Iomega Storcenter ix4-300d stuck at 95% after firmware upgrade

Hi,
I upgraded my device after I got an email that there is a new firmware:
An update to version 3.2.10.30101 of the Iomega StorCenter ix4-200d software is now available
I installed the update but now it is stuck at 95% after rebooting.
Never had any problem before the firmware upgrade.
Any advice?

Hello BelgianTomas
I recommend that you first power down the unit if the unit has not completed the boot process. Then re-seat all disks and try booting the unit again. Please do not try to access the web interface until the power led is solid white.
Next would be to try moving the internal disks to different bays to see if a different drive order wil allow the unit to boot.
If that does not help, LenovoEMC suppor should be contacted for more advanced options.
LenovoEMC Contact Information is region specific. Please select the correct link then access the Contact Us at the top right:
US and Canada: https://lenovo-na-en.custhelp.com/
Latin America and Mexico: https://lenovo-la-es.custhelp.com/
EU: https://lenovo-eu-en.custhelp.com/
India/Asia Pacific: https://lenovo-ap-en.custhelp.com/
http://support.lenovoemc.com/

Similar Messages

SRW2024 Stuck in Loop after Firmware upgrade.

When connected to the serial port the following continues to loop:
------ Performing the Power-On Self Test (POST) ------
UART Channel Loopback Test........................PASS
Testing the System SDRAM..........................PASS
Boot1 Checksum Test...............................PASS
Boot2 Checksum Test...............................PASS
Flash Image Validation Test.......................PASS
BOOT Software Version 1.0.0.03 Built 08-Jun-2004 09:48:10
CPU - FireFox 88E6218 ARM946E-S processor
64 MByte SDRAM. I-Cache 8 KB. D-Cache 8 KB. Cache Enabled.
Autoboot in 2 seconds - press RETURN or Esc. to abort and enter prom.
Preparing to decompress...
Decompressing SW from flash
HOSTG_rscode_file_load: could not load file
Perform WARM BOOT ...
When I attempt to do download the new software with XModem the firmware (fw) completes successfully (ls20xx_Salsa-12222.ros) but the boot image fw fails (runtop_boot-101.rfb) and I receive this message:
    Startup Menu
[1] Download Software
[2] Erase Flash File
[3] Password Recovery Procedure
[4] Set Terminal Baud-Rate
[5] Back
Enter your choice or press 'ESC' to exit:
Downloading code using XMODEM.
-- Download complete --
Wrong file format. Writing aborted.
Is there a different version of the firmware perhaps an older version available for download somewhere? Or is there something I am doing wrong?
Any help would be greatly appreciated.
We have 2 - srw2024's and 2- srw2016's. Issue only on the one with the fw upgrade.
Thanks.

Here is what I've found to be useful and so far seems like a fix for myself.
I downloaded an older firmware version 1.0086 from here
http://ip.gliebetronics.com:800/firmware/Linksys%20SRW2024/Firmware/
runtop-10086.ros
The other 2 versions may help some other people on this forum.
Uploaded it through the serial port with Xmodem.
So far I've been able to boot and now access through web interface. I will post later on how it is doing later in the day.

User quota update bug on Iomega StorCenter ix4-200d - 2.1.42.18967

Hi everyone,
my device is Iomega StorCenter ix4-200d running firmware version 2.1.42.18967
Last week user X on my device exceeded his personal folder's default quota (2 GB): I told him to move exceeding data away from the storage device and he did so.
Now he only has 300 MB under his folder, but the the device's web interface is still complaining about userX using 50 GB of space and therefore exceeding his quota. Furthermore, user X is not allowed to put more data into his personal folder, even if only stores 300 MB of data...
I tried the following solutions:
reboot the device
disabled quota on user X's personal folder and then re-enable it again
but none worked. How can I fix the issue?
Any help/hint would be appreciated. Thanks in advance

Hello sanzso
I highly recommend you contact LenovoEMC PX12 support in your region regarding this issue.
a quick suggestions though. If media server is enabled, in some situations there can be an issue causing a data usage mis-match. Usually this would only show the "others" listing to show as having a strange usage level.
To correct this, media server would need to be turned off, copy the share data to a new share or external storage device, delete the existing share(s) then restore the data to the new share(s).
LenovoEMC Contact Information is region specific. Please select the correct link then access the Contact Us at the top right:
US and Canada: https://lenovo-na-en.custhelp.com/
Latin America and Mexico: https://lenovo-la-es.custhelp.com/
EU: https://lenovo-eu-en.custhelp.com/
India/Asia Pacific: https://lenovo-ap-en.custhelp.com/
http://support.lenovoemc.com/

