IP SLA/Ethernet OAM on Cisco 7600 Series

Not sure if this is the appropriate place to post this discussion, so I appologize in advance if it is not.
I'm looking for iformation if CFM Local Maintenance End Point configured on Cisco 7606 router is able to respond to the Y.1731 Performance Monitoring (DMM/DMR ).
I know I can use IP SLA to configure Y.1731 PM measurements, but I just need a reflector that will answer for incoming DMM messages with DMRs.
Thanks

Similar Messages

Cisco 7600 Series Ethernet Services cards types & queue values

Hello,
There is different types for the Cisco 7600 Series Ethernet Services cards.
( More expensive cards with high queue values and less expensive cards with
low queue values.)
http://www.cisco.com/en/US/prod/collateral/routers/ps368/data_sheet_c78-549419.html
Hardware queues
ES Plus XT 40G line cards
• 128,000 ingress queues
• 256,000 egress queues
ES Plus XT 20G line cards
*• 64,000 ingress queues*
• 128,000 egress queues
Hierarchical QoS (H-QoS)
http://www.cisco.com/en/US/prod/collateral/routers/ps368/data_sheet_c78-570730.html
Hardware queues
Cisco 7600 Series ES Plus Transport 40G and 20G Line Cards
*Supporting up to 16 level 4 queues per physical port*
Hierarchical QoS (H-QoS)
Low queue cards have got only 4 queues per physical port. High queue cards
have got minimum 64.000 queue. This is very huge difference. In what kind
of scenario do we have to use the High queue cards ? Could you give some
examples please ? Kind Regards.
Burak

HI Burak,
Each time you configure a class with bandwidth allocation or shaping,.. a queue will be used so if you use such card to provide QoS for a lot of subscribers sharing the same interface, you will need a lot of them !!
HTH
Laurent.

Cisco 7600 Series (7603) Router Information

Hello,
Does anyone have a link or reference to a good description of the Cisco 7600 boot process and various memory heirarchy functions? I'm looking for information on what should be in NVRAM, FLASH, SUP-BOOTFLASH etc. Thank you.

You can find all the 7600 series router info here.
http://www.cisco.com/en/US/products/hw/routers/ps368/products_data_sheet0900aecd801c5cab.html
http://www.cisco.com/en/US/products/hw/routers/ps368/prod_literature.html
HTH,
Sundar

Cisco 7600 Series can't back up it's config using Ciscoworks

We have a problem with Ciscoworks. Our client's Cisco 7600 can't back up it's configuration with Ciscoworks, while the rest of the devices can. They are all enrolled and discovered in the Ciscoworks of our client. Do you have any idea how to troubleshoot this? Thanks!

Have you partitioned the drive and formatted it Mac OS Extended (Journaled?) If not, try that and see if it helps:
Extended Hard Drive Preparation
1. Boot from your OS X Installer Disk. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger.)
2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. SMART info will not be reported on external drives. Otherwise, click on the Partition tab in the DU main window.
3. Click on the Options button, set the partition scheme to GUID then click on the OK button. Set the number of partitions from the dropdown menu (use 1 partition unless you wish to make more.) Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the volume(s) mount on the Desktop.
4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
5. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, check the button for Zero Data and click on OK to return to the Erase window.
6. Click on the Erase button. The format process will take 30 minutes to an hour or more depending upon the drive size.
Steps 4-6 are optional but should be used on a drive that has never been formatted before, if the format type is not Mac OS Extended, if the partition scheme has been changed, or if a different operating system (not OS X) has been installed on the drive.

Ethernet over Public link with Cisco 65XX Series

We are transferring some equipment from one datacenter to another and we do not have private line connectivity between them at the current time.
We are hoping to be able to temporarily be able to establish some type of Layer2 connectivity between the facilities to help allow us to spread out the migration into 2 events. We have Cisco 65XX series switches at the core at both facilities and I am wondering what we might be able to use to make this happen?
EoMPLS is out as we have to be able to extend the layer2 functionality across carrier networks and L2TPv3 is not supported on Cisco 65XX from what I have read / checked on our switches (if there is an IOS version that does support it, please let me know).
I have read a bit about VPLS over GRE but I am not clear on the configuration and/or if it supported as it references MPLS at various points within the documentation that I have read.
Any guidance would be appreciated.

