsoever - other than to make you "feel good" about security, when you should actually be exercising sound judgment, derived from accurate knowledge, based on verifiable facts.
Do install updates from Apple as they become available. No one knows more about Macs and how to protect them than the company that builds them.
Summary: Use common sense and caution when you use your Mac, just like you would in any social context. There is no product, utility, or magic talisman that can protect you from all the evils of mankind. -
Mavericks upgrade from Mountain Lion deletes all user accounts
This is a lesson for upgrading too early (and too eagerly).
Today I tried the Mavericks upgrade from Mountain Lion on my 2007 Macbook Pro, after going through all the pre-installation/pre-upgrade checklists.
I don't think I have gone from a very high to a down low in such a short space of time. I really wanted to move on from Mountain Lion and when the installer finished the upgrade to Mavericks and re-started my MBP, I was super excited. When the restart completed and I was presented with the login prompt, I tried entering my user name and password. First time, it shaked on the password... OK, you'd think that is a typo. Re-entering the password... same thing.
You can imagine what ensued. After entering my password v-e-r-y slowly many times, I started realising that something went very VERY wrong.
Just for information, I used two different user accounts on my MBP under Mountain Lion. The one account had administrative priviledges and was only used for installing applications and a few other administrative tasks. Then I have a second personal account, which does not have administrative priviledges and is the account I use daily for Mail, Safari, iTunes, programming etc.
None of those accounts worked under Mountain Lion. Basically, there is no way in.
I then proceeded to boot with the startup option Cmd + S (command-line access). Once that was completed, I was in as root and checked the /etc/passwd. None of the user accounts were there. I was only able to find two user accounts: root and nobody; and a long list of user account that started with an underscore (I think these are some sort of esoteric user accounts). So, it appears that the Mavericks upgrade did not accurately bring over the user account information from my Mountail Lion installation.
Then, I went into the /Users directory and there I could see the home directories for all the users as they were defined under Mountain Lion. The contents were intact too.
It seems to me that the Mavericks upgrade from my Mountain Lion forgot to bring over the user accounts but it did preserve the contents of all the users' home directories.
Unless anyone can spot some sort of user error here (please let me know), I am heading back to Mountain Lion pretty swiftly. Otherwise, I suspect there is a bug in the Mavericks installer.
Any assistance is appreciated.The reason this occurred is a mystery and has not been commonly reported. Consider the following. It may or may not help. You should probably print these instructions before proceeding.
Boot Single User mode again and do the following:
(You can skip the first step. It will check your boot volume for errors and correct what it can. If there were errors the installer should not have proceeded, but the possibility exists that directory corruption may have occurred during installation. That seems unlikely to me but could explain what went wrong.)
In Single User Mode:
At the :/ root# prompt, type fsck -fy and press Return or Enter. It will take a few moments to complete. If you are concerned that nothing is happening just press the Return key until you see the :/ root# prompt again.
Once the disk check is complete and the prompt returns, type mount -uw / and press Return / Enter.
Type launchctl load /System/Library/LaunchDaemons/com.apple.opendirectoryd.plist and press Enter. If you get an error message you may ignore it.
Type ls /Users and press Enter. All of the usernames on the computer will be listed, which is helpful if you don’t know or remember what these are.
Type dscl . passwd /Users/username password while replacing username with one of the users displayed in the previous step and replacing password with the new password of your choice. Press Enter. You will likely get an error message about a file or directory not being found. You may ignore this.
Type reboot and press Enter. -
How do I turn off internet recovery in Mountain Lion?
I need to turn off internet recovery in Mountain Lion. The reason is if you use internet recovery you can access safari and although parental controls are on, internet is unmonitored. I want to ensure my MBP is secure from the darker parts of the internet and thus I don't want there to be any unmonitored internet access.
Is there a way to turn off internet recovery or is it hardwired into Mounatin Lion?
SebOpen firmware password may be the way to do it. Mind you, a clever enough person can bypass that, but it takes more effort than it usually is worth. Put a hidden camera in the room if you are worried something will happen, and backup the data only when you are present. And if you forget the open firmware password, you may have locked yourself out for good anyway.