Iomega StorCenter ix4-200d iSCSI performance

Hi there, just looking for some help here, we have an Iomega StorCenter ix4-200d device that was not in use and I tried to make a drive for storing media files and moving them from the file server. I have created an iSCSI disk and connected to a Windows 2008R2 using an iSCSI Initiator, the Iomega box comes with two network interfaces that were previously bonded, the connection was quick and easy to setup, the problem that I am having is performance. When transferring small file/s the transfer is quick and effective, but if the file/s pass more than 1GB windows explorer crashes and the OS get frozen, I have been monitoring the disk use and is horribly high when transferring those files, taking more than 10min for a 1.5GB to transfer, the LAN is 1GB speed. I read about creating specific VLANS only for iSCSI transfers, but we did not have that before and the drive was previously used as iSCSI backup solution, before another solution now in place replaced it Any help or thoughts are more than welcome Juan

GUS_Lenovo, Really helpful your coment, please can someone else let us know if it is having this problem. The setup is very simple a VMware ESXi 5.5 virtual machine, OS 2008R2, connected using passtrough native windows iSCSI initiator to an external Iomega StorCenter ix4-200d drive. I disconnected the target from the troubled server and connected the iSCSI disk to a test server, same setup VMware 2008R2 connected to the pysical iSCSI uing the windows native initiator, no roles on it. I double checked that only the test server was connected into it, same symptom, transfers files up to 500MB are quick and effective, if the file/s to transfer pass 1GB or more the transfer halts and the explorer process on the VM crashes, not very effective for now. Bandwith?? any help very much appreciated

Iomega StorCenter px4-300d share access

Hey guys! I'm having an issue with an iomega StorCenter px4-300d. Recently a contractor remoted in and changed our domain controllers so I ended up doing a network reset on our 2 iomega NAS. The first one behaved in a completely logical fashion and through some trial and error I have it reset as it was before. The second one however is being rather illogical. I have reattached it to the domain and set up share permissions, however users who have been given permission to the shares are unable to access them on this device. The only way I've been able to get to files is to access them through the web interface, but that doesn't lend itself well to managing the data in the shares. I have rebooted both the NAS and my laptop several times, as we have encountered this issue in the past, but usually a reboot of the NAS or the users PC clears it up. Has anyone else encountered this? Any recommendations on the course I should follow? Edit: This is wierd all of a sudden it started letting people into shares. Any recommendations you have would still be great, since it isn't really behaving in a consistent manner.

Hello HCH_Allegro
Is the primary unit showing any drive/storage alerts in the system status page or in the event log?
Do you have media server enabled in the primary unit's web interface? If so, try disabling the feature restart the unit and then try accessing having the remote unit connect the cloud.
Also with the cloud edition devices there are both the Remote Access and Personal Cloud options. If you are trying to have both enabled at the same time it can cause problems like you have been experiencing. Currently Remote Access is no longer online via TZO(DYN), so personal cloud should be the only remote option enabled.
LenovoEMC Contact Information is region specific. Please select the correct link then access the Contact Us at the top right:
US and Canada: https://lenovo-na-en.custhelp.com/
Latin America and Mexico: https://lenovo-la-es.custhelp.com/
EU: https://lenovo-eu-en.custhelp.com/
India/Asia Pacific: https://lenovo-ap-en.custhelp.com/
http://support.lenovoemc.com/

T410i SSD user and master password problem after firmware upgrade

Hello.
I have problem with my Corsair Force 3 120GB SSD. After firmware upgrade of SSD my master and user HDD passwords are no longer valid. I'm stuck on BIOS screen and cannot unlock my SSD. After firmware upgrade procedure i got BSOD. Same happened during firmware upgrade on my previous SSD (INTEL X25-M 80GB) but after restart everything was OK. Please help!
Previous firmware version: 1.3
Current firmware version: 1.3.3
SSD connected to another computer shows RAW partition data, but firmware version is 1.3.3 - seems like update was successful.

My X301 Intel x18 got bricked also after a BIOS update then secure erase (was going to sell it). I plugged it to a USB kit and onto a desktop and it was recognised and able to format. But plugging it back to the lenovo it is still a brick. My lucky star there was warranty it was replaced by lenovo.
You may want to try it and extract the data, if it works. And hopefully you can still format it and made it work pluggin back to the lenovo.