I've absolutely no idea if this would help in your case.
But anyway, I think 6500 handles DMVPN. May be MPLS over DMVPN would be a solution?
https://sites.google.com/site/amitsciscozone/home/important-tips/traffic-engineering/p2mp-mpls-te-over-dmvpn
http://networkknerd.blogspot.be/2014/08/dmvpn-mpls-over-dmvpn-oh-yeah.html
HTH

Trying to Download a Software Image to Cisco 2800 series router through TFTP Using the tftpdnld ROMmon Command

Trying to Download a Software Image to Cisco 2800 series router through TFTP Using the tftpdnld ROMmon Command
and I am getting an Error , I cant figure out what I am doing wrong. I have also pasted my display down here can someone help me out, thanks in advance, I am still new to this utility.
My questions are How do you direct this utility to point to the desktop or the TFTP folder
does FE_PORT: Fast Ethernet 0 imply or point to Fa0/0 on my router
My router is suppose to have 10.0.0.3 255.0.0.0
Gateway of 10.0.0.1 255.0.0.0
My TFTP Server 10.0.0.2 255.0.0.0
How do I get the MAC address of the Router or the TFTP Server and which one is required?
my Ethernet port is 100Mb/Sec I cant tell whether it is full duplex or not so How do i set this FE_SPEED_MODE: Auto???
=====================================================================================
rommon 10 >
rommon 10 > set
PS1=rommon ! >
FE_PORT=0
WARM_REBOOT=
RET_2_RTS=20:35:55 UTC Thu Sep 25 2014
BSI=0
RET_2_RCALTS=
RANDOM_NUM=1600357627
?=0
IP_ADDRESS=10.0.0.3
IP_SUBNET_MASK=255.0.0.0
DEFAULT_GATEWAY=10.0.0.1
TFTP_SERVER=10.0.0.2
TFTP_FILE=
rommon 11 > TFTP_FILE=c2800nm-adventerprisek9-mz.124-24.T4
rommon 12 > TFTP_CHECKSUM=0
rommon 13 > SET
monitor: command "SET" not found
rommon 14 > set
PS1=rommon ! >
FE_PORT=0
WARM_REBOOT=
RET_2_RTS=20:35:55 UTC Thu Sep 25 2014
BSI=0
RET_2_RCALTS=
RANDOM_NUM=1600357627
IP_ADDRESS=10.0.0.3
IP_SUBNET_MASK=255.0.0.0
DEFAULT_GATEWAY=10.0.0.1
TFTP_SERVER=10.0.0.2
?=0
TFTP_FILE=c2800nm-adventerprisek9-mz.124-24.T4
TFTP_CHECKSUM=0
rommon 15 > tftpdnld
          IP_ADDRESS: 10.0.0.3
      IP_SUBNET_MASK: 255.0.0.0
     DEFAULT_GATEWAY: 10.0.0.1
         TFTP_SERVER: 10.0.0.2
           TFTP_FILE: c2800nm-adventerprisek9-mz.124-24.T4
        TFTP_VERBOSE: Progress
    TFTP_RETRY_COUNT: 18
        TFTP_TIMEOUT: 7200
       TFTP_CHECKSUM: No
        TFTP_MACADDR: 30:37:a6:49:35:a8
             FE_PORT: Fast Ethernet 0
       FE_SPEED_MODE: Auto
Invoke this command for disaster recovery only.
WARNING: all existing data in all partitions on flash: will be lost!
Do you wish to continue? y/n: [n]: y
ARP: address resolution for 10.0.0.2 timed out.
ARP failed with failure code 1. TFTP transfer aborted.
TFTP: Operation terminated prematurely.
rommon 16 >       " not found
rommon 17 >FE_SPEED_MODE=2
variable name contains illegal (non-printable) characters
rommon
rommon 18 > set
PS1=rommon ! >
FE_PORT=0
WARM_REBOOT=
RET_2_RTS=20:35:55 UTC Thu Sep 25 2014
BSI=0
RET_2_RCALTS=
RANDOM_NUM=1600357627
IP_ADDRESS=10.0.0.3
IP_SUBNET_MASK=255.0.0.0
DEFAULT_GATEWAY=10.0.0.1
TFTP_SERVER=10.0.0.2
TFTP_FILE=c2800nm-adventerprisek9-mz.124-24.T4
TFTP_CHECKSUM=0
?=0
rommon 19 > tftpdnld [ur]
usage: tftpdnld [-hr]
Use this command for disaster recovery only to recover an image via TFTP.
Monitor variables are used to set up parameters for the transfer.
(Syntax: "VARIABLE_NAME=value" and use "set" to show current variables.)
"ctrl-c" or "break" stops the transfer before flash erase begins.
The following variables are REQUIRED to be set for tftpdnld:
            IP_ADDRESS: The IP address for this unit
        IP_SUBNET_MASK: The subnet mask for this unit
       DEFAULT_GATEWAY: The default gateway for this unit
           TFTP_SERVER: The IP address of the server to fetch from
             TFTP_FILE: The filename to fetch
The following variables are OPTIONAL:
          TFTP_VERBOSE: Print setting. 0=quiet, 1=progress(default), 2=verbose
      TFTP_RETRY_COUNT: Retry count for ARP and TFTP (default=18)
          TFTP_TIMEOUT: Overall timeout of operation in seconds (default=7200)
         TFTP_CHECKSUM: Perform checksum test on image, 0=no, 1=yes (default=1)
          TFTP_MACADDR: The MAC address for this unit
               FE_PORT: 0= (default), 1
         FE_SPEED_MODE: 0=10/hdx, 1=10/fdx, 2=100/hdx, 3=100/fdx,
                        5=Auto (default)
      TFTP_DESTINATION: The flash destination device for the file
                        flash:(default), usbflash0:, usbflash1:
Command line options:
   -h: this help screen
   -r: do not write flash, load to DRAM only and launch image
rommon 20 > tftpdnld
          IP_ADDRESS: 10.0.0.3
      IP_SUBNET_MASK: 255.0.0.0
     DEFAULT_GATEWAY: 10.0.0.1
         TFTP_SERVER: 10.0.0.2
           TFTP_FILE: c2800nm-adventerprisek9-mz.124-24.T4
        TFTP_VERBOSE: Progress
    TFTP_RETRY_COUNT: 18
        TFTP_TIMEOUT: 7200
       TFTP_CHECKSUM: No
        TFTP_MACADDR: 30:37:a6:49:35:a8
             FE_PORT: Fast Ethernet 0
       FE_SPEED_MODE: Auto
Invoke this command for disaster recovery only.
WARNING: all existing data in all partitions on flash: will be lost!
Do you wish to continue? y/n: [n]: y
ARP: address resolution for 10.0.0.2 timed out.
ARP failed with failure code 1. TFTP transfer aborted.
TFTP: Operation terminated prematurely.
rommon 21 >

