Ipad 2 stuck in refresh screen and then powers down
I tried to update my apps and when I clicked on update all it went into a black refresh screen and then powers down after a while and then restarts itself into the refresh screen again. I can't seem to get it out of this cycle. Can anyone help me?
Try a Reset...
Reset ( No Data will be Lost )
Press and hold the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears. Release the Buttons.
http://support.apple.com/kb/ht1430
If no joy...
Connect to iTunes on the computer you usually Sync with and “ Restore “...
http://support.apple.com/kb/HT1414
Similar Messages
-
KT2 Combo beeps and then powers down with XP2400
Hi all I could really use some advice here.
I bought an XP2400 Tbred cpu for this system and it never worked. I ended up returning it since it I think it was DOA. But I wanted to confirm it. The 1GHz Duron I have in it runs perfectly.
This system has a 100/133MHz jumper so when I installed the XP2400 I first removed the old 1GHz Duron, I then cleared the bios and set the jumper to 133 and then turned it on. Upon booting up it beeped 2 times VERY quickly and then shut down. One normal beep and one quiet beep you could barely hear but was there. No matter what I tried that's all it would do.
I have an Antec SL350 which does 35 on +5 16 on +12 and 28 on +3.
http://www.antec.com/specs/sl350_spe.html
With only the cpu
2 sticks of 256MB PC133(I tried a single working DDR2100 stick as well)
NO drives connected
and an old PCI video card( I started with my FX5200 but went PCI to test)
I know the mobo supports up to 2600+ 266MHz bus but with the XP2400 it just turned on, never POSTED, beeped and then turned off. My other system, a K7TPro2, is chock full of gear and an XP2000 runs fine with a lesser supply.
Was the xp2400 DOA or is there something amiss in my system? Ie does anyone know what those two short beeps were. If my Power supply is indeed weak what should I go with? A Xp2100? Many thanks for any help here as I need to order a new cpu but I'm afraid I'll run into the same problem if i order another 2400.Wow, thanks for all the quick responses.
Dr Stu, No ,100MHz made no difference and my K7TPro2(not A) would not support it. I have nowhere else to test it so I RMA'd it.
osnavi, as others pointed out its actually a decent power supply. I've seen plently of reports of people running this class and faster CPU on my Power supply, especially considering I stripped the board when I was trying it out. It is of course possible that my Antec has bad CAPS or is dying, but nothing else points to that.
Grayone, nice link. Your right, too bad it never stayed powered up long enough. At best it was one clear beep and part of a 2nd one, but that was it. It powered down within a few seconds every time I turned it on.
My main concern is which cpu to buy. Since this is my HTPC and its running Windows Media Center 2005 I wanted to get the fastest CPU possible. That's why a XP2400 seemed perfect. Now I guess I need to see if I can find an old XP2100 so at least I can cross test it in my other motherboard.
Still though, its always going to bother me that I'll never know if it was my motherboard or the actual CPU that was the problem. Thanks again. -
I have tried a soft reset and uninstalling and reinstalling my email accounts. It crashed when I was trying to refresh my emails and a video emIl came through. Any advice please?
Hello Hobbit80,
Thank you for providing the details of the issue you are experiencing with Mail on your iPhone.
I recommend following these steps for an issue like this (you can skip 4 because it does not relate to the issue you are experiencing and any other steps you may have taken):
If a single application is not responding or stops responding when it opens, you can force it to close.
If the device is unresponsive or if certain controls aren't working as expected, restart your device.
If the device remains unresponsive or does not turn on (or power on),reset your device.
If there is no video or if the screen remains black, verify that the device has enough charge to turn on:
If you are using an iPad, ensure that it's connected to the USB Power Adapter supplied with the device.
Let charge for at least twenty minutes, then see if it starts normally.
If there is no image on the screen, press the Sleep/Wake button to attempt to wake the device.
If the screen displays a red battery icon, continue charging the device until the battery is fully charged.
If the above steps do not resolve the issue, or the if the screen remains black or shows a persistent Apple logo, try restoring with iTunes:
Connect the device to your computer and open iTunes.
If the device appears in iTunes, select and click Restore on the Summary pane. Learn more about restoring iOS software.
If the device doesn't appear in iTunes, try to force the device into recovery mode, and then restore it.
If the above steps do not resolve the issue, contact Apple.
You can find the full article here:
iOS: Not responding or does not turn on
http://support.apple.com/kb/TS3281
If you get to step 5, I recommend backing up your iPhone before performing the restore:
iOS: Back up and restore your iOS device with iCloud or iTunes
http://support.apple.com/kb/HT1766
Thank you for using Apple Support Communities.
