IOS for MPLS on 1800 & 2600 series router

Hi,
What IOS version to be on 1800 & 2600 series routers to support MPLS

For MPLS Support on 1800 & 2600 Series you need IOS Release 12.3(14)*T or later.
Cisco IOS Release 12.3(14)YT on 1800 Series ISR
http://www.cisco.com/en/US/prod/collateral/routers/ps5853/prod_bulletin0900aecd802d0c05.html
Cisco IOS Software Release 12.3T Features
http://www.cisco.com/en/US/products/sw/secursw/ps5318/prod_bulletin09186a00801abfda.html

Similar Messages

  • Setting up a dsl as failover on 2600 series router

    I need to setup a failover line. the primary line is a T1 which is connected to serial interface. the secondary line is install to the FE0/1 of a 2600 series router. when i configure the nat pool IPOOL i get a error message saying that dynamic maping in use i need to have a sample config to complete this

    Hii,
    the msg comes up in there at nat sessions moving on...so u need to clear the ip translations and try executing the command.. if still msg crops.then u might hv to shut the local inside nat interface for a while ..
    pls do rate the post.

  • Cisco 2600 series router and cable modems

    Hi everyone, I am just about to get started preparing for my CCNA... I am looking to pick up some used Cisco 2600 series routers to set up a home lab. I am wondering if it is possible to connect a cable modem directly to a 2600 series router? If so, do I need a certain type of WIC? I want to go from my cable modem, to a router, to my switch. Thanks in advance!

    Hi,
    Yes you can, using the Ethernet port on the cable modem, you can connect the cable modem to the router 2600, and the 2600 comes with builtin ethernet or fastethernet (according to your platform).
    HTH,
    Mohammed Mahmoud.

  • 3640 IOS for MPLS

    Can anyone advise about 3640 IOS version using for MPLS.I have 3640 router with 16 flash and 64 memory and I need to run MPLS with all LDP features.Which IOS I can use.

    To run MPLS LDP and couple of more MPLS and VPN features only feature set available with 64/16 Dram/Flash for a 3640 is 12.3 with Telco Feature Set.
    HTH-Cheers,
    Swaroop

  • Reset 2600 series - no console connection

    I used this article to reset a 2600 Series router/voice gateway to it's default settings but it's not connection to my console connection after the reload....
    http://www.cisco.com/en/US/products/sw/iosswrel/ps5187/products_tech_note09186a00802017a1.shtml
    Any suggestions for how I can get in there again?

    you should be set for 9600 8 none 1, and flow control set to off.
    HTH,
    Steve
    Please remember to rate useful posts, and mark questions as answered

  • Understanding OSPF For MPLS Superbackbone.

    LSA1 is Router LSA And LSA2 is Network LSA.What is the difference between them?In which direction are they propogated?I need to understand it neatly as I am studying it for MPLS Superbackbone .

    In short, the router LSA is generated by all routers and describe all the connected interfaces on that router.
    The network LSA is generated by the Designated Router (DR) only and describe all the routers connected to the broadcast or NBMA network for which this router is the DR.
    If you need more information on what the LSA are for and the details of OSPF in general, I would recommend you read RFC2328.
    Here's the link for it:
    http://www.ietf.org/rfc/rfc2328.txt?number=2328
    Hope this helps,

  • 1800 series router - MPLS - VoIP

    I have a customer who wants to implement a VoIP solution on an MPLS network. Will the 1800 series router work in this environment or would they need a different router? If not what would be the minimum router they would need?
    Thanks for the help.