What I notice in the original post is this error
ARP: address resolution for 10.0.0.2 timed out.
which says that the router is looking for the 10.0.0.2 server but not getting response to its arp request. Can the original poster clarify for us how the device that has the image file is connected to the router that has the problem? Also what kind of device is 10.0.0.2? Is it a PC running TFTP server software or is it something else?
HTH
Rick

Cisco 2600 series router and cable modems

Hi everyone, I am just about to get started preparing for my CCNA... I am looking to pick up some used Cisco 2600 series routers to set up a home lab. I am wondering if it is possible to connect a cable modem directly to a 2600 series router? If so, do I need a certain type of WIC? I want to go from my cable modem, to a router, to my switch. Thanks in advance!

Hi,
Yes you can, using the Ethernet port on the cable modem, you can connect the cable modem to the router 2600, and the 2600 comes with builtin ethernet or fastethernet (according to your platform).
HTH,
Mohammed Mahmoud.

Cisco 7600 MPLS and set Qos group

Hi, i'm am trying to use to following class-maps and policy maps on a Cisco 7600. The same maps have been used on both 3700 series and 7200 series. However when i try to apply IP_TO_MPLS_OUT and MPLS_TO_IP_IN on the 7600 (with SUP32 and 48 port gigabit blade) i get a message on the console
"set qos group" not supported.
I used the QoS group to carry the MPLS EXP value (as label would is popped) and this works well.
How can i get the QoS group to work on the 7600, if not is there a valid workaround?
Many thanks for your help.
policy-map IP_TO_MPLS_OUT
class qosgrp5
set mpls experimental topmost 5
priority percent 10
class qosgrp4
bandwidth remaining percent 50
set mpls experimental topmost 4
class qosgrp2
bandwidth remaining percent 20
set mpls experimental topmost 2
class class-default
bandwidth remaining percent 30
random-detect
set mpls experimental topmost 1
policy-map CE_OUT
class qosgrp5
set ip precedence 5
class qosgrp4
set ip precedence 4
class qosgrp2
set ip precedence 2
policy-map MPLS_TO_IP_IN
class MPLS_EXP5
set qos-group 5
class MPLS_EXP4
set qos-group 4
class MPLS_EXP2
set qos-group 2

