IP invalid - DHCP option not working - Moden Motorola SB5120

Hi Apple friends,
My Airport is not being able to get the ip number from my Motorola modem SB5120, I know that the ip should be provided by my modem (DHCP server), but for any reason it is not working. The airport works without any problem if I connect it to my I-LINK router. Does anyone could help me with some information that could help me to solve this issue?

Williamfs wrote:
I turned the modem off for over than 6 hours and then tried to connect again, but the airport is still not being able to get an ip from the modem, should I call the ISP? Would you have any other information that could help me?
I'd verify that your AirPort unit is configured correctly. Launch AirPort Utility, double-click on the icon of your unit on the left to enter "Manual Configuration" mode, the select the "Internet" panel and the "Internet Connection" tab. You should see settings for "Connect Using" of "Ethernet" and for "Configure IPv4" of "Using "DHCP".
If that's all set correctly, then the next step should be to call your ISP. The question you need to ask them is whether they record the "MAC address" of your equipment and whether they need to change their settings if you replace the equipment directly connected to your modem. If so, the value they will need from you will be labeled "Ethernet ID" and will be on the outside (perhaps on the bottom) of your AirPort unit.

Similar Messages

WRE54G - DHCP Soundbridge not working

I am sure everyone has has had issues getting a WRE54G up and runing at home - not the easiest of products (when using the encryption option).
I have an Organce LiveBox ADSL/Wireless router (Sagem badged Orange) and needed the range extended to get my Soundbridge (Pinnacle badged Roku) working elsewhere in the house.
A couple of problems:
- DHCP does not work via the WRE54G. Solved this by setting a static IP address on the Soundbridge (you telnet to it on port 4444 and use the ipset command line utility)
- The Soundbridge can access Internet radio stations fine, but if connected via the WRE54G then it loses contact with the Firefly media server
- WindowsXP PnP "sees" the Soundbridge the "other side" of the the WRE54G but cannot access it when you double click on the icon. Not an issue as just using the static IP address in the browser gets the configuration screen
I guess that I had expected the WRE53G to act more like a repeater, but is appears to be working as a bridge and the bridging function is somewhat broken.
Anyone have any ideas / fixes for the product? This is highly infuriating.

Try a different wall plug and see if that makes any difference, try a different power cable of the same power specification or a universal power adapter(if possible)...Maybe the Power Adapter is faulty and the unit is still functional...

Wifi option not working in my i phone 4s ios 7.0.2, how to fix it

wifi option not working in my i phone 4s ios 7.0.2, how to fix it

Now my wifi is working but not showing the wifi logo on the top

Guest LAN and DHCP Options not passing through

Managed to get the Guest LAN up and running for wired clients and all's working well. Users are sat behind a proxy and if I force the use of a appropriate wpad file I can get the WLC auth to happen and then push off to the proxy.
I'm trying to use option 252 in DHCP to present the WPAD url. Only issue that happens is that while the DHCP server on the egress interface is handing out addresses to clients on the ingress interface correctly, the WLC doesn't appear to be handing through the option 252 I have set in DHCP. I've used network monitor to see what the dhcp request process is dishing out in terms of options, and all look good if I'm not behind the WLC.
Anyone know if theres a limitation on the WLC that prevents DHCP options being passed through to the guest LAN?
TIA

When configured as a DHCP server, some of the firewalls do not support DHCP requests from a relay agent. The WLC is a relay agent for the client. The firewall configured as a DHCP server ignores these requests. Clients must be directly connected to the firewall and cannot send requests through another relay agent or router. The firewall can work as a simple DHCP server for internal hosts that are directly connected to it. This allows the firewall to maintain its table based on the MAC addresses that are directly connected and that it can see. This is why an attempt to assign addresses from a DHCP relay are not available and the packets are discarded. PIX Firewall has this limitation.
For more information please refer to the link-http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008070ba8f.shtml

'Get All New Data Request by Request' option not working Between DSO n Cube

Hi BI's..
Could anyone please tell me why the option ' Get one Request only' and 'Get All New Data Request by Request' is not working in DTP between Standard DSO and InfoCube.
Scenario:
I have done the data load by Yearwise say FY 2000 to FY 2009 in Infopackage and load it to Write-optimised DSO (10 requests) and again load Request by request to Standard DSO and activate each request. I have selected the option in DTP's to 'Get All New Data Request by Request' and its working fine between WDSO and SDSO. But not working between Cube and SDSO. While Execute DTP its taking as a single request from SDSO to Cube.( 10 request to single request).
Regards,
Sari.

