Introducing Active Directory sites AFTER exchange 2013 installation
Hi
We have multiple physical sites and only 1 active directory site. Email environment is pure on-premises exchange 2013. Each physical site has CAS/Mailbox servers. There are not IP restrictions between these physical sites. Everything
is outlook anywhere obviously.
I would like to introduce NEW AD sites for each of these physical locations.
Do you see any major issues that I need to be aware of?
Can this be done in the middle of the day?
Will there be pop ups in outlooks and disconnects?
I appreciate your help.
I haven't had to do this before, but I would probably schedule this at night as there are some changes that will need to be made on the Exchange side of things.
Once you have the new AD Sites configured (Make sure you have at a minimum one Global Catalog, although I would recommend at least 2 in each AD site). You should cycle the AD Topology Service on each Exchange Server (this is going to cause all services
to restart so do it one at a time).
You should also use Set-ClientAccessServer and set the proper site scopes that you want Autodiscover to respond to.
I'm sure there's more, but that's what I can think of at the moment.
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread
Similar Messages
-
Active Directory Sites and Exchange 2013 Deployment
I've recently took over responsibility of an Exchange 2013 Organization that is deployed as follows:
Active Directory consists of 4 Sites. AD Site A, B, C, D Exchange 2013 Enterprise resides in 2 of the 4 AD Sites as follows:
AD Site A - ExchangeServer 1 and ExchangeServer 2
AD Site B - Exchange Server 3
AD Site C - No Exchange Servers
AD Site D - No Exchange Servers
All 4 AD Sites are 4 different Physical locations/datacenters. All 3 Exchange 2013 servers are multi-role servers.
The Forest in which Exchange resides in consists of an empty Root domain, a Production (child) domain and a Test (child) domain. Exchange resides in the Production (child) domain.
Issue: AD Site A contains DC's from all 3 domains: Root Domain, Production child Domain (this is where Exchange lives) and Test child Domain. I notice that Exchange in AD Site A is using DC's from the Root Domain for it's "DefaultGlobalCatalog",
"DefaultConfigurationDomainController" and "DefaultPreferredDomainControllers" This to me does not seem to be very efficient as any Address Book queries will have to be referred to by the Root Domain DC's to the Production child domain
where Exchange lives. All of the AD User accounts and mailboxes are in the Production child domain.
In a situation such as this, would it be advisable to build 2 additional AD sites specifically for Exchange? Rather than re-IP Exchange or risk the impact of moving several other (non exchange) servers to another AD site, I would add the IP address
of the Exchange servers /32 to the new Exchange dedicated AD Sites and erect a DC in these new sites adding its IP address /32. Any thoughts on this idea? If the subnet that exchange resides on is (for example) 10.60.3.0 /16 in AD Site A, and
I build a new AD site for Exchange and add the IP address of the Exchange server such as 10.60.3.141/32 for this new Exchange AD Site boundary, I can still leave the 10.60.3.0 /16 unaffected in AD Site A, correct?
I'm looking for Microsoft's best practices in terms of laying out AD and domain controllers pertaining to Exchange server 2013.Hi Anthouyray,
Thank you for your question.
We could use the following command to exclude domain controller which is root domain controller:
Set-ExchangeServer –Identity <exchange servername> -StaticExcludeDomainControllers <root domain controller>
Then we could restart the service of “Microsoft Exchange Active Directory Topology” to check if the issue persist.
If there are any questions regarding this issue, please be free to let me know.
Best Regard,
Jim
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact [email protected]
Jim Xu
TechNet Community Support -
I have a two site DAG, and the command is running from the alternate site where the databases are not currently being hosted. The following command...
Test-OutlookConnectivity -Protocol:TCP -TrustAnySSLCert:$true -MonitoringContext:$true
...errors with the following output:
An error occurred while trying to access mailbox CurrentlyHostingMBServerName.InternalDomainName, on behalf of user InternalDomainName\extest_bb13200232474
Additional information:
[Microsoft.Exchange.Data.Storage.WrongServerException]: The user and the mailbox are in different Active Directory sit
es..
