IP4 3G Internet max speed?
What is the max download speed for iP4 over 3G? I just tested and got 765kbps. Thank you.
The HSDPA-Standard supports up to 3.6 / 7.2 Mbit/s (download)
Similar Messages
-
WRT160N Slow Internet Connect Speed, while connected wired.
Ive tried two of these routers both from best buy, I took the other one back thinking it was a problem with the router which it still maybe. But, I have 20meg internet and when I run a speed test im only getting 6-7megs. When I directly connect the modem to the computer I get the full speed with no problems. I used to use the old BEFSR41 router and that always had max speed(Now the power light flashes on it, it goes steady then it starts blinking if anyone could help me with this one to would be great). But I don't know what to do.
Thanks.
Justin.Open the setup page of the router and reduce the MTU to 1350 and click on save settings..Power cycle the router and check...On the BEFSR41 as the power light keeps flashing..it seems that it gone bad...However you may try by resetting the router for 1 minute and if the power light stops blinking then,you can configure the router.
-
Max speed 1.0Mbps?
Why is the max speed that I get with my WRT150N 1.0Mbps? It doesn't matter where I'm at in the house, it doesn't matter if its an HP laptop, Dell laptop etc...the max speed i get is 1.0Mbps?
What is the speed you are getting when you connect the computer straight to the Modem...?
What is the speed you are getting on the wired computer(computer connected to the router via ethernet cable)...?
Try upgrading your Router's Firmware and then reconfigure it...
Go to website linksysbycisco.com/downloads.........insert model no of your router in serach tab......select proper version of your router........download the firmware file......save that file on desktop
Follow these steps to upgrade the firmware on the device : -
Open an Internet Explorer browser page on a computer hard wired to the router...
In the address bar type - 192.168.1.1...Leave the Username blank & in Password use admin in lower case...
Click on the 'Administration' tab- Then click on the 'Firmware Upgrade' sub tab- Here click on 'Browse' and browse the .bin firmware file and click on "Upgrade"...
Wait for few seconds until it shows that "Upgrade is successful" After the firmware upgrade, click on "Reboot" and you will be returned back to the same page OR it will say "Page cannot be displayed".
Now reset your router :
Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...
If your Internet Service Providor is Cable follow this link
If your Internet Service Providor is DSL follow this link -
My macbook internet download speed is extremely slow. I have tried 2 other computers, another mac and windows and the download speed is over 10mb but with this macbook pro it is less than 1mb. What is causing this and how to fix?
To find out how much space you have & what is left, open up Disk Utility/Machintosh HD/First Aid. The info will be at the bottom of the window.
Sluggish Finder - Bunch of icons on your desktop? An overcrowded desktop slows down your Mac.
Get rid of needless Finder calculations - Open a window in Finder/View/Show View Options: ensure "Calculate All Sizes" option is unchecked.
Internet related - It's likely that your broadband connection is the bottleneck. You can check your speed on http://www.speedtest.net to see how fast your connection is. If your web browser specifically performs slowly, quit and relaunch it.
If browser remains sluggish, empty its cache.
Safari/Empty Cache
Firefox/Preferences - select the Network tab of the Advanced preferences and click the "Clear Now" button in the "Offline Storage" area.
Application related - Launch "Activity Monitor" - Applications/Utilities - click the CPU heading and see what float to the top. If an application takes up a large chunk of CPU and won't let it go, it could be dragging down your Mac's performance. Quit it by clicking the Quit Process button at the top of the Activity Monitor window.
Too little ram - max out your ram.
Solution may be found if you search in the "More Like This" section over in the right column. -
Slow Internet download speed, OSX 10.9.5
Since updated to 10.9.5, my Mac Pro Internet download speed down to 7 Mbps,
and same on My MacBook Pro 10.9.5 too. both use to be 70 Mbps.
I am paying $50.00 extra to get the highest speed from Time Warner.
My iMac is 10.9.3, tops 70 Mbps.
My iPhone 5s tops tops 30 Mbps
All in same WiFi network.
Upload speed all seem to be fine with 5 Mbps.
Mac Pro = Mid 2010
Processor 2.8 GHz Quad-Core Intel Xeon
Memory 16 GB 1066 MHz DDR3 ECC
Graphics ATI Radeon HD 5770 1024 MB
Mac Book Pro = Retina, 13-inch Late 2012
Memory = 8 GB
Something wrong!Even the 'respected' tools like Onyx, if you look at what (each and every update) states in the "what is new" and changes will be to improve compatibility.