Hi,
How does your DTP setting looks like from below options ? It should be change log, assuming you are not deleting change log data.
Delta Init. Extraction from...
- Active Table (with archive)
- Active Table (without archive)
- Archive ( full extraction only)
- Change Log
Also if you want to enable deltas, please do not delete change log. That could create issue while further update from DSO.
Hope that helps.
Regards
Mr Kapadia
*Assigning points is the way to say thanks*

InfoPath 2013 - Rich Text box - Expand to show all text option not working

I have create an InfoPath form and created a view which will be used for printing. I have a rich text box in this print view and the scroll option for this rich text box is set to "Expand to show all text". However, it is not working and it doesn't
expand the size of the text box based on the content length.
same thing used to work in InfoPath 2010.
Any suggestions?
Thanks,
Neelesh

Hi Wendy,
Here are the steps I have used:
1. On default view added a rich text box.
2. Created another view called Print and mapped it to the same Field which I added to default view
3. Set the Wrap text and Expand to show all text on both the Rich Text Box Properties - in default view and in Print
view. Also set the height of the rich text box to auto.
4. Set the print views as the print view for default view
5. Deployed the form to SharePoint Form Library
6. Opened the form in browser
7. Entered the content in the rich text box in default view. It expands well if I have much content
8. Clicked on Print preview and that opens up the print preview and it shows the rich text box only one line in height and with scroll bar
I missed to mention that it is a web browser enabled form and I am using InfoPath 2013 and SP 2013.
It does work fine in InfoPath client.
Thanks.

Hierarchy Node Variable search (find) option not working

Hi Experts - I have created a hierarchy node varibale on a fixed hierarchy. When user run the report and click on hierarchy node variable selection option , A new window will pop up which has all the nodes.
As the list is quite big and has many levels , On the same pop up , we have find option , when we enter any node in the find box , its always give a ABAP Dump , It never works for me...
Is node find/search in not working in Bi 7.0 .
Thanks
R

Hi Rohan,
We can restrict the hierchey level at property of of the hiearchey enabled characteristic.
Hope this hels...let me know if u require any further info on this..
Best Regards,
Maruthi

Complaint - Netflix and Youtube (internet option) not working on Apple TV 2 - Please advise

Netflix and Youtube (internet option) is not working on Apple TV 2 I bought - please advise how to fix this. Please note this is not to do with signing in as the internet menu and option to sign in is not given at all on screen/within ATV2. The only menu options which appear on screen are "computer" and "settings" and nothing else.
I have read from some other posts this may be because of the country in which I am located (currently the UAE) - this of course is not an acceptable excuse and if the real reason I hope Apple will fix this immediately. From the box I bought the description on the reverse side of the packaging clearly states "Plays movies and TV shows from Netflix, live and archived games from MLB, NBA, and NHL, and videos from YouTube and Vimeo".
If it is a country specific/territory issue then the packaging must be changed for countries in which this does not work as this product is being missold to customers, especially as having the option to stream Netflix, YouTube and Vimeo is one of its unique selling points - without which I would not have bought it in the 1st place!
Currently very disappointed in Apple (normally a complete Apple fan!)
Any help appreciated (positive comments only thank you).

In reply to the comment "You seem to be saying that the box that you have is different in some way". I'm actually not saying that at all as I have no idea what your box says and therefore can't comment.
And unless you're on the packaging design or distribution teams it would be a giant leap to presume every single box around the world is the same based on the product being the same.
As a marketing person I know companies of all sizes and shapes tailor their products to cater for individual markets. E.g. coca cola cans have different designs based on distribution location and languages used in particular countries and even the product itself can differ, although this may not be the case with Apple of course.
I'm simply describing what is on my box and I don't neccessarily mean to be abrupt however I certainly wouldn't waste my time typing on this forum to say the box says something when it actually does not.
Let me know if you can postively affect the outcome of this problem/help in someway and I'll be sure to send the image.
Thanks.