+ CategoryInfo : OperationStopped: (Microsoft.Excha...onnectivityTask:TestOutlookConnectivityTask) [Test-
OutlookConnectivity], CasHealthStorageErrorException
+ FullyQualifiedErrorId : F2F8AC0D,Microsoft.Exchange.Monitoring.TestOutlookConnectivityTask
I thought this command would work based on the 'AllowCrossSiteRpcClientAccess: True' option on the DAG. The command works well if run a CAS server in the active DB site.Hi,
Exchange 2013 users use Outlook Anywhere to connect to CAS server. You may run the RCA to test the connectivity:
https://www.testexchangeconnectivity.com/
Thanks,
Simon Wu
TechNet Community Support -
Re-Create the "Exchange" virtual directory in the "Exchange Back End" Site on Exchange 2013
Sorry for this stupid question.
In IIS, I accidentaly deleted the "Exchange" virtual directory in the "Exchange Back End" Site on Exchange 2013 (Mailbox Role).
What I need to know is the physical path to re-create it.
ThanksCheck http://blogs.technet.com/b/get-exchangehelp/archive/2013/02/07/managing-exchange-2013-iis-virtual-directories-amp-web-applications.aspx
-
Route mail and Active Directory Sites and Services configuration
Folks,
I have a problem in the internal email routing. My network is spread across various regions and the branch offices are connected together in a mpls network (full mesh). Every region has its own Exchange Server with all roles installed and the smtp connection
to the outside world is linked to two Exchange servers in the headquarter server farm.
The problem is that internally I often see emails going across the Exchange Servers in the branch offices where there is low bandwidth (from 3 to 5 Mbps), thus email are sent first to these servers instead of going immediately to the Exchange hosting
the mailboxes of the intended recipients. This happens also with inbound emails.
This causes slowness in the email system and sometimes also the network with these branch offices suffers from packet loss or very high latency.
I know that Exchange is a site-aware application and uses the Active Directory topology for message routing and to communicate with the services that are running on other Exchange 2013 computers. For this reason I have checked the Active Directory Sites
and Services and surprisingly I have found that there are no sites, no subnets, nothing has been defined but the default settings, included the Inter-Sites transport which contains the default DEFAULTIPSITELINK.
Apart from the fact that clients use logon servers which are not supposed to use in the far remote offices, I am concerned of changing the Exchange Infrastructure whilst the email system is running and I would like to ask your opinion about my next steps:
1) Create subnets for every office
2) Create sites and then link them to the subnets done in point 1
3) Delete the DEFAULTIPSITELINK and create new site links based on the costs (network speed) in order to determine the best routing server. I have 5 remote offices with 5 different network bandwidth, so I'll have to create 5 IP site links: high cost for
link with slow network, low cost for fast network.
4) (Optional) Configure the Exchange-specific cost using the Set-AdSiteLink cmdlet to the AD IP site links created previously
Apart from the valid questions on why the previous Exchange Administrator have forgotten to set up the Active Directory (Topology) Sites and Services...
...And why have chosen to install all Exchange Roles to each server when there was no reason to do that (there are two servers connected to the external smtp gateways in the headquarter, so in my opinion the Exchange Servers in the remote branch offices
should have had only the mailbox and the cas role)...
As a matter of fact, my idea is to go further and create the sites,subnets and the ip site link. If I still notice a wrong email flow, I can configure an ad-hoc Exchange-specific cost using the Set-AdSiteLink cmdlet. Does this sound reasonable to you guys
or I am taking the wrong decisions?
ThanksThank you very much for your link. This is exactly the page I have read just before posting my question here. It is not easy for me to understand why this has been setup this way by a Microsoft certified engineer.
There are specific rules to follow when Active Directory and Exchange are located in multiple sites and I am not a skilled Exchange Administrator... he keeps saying that it is correct and also tells that if I go forward with my ideas there is the
risk to increase the level of complexity. I prefer more complexity than default setting, and as a consequence of that, connectivity problems!
Hopefully everything goes well. I will post my results here once I have done the changes
Regards -
Exchange 2013 installation Problem on Hyper-V
Hello,
I have a very interesting problem Exchange 2013 installation step on Hyper-V.