-
Exporting OS X Mail from Mountain Lion to Snow Leopard
After upgrading to Mountain Lion, I partitioned my iMac HD to have two partitions: Macintosh HD has Mountain Lion; I reinstalled Snow Leopard on Macintosh HD 2. Best part: you can access your user-created files from EITHER disk partition. But not so OS X Mail. I wanted to revert to Snow Leopard, since I don't like the iOS-like Mountain Lion (swipe THIS!), but Mail was a problem since all my Snow Leopard Mail was successfully migrated over to Mountain Lion during upgrade. But I think I found a way to Export Mail from ML to (a clean install of) SL.
Try this:
1. Open Mail in ML. For each folder you wish to have back in SL, Export it to your ML Desktop as an .mbox file. Depending on the folder size, this can take from a few seconds to several minutes. You'll see an .mbox icon for the particular folder on your Desktop. If the word "partial" appears between the folder name and the .mbox suffix, wait a few moments for the Export to complete, at which time the word "partial" will disappear. E.g., for a folder named "Mary", if it's a huge one, the icon will first appear as "Mary.partial.mbox"; when the Export is done, you'll see "Mary.mbox".
2. When you've Exported all your desired folders as above, you can exit ML and re-start your Mac in SL. Open Mail in Snow Leopard, and once again, for each file you just Exported in ML to the Desktop there, select "Import Data From Apple Mail" and choose the folder from the Desktop in ML to which your mboxes were Exported. When the Import starts, you can see via a progress bar how far along it is. When done, you'll see a new folder in your SL Mail called "Import"; click on it to reveal the folder you just Imported!
3. Then drag the folder you just Imported out of the Import folder to "On My Mac" in SL Mail; you can then delete the Import folder.
4. Repeat until all your folders are where you want them (in SL).
5. When you have time, go back into ML and clear all those .mbox files from your Desktop.
There MAY be an easier way, but this is what worked for me.The iOS view vs classic view in Mail is not the problem; I've already configured for classic view.
Mountain Lion itself is.
My short list (to date) of crappy Mountain Lion behavior; items marked with a double asterisk (**)represent the worst of Mountain Lion for me.
** No up/down arrows in scroll bar slider;
Expose` not as easy to navigate as in Snow Leopard;
Mail does not request passwords for either receive or send;
No "Save Draft" icon in Mail compose window (workaround: use command-s);
"Save As" selection missing in most app menus;
No separate Search window in Safari (workaround: use Firefox or Opera);
** Can't export Mail from Mountain Lion into Snow Leopard if downgrading (I compiled this list before I stumbled on the method in this thread, but I'd prefer to effect this with Unix symbolic links);
iWork 09 seems to have "circled the wagons" re compatibility with MS Office or LibreOffice (workaround: just use Libreoffice); -
just update my iMac from Mountain Lion to Mavericks and the application are slow to open. The same happens to opening webpages . Please help
Resetting your Mac's PRAM and NVRAM
Intel-based Macs: Resetting the System Management Controller (SMC)
Restart the computer in Safe Mode, then restart again, normally. If this doesn't help, then:
Reinstalling Mavericks, Lion/Mountain Lion Without Erasing the Drive
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall Lion/Mountain Lion, Mavericks: Select Reinstall Lion/Mountain Lion, Mavericks and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless. -
I recently downgraded from Mountain Lion back to Snow Leopard and I forgot to export my bookmarks.
Unfortunately downgrading from Mountain Lion back to Snow Leopard means I need to wipe the hard drive and install everything from scratch. That takes hours, and I've already done the bulk of the work, twice actually since I forgot to back up my photos in Iphoto and had to start over from my Time Machine backup of Mountain Lion.
Anyhow, I am curious as to whether or not there is a way to retrieve my bookmarks from the Time Machine backup and get them onto my downgraded OS, or will I have to start all over again, restore my system to Mountain Lion and go through the hours it takes to get back to Snow Leopard.You're missing the point. If you didn't make the /username/Library/ folder visible, then it's hidden on the TM backup. Getting to ii is beyond my ken. However, Pondini's TM FAQs might have info on that madness.
