Ipad 2 froze on usb plug and itunes....HELP ME PLEASE

I went to update my ipad 2 tonight with the newest update. And while it was updating...it froze and now it is stuck on usb plug and itunes......I can not turn it off or anything...It was backed up before this happened...What do I do...Please explain in very detail information....I turned off computer, I have tried a new plug...it still is frozen...HELP ME PLEASE

Put iPad in Recovery Mode
http://support.apple.com/kb/ht4097

Similar Messages

  • After battery flat, usb plug and itunes icon appear and unable to restore

    last 2 weeks, my phone didn't work anymore.
    my screen turn up with usb plug and itunes icons.
    i tried to connect my phone to the computer, itunes was open.
    i pushed the offbutton on the top and i pushed the home button for 10 sec.
    then, i only pushed the home button.
    i got a message from itunes, saying that he found a phone to restore.
    i did restore, but at the end: i got following message:
    " couldn't be restored, error 28".
    i tried to restore my phone in DFU modus (like i read on forums), but it doesn't work.
    i sent my phone to the shop where i bought it, they said it is caused by my attempts to upgrade to OS to 3.1. But in fact, i never tried upgraded it. as i said, it happenned after my phone battery flat. they said the solution software will only arrive to Malaysia next year. oh my god! they gotta be kidding me!
    so i sent my phone to 3 others independent (not iphone) mobile phone service center and still waiting. now im using back my Dopod 818 phone which luckily i haven't scrap it.
    Please help me, i had enough trouble since i bought it where i wanna try the apple technology

    Iphone has a one year warranty.
    You can take it to the official service provider (you can find this on Apple's website), and if the iphone is defective, then they will replace/repair.
    Did you buy from Maxis? They appear to be the official provider there. They provide service as well.
    http://www.apple.com/my/support/iphone/

  • HT201263 itouch was updating software and failed, now all i have is a screen showing usb plug and itunes logo,cant reset or restore.help

    itouch was updating software and failed, now all i have is a screen showing usb plug and itunes logo,cant reset or restore.help

    Type "unable to restore" into the search bar at the top of this page by Support and read the resulting help article

  • My ipad shows nothing but usb cable and itunes

    My ipad shows the cable and itunes symbol on it and it will not respond to the instructions on here.  Any other ideas?

    You are in Recovery Mode.
    Follow step 1 to 5 closely to recover your iPad.
    http://support.apple.com/kb/HT1808
    Note: You may have to repeat the above a few times

  • HT4890 my ipad just has a pic of a usb plug and Itunes emblem on it what do i do

    help my Ipad wont do anything  
    Thank  you

    The the picture from usb to iTunes on your iPod means that you have to connect your iPod to iTunes on your computer
    And restore the last backup or set it up as a new iPod.

  • Hi, I have a problem with my ipad, I want to restore it but I can not. When I plug the ipad (off) it is not recognized by itunes, I turn the ipad, There are apple and the apple after you see the usb cable and itunes logo for just 1 minute and turns off an

    Hi, I have a problem with my ipad, I want to restore it but I can not. When I plug the ipad (off) it is not recognized by itunes, I turn the ipad, There are apple and the apple after you see the usb cable and itunes logo for just 1 minute and turns off and is no longer recognized by itunes.
    thank you for your help.

    Hi there beni_m,
    You may find the troubleshooting steps in the articles below helpful.
    iOS: Not responding or does not turn on
    http://support.apple.com/kb/ts3281
    iOS: Device not recognized in iTunes for Mac OS X
    http://support.apple.com/kb/ts1591
    iOS: Device not recognized in iTunes for Windows
    http://support.apple.com/kb/ts1538
    -Griff W. 

  • HT4623 when i finished downloading a usb cable and itunes logo appered so i plugged it in the itunes and it said i should take it out from recovery by restoring it.it took 3 hours but at last it didnt download what should i do?

    when i finished downloading a usb cable and itunes logo appered so i plugged it in the itunes and it said i should take it out from recovery by restoring it.it took 3 hours but at last it didnt download what should i do?

    Try holding the home and lock buttons until the iPad reboots. If it does not start up normally, then you will have to restore. To avoid any longer downloads, go to here: http://www.ipswdownloader.com/download-ipad-ipsw-files.php
    and look for your iPad and download the latest firmware. When done downloading, make sure the file is in a easy place to get to. Then, go on iTunes and connect your iPad. Hold your shift key, and press restore. Locate the .ipsw firmware and restore. Make sure no programs are open during the restore proccess as it may interfere.

  • My ipad won't charge.  All I get is picture of white USB cable and iTunes Logo.

    My ipad won't charge.  I must admit, I did use it until there was only 2% power left and then went and plugged directly into power and not through PC... but it won't charge.  All I get is picture of white USB cable, an arrow and the iTunes Logo.  I have turned off and on again as previous posts but all I get is the picture of the USB cable, arrow and iTunes logo.  Please help...

