IP-settings and keymap for guest

Hi,
I have a few questions about the configuration of a guest.
1: How should I set the IP-settings for the virtual NIC?
I used a free IP on my network, as the gateway I used the same gateway as the server and as the netmask ofcourse also the same netmask as the server. I can ping to other computers on my network, so it's working fine. But I can't surf on the Internet with the guest. Do I have to change the nameserver?
2: How can I change the keymap that is used on the guest?
During the installation of OEL5U1 I chose to work with the keymap: be-latin1. When I open the file /etc/sysconfig/keyboard, I can verify that this is the keymap being used on the guest. But still, when I type, it's still qwerty instead of azerty and I can't find several characters. Is it possible I have to change the keyboard layout on the OVM Console, on the plugin?
Thanks!

1: How should I set the IP-settings for the virtual NIC?
you may surf on internet using ip address directly? and do you need set http proxy in your environment?
2: How can I change the keymap that is used on the guest?
If you are using a keyboard with a layout other than US, the key mappings may not work properly in guest OS on the graphical console. (note:466564.1 Keyboard Mappings Does not Work Properly for Guest OS)

Similar Messages

I have just rented a film and clicked the menu button instead of pause. When I go back to the film to rent again it says I have already rented this go to settings and check for downloads. But there is no download option in settings?

I have just rented a film and clicked the menu button instead of pause. When I go back to the film to rent again it says I have already rented this go to settings and check for downloads. But there is no download option in settings?

It does... Apple TV has a problem with the assignment to the itunes account after updating. Restore to factory settings or unlog and news login to the itunes store helps to see the rented/downloaded film(s).

HT1657 I rented a movie and accidentally hit the menu button and now I can figure out how to go back and watch it . When I try to press rent again it says you have already downloaded this movie go to settings and check for downloads but I can find it.

I rented a movie and accidentally hit the menu button and now I can figure out how to go back and watch it . When I try to press rent again it says you have already downloaded this movie go to settings and check for downloads but I can find it download in settings.

I had the same issue with my apple tv 3rd generation. I rented Sinister and selected the "rent and watch now" option. Half way through the movie I accidentally pressed the menu button. When I looked for the rented movie on my apple tv I could not find it. Not even above the movie pannel where "purchased" and "top movies" comes up on the main menu. the apple tv suggests to go to settings>downloads but I don't have that option. I did go to settings> itunes store> check rentals but that didnt work either. It took too long to even check. Thank you because this SOLUTION worked great.
SOLUTION: How to reset apple tv 3 3rd generation to view rented movies:on the apple tv remote: press and hold "menu" to go to the main menu. Select SETTINGS> GENERAL >RESET >RESET ALL SETTINGS. After the apple tv resets, input all your information again and your rented movies should be visible when you cruise above the "movies" section. THANK YOU!!
Apple needs to solve this issue because honestly it took me 3 hours and a half to watch a movie that only lasted 2 BECAUSE I wast trying to solve the issue, reseting and all. blahh.

How to backup all database settings and data for SOA suite to file(s) ?

During the installation of the SOA Suite a couple of tables and schemas are created
in Oracle database through the irca.bat script.
Later the tables are filled with content by all the servers and services of the
SOA Suite.
How can I backup all these tables and SOA related stuff to one (or more)
files (for a possible later restore)?
This backup should contain only SOA Suite related tables and data.
Possible other tables (for other applications) should not be considered.
Is there a script (e.g. for sqlplus) or menu which does the
SOA database backup job for me ?
If there is no official backup script maybe someone in this forum
wrote a personal script.
Thank you
Peter

I am facing the same problem.
I have spend a few days to configure and train my Sony tablet to configure for all my remotes such as aircon and lighting. I did a backup using the Sony companion to my PC. When my tablet was faulty and serviced. But the backup did not recover the IR remote settings and codes which I programmed previously. I also tried your backup restore app but it also does not save the configuration.
It is VERY IMPORTANT for me to backup the settings.
Please provide the folders and path of where the IR REMOTE settings and personal configuration and codes trained were kept so that I could back them up. Are these path protected area that required rooted access?
Hope that Sony could update the app to include backup of new trained codes and settings and in the meantime to provide a procedure of how to backup the setting and trained IR codes with or without rooting the device.