-
Boot camp lost after upgrading to Yosemite from mountain lion
I lost my windows7 boot camp after I upgrade to Yosemite from mountain lion. When I press ALT when rebooting there is no more alternative to boot for window anymore. I did read some thread about this but my case is different since when I tried to type 3 steps(diskutil.......etc) as LonerT user answers it did not work. The attached files here are what I faced with. Please help. I have a lot of important files in windows
If you look at the GAP between GPT3 and GPT4 it is start/size of 782929176/37595880 but the NTFS header starts at 782929920 according to your Testdisk output shown here.
MS Data 782929920 976773112 193843193
The difference is 782929920 - 782929176 = 744 bytes. You will need to delete the current GPT4 and recreate a new GPT4. Please stop if you see any error messages and post here.
1. Delete the old entry and create a new entry at GPT#4.
sudo gdisk /dev/disk0
p
d
4
n
4
782929920
976773112
0700
p
w
y
Here is an example of the delete/new...
Command (? for help): d
Partition number (1-4): 4
Command (? for help): n
Partition number (4-128, default 4): 4
First sector (34-1954210086, default = 1454210080) or {+-}size{KMGTP}: 1454211072
Last sector (1454211072-1954210086, default = 1954210086) or {+-}size{KMGTP}: 1954209791
Current type is 'Apple HFS/HFS+'
Hex code or GUID (L to show codes, Enter = AF00): 0700
Changed type of partition to 'Microsoft basic data'
Command (? for help): p
Disk /dev/disk0: 1954210120 sectors, 931.8 GiB
Logical sector size: 512 bytes
Disk identifier (GUID): 6ED0C429-00D1-4759-B50E-04B6FB80D0E3
Partition table holds up to 128 entries
First usable sector is 34, last usable sector is 1954210086
Partitions will be aligned on 8-sector boundaries
Total free space is 1293 sectors (646.5 KiB)
Number Start (sector) End (sector) Size Code Name
1 40 409639 200.0 MiB EF00 EFI System Partition
2 409640 1452940543 692.6 GiB AF00 Customer
3 1452940544 1454210079 619.9 MiB AB00 Recovery HD
4 1454211072 1954209791 238.4 GiB 0700 Microsoft basic data
2. This is a tedious process and you want to check after the second 'p'rint command that it looks reasonable, before the 'w'rite and 'y'es to confirm.
3. You will need to reboot after the change, because the disk you are booted from is the one being modified. Reboot will rebuild disk0s4 using the start/end you entered.
4. Run the dd command - sudo dd if=/dev/rdisk0s4 count=1 2>/dev/null | hexdump -C and check that the first line contains "R.NTFS".
5. Once you have a working GPT#4, a new hybrid MBR needs to be created which will overwrite what you see in your Fdisk output. This is also done using GPT Fdisk (Gdisk). Your numbers will look different than what are in the following example. In most cases, you will use the default except entry 4, which should have a 'y' for bootable flag.
sudo gdisk /dev/disk0
GPT fdisk (gdisk) version 0.8.10
Warning: Devices opened with shared lock will not have their
partition table automatically reloaded!
Partition table scan:
MBR: hybrid
BSD: not present
APM: not present
GPT: present
Found valid GPT with hybrid MBR; using GPT.
Command (? for help): p
Disk /dev/disk0: 490234752 sectors, 233.8 GiB
Logical sector size: 512 bytes
Disk identifier (GUID): 59BDFEEB-1EB4-4529-94FE-3CBC2C3CD513
Partition table holds up to 128 entries
First usable sector is 34, last usable sector is 490234718
Partitions will be aligned on 8-sector boundaries
Total free space is 2604 sectors (1.3 MiB)
Number Start (sector) End (sector) Size Code Name
1 40 409639 200.0 MiB EF00 EF
2 409640 401060383 191.0 GiB AF05 Macintosh HD
3 401060384 402329919 619.9 MiB AB00 Re
4 402331648 490233848 41.9 GiB 0700 Microsoft basic data
Command (? for help): r
Recovery/transformation command (? for help): h
WARNING! Hybrid MBRs are flaky and dangerous! If you decide not to use one,
just hit the Enter key at the below prompt and your MBR partition table will
be untouched.