Never use or install anything (and I include OS X updates in that category) without cloning your system and having TimeMachine that is current, and backup(s) that will be off line.
Some cannot be trashed or deleted or removed without using an "uninstall app" or the installer, doing so without can mean having to reinstall first.
Or wipe the drive and restore from a known good backup set.
Some tips:
https://discussions.apple.com/thread/6522256
What to look for if your system is slower than normal etc:
https://discussions.apple.com/thread/4873022
for malware, check out this user tip (and his other pages too!) -
Slow Internet Connection Speeds caused by Ethernet Controller Driver
Problem: Internet connection speeds are 1/10 of available connection speed.
1. Problem statement is based on running speed tests at cnet, speedtest.net, and AT&T.
2. I am paying for 12 MBps down load speed but I only get about 1.5 MBps.
3. Other computers in household get 11+ MBps connected to the same ethernet cable and also different ethernet cables.
4. I traced the problem to the network controller driver.
5. I updated to the latest driver with no change in performance.
6. After some experimenting I found that if I re-install the driver after the computer is booted up, the internet connection down load speeds increase to 11+ MBpS (typically around 11.4 with maximum capability of 12)
I have assumed that the driver does not load properly the first time, but why? Or is there some other cause or setting that I have overlooked?
Board: MSI Z77A-G43
Bios: Version 2.0
Ethernet Controller: RealTek RTL8168B PCIe GBE Family Controller
Ethernet Controller Driver: 7.65.1025.2012
VGA: NVIDIA GeForce GTX 550 Ti
PSU: Raidmax RX630Z 630W
Intel Core i7-2700K Sandy Bridge 3.5GHz LGA 1155 95W
MEM: 4x4gb
HDD (Primary): Western Digital WD5000HHTZ-04N21V0 500MB
HDD (Secondary): Hitachi Deskstar HDS723020BLA642 2TB
OS: Windows 7 64bit ProfessionalHave you installed all of the most recent drivers:
http://www.msi.com/product/mb/Z77A-G43.html#/?div=Driver&os=Win7%2064
There is also an realtek firmware update included in the latest bios:
>>Beta BIOSes<<
2.8 is the latest official & there are two newer beta bios's there as well. -
''locking - dupe of https://support.mozilla.org/en-US/questions/976623''
there is an icon in the upper right hand corner about test your internet connection speed. is this malwareCan you attach a screenshot?
*http://en.wikipedia.org/wiki/Screenshot
*https://support.mozilla.org/kb/how-do-i-create-screenshot-my-problem
Use a compressed image type like PNG or JPG to save the screenshot.
Start Firefox in <u>[[Safe Mode|Safe Mode]]</u> to check if one of the extensions (Firefox/Firefox/Tools > Add-ons > Extensions) or if hardware acceleration is causing the problem (switch to the DEFAULT theme: Firefox/Firefox/Tools > Add-ons > Appearance).
*Do NOT click the Reset button on the Safe Mode start window.
*https://support.mozilla.org/kb/Safe+Mode
*https://support.mozilla.org/kb/Troubleshooting+extensions+and+themes -
My internet download speed, which averages just over 5 Mb/s most of the day, slows to about 1 Mb/s every night at about 8:30-9:00 P.M. Pacific Time and lasts for a few hours. It is consistent and constant so random equipment or line problems are unlikely. I've saved the results of my speed tests (speedtest.net) as to evidence the problem and posted them below.
Please help.