Best,
Sheila M. -
I recently received an update option with the iOS 6 for my iphone. After clicking ok, my phone wanted to conect to itunes. After that it wanted me to reset the phone and after all of this was done my iphone had a grey screen and now turns on and off again on its own with out ever going past a grey screen. It will not reconect with itunes of function at all. Please help
http://support.apple.com/kb/HT1808
-
IdeaPad U330 shows a blue screen and then shuts down while trying to Backup using onekey recovery
I have a brand new Lenovo IdeaPad U330 2267-58U preloaded with Windows XP Professional. After I installed some application software I tried to use the Onekey Recovery (from the Start menu) to create a backup of my system partition (C drive) for the first time. For backup mode I chose "Full backup" and for Compression Type I chose "Quick compression" (I tried the no compression option and it didn't work either). I then clicked the "Next" button and left everything unchanged as the default setting (backup location set to the D: drive). As soon as I clicked the "next" button, and then the "start" button, the screen turns blue and the system reboots. The system then reboots with the blue disck-checking screen.
Any fix to this problem?? I haven't been able to create any back up for my system or create a recovery disc so far.have you checked your disk(s) for error(s)?
http://support.microsoft.com/kb/315265/en-us
and one more thing, can you send the system or application events? ( related error )
http://windows.microsoft.com/en-US/windows7/What-information-appears-in-event-logs-Event-Viewer -
When I am on an Internet site, my iPad will suddenly flash a grey screen and then go back to the home screen where I have to start Safari again and reopen my page. It does it frequently sometimes 3 times within 5 minutes. Anyone else have this trouble? It is driving me crazy!
Safari crash regularly
https://discussions.apple.com/thread/2460899?tstart=30 -
I go to play on a game on my iPad it will load the game up and a minute later will go to a blank screen and then back to all my apps.does it everybtime? Why is that? What do I need to do to stop it?
1. Close all inactive apps in the Task Bar. Double-click the Home button and hold apps down for a second or two and tap the minus sign to close app.
2. Try a reset. Hold the Sleep and Home button down for about 10 seconds until you see the Apple Logo -
I just upgraded my ipad to 6.0. I can no longer expand my audio files so that I can move forwards and backwards. I used to get a diagonal arrow to enlarge the screen and then have a bar that I can move to navigate. Can you help?
Hi James,
I am listening to embedded training files on the Quick Time player (I think). They cannot be copied to protect the information. You only have the option of listening. I used to be able to click on the Q in the audio strip and it would provide a diagonal arrow and this would allow me to expand the bar to a full screen. I then had the bar which would allow me to navigate in case I wanted to listen again or in case I wanted to move forward. After my upgrade, I can no longer expand the strip to a full screen with the adjuster. Now I have not chance to take a break in listening to these audios and most of them are at least an hour long. Thanks for your help. -
My iphone 4 got stuck while software update and now it keeps show the apple screen and then shut off
Hey everyone!
My iphone 4 got stuck while I was doing the software update to iOS 6.3.1 without using the computer (directly from the iphone settings) and now it keeps show me the apple screen and then shut off. I really don't know that to do and I would like some help, please!
thank you very much.Backing up, Updating and Restoring
http://support.apple.com/kb/HT1414
Unable to Update or Restore
http://support.apple.com/kb/HT1808 -
My ipad mini 2 gets blue screen and then keep restarting over and over again problem
My ipad mini 2 gets blue screen and then keep restarting over and over again problem. I tried to restore to the factory setting but it was not successful to fix the problem. Sometimes I could not even restore. How can I do with this kind of problem?
I'm very frustrated now. Please help me!I have the same issue and have not found a way to fix it yet. I cant even down grade back to 8.2 because it wont stay on long enough.
-
My ipad mini will not power off, nor will it respond to any commands. The ICloud Backup reminder (which I do not use and have not activated)is stuck on the screen and will not clear.
Hold down the sleep and home keys for about 20 seconds and see if you can get it to reboot.
-
Tuesday night I was texting a friend and when I went to open her message, my screen went blue and restarted. I just wrote it off as weird and went on about my business. Later that night, I tried to turn on my phone and it would not turn on. I plugged it up, held down the power button, and pressed the home button all numerous times. I looked online and it said to do a "hard reset" by holding down the power and home button at the same time--my phone then came on. Throughout Wednesday, it would give me a blue screen and restart--nothing major just really annoying. I took it to the local Verizon store where I bought the phone from and he said that it was some type of hardware defect and I was still under my year warranty so I could get a new one for free--the free phone won't be here until tomorrow, Saturday. I took it home and it didn't give me any trouble for a couple of hours. The next day it was cooperating and then I left town for a little while and it acted up (blue screen and then restarting) a few times. When I got home, it acted up again and so I restarted the phone and it was working fine. A few minutes later, I tried to check my messages and the phone was off again. No matter what I do, my phone will not come back to life. It had at least 45% battery last time I looked at it. I decided to plug the phone up to my computer and see what it did--my computer recognizes that there is a phone hooked to it and it says that it's in "recovery mode". It also said that if I'm having issues with my phone, that I need to reset the phone via iTunes. I guess the questions that arise are