Type from one to three GPT partition numbers, separated by spaces, to be
added to the hybrid MBR, in sequence: 2 3 4
Place EFI GPT (0xEE) partition first in MBR (good for GRUB)? (Y/N): y
Creating entry for GPT partition #2 (MBR partition #2)
Enter an MBR hex code (default AF): AF
Set the bootable flag? (Y/N): n
Creating entry for GPT partition #3 (MBR partition #3)
Enter an MBR hex code (default AB): AB
Set the bootable flag? (Y/N): n
Creating entry for GPT partition #4 (MBR partition #4)
Enter an MBR hex code (default 07): 07
Set the bootable flag? (Y/N): y
Recovery/transformation command (? for help): w
Final checks complete. About to write GPT data. THIS WILL OVERWRITE EXISTING
PARTITIONS!!
Do you want to proceed? (Y/N): y
OK; writing new GUID partition table (GPT) to /dev/disk0.
Warning: Devices opened with shared lock will not have their
partition table automatically reloaded!
Warning: The kernel may continue to use old or deleted partitions.
You should reboot or remove the drive.
The operation has completed successfully.
6. a. Test 1 - Can you see your Bootcamp volume in Finder.
b. Test 2 - Can you files in the Bootcamp volume?
c. Test 3 - Can you see Bootcamp in your System Preferences -> Startup Disk.
d. Test 4 - If Test 1-3 are successful, select Bootcamp and click on Restart. You may need Windows startup repair, if you see a hanging underline cursor at the top left corner of your screen. In most cases, it is not required.
Here is an example...
Command (? for help): d
Partition number (1-4): 4
Command (? for help): n
Partition number (4-128, default 4): 4
First sector (34-1954210086, default = 1454210080) or {+-}size{KMGTP}: 1454211072
Last sector (1454211072-1954210086, default = 1954210086) or {+-}size{KMGTP}: 1954209791
Current type is 'Apple HFS/HFS+'
Hex code or GUID (L to show codes, Enter = AF00): 0700
Changed type of partition to 'Microsoft basic data'
Command (? for help): p
Disk /dev/disk0: 1954210120 sectors, 931.8 GiB
Logical sector size: 512 bytes
Disk identifier (GUID): 6ED0C429-00D1-4759-B50E-04B6FB80D0E3
Partition table holds up to 128 entries
First usable sector is 34, last usable sector is 1954210086
Partitions will be aligned on 8-sector boundaries
Total free space is 1293 sectors (646.5 KiB)
Number Start (sector) End (sector) Size Code Name
1 40 409639 200.0 MiB EF00 EFI System Partition
2 409640 1452940543 692.6 GiB AF00 Customer
3 1452940544 1454210079 619.9 MiB AB00 Recovery HD
4 1454211072 1954209791 238.4 GiB 0700 Microsoft basic data -
I am connecting to the internet using the Internet Sharing from my iMac ...
The trouble is the messages in the Messages app are not sent when I am connected through my iMac ... When I key in a message and hit send a progress bar appears fills up till 90% and just gets stuck there and after a while the red exclamation mark stating the message was not sent appears ... Now if I connect through my wi-fi router or thether through my phone it works fine ... I can send / recieve messages ...
Similar points to note - Today when I tried to make an App Purchase - The security info screen ( new additon - http://isource.com/2012/04/11/iphone-app-store-security-info-alert/ ) popped up but I got a blank screen for the securtiy questions screen ... It was not loading the screen ... Some games the game center invite does not work through my Internet sharing (tried in MetalStorm) ... but works fine thorough wi-fi or thether ...
What could be the problem with my iMac s sharing? Any suggestions would be really useful /// Thanx in advance
I am running Lion ... and I have updated to the latest Airport software ...
