IPad 2 VPN issues

Why is my iPad suddenly requesting I install VPN Defender to view websites?

@ Steve Wallis: Hmm, right, I also used to have the same problem with mine. What VPN you are using to connect your 3GS and iPad with?
I have wasted hundreds of $$$ on finding which is the best VPN that will work with my iPad and iPad 2 along with all the other devices which I might have in future also. But, none all of them worked out, however, I took help from a very informative site and, can refer you to the list of top 5 100% working (with all devices) ipad VPN list, I am sure this will help you out.

Similar Messages

  • Connect iPad VPN to RV220W?

    What is the best way to connect an iPad VPN client to access an RV220W?
    Sent from Cisco Technical Support iPad App

    Jags@GSC wrote:
    It appears that my pix515 running at ver 7 might be the issue.
    You didn't bother to mention that you had an issue.  You still haven't explained what you "issue" is. Maybe you should try contacting Cisco support.

  • Remote access Vpn issue

    Dear All,
    I have configured remote access vpn without using split tunnel.Everything is working fine.I can access all the inside network which is allowed in acl.
    I am facing strange issue now. I have created a pool for remote access vpn with a range 192.168.5.8/29.I can access my internal subnets 10.10.0.0/16.
    I have below acess-list for acl-in.
    access-list acl-in extended permit ip object-group vpnclients 192.168.5.8 255.255.255.248
    object-group network vpnclients
    network-object host 10.110.100.26
    network-object host 10.106.100.15
    network-object host 10.10.10.6
    network-object host 10.10.20.82
    network-object host 10.110.100.48
    network-object host 10.10.20.53
    network-object host 10.10.20.54
    network-object host 10.60.100.1
    network-object host 10.10.10.75
    network-object host 10.10.20.100
    network-object host 10.10.130.136
    network-object host 10.106.100.16
    network-object host 10.106.100.9
    network-object host 10.170.100.1
    network-object host 10.170.100.2
    network-object host 10.170.100.21
    network-object host 10.101.100.20
    network-object host 10.170.100.25
    So whichever IPs i have called in vpnclient group is able to access via RA vpn.Issue is when i try to access internal network of 192.168.198.0/24, i am able to access it without adding in vpnclient group. Even for 192.168.197.0/24,192.168.197.0/24 the same. But for 10.10.0.0/16 we can access only after adding in vpnclient group. Any one has face this issue before. Is this because of same network i mean 192.168.0.0 something like that.There is no other staement in acl-in for 192.168.0.0
    Regards
    -Danesh Ahammad

    Hi,
    If i read correctly you made the RA vpn "without"  split tunnel, correct? if that is the case, all of the traffic will traverse the vpn connection (tunnel all) , the access-list "acl-in" is of no use to it.
    try converting it to use split tunnel, i am sure that way you can not access resources that are not mentioned in the list.
    ~Harry

  • Any ideas how to better troubleshoot VPN issue?