DATE/TIME Download Upload
10/25/2011 5:24 PM GMT 5.34 Mb/s 0.73
10/24/2011 3:28 AM GMT 1.31 Mb/s 0.73
10/22/2011 4:54 AM GMT 1.20 Mb/s 0.73
10/21/2011 6:40 AM GMT 5.34 Mb/s 0.66
10/21/2011 5:08 AM GMT 0.93 Mb/s 0.73
10/19/2011 6:51 PM GMT 4.86 Mb/s 0.61
10/19/2011 1:05 AM GMT 5.35 Mb/s 0.72
10/18/2011 4:47 PM GMT 5.34 Mb/s 0.72
10/18/2011 3:58 AM GMT 0.92 Mb/s 0.73
10/12/2011 4:26 AM GMT 0.94 Mb/s 0.72
10/12/2011 4:01 AM GMT 1.00 Mb/s 0.72
10/11/2011 4:00 PM GMT 5.35 Mb/s 0.70
10/11/2011 4:51 AM GMT 1.43 Mb/s 0.73
10/11/2011 4:18 AM GMT 1.14 Mb/s 0.73
10/11/2011 1:12 AM GMT 5.35 Mb/s 0.70
10/10/2011 4:13 AM GMT 0.96 Mb/s 0.72
10/9/2011 4:42 AM GMT 5.34 Mb/s 0.71
10/8/2011 5:13 AM GMT 1.37 Mb/s 0.73
10/8/2011 4:58 AM GMT 0.95 Mb/s 0.36
10/7/2011 10:47 PM GMT 5.34 Mb/s 0.69
10/7/2011 3:07 PM GMT 5.36 Mb/s 0.70
10/7/2011 4:58 AM GMT 1.17 Mb/s 0.73
10/7/2011 4:35 AM GMT 1.20 Mb/s 0.73
10/6/2011 3:41 PM GMT 5.35 Mb/s 0.71
10/6/2011 6:03 AM GMT 5.07 Mb/s 0.70
10/6/2011 5:10 AM GMT 1.15 Mb/s 0.73
10/6/2011 4:39 AM GMT 1.13 Mb/s 0.73
10/5/2011 3:08 PM GMT 0.76 Mb/s 0.14 Looks and sounds like the usual case of congestion during prime time hours. Have you tried asking Verizon to change the circuit or edge router your DSL line connects to, in order to solve the problem? Often times there seems to be an imbalance in how circuits are loaded on Verizon's DSL network. It's a rather typical experience for a shared medium (such as DSL, Cable) but steps can be taken to try and balance off load periodically. Verizon should have some free circuits available that will allow you to reach your speeds during the night time hours.
========
The first to bring me 1Gbps Fiber for $30/m wins! -
Is it possible to increase internet access speed of Mackbook Pro OS X 10.5.8 whilst using telstra prepaid wirless broadband internet stick in Darwin, Australia?
How can i do this?Network Utility (in the Utilities folder) can tell you, in the Info pane, what speed you are actually connecting at.
Just set the interface to the one you are using (which may show up as en2 or something). Link Staus and speed are shown along with error counts.
If the data rate is very different from what you expected, you may have it manually set to a lower rate.
YouTube files are enormous -- that may be the best it can do. -
Low internet download speed when on battery (have tried previously given fix)
There is a drastic fall in internet download speeds when laptop is running on battery power. As soon as I plug it in, the internet speeds return to normal.I have already changed the wireless settings to high performance in the power management profile.How do I solve this problem?Any help is appreciated. Also, my laptop is only a couple days old.
Hi there , Thank you for visiting the HP Support Forums and Welcome! This is a great site to get answers and ask questions. I have looked into the issue you are having with Battery Performance and I found a couple of documents for you to try. The first document I found is called HP Notebook PCs - Managing Power Options (Windows 8). In this document it shows you how to create your own Power Plan. The second document I found is called HP Notebook PCs - Testing and Calibrating the Battery (Windows 8). You can test and calibrate the battery to make sure that it is not an issue with the battery itself. Please follow these provided troubleshooting steps, re-post and let me know how everything went. Thank you! Have a great day!
-
Linksys router EA6200 slow speed, low max speed, Configuration issue
Hi Guys,
I am using Comcast internet 105MBPS speed and I am using NETGEAR DOCSIS 3.0 High Speed Cable Modem (CM400-100NAS) model and I am connecting linksys EA6200 router.
I am getting 90 to 100 Mbps if I connect my laptop with modem directly, but if I connect my laptop over wifi or connect router with laptop using wired connection as well, I am only getting 30 to 40 Mbps speed.
Can you pleaes help me? what did I wrong. Please let me know if you need more information.
Regards,
-Dhaval M.Do a network reboot (router and modem) and check again the speed. If you'll get the same result, try a manual firmware update and after that, reset and reconfigure the router.
Adjusting the MTU size might help as well. To determine the best size, go to this link. -
Re: Satellite L855 - max speed with newest SSD
I am looking to buy this notebook
+Message was edited: broken link has been removed+
(Croatian language, but will help)
I am wondering if there is SATA 6GB/s so I can buy newest SSD to use max speed?
thanks,
Mario> I am wondering if there is SATA 6GB/s so I can buy newest SSD to use max speed?