Just purchased Airport Extreme ac and lost internet connection 3X. Reset to factory settings and worked for 2 days then lost connection and remedied by unplugging power supply. Anyone else having problems?

Just purchased Airport Extreme ac and lost internet connection 3X in less than one week. Fisrt time, reset to factory settings and fixed problem. Has occurred 2 additional times and connection re-established by unplugging AP extreme. Anyone else having these problems? Do I have a bad router? Thanks.

I definitely think this is a Mavericks issue. My iMac running Mavericks is the ONLY system in the house that drops the network randomly while all other systems never lose the network. No idea how to resolve this, but here is the workaround I'm posting:
I've had the 'network drop' issue with my Airport Extreme for the last 2 months. It reconnects when I pull the ethernet cable and plug it back in. I've tried downgrading the AE firmware, resetting to factory, etc. Nothing worked. I finally threw in the towel and created a script that monitors my network connectivity and restarts my interface if it senses it has dropped:
#!/bin/ksh
while true
do
yup=`ping -c1 -t2 www.google.com|grep from`
if [[ -n $yup ]]
     then echo "Internet is connected!"
else
        ifconfig en0 down; ifconfig en0 up
        echo "Down at `date +%m%d%Y%H%M%S`">>./dropped.out
fi
sleep 5
clear
done
I know its a workaround, but its saving me the headache of constantly pulling my cable and putting it back in!
Good luck!
-Mike Gray

My Ipad2 is turning off all Icloud settings and asking for password every minute

Hi,
My Ipad2 is turning off all my icloud settings by itself and asking for the password every minute. After about an hour it works again but only for a few days and starts turning off the settings again.
This started about 3 weeks ago an even when it starts working again for a few days there are still some photos and contacts missing. But on my IPhone and on icloud.com everything is fine.
Has anyone an idea what is happening?

Hi,
Thanks for the tip. I deleted the Account and at least everything is back on my ipad. But it was asking for the password a few times since then.
But if it stops turning off all my settings i could live with putting in the password every hour...
I will see if it stops deleting and turning off.

Settings and configuration for APO SNP?

Hi,
we want to use SNP in the future.
Which configuration must be done in the APO customizing?
Which data must be transferred from R/3 to APO?
Does anybody has a kind of check list for the necessary settings?
Thanks,
Michael

Ken,
Ever since SAP discontinued the SCM 5.0 Best Practices, I have never seen all the APO building blocks that actually still exist all stored in a single place by SAP. I have to hunt around to find them.
RDS solutions (which sometimes include APO Building blocks) can be downloaded at
https://websmp206.sap-ag.de/~form/handler?_APP=00200682500000001943&_EVENT=DISPHIER&HEADER=N&FUNCTIONBAR=N&EVENT=TREE&TMPL=INTRO_SWDC_IU_PSP&V=INST&TA=ACTUAL&
provided you have adequate authority. Most of the building blocks that can be downloaded at the above link have also been published "somewhere" in help.sap.com. Also, you occasionally see a non-RDS BB in help.sap.com. So, when I want to find APO building blocks, and I can't find them under RDS solutions, I go into Help.sap.com and start using the search feature (the "Global search" on the home page, not Trex search).
If in your travels you ever find a 'centralized' repository for all APO BB docs that is publicly available, please publish it in SCN, because I am sure that many SCN readers would find this info valuable.
Best Regards,
DB49

Best settings and Format for Motion Logo to FCP

I working on a project in FCP using video that is SD 16x9 anamorphic and was trying to import some logo's and lower thirds from Motion to this project. I was wondering what settings I should be using in Motion to maintain the correct pixel aspect and also keep the quality of the logo high. I have had problems recently with certain motion projects and the quality becoming very poor once in FCP.
Also, I believe I am supposed to use a square as pixel aspect with logo's in Motion, where should I adjust that setting, in Motion or FCP? Thanks,

