IOS Devices can't connect to RV220W

I just installed this WAP, updated the firmware. Windows computers can connect. iPads and iPhones can't connect. All iOS devices are runnign 6.01. The iPad can see the nework and it says it joins, but it can't browse the Internet. The iPhone does not even see the SSID.
The WAP is pretty much at the defaults. I am using WPA personal, 5GHz. The iOS devices were working fine with the Netgear that was installed previousley.
I checked this article and the WAP seems to be configured right:
http://support.apple.com/kb/HT4199
What am I missing?
Thanks

Well, what is the country that is configured on the device?
How far the devices from the WAP?
I would suggest two things:
First: to move your thread to small-business wireless forum. They can help you better.
Second: try upgrading the firmware on your RV220W device to latest.
HTH
Amjad
Rating useful replies is more useful than saying "Thank you"

Similar Messages

  • IOS devices can't connect automatically to known wifi network anymore (only manually)

    Hi there.
    Just changed my old wifi router belkin 54g with a new sitecom 300n X2 (with 802.11n); after the change all my iOS devices (iphone4, ipod touch and ipad2) are not able anymore to automatically connect to my wifi network.
    The network is recognized and after inserting the password the devices connect perfectly to the network, but if I switch off the wifi interface and then i switch it on again the devices don't connect to the known network automatically, I have to tap on my network in the list to join it, even if password is not requested anymore (just once, when connecting for the first time). My Macbook and other Android devices are automatically connecting fine.
    I tried to forget the network and reconnect to it, I did a reset of the network stack under Settings->General->Reset, I did a device reset but nothing worked.
    I even tried to limit channel bandwidth of the router to 20 Mhz (suggestion found in a forum) but no success, and I also changed the wifi channel to avoid interference, but again no success.
    Any help will be really appreciated.
    Thanks a lot and regards.

    Hi there.
    Just changed my old wifi router belkin 54g with a new sitecom 300n X2 (with 802.11n); after the change all my iOS devices (iphone4, ipod touch and ipad2) are not able anymore to automatically connect to my wifi network.
    The network is recognized and after inserting the password the devices connect perfectly to the network, but if I switch off the wifi interface and then i switch it on again the devices don't connect to the known network automatically, I have to tap on my network in the list to join it, even if password is not requested anymore (just once, when connecting for the first time). My Macbook and other Android devices are automatically connecting fine.
    I tried to forget the network and reconnect to it, I did a reset of the network stack under Settings->General->Reset, I did a device reset but nothing worked.
    I even tried to limit channel bandwidth of the router to 20 Mhz (suggestion found in a forum) but no success, and I also changed the wifi channel to avoid interference, but again no success.
    Any help will be really appreciated.
    Thanks a lot and regards.

  • How many devices can I connect over USB to Configurator simultaneously

    Hi,
    I am looking for confirmation (preferably from Apple!) as to how many iOS devices can be connected via USB to Configurator simultaneously?
    There is one document from Apple which states 30 devices is the limit but we use carts with many more than this which Configurator appears to handle fine. You can also buy carts which accept more than 30 devices from the Apple Education Store.
    What I really need is an official document stating the limit or some feedback from you guys on your experiences with Configurator and high numbers of devices!
    Any help would, of course, be appreciated
    Thanks.

    Depends on your USB hardware....I have had two Bretford 30 unit carts running and while slow will work...Actually in our last deployment I went back to one MacBook Air AC station per 30 cart (4-5 carts per building) as the timing worked out better with temp workers and workflow....

  • HT201210 you are running the latest version of iTunes, have no other USB devices attached, have no security software installed, and are directly connected to your ISP source, simply restarting the computer and the iOS device can clear up certain issues th

    you are running the latest version of iTunes, have no other USB devices attached, have no security software installed, and are directly connected to your ISP source, simply restarting the computer and the iOS device can clear up certain issues that could prevent you from restoring. After restarting the computer and iOS device, attempt to restore again.

    How big is your library?  I would recommend the following troubleshooting steps:
    - Backup your library.  Always a good idea before messing with things.  
    - Create a new library.   Refer to this article for details:  http://support.apple.com/kb/HT1589.  This won't delete your old library, you're just creating a new empty one.  Also refer to this article to get back to your old library later.
    - Add a few albums into this new library.  Not everything, just a small sampling, as a test.
    - Activate Match on this new library.  You shouldn't have to re-pay, it should just say "Add Computer" or similar.
    - At this point, Match should run again. With just a few albums it should complete in just a few minutes.
    If iTunes doesn't crash at this point, then likely there's something about your original library that Match doesn't like - what that is I don't know, but at least you'll know it's not your PC.   If iTunes still crashes, then if could be a number of other things, but probably not your library.   My next suggestion (if you haven't already done this) is to uninstall / reinstall iTunes.   If that doesn't work, then my next ideas you won't like.   