1. Why is my phone doing this?
2. If I reset my phone, will it go back to working again? I ask that because I don't want Verizon to charge me $300 when they send me the replacement phone and I won't need it (assuming that the phone decides to work once it's been reset).
3. What type of hardware defect is this that is causing this issue, not only with my iPhone 5S but others as well?
4. Shouldn't people be notifying Apple and letting them know that they need to fix this issue?
5. Should I report this issue to Apple even though I didn't buy the phone directly from them, but through Verizon?
Any help that anyone could give me would be greatly appreciated! This whole situation has me stressed out and seriously confused.Hi, beth.lau.gr.
Thank you for visiting Apple Support Communities.
I understand you have been experiencing issues with your iPhone restarting and showing you a blue screen. I wont be able to give you an exact answer as to why this is happening. However, this is the most relevant troubleshooting article for this issue. This article also provides options to reach out to us via phone for additional assistance.
If your iOS device restarts, displays the Apple logo, or powers off while you're using it
http://support.apple.com/en-us/HT203899
Cheers,
Jason H. -
HT1338 i cant get in to os system. the screen just stuck in white screen and apple logo
i can not get in to my os system. the screen just stuck in white screen and apple logo
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.
There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.
a. Boot into the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
If you've booted from an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
Step 3
Boot in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is damaged and the drive is probably malfunctioning. In that case, go to step 5.
If you can boot and log in now, empty the Trash, and then open the Finder Info window on your boot volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then reboot as usual (i.e., not in safe mode.)
If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 4
Sometimes a boot failure can be resolved by resetting the NVRAM.
Step 5
Launch Disk Utility in Recovery mode (see Step 1.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then reboot as usual.
Step 6
Reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 7
Repeat step 6, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a backup.
Step 8
A dead logic-board battery in a Mac Pro can cause a gray screen at boot. Typically the boot failure will be preceded by loss of the startup disk and system clock settings. See the user manual for replacement instructions.
Step 9
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store to have the machine tested. -
my IPAD 4 is not working properly. it will blink and then shut down even when the battery is charged. i have done several reset on the iad. what do i do , i need help
iOS: Device unexpectedly restarts, displays Apple logo, or powers off
http://support.apple.com/kb/TS5356
Cheers, Tom -
My ipad has a black screen and the apple logo and won't do anything else. I have tried to reset to no avail.
Try and force iPad into Recovery Mode
1. Disconnect the USB cable from the device, but leave the other end of the cable connected to your computer's USB port.
2. Turn off the device: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for the device to turn off.
3.While pressing and holding the Home button, reconnect the USB cable to the device. The device should turn on.
4. Continue holding the Home button until you see the "Connect to iTunes" screen. When this screen appears, release the Home button. iTunes should alert you that it has detected a device in recovery mode. Click OK, and then click Restore to restore the device.
Note: Data will be lost. You may have to repeat the above many times.
Maybe you are looking for
-
I can't open an image in Firefox, please help..
I am using Firefox 11 UK edition on a HP Laptop running Windows 7. I like to view images in FF instead of Micro-craps image viewer programs. Until recently I had no problem with that. I would right click on the image and select open with FF. Today al
-
Exit for checking Exchange Rate in ME21N(Only for Import PO)
Hi, Could you pls tel me User Exit/BADI for transaction ME21N to check the Exch Rate Fixed In Delivery/Invoice tab for Import Document Type. Thanks in Advance.. Nithy
-
Toolbar in alv display using oops alv
i have written code for displaying toolbar in alv display using oops, but it is not displaying please find the below code and let me know reason. *& Report ZTRANSFER_ORDER2 * REPORT ZTRANSFER_ORDER2 . *&
-
In Order to improve navigation of my Share point list I need drop down filter web part. How can I make one? Is there an out of the box Filter web part to provide that function? I used Choice Filter web part that is not exactly do what I need.
-
Adobe Application Mgr crashes constantly ...
hi ... I've got a 2009 Macbook Pro laptop with an intel dual core 64-bit + 4 gig RAM. in Lion OS, the Adobe application manager crashed every time i started it. I've now upgraded to the latest OS, "Mountain Lion", with all updates; I trashed AAM & r