IP address error

Just set up a new Airport Extreme to replace an old one.  Internet works fine on main Mac desktop but when I try to log on with another device I get an error message that states my IP address is being used by another user.  Any thoughts?

Thanks, this is what I found as well. There are several different ways to set up this modem. We will try the simplest.
First, please perform a Factory Default Reset to get the AirPort Extreme back to original new settings as follows:
Pull the power plug from the back of the AirPort Extreme (AEBS)
Wait a few minutes
Hold in the reset button and keep holding the reset button in for another 8-10 seconds while you simultaneously plug the power back in to the AEBS
Release the reset button after the hold button and allow 25-30 seconds for the AEBS to restart to a slow, blinking amber light
Connect the Ethernet cable from the modem to the WAN port (circle of dots icons) on the AEBS
On your Mac, open Macintosh HD > Applications > Utilities > AirPort Utility
Click Continue to follow the guided setup. You can use the same names and password that you used before or setup new items.
Page 1....enter a name for the AEBS and device password
Page 2....select "Create a wireless network"
Page 3....enter a name for the wireless network and password
Page 4....select the option to "Share a single IP address...."
Page 5.....Configure IPv4 Using DHCP. No other entries are needed
Page 6.....Review and update to save settings
If you see a message about "Double NAT", click Ignore
Allow 25-30 second for the AEBS to restart
Then power off the modem, AEBS, computers, etc
Wait a moment
Start the modem first and let it run a minute by itself
Start the AEBS and let it run a moment
Start other device the same way
You should now be able to connect the Mac to one of the LAN ports on the AEBS using an Ethernet connection or look for the name of the wireless network that you setup, enter the password and log on.

Similar Messages

  • Trying to purchase trial period in different email address - error message "Error in Your Order The account was registered for a different country. Please sign out and sign in using an existing account for this country. Ok"

    Trying to purchase trial period in different email address - error message "Error in Your Order The account was registered for a different country. Please sign out and sign in using an existing account for this country. Ok"@

    Hi boags2014,
    Please refer this link and know the work-arounds for the same:
    How do I complete a purchase when I get an incorrect "country" error?
    Regards,
    Anubha

  • 5.1.0 - Unknown address error 554-'5.7.1 Access denied'

    Hi
    Over the last 5 days I my users have been getting alot of undeliverable's on delivery notifications:
    Subject: Delivery Status Notification (Failure)
    From: "Mail Delivery System" <[email protected]>
    Date: Sat, March 14, 2009 08:33
    To: SRS0=YH6uMo=7N=mydomain.com=[email protected]
    The following message to <[email protected]> was undeliverable.
    The reason for the problem:
    5.1.0 - Unknown address error 554-'5.7.1 Access denied'
    The original email is gettting through, its just we get an undeliverable on the delivery notification. All users use BIS with various providers, Orange UK, Vodacom SA, Vodafone UK. All the undeliverable are to internal domains the problem doesn't seem to occur with external domains.
    Can anyone help me please ?
    Thanks
    Kev

    Hi
    Anyone able to help me please ?
    Kev

  • BAPI_PO_CREATE1 keep prompting address error

    Hi Experts,
    I called the BAPI_PO_CREATE1 to create PO, but it keep prompting for the error msg : Address doesn't exist  T001W1001.
    I have checked plant 1001 is existed in table T001W, as well as ADRC address table corresponding the the address number in T001W.
    Is there any other reason why BAPII keep prompting for this address error while the address data seems fine?
    Any help is greatly appreciated.
    Thanks.

    adas

  • Why am I suddenly receiving the message: 5.1.0 - Unknown address error 501-"5.1.8 Bad sender's system address" I am only getting it for Mozilla Thunderbird

    In the past three days, whenever I send a message, it does not go through. Instead, I get the message: 5.1.0 - Unknown address error 501- "5.1.8 Bad sender's system address". I tried downloading the newest version of Thunderbird but it did not work. I do not receive this message when using other software.

    I had the look that you suggested. As far as I can tell there are no problems with the user name. Maybe I should check with my email company, Cogeco?