"Restore last view settings when reopening documents" option not working with all documents

Said option (found under Edit/Preferences, category Documents), which works like an automatic bookmark in that it takes you back to the same place you were at when you last closed a document, is very useful, but apparently doesn't work with *all* documents.
- Does anyone know what determines whether a given document works with this option or not?
- Is this by design or a bug? A matter of PDF format version?
- Is there a way to work around the problem?
I've compared two documents, only one of which works with the option, to determine what the relevant difference may be, and found two suspects (under File/Properties): the PDF version (1.5 in the document that works, 1.4 in the one that doesn't), and 'Fast Web View' ('yes' in the document that works, 'no' in the one that doesn't).
Thanks,
Michael

This seems to be a problem with some PDF files.
Suggested workaround: If the PDF you have allows "Save As", then try save-as to a new file. The "Restore last view settings when reopening documents" option should then work as expected (in the new file).
(Original post: Restore last view setting not working in version XI)

Ribbon options not working for SharePoint Central Administration

Hi,
I am able to see the options on the Ribbon of Central Administration, but clicking on the options is not working.
Have tried, Starting the Central Admin with Admin account, Setting user account control to never notify, adding the site to the trusted sites, resynced the SP servers time etc.
But nothing helped.
The ribbon is not working only for the Central Administration, it is working for web applications created.
I could not create a new web application, create a new service application, could not select a webapplication or simply i cannot do any thing on Central Administration.
Need help on this, Thanks in advance.

Couple of things, you can check..
1) Run the Internet Explorer as Administrator and then open CA,
2) make sure your Admin account is in Local Admin group,
http://epmgelist.wordpress.com/2013/06/14/central-administration-greyed-out-ribbons-and-missing-functions/
Check if UAC is enable or disable?
Please remember to mark your question as answered &Vote helpful,if this solves/helps your problem. ****************************************************************************************** Thanks -WS MCITP(SharePoint 2010, 2013) Blog: http://wscheema.com/blog

.svgz web preview in save options not working

Hi there
I'm a longtime Photoshop / After Effects type with rather less experience in Illustrator, using a newly built PC system
I've just gone to save a diagram created in Illustrator as a .svgz in order to pass to the web guy, but wanted to preview it first, so hit the Web Preview button in the Save dialogue box.... and nothing happens. I have several browser windows opn - IE9 64bit, Chrome - but the svgz appears in none of them
I presumed maybe I need to link Illustrator to a particular web browser somehow, but can't seem to find reference to how to do this, if it is necessary...
How do I get the web preview to happen?
All help appreciated...
I'm using latest Illustrator in Win 7 64bit
jON

I'm using Illustrator CS5 on Win 7 64 bit, and I cannot get Web Preview to work when suning Export, and exporting a file to Flash swf with frames. I have IE set on the Save for Web option, but no such option exists in the Export dialogue box. This option worked fine for the teacher in the help video that shows how to animate a snowboarder graphic when exporting to svf, but I cannot find anything dealing with this in the forums. Are you aware of why this is not working and how to implement it?

Find Option not working in Defect Screen

Hi,
In QM I have more number of defect code groups in my system, during defect recording I m using Ctrl+F option to find the exact defect code. But this option was working fine in 4.6C but its not working in ECC 6.0. Is there any setting or how to solve this issue.
Right now we r upgrading our system from 4.6C to ECC 6.0.
Thanks in Advance,
Regards,
S.Babusingh

Hi Anil,
Thanks for information but the below mention note is not supported for ECC 6.0 with enhancement package 4.0.
So pls let me know anybody having any alternative soln.
Thanks in Advance
Thanks & Regards,
S.Babusingh

Why is the livechat option not working?

This has got to be the worst customer service I have ever experienced. I just want to talk to a real human being. My phone is currently not working, so calling is not an option. Everytime I go through the "get support" page it gives me three contact options, but will not let me click the livechat option. I am doing this during normal service hours, and it is not a holiday. I have been trying all day, so unless you are extremely busy that can't be it either. Please, just give me a link so I can talk to somebody! I don't want to waste more time on these forums. Thank you.

in general, adobe's pretty generous about that: things you create using adobe programs are yours to keep and/or sell even if they're created using adobe programs that are in trial use.
here are the specifics: Licenses and terms of use | Adobe

Check printing:Print immediately option not working in check printing

Hi,
In check printing program i have made some changes for sending data to 2nd page,when line items crosses more than 1 page.
In such cases print immediately option,selected on the screen of FCH7 is not working.Always i have to print from spool.
If data is limited to single page,then print immediately option is working fine.
Can you have some idea about this option to work correctly?
Thanks & Regards
Seshagiri.