    Cisco 2800 is the minimum. Check this out
    http://www.cisco.com/en/US/products/ps5854/index.html (click on voice for more information)
    The model will depend on how my IP phones who are looking at and SRST support and things like that. If the number of users is more than 250+ you will have to go with 3845 considering growth.
    HTH

  • IOs for cisco 1900 series router

    Hi,
    Kindly provide me the IOS version (cisco 1900 router) which can fix the below listed Bugs,
    Cisco IOS TCP Listener Crafted Packets Remote DoS (CSCek37177)
    Cisco Multiple Devices Crafted IP Option Remote Code Execution (CSCeh52410)
    Cisco IOS System Timers Remote Overflow (CSCei61732)
    Cisco IOS Secure Shell Server TACACS+ Multiple DoS (CSCed65778, CSCed65285)
    Cisco IOS IKE XAUTH ISAKMP IPSec SA Establish Authentication Bypass(CSCeg00277)
    Cisco IOS Telnet Service DoS (CSCef46191)
    Cisco IOS H.323 Protocol Implementation Flaws Cisco IOS Malformed IPv4 Packet Remote DoS Cisco SSH2 Server/Client Malformed Packet Remote DoS (CSCdz60229, CSCdy87221, CSCdu75477)
    Cisco IOS SSH Large Packet CPU Consumption DoS (CSCdw33027) Cisco SIP Crafted INVITE Message Handling DoS (CSCdz39284, CSCdz41124) Cisco IOS Data-link Switching (DLSw) Capabilities Exchange Remote DoS (CSCsf28840)
    Cisco IOS AAA RADIUS Long Username Authentication Bypass (CSCee45312)
    Cisco IOS TCLSH AAA Command Authorization Bypass (CSCeh73049)
    Cisco IOS MMP Stack Group Bidding Protocol (SGBP) Crafted UDP Packet Remote DoS (CSCsb11124)
    Cisco IOS IPv6 Packet Processing Arbitrary Code Execution (CSCef68324)
    Cisco IOS Malformed BGP Packet Processing Remote DoS (CSCee67450)
    Cisco IOS Multi Protocol Label Switching (MPLS) Packet Remote DoS (CSCeb56909)
    Cisco IOS IPv6 Packet Processing Remote DoS (CSCed40933)
    Cisco IOS SCCP Control Protocol Malformed Message DoS (CSCee08584)
    Cisco IOS OSPF Packet Handling DoS (CSCec16481) Cisco IOS ARP Table Overwrite DoS (CSCdu81936)
    Regards,
    Bala

    Hi,
    The Current running IOS version is 12.2(4)T7. I tried through bug toolkit. but i couldn't able to consolidate the IOS to fix these bugs.
    Regards,
    A.Bala
    leolaohoo wrote at Tue Jan 25 02:20:52 GMT+05:30 2011:
    >Balakrishnan Appavu,
    >
    >A new message was posted in the Discussion thread "IOs for cisco 1900 series router":
    >
    >https://supportforums.cisco.com/message/3277195#3277195
    >
    >Author : leolaohoo
    >Profile : https://supportforums.cisco.com/people/leolaohoo
    >
    >Message:

  • Cisco 2500 & 2600 support for MPLS ???

    Can Cisco Router 2500 & 2600 Series provide provide MPLS switching?

    2600 is fine for lab use....
    milt-vpn-1>sh ver
    Cisco Internetwork Operating System Software
    IOS (tm) C2600 Software (C2600-J1S3-M), Version 12.3(1), RELEASE SOFTWARE (fc3)
    Copyright (c) 1986-2003 by cisco Systems, Inc.
    Compiled Thu 15-May-03 13:12 by dchih
    Image text-base: 0x80008098, data-base: 0x819BC684
    ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
    milt-vpn-1 uptime is 1 week, 6 days, 21 hours, 12 minutes
    System returned to ROM by reload
    System image file is "flash:c2600-j1s3-mz.123-1.bin"
    cisco 2611 (MPC860) processor (revision 0x202) with 59392K/6144K bytes of memory
    Processor board ID JAB0321051M (1822838117)
    M860 processor: part number 0, mask 49
    Bridging software.
    X.25 software, Version 3.0.0.
    TN3270 Emulation software.
    2 Ethernet/IEEE 802.3 interface(s)
    1 Serial network interface(s)
    2 Serial(sync/async) network interface(s)
    32K bytes of non-volatile configuration memory.
    16384K bytes of processor board System flash (Read/Write)
    Configuration register is 0x2102

  • IOS with MPLS for 2610XM ?