    Hi,
    I've recently upgraded my WLAN router to a brand new AVM FRITZ!Box WLAN 7390, in part for its VPN capabilities.
    So far, I've been unable to create a working connection.
    AVM's VPN is based on Cisco IPSec, and they provide a step-by-step procedure on how configure a Mac-based VPN connection (http://www.avm.de/de/Service/Service-Portale/Service-Portal/VPN_Interoperabilita et/16206.php - unfortunately only available in German, sorry). Following it, I still can't get it to work. Contacting their support I got first the same procedure and after pointing out I already followed it a "we don't support other vendors".
    Funny enough, I got a second VPN connection to my work's VPN server just fine, though admittedly there we have a true Cisco box.
    My initial setup was based on a 192.x.x.x net on my AVM, I could establish a VPN connection but coudn't ping/ssh/http/you-name-the-protocol in either direction. Our companies net is a 10.x.x.x net so, and as I have also VMware fusion running on my Mac with DHCP enabled on a different 192.x.x.x net plus a third 192.x.x.x net from my Wifi access I decided to reconfigure my AVM net to a 172.x.x.x net and stop VMware services for the tests (ie simplify as much as I could to help troubleshoot).
    Alas, instead of being able to establish a non-working VPN connection, now I ain't able to get the tunnel up. IKE Phase 1 completes but Phase 2 doesn't.
    Here's the relevant section from kernel.log:
    Dec 30 11:47:57 jupiter configd[16]: IPSec connecting to server <myservernameismybusiness>.dyndns.info
    Dec 30 11:47:57 jupiter configd[16]: SCNC: start, triggered by SystemUIServer, type IPSec, status 0
    Dec 30 11:47:57 jupiter configd[16]: IPSec Phase1 starting.
    Dec 30 11:47:57 jupiter racoon[1910]: IPSec connecting to server 77.x.x.x
    Dec 30 11:47:57 jupiter racoon[1910]: Connecting.
    Dec 30 11:47:57 jupiter racoon[1910]: IPSec Phase1 started (Initiated by me).
    Dec 30 11:47:57 jupiter racoon[1910]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 1).
    Dec 30 11:47:58 jupiter racoon[1910]: IKEv1 Phase1 AUTH: success. (Initiator, Aggressive-Mode Message 2).
    Dec 30 11:47:58 jupiter racoon[1910]: IKE Packet: receive success. (Initiator, Aggressive-Mode message 2).
    Dec 30 11:47:58 jupiter racoon[1910]: IKEv1 Phase1 Initiator: success. (Initiator, Aggressive-Mode).
    Dec 30 11:47:58 jupiter racoon[1910]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 3).
    Dec 30 11:47:58 jupiter racoon[1910]: IKE Packet: transmit success. (Information message).
    Dec 30 11:47:58 jupiter racoon[1910]: IKEv1 Information-Notice: transmit success. (ISAKMP-SA).
    Dec 30 11:47:58 jupiter racoon[1910]: IPSec Phase1 established (Initiated by me).
    Dec 30 11:47:58 jupiter racoon[1910]: IPSec Extended Authentication requested.
    Dec 30 11:47:58 jupiter configd[16]: IPSec requesting Extended Authentication.
    Dec 30 11:48:01 jupiter configd[16]: IPSec sending Extended Authentication.
    Dec 30 11:48:01 jupiter racoon[1910]: IKE Packet: transmit success. (Mode-Config message).
    Dec 30 11:48:01 jupiter racoon[1910]: IPSec Extended Authentication sent.
    Dec 30 11:48:02 jupiter racoon[1910]: IKEv1 XAUTH: success. (XAUTH Status is OK).
    Dec 30 11:48:02 jupiter racoon[1910]: IPSec Extended Authentication Passed.
    Dec 30 11:48:02 jupiter racoon[1910]: IKE Packet: transmit success. (Mode-Config message).
    Dec 30 11:48:02 jupiter racoon[1910]: IKEv1 Config: retransmited. (Mode-Config retransmit).
    Dec 30 11:48:02 jupiter racoon[1910]: IPSec Network Configuration requested.
    Dec 30 11:48:03 jupiter racoon[1910]: IPSec Network Configuration established.
    Dec 30 11:48:03 jupiter racoon[1910]: IKE Packet: receive success. (MODE-Config).
    Dec 30 11:48:03 jupiter configd[16]: IPSec Network Configuration started.
