IPad 2 cannot connect to Wifi before and after updating PLEASE HELP

i have been using iOS 5.1.1 till today.. the connection to wifi stopped working.. it slowly faded away and today i woke up and could not connect to My wifi at all, i have decided to update my iPad to iOS 7.0.4 but the problem is there
what should i doo ??

It could be a problem with your WiFi router or your iPad.
If you are having WiFi problems it is necessary to isolate whether the problem is with your network or your iPad. Note: Do NOT consider your network to be blameless if some other devices can connect to it.
First, test your iPad on some other WiFi networks: a friends, Starbucks, Barnes & Noble, etc.
If it works well there then the problem is probably with your network. Try restarting your WiFi router by removing power for 30 seconds. If that does not help check for a firmware update for your router. If none exists which corrects the problem consider replacing the router.
If your iPad does not function well on other networks it possibly has a hardware problem. You could try Settings > General > Reset > Reset Network Settings to see if that corrects the problem. If not, contact Apple Support or visit an Apple store for evaluation. They can provide a replacement if your iPad is bad.
If you need more help please give the make, model, and version of your WiFi router and how you have it configured.
See also here: http://www.apple.com/support/ipad/wifi/

Similar Messages

Got my ipad mini. It works perfectly fine until I updated to ios 6.0.2. Now I can't connect to wifi. I've tried every solutions offered in every forums and internet sites but nothing happened. Still ipad cannot connect to wifi. HELP!!!

Got my ipad mini. It works perfectly fine until I updated to ios 6.0.2. Now I can't connect to wifi. I've tried every solutions offered in every forums and internet sites but nothing happened. Still ipad cannot connect to wifi. HELP!!!

Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
    •    Launch Settings app
    •    Tap on Wi-Fi
    •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
    •    In the window that opens, tap on the Renew Lease button
~~~~~~~~~~~~~~~~~~~~~~~~~
iOS 6 Wifi Problems/Fixes
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
How to Fix a Poor Wi-Fi Signal on Your iPad
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Connect iPad to Wi-Fi (with troubleshooting info)
http://thehowto.wikidot.com/wifi-connect-ipad
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

My Ipad is connected to wifi but won't update any apps, Facebook etc

My Ipad is connected to wifi but won't update. Can't update apps, and even Facebook will not update (Newsfeed). Can anyone tell me how to fix this? Thanks.

Hello mjb32,
We've an article which provides information and troubleshooting steps that can help get your WiFi connection working.
iOS: Troubleshooting Wi-Fi networks and connections
http://support.apple.com/kb/TS1398
Cheers,
Allen

Repairing permissions before and after updating software

What is the reason to repair permissions before and after updating software? This may sound like a stupid question to many of you, but I am new to computers and I am trying to learn how and why of some of the things of my PowerBook. I installed some updates without repairing permissions. Did I install some software updates the wrong way? Thank you.

This is a topic which will draw as many emphatic for and against responses as overnight shut down or not, defrag or not, optimise or not, and so on.
I agree with Neil. I believe that OS X has progressed sufficiently that repair permissions has become redundant and so I do not do it on any regular basis.
Some folk may refer you to an Apple Support Article 303602. That Article in its 4 May 2006 version, titled "Top 10 Tips to Keep Your Mac in Top Form" suggested Repair Permissions should be done "after upgrading or installing new software". The Article was however revised on 15 May 2006 to be titled "Top Tips to Keep Your Mac in Top Form" and the item on Repair Permissions [along with two other recommended maintenance tips] was removed. It is my view that the conclusion to be drawn here is that Apple no longer considers Repair Permissions to be a required maintenance procedure.
Many users have adopted a "Repair Permissions" mantra for a cure-all over several years. I dropped it sometime in 10.3.
But, to each his own.
HTH
TiPB 867 Mac OS X (10.4.6)

Oracle Alert: Access before and after update values of a table column

We have a requirement where a notification needs to be sent when 'END_DATE' attribute (column in a table X) is set, in an Oracle Applications form.
I have defined an Event based Oracle Alert which fires 'On Update' of the table X.
Could anyone please let me know as how to access the value of 'END_DATE' before and after update (i.e :new.END_DATE and :old.END_DATE) in the sql query of the alert.
The need to use the before update and after update values of the attribute 'END_DATE' is that if we add the condition END_DATE is not null, the alert is sent even if any other attrbutes are updated in the Oracle form which is not the intended behavior.
Appreciate any help.
Thanks

Hi
use selectionlistener for your first table then add clientlistener and serverlistener so that you will get the rows on click in back bean.
then get second table vo and and create and add row for that view object. add partial target to refresh your second table from back bean.
on click of save call commit operation.

Triggers before and after update

Hi
I would like to add triggers before and after update for the following code. I would be thankful if someone give some guidance
update per_all_people_f a
set start_date = (select min(effective_start_date)
from per_all_people_f a1
where a1.person_id = a.person_id)
where person_id in (1114,115);Thanks
anna

Hi
I was unable to answer you. I agree with Peter . Also i want to add
that in HRMS you should check what triggers are already on that table and be carefull with creating your own one. With your own trigger you can influence on some application logic you know.
( And i hope that is a table first of all :) - but as i know _F at the end of table name means table )
T

Cannot connect to itunes store before and after update ios 8.2, What can i do ?

I updated to iOS 8.2 about 2 hours age and I get an error saying "cannot connect to iTunes Store" every time I try to update existing apps or download new apps. I restarted my phone, disconnected from wifi, reconnected to wifi...nothing is working. Under iTunes & App Store settings, I signed out and now get the "cannot connect to iTunes Store" message when trying to sign back in. I know my Apple ID and password are correct.

Based on the numerous posts regarding iTunes and the App Store, there appears to be an issue at Apple's end. Although Apple has not provided any indication on the cloud status page.
Do not change your settings.

Ipad not connecting to iTunes on laptop after updated to iOS 6

After I updated my ipad to iOS 6 I cannot connect it to my laptop to add music to it, what can I do?

Did you try rebooting your computer? Sometimes that can help you get started in situations like this. Did you launch iTunes on your computer as well?
Antivirus software can cause problems with PC's trying to connect to iTunes so you can try disabling your AV software and try again to connect.
You may need to restore. See the end of this article to restore.
http://support.apple.com/kb/TS3281
If the device is not being recognized you can put the iPad into recovery mode to restore.
http://support.apple.com/kb/ht4097

Error uploading file to web before and after updating

Hi,
I'm running adobe muse on a mac 2013 yosemite. I changed from the original version of adobe muse to the 2014.2 version, just to let you all know.
Earlier today, I woke up and one of my two websites I've created in the original version of adobe muse had lost the information required to upload to FTP Host. I retyped in my information, and it started to upload my website. Eventually it hit the 61% mark, and said that it was "connecting to the FTP host" for a really, really long time. I waited about 20 minutes- nothing happened. So I then decided to update adobe muse to the 2014.2 version.
After updating, I tried uploading my site to the web again. I put in virtually the same information as before, and now I'm getting an error message saying "Could not sign in. Check your network connection and try again. If this problem persists, try again later."