I have 2 server. I installed on server Server 2012 R2 Standart. And then installed hyper-v role for both server.
I created virtual machine for first server and this virtual machine domain controller.
And then I created virtual machine for second server and this virtual machine Exchange 2013.
I installed all prequisites and exchange 2013 finished successfuly. When I opened https://server/ecp it give me http 500 internal error. I checked almost all forums but any recommendation didn't solve my problem.
And then I removed hyper-v role and installed vmware v11. and installed same applications like above.
Very interesting finished installation and opened ecp console. eveythink seen to good.!
Actualy I find problem.
There is exchange feature installation command on microsoft exchange prequisite. When ruunning this command installing two program on program and feature name is "c++ redistrubutable x64 and x32"
I must uninstall this programs before install unified communication api 4.0.
I cannot see on hyper-v when running this feature.
But I can see on vmware this features on programs and feature.
This is very absurt.
Anybody have an idea for this
Thank you for your clarify.Hi,
Thanks for your reply.
I run this command before Exchange 2013 installation:
Install-WindowsFeature AS-HTTP-Activation, Desktop-Experience,
NET-Framework-45-Features, RPC-over-HTTP-proxy, RSAT-Clustering,
RSAT-Clustering-CmdInterface, RSAT-Clustering-Mgmt, RSAT-Clustering-PowerShell,
Web-Mgmt-Console, WAS-Process-Model, Web-Asp-Net45, Web-Basic-Auth, Web-Client-Auth,
Web-Digest-Auth, Web-Dir-Browsing, Web-Dyn-Compression, Web-Http-Errors, Web-Http-Logging,
Web-Http-Redirect, Web-Http-Tracing, Web-ISAPI-Ext, Web-ISAPI-Filter, Web-Lgcy-Mgmt-Console, Web-Metabase,
Web-Mgmt-Console, Web-Mgmt-Service, Web-Net-Ext45, Web-Request-Monitor, Web-Server, Web-Stat-Compression,
Web-Static-Content, Web-Windows-Auth, Web-WMI, Windows-Identity-Foundation
later run this code on vmware platform , installing 2 program in programs and feature. name is Visual
C++ Redistributable package x64 and x86. I know Unified Communications Managed API 4.0
install same program too. But I must unintall Visual C++ Redistributable package before
install Unified Communications Managed API 4.0. But My problem I cannot see this two program
in programs and feature on hyper-v platform.
I tried it many times. -
The user and the mailbox are in different Active Directory Sites
Hi All,
I have 2 site, each site have an Exchange Server 2010 SP1, let say Site HQ and Site DRC I monitored it with SCOM 2007 R2, site HQ successfully monitored, then I continue try to monitor DRC site. I executed new-TestCasConnectivityUser.ps1 at MBX DRC Site
to create extest user.
Then I try to execute command to test-connectivity, but it failed.
Test-OwaConnectivity -TestType:Internal -MonitoringContext:$true -TrustAnySSLCertificate:$true -LightMode:$true | fl
RunspaceId : 6b709fa5-0719-4be5-ae62-ec4b3617a6e0
AuthenticationMethod :
MailboxServer : CONMBX02.contoso.com
LocalSite : CONMBX02.contoso.com
SecureAccess : False
VirtualDirectoryName :
Url :
UrlType : Unknown
Port : 0
ConnectionType : Plaintext
ClientAccessServerShortName : DRCCAS01
LocalSiteShortName : CONMBX02
ClientAccessServer : DRCCAS01.contoso.com
Scenario : Reset Credentials
ScenarioDescription : Reset automated credentials for the Client Access Probing Task user on Mailbox server CON
MBX02.contoso.com.
PerformanceCounterName :
Result : Failure
Error : [Microsoft.Exchange.Monitoring.CasHealthStorageErrorException]: An error occurred while t
rying to access mailbox CONMBX02.contoso.com, on behalf of user contoso.com\extes
t_xxxxxxxx
Additional information:
[Microsoft.Exchange.Data.Storage.WrongServerException]: The user and the mailbox are in
different Active Directory sites..