  • I can connect to internet with my MBP through Airport Extreme, but my iOS devices can't. Please help.

    I can connect to internet with my MBP through Airport Extreme, but my iOS devices can't. Please help.

    GerleMan, Welcome to the discussion area!
    There are two probably causes:
    Your ISP is blocking the port used by Entourage to send mail and the ISP used by the other wireless networks is not.
    OR
    Your ISP doesn't like OS X's default MTU seting of 1500. If this were the case it should also affect any large file transfers you try to make from your Mac to the Internet.

  • "another device is using the same ip address.." - iOS devices won't connect to AEBS wifi.

    I've got a Motorola modem/gateway - 3360 from WalMart.  I have the AEBS working in bridge mode connecting my iMac & Printer fine, but my iOS devices won't connect. 
    While troubleshooting & trying all types of settings, I was able to get EITHER the iMac or the iOS devices connected to internet, but not both at same time.
    Then I noticed I am getting "another device is using the same ip address.." message.
    I have changed the AEBS ip address & had been able to get either the iMac or iOS devices working depending on which ip address I use. 
    BUT now, all my iOS devices dont connect to the internet regardless of the ip address of the AEBS.
    All my iOS devices see the network, and accept the network password, but they do not connect to internet, circle just keeps spinning...
    Any assistance is GREATLY appreciated.
    Thanks for any assistance,
    Dave

    It looks like may have to go back to square one and delete my network & set it up from scratch if I don't figure it out.
    If you do go this route, I would like to make a suggestion for your consideration, and that is to assign static IP addresses to devices that are "permanent" on your network or ones you want to make sure can be reachable at all times. These (again) would be servers, routers, wireless access points, network printers/scanners, NAS devices, etc.
    I would recommend the following IP addressing scheme as a baseline and you are certainly free to deviate in any way you see fit to meet your networking requirements:
    Reduce the number of IP handed out by DHCP. By default, most routers will provide 100-200 private IP addresses within their DHCP leasing scope. The AirPort, by default, assigns 10.0.1.2 thru 10.0.1.200 via DHCP. Your Motorola may assign 192.168.0.2 thru 192.168.0.150. Either way, I would reduce this to no more than fifty (50) total which should provide you with plenty of addresses even if you are hosting gaming convention at your home.
    I use the following IP address scheme for the "permanent" network clients:
    Network Printers: 10.0.1.200 - 209
    NAS Devices: 10.0.1.210 - 219
    Wireless Access Points or routers reconfigured as bridges: 10.0.1.220 - 229
    Servers: 10.0.1.230 - 239
    With the "permanent" devices pre-assigned with static Private IP address that are outside of the DHCP range, you shouldn't ever get an IP address conflict again.

  • Hi, I want to sync my Ipad to my computer to copy some photos from my Ipad, but it doesn't appear in my windows and it says my MTB USB Device can't connect, but it appears on my ITunes. How to configure it?

    I want to copy my photo from my Ipad to my computer, but it says that MTB USB device can't connect to my computer, but it can connect to my Itunes. Is there something that can be done?

    Hello Kvhviali,
    The following article provides some useful information and tips that can help get your iPad's photos and videos imported.
    iOS: Unable to import photos to computer
    http://support.apple.com/kb/TS3195
    Cheers,
    Allen

  • Can't connect wifi after install iOS 6, Can't connect wifi after install iOS 6

    Can't connect wifi after install iOS 6, Can't connect wifi after install iOS 6

    Can't connect wifi after install iOS 6, Can't connect wifi after install iOS 6

  • With itunes match live on my iOS devices, can I now remove all local music files from my PC to free up space?  There's no need to keep it if it will always be in the cloud.  Right?

    With itunes match live on my iOS devices, can I now remove all local music files from my PC to free up space?  There's no need to keep it if it will always be in the cloud.  Right?

    With itunes match live on my iOS devices, can I now remove all local music files from my PC to free up space?  There's no need to keep it if it will always be in the cloud.  Right?

  • On How many computers and iOS devices can I download creative cloud app?

    On How many computers and iOS devices can I download creative cloud app?
    so far it is on an iMac, an macbook pro, an iPhone , and iPad.    now it won't download onto a macbook air.

    Hi,
    see >>> http://helpx.adobe.com/creative-cloud/help/install-apps.html here >>> How many computers can I install on
    I quote: You may install software on up to two computers. These two computers can be Windows, Mac OS, or one each.
    If you install on a third computer, it will request you to de-activate on the other two computers. You can then reactivate one of the previous two computers, and use Creative Cloud apps on it.
    Hans-Günter

  • How many wireless devices can be connected at once to an airport extreme?

    How many wireless devices can be connected to an airport extreem at one time? I have 4 iphones and 2 ipads, a goolge chrome and 4 wired devices.

    Any AirPort Extreme produced since 2008 will support up to 50 wireless devices and 150+ wired devices simultaneously, so this should accommodate most users in most homes.