27993buck wrote:
I working on a project in FCP using video that is SD 16x9 anamorphic and was trying to import some logo's and lower thirds from Motion to this project. I was wondering what settings I should be using in Motion to maintain the correct pixel aspect and also keep the quality of the logo high. I have had problems recently with certain motion projects and the quality becoming very poor once in FCP.
Also, I believe I am supposed to use a square as pixel aspect with logo's in Motion, where should I adjust that setting, in Motion or FCP? Thanks,
There is no apostrophe in the plural form of logo any more than in the plural of third.
The workflow for anamorphic is clearly explained in the Motion manual. Where you get your logo is another issue. Why your quality is reduced in FCP is anyone's guess (apostrophe for possessive) and you have not provided any information that will help us figure that out for you. Was it squished? Was it pixelated? Wrong color? Fuzzy? Incorrect alpha?
*Using Square or Nonsquare Pixels When Creating Graphics*
*When you’re preparing to import graphics into Motion, it’s important to be aware of the pixel aspect ratio you’re using and whether your project requires you to work with square or nonsquare pixels.*
*Use nonsquare pixels for standard definition projects in NTSC or PAL.*
*Use square pixels for high definition projects, as well as multimedia video that will be played back only on computers and doesn’t use any captured video footage.*
*Graphics created on a computer, whether scanned, painted, or rendered, look distorted on a video monitor unless you account for the different pixel aspect ratio. Fortunately, this is easy to do, since every nonsquare video frame size has an equivalent square frame size that you can use to create your graphics.*
bogiesan
Message was edited by: David Bogie Chq-1third grade typos

HT1657 watching a movie on Apple TV and it just stops in the middle of it. Try settings and check for rental and just get the spinning wheel for over 30 minutes.

Can't seem to finish a movie on AppleTV. It just stops in the middle of movie and returns to menu. Try to check for rentals under settings like it says to when we try and download movie again and all I get is a spinning wheel. At least the second this has happened in the middle of a movie. Beginning to think AppleTV is junk!

Hello Pauljfield,
You may want to report the issue you've had with your rental to the folks in our iTunes Store.
How to report an issue with your iTunes Store, App Store, Mac App Store, or iBooks Store purchase
http://support.apple.com/kb/HT1933
Cheers,
Allen

This is a hint to anyone who cannot find their airprint printer from their ipad: after 10 hours of trying everything imaginable, i can now print directly from my iPad by turning off the bluetooth in settings and waiting for 30 seconds. presto!

after spending a full day and a half trying everything imaginable, i finally found a way to get my ipad to find my new airprint capable printer. I could print from email or the cloud, but not directly from my ipad. After reading a discussion about bluetooth printers, i turned off bluetooth in settings, waited 30 seconds, and voila!! I was able to print directly from my ipad. Try it if you are having troubles

Greetings,
I've never seen this issue, and I handle many iPads, of all versions. WiFi issues are generally local to the WiFi router - they are not all of the same quality, range, immunity to interference, etc. You have distance, building construction, and the biggie - interference.
At home, I use Apple routers, and have no issues with any of my WiFi enabled devices, computers, mobile devices, etc - even the lowly PeeCees. I have locations where I have Juniper Networks, as well as Aruba, and a few Netgears - all of them work as they should.
The cheaper routers, Linksys, D-Link, Seimens home units, and many other no name devices have caused issues of various kinds, and even connectivity.
I have no idea what Starbucks uses, but I always have a good connection, and I go there nearly every morning and get some work done, as well as play.
You could try changing channels, 2.4 to 5 Gigs, changing locations of the router. I have had to do all of these at one time or another over the many years that I have been a Network Engineer.
Good Luck - Cheers,
M.

Oracle settings and configuration for PS

I am attempting to install PeopleSoft 9.0 CRM etc on an Oracle database. I have a new PC (IBM T41) 1 GB RAM 1.6MHZ CPU.
I have downloaded Oracle 10x, PS 9.0 apps, Tuxedo, BEA, IIS 6.0.
All, except PS has been installed successfully.
Question: What are the settings in Oracle that need to be configured in order to get PeopleSoft 9.0 running. [I am not a DBA and do not know the specifics to get Oracle configured properly]
Is there anyone out there who is able to guide me, either through documentation or a response to this post?
Charles Cohorst

Network configuration assistant may have created at least two out of the four listed files at your ORACLE_HOME/network/admin directory:
tnsnames.ora
sqlnet.ora
It can configure, if required the listener.ora and ldap.ora files. Same issue at your ORACLE_HOME. It is important to make sure those files are properly located, otherwise you won't be able to connect to your instance, and if required, your listener won't be properly configured.
If you want further details on how to configure these files and what the required entries mean, you may want to read the Configuration and Administration of Oracle Net Services reference manual: http://download-west.oracle.com/docs/cd/B19306_01/network.102/b14212/part2.htm#i436475
~ Madrid.