PC-Suite sync fails after Firmware upgrade of E65

After firmware upgrade of E65 PC-Suite stops syncing Calendar & Contacts from outlook. No error messages, just "0 entries has been updated".
- PC-Suite updated to 7.0.9.2
- Outlook 2003
- XP Prof.
Any ideas?
Solved!
Go to Solution.

The funny thing is - the notes are synced???? If I restore some old contacts they'll double up in outlook, so I think the problem is, that the sync app doesn't see the outlook contact & calendar folder.
Does somebody has an idea?

Crippled 192.168.1.1 page after firmware upgrade

hi,
i recently upgraded the firmware of my WRT160N V2 to 2.0.03.
but since then when i login i get a crippled page on 192.168.1.1 with not even a menu. so i cant even downgrade. is there something i can do?

It is good to know that the issue is resolved
After firmware upgrade it is always recommended to reset and reconfigure the router and I think that is why you were unable to see the menu on the setup page of your router.

Ix4-300d stuck at 75% boot

I had to move the nas box to a different room during the intial 5 RAID initialization, and the ix4-300d didn't appear to like that. Since I had no data on the box I went ahead and "clean" the disks using the instructions in the knowledge base, and attempt to set it up a second but it is still stuck at the 75% boot percentage.
It has aquired an IP address on my network, and is pingable but the webpage isn't working, and the only port that is open when I ran a port scanner against the ip address is port 111.
Is the internal operating system stored on internal flash, or the SATA disks in the bring your own disk model?
Solved!
Go to Solution.

Hello Stonedturtle
Are you having this issue on a ix4-300d unit? If you are, please check/try the following. If this is regarding the px6 unit on your other thread, please follow the instructions I left on that thread.
Power down the unit, re-seat all disks that are in the unit, power back on.
If the unit continues to hang @75% for more than 5-10 minutes, it could be one or more of the hard disks causing the process to halt. Try booting the unit without disks to see if the " device not ready..." message appears on the LCD and web UI.
If the unit can boot on it's own, try insering disk #4 into bay #1 and disk #1 into bay #4, leave disk 2 and 3 in the same bays while powered off and then try booting again.
If the unit does not boot on it's own without disks, please contact LenovoEMC support in your region about a firmware imager.
LenovoEMC Contact Information is region specific. Please select the correct link then access the Contact Us at the top right:
US and Canada: https://lenovo-na-en.custhelp.com/
Latin America and Mexico: https://lenovo-la-es.custhelp.com/
EU: https://lenovo-eu-en.custhelp.com/
India/Asia Pacific: https://lenovo-ap-en.custhelp.com/
http://support.lenovoemc.com/

Thumbnails missing ix4-300d after firmware upgrade

Eeverything was working well until the upgrade. I am using a WDTV live and the Ix4-300d together and accessing the NAS via media server on the WDTV. Tried restarting both and checking for updates but the WDTV has no thumnails anymore. I am not a techy but am stumped. Any suggestions

same issue here. i plan to finally call into Lenovo support on this; really annoyed w/the last firmware update. wish i woudl have just stayed on the prev version.

Iomega StorCenter ix4-200d replace all disks

REPLACED DISKS: 4 Hard Drive SEAGATE 1 TB with code ST31000520AS.
Before the replacement, had carried out the firmware upgrade for CC38 as executable: DriveFWUpdater-1.8.exe
Successfully finalized.
After the replacement of 4 discs, the procedure would make a boot by USB to reinstall the OS, right?
But when holding the reset for more than 60 seconds, does not appear on the LCD panel USB image >> Network, does not find the boot from USB.
Is there any other procedure?
Thanks.
Solved!
Go to Solution.

Hello estaile
The "DriveFWUpdater-1.8.exe" utility is just for updating the Seagate firmware to cc38 in the ix4-200d / ix4-200d CE.
to replace all the disks you would need to follow the disk upgrade guide here. Basically if you still have at least one original disk with the Lifeline OS firmware, then you can boot the unit with that disk and 1-3 blank disks, after booting the unit will copy the firmware over. if the web interface requests overwrite, allow the overwrite. after that has finished you can power down, install the 4th disk and boot up the unit. the previously installed disk(s) would then be able to copy the firmware over to the last disk.
If you do not have any original disks with the firmware intact, it will limit your options as some of the legacy firmware imagers are no longer available. I recommend contacting LenovoEMC support in your region at that point to see what options might be available.
LenovoEMC Contact Information is region specific. Please select the correct link then access the Contact Us at the top right:
US and Canada: https://lenovo-na-en.custhelp.com/
Latin America and Mexico: https://lenovo-la-es.custhelp.com/
EU: https://lenovo-eu-en.custhelp.com/
India/Asia Pacific: https://lenovo-ap-en.custhelp.com/
http://support.lenovoemc.com/