  • How many BLE device can be connected at once?

    Hi, is anyone having idea how many pcs of bluetooth low enegry device can be connected at once with iphone?

    You can only connect to one device of each type at a time. I regularly have my iPad connected to a BT keyboard and BT speakers at the same time. I could not, however, pair it to two different BT speakers. My phone is generally connected to multiple things as well (Pebble watch, Jawbone UP and speakers or a headset).
    I have about a dozen things paired at any given time.

  • How many devices can I connect to my iPhone hot spot?

    how many devices can I connect to my iPhone hot spot?

    Thank you.  I guess I don't need an additional hot spot device.  Thanks.

  • IPhone 4S with iOS 6 can't connect to open Wi-Fi network on HP/H3C WX5004 controller

    After upgrading from iOS 5.1.1 to iOS 6, iPhone 4S devices can no longer connect to an open wi-fi network on our campus.
    We have a controller based WLAN from HP/H3C managed by a WX5004 controller with AP models WA2620-AGN and WA2620E-AGN.
    Symptom: In the Wi-Fi dialog on the iPhone, out open campus network with SSID "CampusUniPassau" is displayed. After tapping this SSID, the iPhone tries to connect for a few seconds and then displays the error message 'Unable to join the network "CampusUniPassau'.
    Our WLAN controller logs the following errors:
    *Sep 21 08:40:46:336 2012 ac1 WMAC/7/ERROR : Invalid Extended Capabilities IE length (4).
    *Sep 21 08:40:46:336 2012 ac1 WMAC/7/ERROR :  Error while processing information elements
    #Sep 21 08:40:46:652 2012 ac1 WMAC/4/Station Association Fail: Station Assoc Fail:1.3.6.1.4.1.2011.10.2.75.3.2.0.4<h3cDot11StationAssocFailTrap> StaMac1:68:A8:6D:87:XX:XX StaMac2:68:A8:6D:87:XX:XX StaMac3:68:A8:6D:87:XX:XX Radioid:2 SSIDName:CampusUniPassau Cause:1 Desc:Unknown Failure APID:210235A42MB102000054
    With iOS 5.1.1, all worked well, so this should be an iOS 6 bug. Are there any workarounds until Apple releases a bug fix?
    Thanks in advance for any advice,
       Christian

    HI,
    i am affected by this problem myself. We are also using the H3C WX5004 with WA2620AGN accesspoints.
    Today I got update from H3C and got a new firmware to download.
    HEre is the description:
    The issue of the extended capabilities should be address in 5.20R2308P07  ftp  link below for the WX5004
    The issue was as described below :
    (1)           R2308P06 does not support Extended Capabilities (IE) which is contained in association request from the IPAD 3 IOS6, as below. This has been fixed by  the R2308P07 code.
    Regards
    Florian

  • HT204378 2 iOS8.1.1 devices can't connect via BT "Using Keynote Remote with Bluetooth" - HT6112

    I'm unable to get to iOS devices to connect via Bluetooth for Keynote control.  It's described above under the heading "Using Keynote Remote with Bluetooth".  Am I missing something?  I see the article mentions iOS8 so I know it's been updated recently.   I also see that this hasn't worked in the past.  Curious that the articles suggests it can be done now.
    I have 3 iOS devices all 8.1.1.
    iPhone 5
    iPhone 5s
    iPad 3rd Gen
    Thanks,
    Russell

    Just talked to Bose and learned the solution.
    Reset the speaker ....hold down the bluetooth button until you hear a tone. Delete the Bose in the Bluetooth Device directory on the iPad. When it is automatically rediscovered it will connect.
    Worked for me .....

Maybe you are looking for

  • Using an asset as a button

    Hey guys, I have a question about buttons, and using an asset under the "style" tab of the inspector. The file I want to use for a rollover is too complicated for an overlay, but looks fine when I add it as an asset to the button. The only problem is

  • Closed last Monday....all moved in!!!

    After three years of working hard, cleaning up report, being responsible with spending, on time payments, and a little bit of patience, I just closed on my first house. Conventional mortgage with a good interest rate and a fast closing.  The first we

  • JDBC to Idoc mapping - create multiple Idocs from 1 JDBC input

    I am importing data using JDBC and I want to put the data in an IDoc on a SAP system.  my data is about 100,000 rows, but my Idoc (ZIDOC) is defined as 1-35,000 for the segments.  I have followed Ossnote 814393, and also set up my Interface Mapping t

  • Not able to access ports through firewall

    I'm setting up our new server, and we want to run a Quark license server through port 1028. In the Server Admin, under Firewall->Services->Settings, I set up a service for the license server on port 1028 using TCP and UDP protocols. It's allowed for

  • Photoshop Help | Copy CSS from layers | Creative Cloud

    This question was posted in response to the following article: http://helpx.adobe.com/photoshop/using/copy-css-shape-or-text.html