    I have been relatively patient - 3 hours on charge but all it does is show picture of USB cable and itunes logo. It it were charging you would think that a picture of the charge would come up to indicate status of charge - wouldn't you think?

  • I updated to IOS6 on my IPAD 3 and IPad shows a pic of USB port and ITunes but will connect and/or turn on even when I connect to my computer.

    I updated to IOS6 on my IPad and the screen went blank then showed a picture of a USB plug and arrow pointing to ITunes but nothing else happens.  I cannot restore, recover or sync anything....  Please help!

    You will probably need to restore using Recovery Mode. You can read about it here.
    http://support.apple.com/kb/ht4097
    Or you can follow this.
    Recovery Mode Instructions
    Disconnect the USB cable from the iPad, but leave the other end of the cable connected to your computer's USB port.
    Turn off iPad: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for iPad to turn off.
    If you cannot turn off iPad using the slider, press and hold the Sleep/Wake and Home buttons at the same time. When the iPad turns off, release the Sleep/Wake and Home buttons.
    While pressing and holding the Home button, reconnect the USB cable to iPad. When you reconnect the USB cable, iPad should power on.
    Continue holding the Home button until you see the "Connect to iTunes" screen. When this screen appears you can release the Home button.
    If necessary, open iTunes. You should see the recovery mode alert that iTunes has detected an iPad in recovery mode.
    Use iTunes to restore iPad.

  • My iphone4 is stuck in restore mode with usb plug and the itunes symbol on the screen.

    My iphone4 is stuck in restore mode with usb plug and the itunes symbol on the screen after update os7 to os7.04
    My phone is completely disabled, what can i do ?

    Connect to iTunes. The phone is in Recovery mode. Follow the directions in this support document. http://support.apple.com/kb/HT1808

  • I did the iOS 7 seconds update and now my screen is just a plug and iTunes logo.  I don't have a computer anymore just iPad.  What do I do

    I did the iOS 7 seconds update and now my screen is just a plug and iTunes logo.  I don't have a computer anymore just iPad.  What do I do

    Hello,
    My suggestion would be to do the following:
    -Press and hold the power button and home button for the time needed until the screen turns black and the apple logo reappears.
    If that does not work, call the nearest Apple store and ask for assistance.
    Hope this helps,
    TechnologyGuy

  • HT4623 i cannot get past the screen that shows the itunes icon and the usb plug, and my computer wont see my phone

    i cannot get past the screen that shows the itunes icon and the usb plug, and my computer wont see my phone

    Restore the device.

  • HT1473 I recently update my iphone and now is not allowing me to access my contacts, emails etc. When I try to switch it on it has an itunes symbol on the front with the usb plug and an arrow. What do I do to get my contacts etc back and make phone calls?

    I recently update my iphone and now is not allowing me to access my contacts, emails etc. When I try to switch it on it has an itunes symbol on the front with the usb plug and an arrow. What do I do to get my contacts etc back and make phone calls?

    To be more clear:
    Was you phone hacked/jailbroken BEFORE you hooked it up?

  • Iphone 4 froze while doing an update, usb picture and iTunes icon on screen

    tried to update on a iphone 4, however it froze and show a picture of usb port and itunes icon. how do i restore phone

    That screen signifies that the device is in recovery mode. See this support document for instructions on what to do to restore the phone. http://support.apple.com/kb/HT1808

  • Why does my ipad show the usb cord and itunes?

    why does my ipad show the usb cord and itunes?

    It needs to be Connected to iTunes on your Computer.

Maybe you are looking for

  • How to display Excel output in browser instead of client desktop

    Hi, Similar to PDF and Text output, Is it possible to display Excel Output In browser itself. Whenever we try to view the report where the output type is excel, the output opens in Excel Desktop version. We have a requirement where we need the output

  • Choose a programming language

    I want a program that can analyse http://www.youtube.com/browse?s=mr&t=&l=&e=en_US&p=*  (*=1-5) every 10 minutes then pick out  the link that start with http://www.youtube.com/watch?v= export their related information and their links to a form that I

  • I get this message whenever I turn on my printer: The disk you inserted is not readable by this computer. How can I fix this?

    Whenever I turn on my printer (HP OfficeJet Pro L7590), I get an error message that says: "The disk you inserted is not readable by this computer." Then I have to click "ignore" or "eject." I click ignore, and everything works as it should. But the e

  • How to do good Issue with S/N from DI API

    Hai, I want to do good Issue with Serial Number using DI API but I got an error message <b>"\[IGE1.DocEntry]\[line:0],item serial is not found in Whse SR-5155 - 1 - R5155KGS ' (-5002)" </b> here is the code Set oGoodIssue = oCompanyDI.GetBusinessObje

  • Multi-cam doesn't work when I resync

    Hello, I have an hour and a half 3 angled multi-clip to edit. I did not have a TC generator, so what I did was give Aux TC, which has worked perfectly in shorter projects. In this project, I gave Aux TC that start with 2 or 3, so as to avoid "negativ