Hi,
I'm not aware that you can use qos groups on c7600 (LAN ports ?).
For the MPLS_TO_IP direction you can use 'mpls propagate-cos' on the egress interface as workaround. This rewrites the egress IP ToS with the internal DSCP (which is inferred from the topmost MPLS label).
For the IP_TO_MPLS direction you could just match on the original DSCP ?
cheers,
Stefan

NetConfig issue wrt Cisco 3900 Series Router

Hi Cisco;
I can't able to configure my Cisco 3900 series Router via NetConfig tool. While I am able to Configure all other Routers (7600, & 2800) and Switchs (6500, 3700, 3560). I can accessable 3900 Series Router via Inventory Collection, Sync Archieve, Campus Manager, DFM and etc.
I have Cisco LMS 3.2 with RME 4.3 & using SNMPV3.
Thanks for your support.
Best regards;
Shoaib Ahmed

Hi Clarke;
Please find the requested Screen Shot.
Actully my problem is that, I can't configure my Cisco 3945 Routers (Shows not applicable devices) via NetConfig tool. I can use other tools like Sync archieve and etc is working fine for these 3945 routers.
Best regards;
Shoaib Ahmed

Ethernet oam vs lldp

Hi,
May be basic funda question. When to enable 'ethernet oam' and 'lldp'.
I know lldp is cisco to non-cisco layer 2 communication.
What is the difference between oam and lldp and when to use?
Regards
Siva K

Hi,May be basic funda question. When to enable 'ethernet oam' and 'lldp'.I know lldp is cisco to non-cisco layer 2 communication.What is the difference between oam and lldp and when to use?RegardsSiva K
Hi Siva,
The difference between Ethernet OAM and LLDP is ethernet OAM protocol for installing, monitoring, and troubleshooting Metro thernet networks and Ethernet WANs relies on an optional sublayer in the data link layer of the OSI model.
OAM frames, called OAM protocol data units (OAM PDUs) use the slow protocol destination MAC address 0180.c200.0002. They are intercepted by the MAC sublayer and cannot propagate beyond a single hop within an Ethernet network. Ethernet OAM is a relatively slow protocol, with a maximum transmission rate of 10 frames per second, resulting in minor impact to normal operations.
On the other hand the LLDP says to support non-Cisco devices and to allow for interoperability between other devices, the switch supports the IEEE 802.1AB Link Layer Discovery Protocol (LLDP). LLDP is a neighbor discovery protocol that is used for network devices to advertise information about themselves to other devices on the network. This protocol runs over the data-link layer, which allows two systems running different network layer protocols to learn about each other.
Hope to Help !!
Ganesh.H
Cisco are currently donating money to the Haiti earthquake appeal for every rating so please consider rating all helpful posts.

Cisco 1200 series upgrade failure

I have a Cisco 1200 Series (AIR-AP1231G-A-K9) access point, I have been upgrading these models to lightweight mode but are having issues with one in particular, this access point keeps "rebooting" itself, I am assuming that the upgrade faild, how can I get the access point upgraded?
Here is a capture.
Cisco IOS Software, C1200 Software (C1200-RCVK9W8-M), Version 12.3(11)JX1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Mon 17-Jul-06 11:41 by alnguyen
Image text-base: 0x00003000, data-base: 0x00359FC0
Initializing flashfs...
flashfs[1]: 4 files, 2 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 7741440
flashfs[1]: Bytes used: 1862656
flashfs[1]: Bytes available: 5878784
flashfs[1]: flashfs fsck took 2 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.
cisco AIR-AP1231G-A-K9 (PowerPC405GP) processor (revision B0) with 15038K/1336K bytes of memory.
Processor board ID FTX0914J0Z1
PowerPC405GP CPU at 196Mhz, revision number 0x0145
Last reset from reload
LWAPP image version 3.0.51.0
1 FastEthernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:13:7F:E2:34:DB
Part Number : 73-8704-08
PCA Assembly Number : 800-23211-09
PCA Revision Number : A0
PCB Serial Number : FOC09100NH1
Top Assembly Part Number : 800-23304-08
Top Assembly Serial Number : FTX0914J0Z1
Top Revision Number : A0
Product/Model Number : AIR-AP1231G-A-K9
Press RETURN to get started!
*Mar 1 00:00:04.505: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1200 Software (C1200-RCVK9W8-M), Version 12.3(11)JX1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Mon 17-Jul-06 11:41 by alnguyen
*Mar 1 00:00:05.442: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:06.442: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to down
ap>
ap>
*Mar 1 00:00:14.441: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Mar 1 00:00:23.516: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Mar 1 00:00:23.544: LWAPP_CLIENT_ERROR_DEBUG: lwapp_crypto_init_ssc_keys_and_certs no certs in the SSC Private File
*Mar 1 00:00:23.544: LWAPP_CLIENT_ERROR_DEBUG:
*Mar 1 00:00:23.544: lwapp_crypto_init: PKI_StartSession failed
*Mar 1 00:00:23.698: %SYS-5-RELOAD: Reload requested by LWAPP CLIENT. Reload Reason: FAILED CRYPTO INIT.
*Mar 1 00:00:23.698: %LWAPP-5-CHANGED: LWAPP changed state to DOWNXmodem file system is available.
flashfs[0]: 4 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 7741440
flashfs[0]: Bytes used: 1862656
flashfs[0]: Bytes available: 5878784
flashfs[0]: flashfs fsck took 9 seconds.
Reading cookie from flash parameter block...done.
Base ethernet MAC Address: 00:13:7f:e2:34:db
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
ethernet link up, 100 mbps, full-duplex
Ethernet port 0 initialized: link is up
Loading "flash:/c1200-rcvk9w8-mx/c1200-rcvk9w8-mx"...#########################################################################################################################################################################
File "flash:/c1200-rcvk9w8-mx/c1200-rcvk9w8-mx" uncompressed and installed, entry point: 0x3000
executing...
Restricted Rights Legend