  • Attempt to access invalid address error message

    What does this mean "Attempt to access invalid address" Happens when I try to open PS element 5. I uninstalled and reinstalled my PS element 5 but error message still appears when I try to open the PS sw.

    Hi Garry,
    Yes, I did download PSE 8 and it did work.  However, the trial period has ended.  I have uninstalled PSE 8.  I have also unistalled PSE 5 and then reloaded it.  Upon completeion of the PSE 5 load, I tried to open the PSE 5 and the invalid address error message continues to display.  I am very sad that I cant get PSE 5 to work.  Can you help with more things I can try?  Please let me know
    All the best
    David

  • Address error. CrystalEnterprise.Smtp: SMTP_E_MAILBOX_UNAVAILABLE_2(550)

    Hi,
    Due to problems with the Report Server, I had to reinstall the Crystal Reports Server XI.  I had copied previous job description into word before reinstalling.  When I was  rescheduling reports I keep getting address errors. 
    I noticed that the description is different compared to the previous installation.  In the previous installation, I had the description "Mail the instance to 'xxx#xxx.com.au', 'bbb#xxx.com.au' with a subject of '%SI_NAME%'.
    In the new installation, the description is  "Mail the instance to "[xxx#xxx.com.au, bbb#xxx.com.au]" with a subject of '%SI_NAME%'.  It seems that the new installation added square brackets around the emails I entered, which was "xxx#xxx.com.au; bbb#xxx.com.au" (without quotes).
    How can I get Crystal reports server to recognise the email properly?
    PS: the at symbol is replaced with "#" due to limitations of adding email addresses.
    regards
    Frank Neo

    Hi Kyle,
    I would suggest testing on the Job Server machine by using telnet to see if you can email externally from the command prompt.  Below is a link of how to use mailman:
    http://www.yuki-onna.co.uk/email/smtp.html
    Are you able to schedule the report externally without an attachment?  I would also suggest speaking to your Exchange Server administrator.  There may be logs or restrictions for outgoing emails set on the mail server.
    Regards,
    Wallie

  • Address error. CrystalEnterprise.Smtp: SMTP_E_MAILBOX_UNAVAILABLE(550)

    Hi,
    On a weekly basis we are emailing a file to Vendor. I have set this up to send automatically from the BOXI scheduler but every time we run it, it fails with an SMTP error which appears to suggest it cannot find the mailbox. Vendor assures me the email address is correct.
    Could you please let me know if you have any idea on the error.
    Error Details:
    Address error. CrystalEnterprise.Smtp: SMTP_E_MAILBOX_UNAVAILABLE_2(550)
    Many Thanks,
    Madhu

    Hi Madhu,
    Typicall this happens when there is either an invalid email address or the SMTP server can not be reached.
    There are a couple kbase articles on this issue you may want to check out:
    [http://technicalsupport.businessobjects.com/KanisaSupportSite/search.do?cmd=displayKC&docType=kc&externalId=5855111&sliceId=&dialogID=23752242]
    [http://technicalsupport.businessobjects.com/KanisaSupportSite/search.do?cmd=displayKC&docType=kc&externalId=1950840&sliceId=&dialogID=23752242]
    [http://technicalsupport.businessobjects.com/KanisaSupportSite/search.do?cmd=displayKC&docType=kc&externalId=http--supportbusinessobjectscom-communityCS-TechnicalPapersNoNav-ce10smtppdfasp&sliceId=&dialogID=23752277]
    Jason

  • AnyConnect client no assigned address error

    I am trying to set up the AnyConnect client (v2.4.0196) and when it tries to connect it fails with a no assigned address error. I look in the logs of the ASA and see a No IPv6 address available for SVC connection. IPv6 is disabled on the ASA.
    Does anyone know how to prevent the AnyConnect client from trying to get an IPv6 address?
    Thanks in advance...