ISE and SMS in plain text for Guest Credntial notification

I have configured a SMS notification for the Guest Credential.
When the SMS gateway receive the message, it's discarded because it's not in plain text, it's contains some HTML tag.
We haven't the possibility on the SMS gateway to modify the received message.
On the ISE I seen that we can choose the email format only for the system alarm settings and no for SMS message.
Correct ?
It's possible to send the message in plain text !!!!
thank you

I think it only use HTML.
Step 6 Type the email body in the Layout text box. This contains the account login information for the guest user.
You can use HTML tags and special variables for formatting the language template for e-mail notification. The following is an example of the login information for the body of an email in an English language template:
Welcome to the Guest Portal, your username is %username% and password is %password%
Jatin Katyal
- Do rate helpful posts -

Using several Airport Extremes to create and extend corporate + guest wifi

hello all,
my office has purchased 6 airport extremes for our new office, AirPort Extreme 802.11ac (6th Generation), running version 7.73
the plan was to hard wire one extreme via the wan port and create both a corporate and guest network
then link to the others throughout the office by wirelessly extending to provide complete coverage
after moving around the location of one or two units my coverage is now complete across the office space
my setup is as follows:
my network is a windows active directory setup where one of my domain controllers is my DHCP server in the range 192.168.x.x
to enable the guest network on my extremes i need to have my first hard wired (wan port) extreme unit configured in DHCP mode
this airport extreme has pulled down an ip address from my windows server in the range 192.168.x.x
the extreme then uses its own dhcp range to provide connectivity to my clients, 172.16.x.x for corporate wifi and 10.0.x.x for guest wifi
my issue is
the dhcp range that the extreme uses for all my corporate wifi users is 172.16.x.x
i cannot access any servers on my windows network 192.168.x.x by drive maps/hostnames as they are challenged for authentication
I can only access by using ip addresses instead of hostnames
all of my shares and wired users are configured to use hostnames for file shares, printers etc on my servers
the first extreme gets its DNS info from my windows dhcp server correctly but these settings are not passed down to my wifi clients
is there a way to do this ?
I have tried using the 'domain name' field on the extreme dhcp config but this had made no difference
can anyone advise on this ?
do i need to use a different setup, maybe switch to wired config ?
what i'd like to have is the following:
2 wireless networks, one for corporate users and one for guests/visitors
my corporate users to have access to all my corporate servers as their permissions allow using hostnames for access
my guest users to have internet access only
my 6 access points to be connected to each other either wired or wirelessly to provide coverage throughout my office
i was told that the 6 airport extreme's would allow me to do this but now i'm not so sure
any help or suggestions would be gratefully accepted,
thanks

You are trying to use Apple domestic products in a business setup.. this is not what they were designed for.
Could you use 3 units to cover the offices.. please have a go as this simplifies things tremendously.. just use three units in bridge.. preferably all connected to your ethernet network and so operating as AP only.
If that works then use the other 3 units for your guest network.. these should then be placed on a different vlan via your main managed switch.. so they can get internet but have no connection at all to the office network.. but other ways around it could be found. As you have already discovered a simple double NAT might sufficiently block guest access.

HT1498 I tried to download a rented movie and it is only at 46%. When I try to view it there is an error message "error when loading" . I have gone to settings and checked my downloads it advises that there are no downloads. I have reset the resolution t

I am having problems renting a movie from the apple TV. The download only goes to 46%. I have tried changing the resolution to 720, I have gone to the settings and check for rentals it advises that there is no additional rentals found.
Any suggestions.

You have to go to SMTP settings for your email account and enter a password there. Sended and receiving are two different activities managed by 2 differet servers, and each may require a separate user ID and password.

What is the default username and password for administering my f4500 deskjet printer?

I need to administer my F4500 Deskjet through my web browser, but do not know the username and password. I presume there is a way to default the settings, but I need to know the defaults. Please provide the default username and password for web access.
Thanks.

The default username is Admin, but the password is blank by default. Somehow, a password was added at some point.
You can try going to the EWS and going to Settings and looking for a password reset option in the Administrator Settings section. If it is there, it will be the only way I know of clearing the password on this particular printer.
↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

IP-settings and keymap for guest

Similar Messages

Maybe you are looking for