I might have an answer for you... or I might be COMPLETELY WRONG
If it isn't just a "failed" upgrade, as in you've tried the upgrade again and it still is happening.... I was reading something about older APs not have a Manufacturing-installed certificate (MIC) and these AP's generating a Self-signed Certificate (SSC).
The error you have is referring to SSC so I'm writing this as if you have not had to previously do this step for your other conversions.
I believe a couple of things needs to happen for SSC AP's.
1) Must enable controller to accept self-signed certificated.
Security > AAA > AP Polices > Accept Self Signed Certificate > Apply
2) Add AP to Authorization List in Security > AAA > AP Polices > Add AP To Authrorization List
Enter MAC Address of the AP
Certificate type = SSC
SHA1 Key Hash can be obtained from the controller by issueing this command:
"debug pm pki enable"
Look for the line: sshpmGetIssuerHandles: SSC Key Hash is XXXXXXXXXXXXXXXXXXXXXXXXXX
I believe you use the XXXXXXXXXXXXXXXXXXXXX as the SHA1 Key Hash.
3) If required, you may also need to add the AP MAC Address in the Mac-Filter: Security > AAA > MAC Filtering > New >
Hopefully its either a reload of the software or this SSC thing that fixes the problem....

What are the following:1)Cisco 1600 Series IOS WIRELESS LAN RECOVERY. 2)Service Provider Option 60 for Vendor Class Idenfier

What are the following:1)Cisco 1600 Series IOS WIRELESS LAN RECOVERY. 2)Service Provider Option 60 for Vendor Class Idenfier
These items are listed with 1600 series AP but I'm unable to understand what are these things & the use of them

DHCP Option 60: Go HERE.

How to bridge a linksys cisco E1200 series router?

I have recently purchased a linksys cisco E1200 series router and would like to know how to bridge the connection to my xbox

purchase 881w, get rid of linksys. That should do it.
Sent from Cisco Technical Support iPad App

Need a tool for flash backup on Cisco 2821 series routers

Hello Folks,
We have around 1200-1500 cisco 2821 series routers on those we are performing the hardware upgrade so we are taking the backup of all the files available in the flash of all the routers, we just want to know is there any trusted tool available to make this task easy to schedule and take the backups.
Please let me know if you know any tool name.
Thanks,
Raja.

Sorry, I don't know any tool that makes a backup of the whole flash...
You could fo it with from ios cli maybe execute it automatically...
To flash:
archive tar /create flash:/backup.tar flash:/
copying directly to ftp should also work:
archive tar /create ftp://test:[email protected]/backup.tar flash:/

Cisco works LMS 3.0.1 cannot archieve configuration for cisco 3000 series vpn concentrator

Hi All,
Our problem is, we have Cisco Works LMS 3.0.1. cannot archieve configuration for cisco 3000 series vpn concentrator.
Any help would be greatly appreciated.
Thanks in advance.
Samir

Make sure you have filled out all of the HTTP/HTTPS credential data in DCR for these devices. RME will only use HTTPS to fetch VPN concentrator configurations.

IP SLA/Ethernet OAM on Cisco 7600 Series

Similar Messages

Maybe you are looking for