UserName : extest_xxxxxxxx
StartTime : 04/01/2012 20:46:19
LaCONcy : 00:00:00.0156460
EventType : Error
LaCONcyInMillisecondsString :
Identity :
IsValid : True
WARNING: No Client Access servers were tested.
RunspaceId : 6b709fa5-0719-4be5-ae62-ec4b3617a6e0
Events : {Source: MSExchange Monitoring OWAConnectivity Internal
Id: 1005
Type: Error
Message: Couldn't access one or more test mailboxes.
The service that is being tested will not run against these mailboxes.
Detailed information:
Local Site:DRCProduction
[Microsoft.Exchange.Monitoring.CasHealthStorageErrorException]: An error occurred while trying to
access mailbox CONMBX02.contoso.com, on behalf of user contoso.com\extest_xxxxxxxx
Additional information:
[Microsoft.Exchange.Data.Storage.WrongServerException]: The user and the mailbox are in differen
t Active Directory sites..
PerformanceCounters : {Object: MSExchange Monitoring OWAConnectivity Internal
Counter: Logon LaCONcy
Instance: DRCCAS01.contoso.com|DRCProduction
Value: -1000}
any help appreciate it.
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread.
Krisna Ismayanto | My blogs:
Krisna Ismayanto | Twitter: @ikrisnaHi
Removed existing test account on two site.
Then created test account on DGC through new-TestCasConnectivityUser.ps1.
Flushed Health Service on RMS.
Terence Yu
TechNet Community Support
Hi
What do you mean on DGC ? you mean I have remove both test account or just at DRC site only ?
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread.
Krisna Ismayanto | My blogs:
Krisna Ismayanto | Twitter: @ikrisna -
Disaster Recovery site for Exchange 2013
Hi, I have to build DR site with Exchange 2013 environment and unable to see document for Exchange 2013 perspective.
In new environment will contain 10 CAS/MBS co-located servers in primary datacenter with two mailbox copies and disaster recovery site with 5 Exchange 2013 CAS/MBS co-located servers with one database copy in blocked activation mode. Any document related
to this screnario would be helpful. The required solution is when all the servers in PDC goes down then DR site would be activated at DMZ level and Server level. Can I use same IP subnet/Site for the DR site?Hi,
Yes, you can use the same subnet for DR site. If you use the same subnet, you need to use stretched VLAN.
Here is a related thread for your reference. (This case is for Exchange 2010, but it also applies to Exchange 2013 DAG deployment)
http://social.technet.microsoft.com/Forums/exchange/en-US/80ca452f-f950-4496-83e8-3067d571bb57/exchange-2010-dag-across-sites-different-subnets-vs-stretched-vlan?forum=exchangesvravailabilityandisasterrecovery
Best regards,
Belinda Ma
TechNet Community Support -
Replication with Domain and Sub domain in Active directory sites and services
I seen many AD enviroments and know that when you have mutiple DCs you use Active Directory Sites and services to replicate using the NTDS Settings. If you have a Domain and sub domain do you need to do this as well or does it sync up automatically because
it's a sub domain? A see a couple of domains where the NTDS settings isn't being used to snyc with the child domain. Just wondering if that is normal or will it cause authentication errors?I seen many AD enviroments and know that when you have mutiple DCs you use Active Directory Sites and services to replicate using the NTDS Settings. If you have a Domain and sub domain do you need to do this as well or does it sync up automatically
because it's a sub domain? A see a couple of domains where the NTDS settings isn't being used to snyc with the child domain. Just wondering if that is normal or will it cause authentication errors?
Two way transitive trusts are configured automatically when you create a child domain or tree root domain. You don't have to worry about site/subnet or replication part at least from trust perspective. But make sure site's names are unique in each domain.
How Domain and Forest Trusts Work
http://technet.microsoft.com/en-us/library/cc773178%28v=ws.10%29.aspx
http://technet.microsoft.com/en-us/library/cc730868.aspx
http://blogs.technet.com/b/askds/archive/2008/09/24/domain-locator-across-a-forest-trust.aspx
Awinish Vishwakarma - MVP
My Blog: awinish.wordpress.com
Disclaimer This posting is provided AS-IS with no warranties/guarantees and confers no rights. -
HTTP 500 ERROR AFTER EXCHANGE 2013 SP1 INSTALL
Help after exchange 2013 sp1 new install unable to get to the ECP or OWA page with HTTP 500 error in IE the install went ok but not sure what can be causing the error any help would be appriciated.