Only thing I tried was changing the DNS ... but that s not related right ?Powerline adapters use your home powerlines (mains a/c) to connect your devices via ethernet to your modem, they're easy to set up and the they TOTALLY fixed my ATV problem, the problem seems to be with the wireless. I've been trawling through apple discussions, and did found a workaround to my problem https://discussions.apple.com/thread/4222883?start=0&tstart=0
but its just a workaround :/ -
After upgrading macbook pro from mountain lion to mavericks computer performance slowdown
after upgrading macbook pro from mountain lion to mavericks computer performance slowdown
Fixing a Mavericks Installation Problem
How to manage a failed OS X Mavericks installation | MacFixIt - CNET Reviews.
Try these in order:
1. a. Resetting your Mac's PRAM and NVRAM
b. Intel-based Macs: Resetting the System Management Controller (SMC)
2. Restart the computer in Safe Mode, then restart again, normally. If this doesn't help, then:
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the
COMMAND and R keys until the Utilities menu screen appears. Alternatively, restart the computer and
after the chime press and hold down the OPTION key until the boot manager screen appears.
Select the Recovery HD and click on the downward pointing arrow button.
3. Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the Utilities menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu. Select Restart from the Apple menu.
4. Reinstall Lion/Mountain Lion, Mavericks: Reboot from the Recovery HD. Select Reinstall Lion/Mountain Lion, Mavericks from the Utilities menu, and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless. -
HT1338 How to go back to lion from mountain lion????
Plese explian, How to go back to lion from mountain lion?
Time Machine does not provide bootable backups. Therefore, this is not the solution.
If you bought Lion, you should be able to re-download it from the Mac App Store. (Sadly, Apple pulled the ability to actually buy Lion off the store). You should be booted to another volume other than the one you will be installing to. You may have to disable the installation on the disk you wish to move back to Lion. I'm not certain, but suspect that trashing the ML System folder would do the job. The Installer will probably notice the missing OS and allow the Lion install. If not, then you'd have to go to the root directory of that volume, make invisible files visible and trash the 'Kernel' files and try again to install Lion.
Ideally you can use the Time Machine backup to restore just about everything else. But you may find everything works fine after the install.
I beta tested 10.8 Mountain Lion and know that it had a couple remaining bugs upon release. That's what updates are for. I expect there will be a rapid release of 10.8.1 update via the Mac App Store. It may well be worth hanging in there with 10.8. It is most definitely an IMPROVEMENT over Lion, whose Finder bugs I absolutely hate. (But that problem may soon be solved with the 10.7.5 update coming soon).
If you look around the net you'll find there are instructions for creating a bootable Lion installer DVD or USB thumb drive as long as you have the Lion Installer on a hard drive. Here are a couple with illustrations:
http://osxdaily.com/2011/06/21/mac-os-x-lion-clean-install-explained/
http://mashable.com/2011/07/20/lion-clean-install-guide/
Maybe you are looking for
-
Updating a view after modifying a table...
Hello, Here is the scenario. I have a a table in HANA with 50+ columns of data. I have created both Attribute and Analytical views of that data. These views have been activated and deployed. Now I need to modify my table to add two new columns tha
-
I Was trying to update to the latest version; i uninstall to download new version because it wasn't letting me update. Now it wouldn't open at all because "The file"iTunes.Library.itl"cannot be read because it was created by a newer version of iTunes
-
Batch changing iPhoto photo dates.
I've imported several thousand scanned photos into iPhoto 7.1.3, and changed the dates to the dates they was taken either by modifying the information window, or by using batch date change. My intention was to modify the original files so that export
-
Tabulation and arrow keys don�t work through ssh
Hi! I just got a solaris 10 on a v240. But I loggin through SSH, tabulation key and arroy keys don� t work. It � s quite nasty because I cannot just repeat a command for example, I�ve to type it allover again. I� m quite surprised because I have an o
-
HT3180 How can I restart the AppleTV using iTunes?
I need to restart my AppleTV (according to other support posts) but I the remote restart and/or power down restart doesn't work. I thought I would try using iTunes but iTunes doesn't seem to recognize the AppleTV even though it is connected to the co