I guess you are speaking about the Satellite L855 series since this model mentioned in your subject.
I dont think that Satellite L855 supports an SATA III HDD controller.
I think its SATA I, maybe SATA II
My notebook supports SATA I (1.5Gb/s) and I upgraded the unit with an SSD SATA III drive (6Gb/s). The SSD works fine but of course it does not reach the full 6Gb/s due to the HDD controller limitation. -
Hi,
A very quick question if I may?
What is the max speed that the version 1 of the BT Hub is capable of delivering?
Thanks,
Arnak
Solved!
Go to Solution.Here are my home hub 1 stats. Upload speed is usually about 1.2 mb, but dropped due to some noise recently.
It will sort itself out eventually.
DSL Connection
Link Information
Uptime:
13 days, 10:20:51
Modulation:
G.992.5 annex A
Bandwidth (Up/Down) [kbps/kbps]:
846 / 12,437
Data Transferred (Sent/Received) [GB/GB]:
1.50 / 13.05
Output Power (Up/Down) [dBm]:
12.5 / 0.0
Line Attenuation (Up/Down) [dB]:
18.0 / 33.5
SN Margin (Up/Down) [dB]:
11.5 / 4.5
Vendor ID (Local/Remote):
TMMB / IFTN
Loss of Framing (Local/Remote):
0 / 0
Loss of Signal (Local/Remote):
5 / 0
Loss of Power (Local/Remote):
0 / 0
Loss of Link (Remote):
0
Error Seconds (Local/Remote):
1,201 / 0
FEC Errors (Up/Down):
0 / 662,385,328
CRC Errors (Up/Down):
0 / 31,836
HEC Errors (Up/Down):
0 / 29,524
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones. -
Max speed with Auto Flip?
Hi!
I need to scan a few pdf documents at fast speed as part of my work. I set the Auto Flip speed to 0.02 seconds in page transitions. Is this speed too fast for a 60Hz monitor? Will Acrobat be able to display all pages at this speed or will it miss some pages out? Also, is there a drop in quality this way or will all the images and text be catched and displayed in full quality at 0.02sec autoflip speed?> I am wondering if there is SATA 6GB/s so I can buy newest SSD to use max speed?
I guess you are speaking about the Satellite L855 series since this model mentioned in your subject.
I dont think that Satellite L855 supports an SATA III HDD controller.
I think its SATA I, maybe SATA II
My notebook supports SATA I (1.5Gb/s) and I upgraded the unit with an SSD SATA III drive (6Gb/s). The SSD works fine but of course it does not reach the full 6Gb/s due to the HDD controller limitation. -
Max speed support on serial 2503
Hi All,
I have a router cisco 2503, I need to know what is Max. speed supported on serial interface? Presently we have 128KB leased line, and want to know weather I can upgrade the leased line to 256K with the same router ?
THanks,
A.SHello,
if you are referring to the two serial interfaces on your 2503, these are high-speed serial interfaces, which support speeds up to 2048kbps, or roughly 2MB.
Check this link for more details:
Cisco 2503 Router
http://www.manucomp.com/cisco_catalogue/cisco_2503_router.html
HTH,
GP
Maybe you are looking for
-
Background job hanging reasons
background job hanging reasons
-
Apple tv streaming from a webside ?
I just got a apple tv and I like to know if I'm watching a movie on a webside with my iMac can I move that to my tv using apple tv? Thanx
-
I have iTunes installed on my Windows 7 machine. When waking up my Windows 7 machine I get a message that says that APSDaemon.exe can't start because MSVCR80.dll is missing. I'm directed to reintall the applicaton. Is this iTunes related? If so,
-
Unicode presentation in browser - Urgent
Hi all, 1. My database is UTF8 2. Client is JSP 3. The charset set in JSP is UTF-8. 4. In that case will it prompt for installing font at the client side when presenting languages like japanese, korea, chinese etc., TIA RSrinivasan
-
Regular Expressions and phone number
HI, there is a column "Phone_number Varchar2" Data containing : 123-89556-6852 (123)-857-965 123-(5846)5648 I want to display that 123895566852 123857965 12358465648 Pls help by Regular Expressions. Edited by: YLN on Feb 17, 2010 3:59 PM