    Note that 2.4 is still beta, 2.3.2016 is the latest supported release today.
    Having said that, I rather suspect an ASA issue than a client issue. Can you confirm whether or not an ipv4 address is assigned?
    I.e. is there something in the logs like:
    Oct 13 2009 09:05:55: %ASA-6-737026: IPAA: Client assigned 192.168.0.1 from local pool
    Oct 13 2009 09:05:55: %ASA-6-737006: IPAA: Local pool request succeeded for tunnel-group 'DefaultWEBVPNGroup'
    (note these are level 6 messages)

  • E-mail that received in outlook from the Notes address error code:0x80070005-00000000-00000000 occurs

    When reply to the e-mail that received in outlook from the Notes address, error with an error code：0x80070005-00000000-00000000
    occurs (please refer to attachment),
    and we could not send mail. (Error details: Your message did not reach to the intended recipients, below email could not be delivered, please inquire to Network manager) When Created new
    and sent, e-mail sent became possible. Also, there was no mistake of e-mail address.
    Is there an alternative that avoids the current problem?
    If I perform a new email, it is possible to send.

    Hi,
    Which type of email account are you using?
    Have you checked this issue from web access?
    If the email address is saved as a contact in your Outlook, please try to delete it and then try to reply to the email to test if the problem persists.
    If you are connected to an Exchange server, please have a look at this KB article and check if it helps:
    http://support.microsoft.com/kb/195671/en-us
    Best Regards,
    Steve Fan
    TechNet Community Support

  • Mail's behavior on encountering an address error in sending to a group

    I routinely send to a group of 100+ addees, broken into three sub-groups because of ISP (Comcast) anti-spam limits on the number of addees.
    Several times I have gotten the error message that something is wrong with an address and the post remains in the OutBox.
    I have found the error and corrected it but do not know if
    (a) the correctly addressed emails were sent and only the one with the error was held for correction and subsequent sending, or
    (b) only the one with the error was held and the others trashed, or
    (c) they were all held until the error was corrected and all were then sent, or
    (d) none of the above.
    I have some inkling that (b) is what happened but I can find no way to determine what Mail actually does upon encountering an address error or what I should do. The programmers must have devised a strategy and I'd appreciate knowing it.
    Can someone help me with the logic and what to do when such an error occurs?
    BTW, I am using Smart Groups and they seem to work flawlessly if I don't make an error in an address!
    Thanks in advance...
    Bill
    dual 2GHz G5 PowerMac   Mac OS X (10.4.7)   Plain vanilla computing..

    Ernie, David,
    Thank you for the info. I now know that a message addressed to a group is "all or nothing at all," i.e., if one address is incorrect (in my first case, a "." where an "@" should be) everything stops until the error is corrected and then all messages are sent.
    There was a second error of a nother nature in another group (about which I can't remember the details, but it was an obvious typo) that generated a different error message (I should have copied both!) and when I cleared it everything also seemed to be sent.
    It seems Mail is deliberately designed to be tolerant of us mortals, giving us a chance to correct a hitherto unknown error and then going about its business. Nice design.
    I'll let you know if I run into other problems. And you can be sure I'll be more careful when importing addresses into Mail.
    Thank you very much for your kind help.
    All the best,
    Bill

  • Holding down "shift" during startup causes an "address error" with a prompt

    while booting from a dedicated OS 9.2.2 drive,...
    holding down "shift" during startup causes an "address error" with a prompt to restart holding the shift button,...
    an ideas,....?
    it otherwise starts up fine normally,....
    with spacebar depressed everything good too,.... into extensions manager...
    but booting with extensions off causes that address error crash just before desktop is to appear,...
    hmmm,.... ideas,....?
    thanx

    Well, address error means it's getting an odd addy somehow, and if it's with Extensions off, then maybe a PRAM or NVRAM reset would cure it...
    Have you done a PRAM reset...
    http://docs.info.apple.com/article.html?artnum=2238

  • Why do I keep getting Java Script address error messages?

    I just installed FF on my Macbook, and am constantly getting java script address error messages popping up.

    Does the below article help resolve the messages?
    * [[Warning Unresponsive script - What it means and how to fix it]] < Click to see article

  • After Effects Invalid Table Address Error 83 :: 2

    So, when I want click on Effects -> Animation Presets -> Text -> and use the animations in there, I would have the error of After Effects Invalid Table Address Error 83 :: 2. I'm using Adobe After Effects 2014.2 Release Version 13.2.0.49
    Other of my adobe products are working fine, even media encoder and premiere pro.
    My computer is windows 8.1, 64 bit.