EXCHANGE 2013--SP1 on WIN2K12--R2 Standard
TY
M4326See the following:
http://social.technet.microsoft.com/Forums/exchange/en-US/08d3777c-dc03-4411-8c87-7db37d2f406a/exchange-2013-owa-login-error-http-500?forum=exchangesvrclients
CK -
SCCM 2012-Active Directory Site
Hello All,
I was create the collection by name of IN-ACTIVE for India location but in that collection USA systems also falling then when I was check those all USA machines the Active Directory site name showing different OU name
Here my Goal is :
Why other Country machines reporting to this collection and AD site name also showing another not USA OU ?
Anyone can help me
Best Regard's Krishnaif you are sure that,US computers are not in India location OU ,you may check by picking up one US computer(that you feel,it is part of India OU Collection ),properties ,and look for its OU details.
Can you post your WQL Query ?
Eswar Koneti | Configmgr blog:
www.eskonr.com | Linkedin: Eswar Koneti
| Twitter: Eskonr -
Exchange 2013 SP1 Object is corrupted and inconsistent state after Lync 2013 Installation
Hi Fellows,
I am facing an issue with Exchange 2013 SP1 (5.0.847.32)
environment. I recently installed Lync 2013 (version: 5.0.8308.0) a week ago and just recently start getting the below error when configuring delegation or modifying the users/groups from Exchange Control Panel:
"The Object <object DN> has been corrupted, and it's in an inconsistent state. The following validation errors happened:
The access control defines the ObjectType <object guid> that can't be resolved.."
I can see some forum threads with same issue (links given below) but unable to find if this is a known issue and how to get it resolved. Need assistance if anyone has faced same and could help me out to figure it.
http://social.technet.microsoft.com/Forums/exchange/en-US/72310530-d1de-4b39-a0fb-1592247df03f/access-control-entry-issue-after-installing-lync-2013-into-the-forest?forum=exchangesvrdeploy
http://www.networksteve.com/exchange/topic.php/Issue_with_exchange_2013_lync_2013_intergration/?TopicId=37192&Posts=2
J.AHi
Usually the affected SID objects are referring to deleted objects.
Use the PsGetSid tool to try to resolve them. -
Active Sync not Working - Exchange 2013 with Exchange 2007
Hi
Recently we introduced Exchange 2013 servers to our existing Exchange 2007 organization. The servers are just configured with default self-signed certificate and URLs are pointing to server FQDNs.
Everything is at default as far as configuration is concerned in Exchange 2013.
After just introducing the Exchange 2013 CAS servers was checking the ActiveSync functionality using a new mailbox created on Exchange 2013. We have not yet published our Exchange 2013 servers to
Internet (before even doing that, want to ensure ActiveSync is working). We're connecting using our Private network and trying to make a connection to CAS FQDN. Checked a iOS7 (iPad) and a Windows Phone device, both of them configure successfully (with the
certificate warning, which is obvious) but when it comes to synchronizing the contents they fail saying "Cannot Get Mail. Connection to Server Failed"
Checked the IIS Logs on CAS server and found that the device makes a successful connection - as is indicated by successful configuration but thereafter nothing happnes on the device and no error
logged in Event Viewer as well. Could it be that the mailbox server is denying the connection....how to check. How to go ahead with the troubleshooting.
Everything else expect ActiveSync is working perfectly. Tries accessing the ActiveSync VD using the link
HTTPS://Server_FQDN/Microsoft-Server-ActiveSync, this pops-up a window asking for credentials – which is normal behavior indicating ActiveSync virtual directory is good.