StorCenter px6-300d stuck

This week I lost one of my 6 HDD in my StorCenter px6-300d. It just died because a Seagate Barracuda firmware bug.
First... I have warranty until 10/2015, but I am not able to solve this with Lenovo Support in Brazil. (BIG PROBLEM)
Second... To be sure that my data is more secure, I just brought a new HDD (same model than the lost one) and added it to my StorCenter px6-300d. I received a message that the new HDD should be "formated" to rebuild RAID. It has RAID 6 with total 6x 2Tb HDD. However, it is for 2 days working (white light blinking) and display shows 0% done. I am not able to access NAS web interface, or anything.
What I need to do? How to solve this? Thanx.
Solved!
Go to Solution.

Hello allmac
With the five orignal disks there is a sync in progress, I do not recommend disturbing it. The process should have about 24 hours to complete. Please check you logs at that time to see if any of the disks are logging errors. If they are not, try adding the replacement disk to the storage system again via drive management.
LenovoEMC Contact Information is region specific. Please select the correct link then access the Contact Us at the top right:
US and Canada: https://lenovo-na-en.custhelp.com/
Latin America and Mexico: https://lenovo-la-es.custhelp.com/
EU: https://lenovo-eu-en.custhelp.com/
India/Asia Pacific: https://lenovo-ap-en.custhelp.com/
http://support.lenovoemc.com/

ZenV Plus STILL stuck in recovery mode after firmware upgrade

=Hi there,
My ZenV plus opened in recovery mode for no apparent reason... I have tried every option to try to fix it, including downloading and installing the firmware upgrade - this generated a message saying the upgrade was successful but the player will still only start in Recovery Mode after trying to reboot it. So what do I do next? Thanks in advance for any and all helpful suggestions.

AHi,
Can you please try resetting the ZEN V Plus to see if it helps?
To reset the player, use a pin to press the reset button.
Did this happen out of the blue?
Do you have any contents in the player? If you do, please remove them to see if the player is booting up properly.

No power after firmware upgrade on nomad jukebox zen xtra

I have the nomad jukebox zen xtra 30gig that froze up over a year ago after i tried to install the firmware upgrade. After the unsuccessful attempt, the mp3 player stopped working.... I mean no power at all. I've changed the battery and recharged the battery from an outside source...still no luck. I can't even try any of the suggestions anyone gives on this site because I have no power.Does anyone have this problem? More important, does anyone have this problem and know of a solution?I've already set my pc back to wmp 0, I have the firmware on the desktop waiting. Now all I need is some power on this unit so that i can try some of the suggestions that seems to be working for people. Thank you

I have the same problem too, but my unit is a?Creative Normad Junebox Zen Xtra 40GB. I was trying to find a solution to my problem when I read about your problem. I have pressed the reset button, on / off switch, removed the battery, reinstalled the battery, and nothing seems to work. I was hoping you?might get a solution to this problem, so that I might be able to fix my MP3 player. If I hear of a solution, I will let you know, thanks for sharing. Issue:? While updating the firmware to the Zen Xtra 40 GB, the unit powered down and?has never came on again. There seems to be no real reason why the unit should not power up. The battery and the AC adapter are working correctly. I am very disappointed in Creative...

No contacs after firmware upgrade on N70

Hi
I did a firmware upgrade yesterday on my N70 using NSU. Of course I did a backup using the uptodate Nokia PC suite. After the firmware upgrade I saved the data back to the phone aagin using the Nokia PC suite. Everything looks good except that no contacts are there.
I did the upgrade again just to make sure that everything went OK with the same result.
Can some help or has the same problem?
Firmware V 5.0638.3.0.1 18-09-06 RM-84
PC Windows XP SP2
Nokia PC Suite 6.82.22.0
NSU 1.2.0en
Best regards
Chris

not sure about your PC Suite version but this has been well documented in these forums and I had the same problem and with N70. I think it was mentioned as a PC Suite issue, or a combined PC Suite issue N70 issue with many people reporting it. Anyway nothing you can do but enter your contacts or transfer from another phone

Iomega Storcenter ix4-300d stuck at 95% after firmware upgrade

Similar Messages

Maybe you are looking for