    Sounds like you have a corrupted font. Try changing the font in the Text Panel to something common like Arial before you add text. If that doesn't work examine your font list for some odd fonts.

  • Mail error 5.1.0 - Unknown address error 554-'5.7.1 user@rjh.school.nz : Recipient address rejected: Access denied'

    Cannot receive mail in.  Can send mail out.
    Result of postconf -n
    alias_maps = hash:/etc/aliases,hash:/var/mailman/data/aliases
    biff = no
    command_directory = /usr/sbin
    config_directory = /etc/postfix
    content_filter = smtp-amavis:[127.0.0.1]:10024
    daemon_directory = /usr/libexec/postfix
    debug_peer_level = 2
    enable_server_options = yes
    header_checks = pcre:/etc/postfix/custom_header_checks
    html_directory = /usr/share/doc/postfix/html
    inet_interfaces = all
    mail_owner = _postfix
    mailbox_size_limit = 0
    mailbox_transport = dovecot
    mailq_path = /usr/bin/mailq
    manpage_directory = /usr/share/man
    message_size_limit = 83886080
    mydestination = $myhostname, localhost.$mydomain, localhost, rutherfordint.co.nz, rjh.school.nz, hpcfootball.info
    mydomain = rjh.school.nz
    mydomain_fallback = localhost
    myhostname = mail.rjh.school.nz
    mynetworks = 127.0.0.0/8,rjh.school.nz,rutherfordint.co.nz
    newaliases_path = /usr/bin/newaliases
    owner_request_special = no
    queue_directory = /private/var/spool/postfix
    readme_directory = /usr/share/doc/postfix
    recipient_delimiter = +
    relayhost =
    sample_directory = /usr/share/doc/postfix/examples
    sendmail_path = /usr/sbin/sendmail
    setgid_group = _postdrop
    smtp_sasl_auth_enable = no
    smtp_sasl_password_maps =
    smtpd_client_restrictions = hash:/etc/postfix/smtpdreject cidr:/etc/postfix/smtpdreject.cidr permit_mynetworks permit_sasl_authenticated permit
    smtpd_enforce_tls = no
    smtpd_helo_required = yes
    smtpd_helo_restrictions = reject_invalid_helo_hostname reject_non_fqdn_helo_hostname
    smtpd_pw_server_security_options = cram-md5,login
    smtpd_recipient_restrictions = permit_sasl_authenticated permit_mynetworks  reject_unauth_destination check_policy_service unix:private/policy reject
    smtpd_sasl_auth_enable = yes
    smtpd_tls_CAfile = /etc/certificates/server.rutherfordint.co.nz.C3479A3DA932D042025B19ACAEA2F77EE5 C1AF86.chain.pem
    smtpd_tls_cert_file =
    smtpd_tls_exclude_ciphers = SSLv2, aNULL, ADH, eNULL
    smtpd_tls_key_file =
    smtpd_tls_loglevel = 0
    smtpd_use_pw_server = yes
    smtpd_use_tls = no
    tls_random_source = dev:/dev/urandom
    unknown_local_recipient_reject_code = 550
    virtual_alias_domains = $virtual_alias_maps hash:/etc/postfix/virtual_domains
    virtual_alias_maps = hash:/etc/postfix/virtual_users

    I'm getting the same errors and well having issues with virtual domains, even after I add user e-mails in INFO tab in workgroup manager.  
    : Recipient address rejected: User unknown in virtual alias table [RCPT_TO]

  • Hardware Address error/warning

    anyone ever see this during a setup?
    WARNING: Hardware address cc:cc:cc:dd:dd:dd trying to be our address 192.168.10.10
    I'm setting up a T2000 and going through newtwork setup, but on boot up I get that error/warning.
    any thoughts?

    That's a network configuration issue.
    A generic IP address conflict.
    As it states, there's another computer on your subnet that's already using that IP.
    A Google search with "hardware address trying to be " keywords gets you 4,180,000+ results on this issue.
    Pick a different IP for your new system,
    or find that other system and have it use a different IP.

Maybe you are looking for