Thanks
Taranjeet Singh
zamnHey Guys
Just to update here my initial testing revieled that if I run Test-ActiveSyncConnectivity by not specifying the -URL parameter like this:
Test-ActiveSyncConnectivity -MailboxCredential (get-credential User1) |FL
the command fails for an obvious reason as shown in the result. The command is getting the mailbox server name in the ActiveSync URL returned automatically:
ClientAccessServer
: SITE-MBX-02.ABC.COM
Scenario
: Options
ScenarioDescription
: Issue an HTTP OPTIONS command to retrieve the Exchange ActiveSync protocol version.
PerformanceCounterName
: DirectPush Latency
Result
: Failure
Error
: The OPTIONS command returned HTTP 200, but the Exchange ActiveSync header
(MS-Server-ActiveSync) wasn't returned. The request likely did not reach a
Client Access
server, either because
- A proxy server intervened (check the headers below for any that may have been
returned by a proxy)
-The virtual directory could not be reached:
https://SITE-MBX-02.ABC.COM/Microsoft-Server-ActiveSync
- The virtual directory does not point to a Client Access server:
https://SITE-MBX-02.ABC.COM/Microsoft-Server-ActiveSync
If however, I manually provide the -URL parameter value with FQDN of CAS server:
Test-ActiveSyncConnectivity -URL
https://SITE-CAS-02.ABC.COM/Microsoft-Server-ActiveSync
-MailboxCredential (get-credential User1) |FL
it succeeds.
We have our CAS and Mailbox servers installed on separate systems - no colocation.
This is strange and makes me curious to find out, where does the command without -URL parameter is getting the ActiveSync URL that has mailbox server in it. I checked that the new Exchange 2013 CAS servers have InternalURL parameteres populated with their
own FQDNs and the ExternalURL is empty for now.
Need help in drilling down this further.
Thanks
Taranjeet Singh
zamn -
Exchange 2013 installation fails
We're in the process of migrating from Exchange 2007 to Exchange 2013. I've followed the prerequisites, and have the necessary account permissions, but when I start the installation it fails at step 1 of 5 (mailbox role:mailbox service).
This warning shows up in the application log:
Event ID 2397
Process ExSetupUI.exe (PID=9844). Object [CN=Mailbox Database 1783948598,CN=Databases,CN=Exchange Administrative Group (FYDIBOHF23SPDLT),CN=Administrative Groups,CN=<domain>,CN=Microsoft Exchange,CN=Services,CN=Configuration,DC=<domain>,DC=local]. Property [Server] is set to value [<Exchange 2013 server name>
DEL:492ae292-f89f-4a29-b009-22a60973a4bf], it is pointing to the Deleted Objects container in Active Directory. This property should be fixed as soon as possible.
This error shows up in the Exchange install console, as well as the application log:
Event ID 1002
Exchange Server component Mailbox role: Mailbox service failed.
Error: Error:
The following error was generated when "$error.Clear();
if (($RoleIsDatacenter -ne $true) -and ($RoleIsDatacenterDedicated -ne $true))
if (test-ExchangeServersWriteAccess -DomainController $RoleDomainController -ErrorAction SilentlyContinue)
# upgrade the discovery mailboxes to R5 version, this will fix the RecipientDisplayType property of the discovery mailbox which was wrong in R4.
get-mailbox -RecipientTypeDetails DiscoveryMailbox -DomainController $RoleDomainController | where {$_.IsValid -eq $false} | set-mailbox -DomainController $RoleDomainController
$name = [Microsoft.Exchange.Management.RecipientTasks.EnableMailbox]::DiscoveryMailboxUniqueName;
$dispname = [Microsoft.Exchange.Management.RecipientTasks.EnableMailbox]::DiscoveryMailboxDisplayName;
$mbxs = @( get-mailbox -Filter {name -eq $name} -IgnoreDefaultScope -resultSize 1 );
if ( $mbxs.length -eq 0)
$dbs = @(get-MailboxDatabase -Server:$RoleFqdnOrName -DomainController $RoleDomainController);
if($dbs.Length -ne 0)
$mbxUser = @(get-user -Filter {name -eq $name} -IgnoreDefaultScope -ResultSize 1);
if ($mbxUser.Length -ne 0)
enable-mailbox -Discovery -identity $mbxUser[0] -DisplayName $dispname -database $dbs[0].Identity;
else
write-exchangesetuplog -info "Skipping creating Discovery Search Mailbox because of insufficient permission."