Can u check out for the field TDIMMED field in output options.
I think U have to reset that flag .

DHCP *still* not working.

i posted some of the problems i was having in this post here :
http://discussions.apple.com/thread.jspa?messageID=5706025
after reinstalling 10.5 Server about half a dozen times... DHCP randomly started working just fine and has been working pretty well in the past month or so.
then i got some new computers recently.
none of them get a DHCP address. not a single one. they all get self-assigned numbers.
and the log is once again filled with the familiar :
Feb 11 12:52:33 dropbox bootpd[312]: DHCP DISCOVER [en0]: 1,0:1e:c2:b7:d9:e3 <Air23>
Feb 11 12:52:33 dropbox bootpd[312]: service time 0.000963 seconds
Feb 11 12:52:34 dropbox bootpd[312]: DHCP REQUEST [en1]: 1,0:1e:c2:b7:d9:e3 <Air23>
Feb 11 12:52:34 dropbox bootpd[312]: service time 0.002062 seconds
Feb 11 12:52:34 dropbox bootpd[312]: DHCP REQUEST [en0]: 1,0:1e:c2:b7:d9:e3 <Air23>
Feb 11 12:52:34 dropbox bootpd[312]: service time 0.001575 seconds
Feb 11 12:52:35 dropbox bootpd[312]: DHCP REQUEST [en1]: 1,0:1e:c2:b7:d9:e3 <Air23>
Feb 11 12:52:35 dropbox bootpd[312]: service time 0.001488 seconds
repeat non-stop and for every single new machine i got.
anyone have any ideas?
i tried recreating the subnet from scratch again... no change.
i tried adding the <replythresholdseconds> to 0 again... no change.
where or how is the server keeping track of the "old" machines being viable and able to get an IP vs. the "new" machines which refuse to work at all? there has to be something somewhere where it is keeping track of this.
i also tried converting an old machine that never was on DHCP to DHCP ... it also was unable to get an address.
manually-assigned out-of-range DHCP addresses seem to work fine on the new machines however. my DHCP goes from 192.168.3.2 -.127 ... and addresses manually entered at .200+ all give the machines a network connection. this is a temporary solution however.
any ideas?
thanks.
zeb.

at this point in time... yes. hundreds of times. just near the bottom of the .plist.
tried it in the upper section where the subnet info is as well... made no difference.
let me copy/paste my .plist in here...
<dict>
<key>NetBoot</key>
<dict/>
<key>Subnets</key>
<array>
<dict>
<key>allocate</key>
<true/>
<key>dhcpdomainname</key>
<string>arcus.org</string>
<key>dhcpdomain_nameserver</key>
<array>
<string>209.165.164.3</string>
<string>209.165.164.13</string>
</array>
<key>dhcpnb_over_tcpip_nodetype</key>
<string>1</string>
<key>dhcp_router</key>
<string>192.168.3.1</string>
<key>lease_max</key>
<integer>10800</integer>
<key>lease_min</key>
<integer>10800</integer>
<key>leasetimesecs</key>
<string>3600</string>
<key>name</key>
<string>192.168.3</string>
<key>net_address</key>
<string>192.168.3.0</string>
<key>net_mask</key>
<string>255.255.255.128</string>
<key>net_range</key>
<array>
<string>192.168.3.2</string>
<string>192.168.3.127</string>
</array>
<key>selectedportname</key>
<string>en1</string>
<key>uuid</key>
<string>A604DFA1-6F33-4B7D-8081-1197E1D51D44</string>
</dict>
</array>
<key>dhcp_enabled</key>
<true/>
<key>replythresholdseconds</key>
<integer>0</integer>
<key>timeDatabaseUpdated</key>
<string>2006-04-25 07:20:31 -0800</string>
<key>timeServiceStarted</key>
<string>2008-02-13 16:24:40 -0900</string>
</dict>
i clipped out the header and <plist> tags... they are still there in the real file.
thanks.

IP invalid - DHCP option not working - Moden Motorola SB5120

Similar Messages

Maybe you are looking for