Can anybody help me here? My website is hosted by GoDaddy.com, just to let you know.
Thanks in advance,
Gavin

Muse 2014.3 was released last week , please tr y to update Muse and then check.
Thanks,
Sanjit

Whenever I try to open my Wifi Connection at home, it doesn't work! It just stays on 3G, and I want to update my phone, but In order for me to do this, I have to connect through WiFi to ignore additional charges, please help!

Hey! So basically, I've been using my Wifi connection (from home) lately, I had no troubles what-so-ever. I turned on my 3G network this morning, and again, everything's going perfectly fine with my connection. I came home around half 4 from school and decided to turn on my Wifi connection at home, what I've realised is that whenever I try turning on my Wifi network, the little sign that's usually at the top doesn't appear anymore. I tried resetting the network settings and closing and opening my phone, but.. This didn't really make any difference. I'm really worried and I don't know what to do! I have tried reconnecting to my Wifi but nothing happened, my Bluetooth's never really turned on. Please help!!

I'm not sure if I'm understanding but if I am then I'm not sure why you are turning your Wi-Fi off and on. It should automatically connect and use your Wi-Fi when it is available and use your cellular data connection when Wi-Fi is not available. I haven't turned either off ever. However, more to the point of your current problem, the following has some troubleshooting steps that may help: http://support.apple.com/kb/TS1398

Cannot connect to server with icloud after updating to ios7 in iphone 4s

icloud will not connect to server after updating to ios7 on my iphone4. I have spoken to tech support and the response was that the server is crashing because of all the activity. Sounds pretty lame to me. With a company as large as Apple, this really is unacceptable. I have tried everything I can think of to get this to work, but to no avail.

voicemail is a carrier feature, so contact verizon.

Cannot Connect To BIS! Tried Everything! Please Help!

Hello. This is such a complicated problem so it may take a while to explain.
I have a Blackberry Bold 9700. Ive had it from May 2010, I had a restriction on my phone for no more than 3 hours, and when my services came back on my BIS wouldnt work.. But here is the weird thing.. I can access webpages, Its just apps and also blackberry messenger that wont work. My phone says 3G and has the blackberry symbol at the top right hand corner.
I phoned up o2 (I have done 4 times) and they told me to do the following:
options > advanced options > host routing table > blackberry button > register now
this didnt work so they suggested this:
setup > set up email
this didnt work either, so they also suggested this:
o2email.co.uk > register
so the final thing they told me to do was
settings > advanced options > service book > and delete everything apart from anything that says provisioning and had my email address in it > reboot
but this didnt work either! they said my connections to the blackberry network were active and fine and i should be recieving this all. I have rebooted my blackberry several times, and it has been almost a week since this happened so this should be enough time for the network to come back through!
Can someone please help?! Ive contacted o2 so many times and they dont seem be able to fix the problem!
Thanks!

Hey xKimberella,
Welcome to the forums.
When you say "I had a restriction on my phone for no more than 3" what exactly do you mean? Who put the restriction on your device?
I suspect that you do not have the correct data plan to allow you to use BBM and setup email. Have you recently changed your service plan?
-SR
Come follow your BlackBerry Technical Team on twitter! @BlackBerryHelp
Be sure to click Kudos! for those who have helped you.Click Solution? for posts that have solved your issue(s)!

My phone won't power up after updating please help

My phone will not power up after updating...it's been three hours...please help

Hey laurelletoo,
Welcome to Apple Support Communities.
From what I gather, there’s an issue turning your iPhone 5 on after updating it. Take a look at the article below and try running through the suggestions that it provides.
If your iPhone, iPad, or iPod touch doesn't respond or doesn't turn on - Apple Support
Take care,
-Jason

Serious Issues after update, PLEASE HELP!!!!

Two nights ago i did a software update. Shut the computer down everything was fine. Im not sure the software update worked properly. When i restarted the computer later that evening, all i got was the gray screen with the apple. A friend was searching forums for me over the internet while we were trying to fix it. Did the CTRL OPTION R P thing and that didnt work. Did the CTRL S and that didnt work. Next day went and bought a Snow Leapord cd. After three hours the status bar moved appx 3/4 of an inch. Took it to apple. They wiped the Hardrive clean and reinstalled Snow Leapord to it. Now it restarts and operates. However, it takes about 15 min for it to start up and get to the desktop and it runs TERRIBLY slow. It has a 500g hard drive that was put in 2 weeks ago. It also has 2g of RAM. After taking it to apple it is only showing 1.5G of RAM after the wiped the hard drive. PLEASE HELP ME!!!!!! Everything was working fabulous prior to 2 nights ago.

Well I just rewiped the hardrive clean and reinstalled snow leapord. IT WORKED!!!!!! Computer is running fast as could be, start ups in less than 30 seconds, no lagging. Im really happy as i bought this computer from a good friend and its less than a week since ive had it. I think ill just live with the ram still showing 1.5g. I think ill wait and just go get 2 4g sticks when i get around to it that way It will be as fast as possible and ill be using the ports to their full potential.

Couldn't and can't connect to iTunes or game center before and after updating to 8.2

Okay so i was playing clash of clans and signed out of my Game Center and when i went to sign back in I was given the error saying there wasn't communication with the server. I tried signing out of iTunes and back in and that wouldn't let me connect. Does anybody know how long this is going to last?

Check the system status here: http://www.apple.com/support/systemstatus/

IPad 2 cannot connect to Wifi before and after updating PLEASE HELP

Similar Messages

Maybe you are looking for