" was run: "The Exchange server for the database object "Mailbox Database 1783948598" wasn't found in Active Directory Domain Services. The object may be corrupted.".
I should also mention that this installation was attempted once before by an ex-coworker, and it failed. I've spent hours searching Google but haven't come up with a solution. Does anyone have any ideas?Check it at Exchange 2007 side, Get-MailboxDatabase -Server E2007ServerName or via EMC to confirm but if msExchOwningServer/msExchMasterServer
points to the server which is stale 2013 server then it shouldn't be connected to E2007 by any way and you are good to remove those...
But I wouldn't touch another DB which has just server name and not servername\0ADEL:guid
as it is not giving error (at least yet...) in the setup
Blog |
Get Your Exchange Powershell Tip of the Day from here -
Create a User account in active directory from SharePoint online 2013 list data
Hello,
I am trying to create a SharePoint list through which i can create a user account into active directory,
1 - HR is sending the detail in the email body to a Specific email address ([email protected]) like below..
First Name: XYZ
Last Name: ABC
Address: ABC 123
Designation: Analyst
Employee ID: 10492
and so on
2 - I need to pickup every new email data of the above section into sharepoint list (in Column)
First Name Last Name Address Designation Employee ID
3 - I want to create a event receiver through which i can go ahead and find the new data in the list and then create a user in the active directory,
I tried very hard and since i dont have much experience in coding part, any help will be highly appreciated
Thank you
Aman1- Configure Incoming Email Setting at your SharePoint Farm -
https://technet.microsoft.com/en-us/library/cc262947.aspx
http://blogs.technet.com/b/harmeetw/archive/2012/12/29/sharepoint-2013-configure-incoming-emails-with-exchange-server-2013.aspx
2- Configure your Sharepoint List Incoming e-mail settings for [email protected] - ListSetting-Communications->Incoming e-mail settings. -
https://support.office.com/en-in/article/Enable-and-configure-e-mail-support-for-a-list-or-library-dcaf44a0-1d9b-451a-84c7-6c52e7db908e
3- Write an Incoming Email Receiver , and Add you Email Body Parsing Code (retrive value of fields , firstname , lastname etc) in
EmailReceived() method. also add the code for adding new user in Active Directory
http://blogs.msdn.com/b/tejasr/archive/2010/03/06/event-handler-code-to-add-incoming-emails-with-subject-discussion-id-as-replies.aspx
https://pholpar.wordpress.com/2010/01/13/creating-a-simple-email-receiver-for-a-document-library/
4- Active Directory Code Help -
http://www.codeproject.com/Articles/18102/Howto-Almost-Everything-In-Active-Directory-via-C
http://www.codeproject.com/Tips/534718/Add-User-to-Active-Directory
Thanks
Ganesh Jat [My Blog |
LinkedIn | Twitter ]
Please click 'Mark As Answer' if a post solves your problem or 'Vote As Helpful' if it was useful.
Maybe you are looking for
-
Very new to photoshop I am trying to make changes to a photo and set it up as a smart object but after selecting smart object, the checkerboard appears and my photo dissppears
-
Is it possible to add an OS to solaris multiboot sytem?
Hi Thank you for reading my post Is it possible to add an OS to solaris Boot system? for example Solaris X86 is installed on SATA Disk number 1 and Windows is installed on Sata Disk number 2. System boot on Solaris Hard disk and I want to add an opti
-
How can I import F4V or flv files
I downloaded some videos from tudou.com ,I want to edit them ,but it seems that i can't import them to PR cs6 , They are f4v files ,and some flv files also can't be imported, my win8 system had installed win8 codecs ,but no work ,i changed w
-
Image capture not recognizing itouch
image capture not recognizing itouch. it did once until i rebooted
-
E70 Text messages take an age to send
Hi, I wonder if anyone can offer advice. Generally the E70 is pretty cool but It takes an age to send a text message and I cannot use the phone whilst it is sending. I have deleted all messages etc but no joy. Any advice please?