    There is no image with mpls that I can find, the lowest router is the 2651xm.
    However for my home lab I have 2610XM maxed out with 256meg mem and 48meg flash.
    Is there any IOS I can run that will allow me to configure MPLS VPN ?
    Thanks

    Hi, dtushing
    Please ignore my first post. There is a typo. The letter "i" and "j" look so simalar that I made a mistake when I used "cut&paste", I cut the wrong one.
    c2600-ik9s-mz-123-10b.bin is an IP PLUS feature set. It doesn't support MPLS.
    c2600-jk9s-mz-123-10f.bin is an ENTERPRISE PLUS feature set. It does support MPLS. As far as I tested on my router, it can support most of the features on topics like LDP, MPLS VPN, and MPLS TE.
    The Feature Navigator is a helpful tool but not for MPLS. It is not that accurate to find MPLS-related features on 2600 platform like it does on other features.
    As for the file, go to the Google and type the image name in the serach box and see what you can find there.
    HTH
    SSLIN

  • IOS for 2801 having support for MPLS

    Assalam o Alaikum,
    Is there any IOS for 2801 router which has the support for MPLS?

    Alaikum Al Salam,
    Please use Cisco Feature Navigator to find information about Cisco IOS software images and the supported features for your platform(s) :
    http://tools.cisco.com/ITDIT/CFN/jsp/index.jsp
    Search by feature and choose MPLS, and then choose Cisco 2801 as the platform, you'll get a list of the IOSs that support MPLS on your platform, and please always check the required DRAM and Flash.
    BR,
    Mohammed Mahmoud.

  • Selecting appropriate Router & IOS for Gatekeeper

    Hi All,
    I managing the Video conference setup but I am struggling to find a appropriate IOS for Gatekeeper
    I need some suggestion for selecting router series (Is 2620XM is ok?) and also the appropriate IOS?
    Gateway is Tandberg
    Planning for 8 video conference (8x256)

    This URL should help you:
    http://www.cisco.com/en/US/products/hw/routers/ps259/index.html
    http://www.cisco.com/en/US/products/sw/voicesw/index.html

  • After updating my iPad 2 to iOS 6, I cannot connect to my router.  I have turned the router off, left off for a considerable time, turned the iPad off and on, reset the network settings, nothing works.  Any other suggestions?

    After updating my iPad 2 to iOS 6, I cannot connect to my router.  I have turned the router off, left off for a considerable time, turned the iPad off and on, reset the network settings, nothing works.  Any other suggestions?  It is obvious many others are having similar problems, so the iOS 6 looks like a loser.

    I have just upgraded from a 3 to a 4S and now I can't connect to my wifi. I've tried everything, resetting network settings, switching to boot, renewing lease, rebooting, turning off cellular data etc etc. nothing works!! Very frustrating!

  • Recomended ios for 1200 series?

    Any suggestions for most stable and bugfree ios to use on the AP1200 series?
    For me it looks like the 12.3(8)JEA3 should be ok after reading about caveats in the release notes. Only something about shared authentication in non-native vlans and two other minor things. Our setup has 8 ssids with 4 of them with wpa-psk authentication that works ok with this version.
    Its a little confusing wich version to choose with all that numbers and release dates.

    Only some versions can be upgraded:
    For all IOS-based 1200  series modular access point (1200/1220 Cisco IOS Software Upgrade, 1210  and 1230 AP) platforms, it depends on the radio:
    –if 802.11G, MP21G and MP31G are supported
    –if 802.11A, RM21A and RM22A are supported
    The 1200 series access points can be upgraded with any combination of supported radios: G only, A only, or both G and A.
    http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp157130

  • 3600 series router for VOIP

    i need to know will cisco 3600 series router support 4 to 6 E1 for voice over IP using ISDN or PRI singnaling if 2-Port E1 Multiflex Trunk Voice/WAN Interface Cards (VWICs)is used in three slots provided by 3600 routers

    For Cisco 3600 routers to support VOIP you need to have NM-HDA module to provide DSP support without which VOIP can not be handled on 3600 series routers.Maximum Number of NM-HDAs Allowed in 3640 routrer is 3 and 3660 router is 6.So you can use either 3640 or 3660.

Maybe you are looking for