    Dec 30 11:48:03 jupiter configd[16]: IPSec Network Configuration: INTERNAL-IP4-ADDRESS = 172.77.7.14.
    Dec 30 11:48:03 jupiter configd[16]: IPSec Network Configuration: SAVE-PASSWORD = 1.
    Dec 30 11:48:03 jupiter configd[16]: IPSec Network Configuration: DEFAULT-ROUTE = local-address 172.77.7.14/32.
    Dec 30 11:48:03 jupiter configd[16]: host_gateway: write routing socket failed, command 2, No such process
    Dec 30 11:48:03 jupiter configd[16]: IPSec Phase2 starting.
    Dec 30 11:48:03 jupiter configd[16]: IPSec Network Configuration established.
    Dec 30 11:48:03 jupiter configd[16]: IPSec Phase1 established.
    Dec 30 11:48:03 jupiter configd[16]: event_callback: Address added. previous interface setting (name: en1, address: 192.168.43.242), current interface setting (name: utun0, family: 1001, address: 172.77.7.14, subnet: 255.255.255.255, destination: 172.77.7.14).
    Dec 30 11:48:03 jupiter racoon[1910]: IPSec Phase2 started (Initiated by me).
    Dec 30 11:48:03 jupiter racoon[1910]: IKE Packet: transmit success. (Initiator, Quick-Mode message 1).
    Dec 30 11:48:03 jupiter configd[16]: network configuration changed.
    Dec 30 11:48:03 jupiter configd[16]: IPSec port-mapping update for en1 ignored: VPN is the Primary interface. Public Address: ac4d070e, Protocol: None, Private Port: 0, Public Port: 0
    Dec 30 11:48:03 jupiter configd[16]:
    Dec 30 11:48:03 jupiter configd[16]: setting hostname to "jupiter.local"
    Dec 30 11:48:03 jupiter racoon[1910]: IKE Packet: receive success. (Information message).
    Dec 30 11:48:06 jupiter racoon[1910]: IKE Packet: transmit success. (Phase2 Retransmit).
    Dec 30 11:48:07 jupiter racoon[1910]: IKE Packet: receive success. (Information message).
    Dec 30 11:48:09 jupiter racoon[1910]: IKE Packet: transmit success. (Phase2 Retransmit).
    Dec 30 11:48:09 jupiter racoon[1910]: IKE Packet: receive success. (Information message).
    Dec 30 11:48:12 jupiter racoon[1910]: IKE Packet: transmit success. (Phase2 Retransmit).
    Dec 30 11:48:13 jupiter racoon[1910]: IKE Packet: receive success. (Information message).
    Dec 30 11:48:15 jupiter racoon[1910]: IKE Packet: transmit success. (Phase2 Retransmit).
    Dec 30 11:48:15 jupiter racoon[1910]: IKE Packet: receive success. (Information message).
    Dec 30 11:48:18 jupiter racoon[1910]: IKE Packet: transmit success. (Phase2 Retransmit).
    Dec 30 11:48:18 jupiter racoon[1910]: IKE Packet: receive success. (Information message).
    Dec 30 11:48:21 jupiter racoon[1910]: IKE Packet: transmit success. (Phase2 Retransmit).
    Dec 30 11:48:21 jupiter racoon[1910]: IKE Packet: receive success. (Information message).
    Dec 30 11:48:24 jupiter racoon[1910]: IKE Packet: transmit success. (Phase2 Retransmit).
    Dec 30 11:48:25 jupiter racoon[1910]: IKE Packet: receive success. (Information message).
    Dec 30 11:48:27 jupiter racoon[1910]: IKE Packet: transmit success. (Phase2 Retransmit).
    Dec 30 11:48:27 jupiter racoon[1910]: IKE Packet: receive success. (Information message).
    Dec 30 11:48:30 jupiter racoon[1910]: IKE Packet: transmit success. (Phase2 Retransmit).
    Dec 30 11:48:30 jupiter racoon[1910]: IKE Packet: receive success. (Information message).
    Dec 30 11:48:33 jupiter configd[16]: IPSec disconnecting from server 77.x.x.x
    Dec 30 11:48:33 jupiter racoon[1910]: IPSec disconnecting from server 77.x.x.x
    Dec 30 11:48:33 jupiter racoon[1910]: IKE Packet: transmit success. (Information message).
    Dec 30 11:48:33 jupiter racoon[1910]: IKEv1 Information-Notice: transmit success. (Delete ISAKMP-SA).
    Dec 30 11:48:33 jupiter configd[16]: SCNC Controller: service_ending_verify_primaryservice, waiting for PrimaryService. status = 1
    Dec 30 11:48:33 jupiter configd[16]:
    Dec 30 11:48:33 jupiter configd[16]: network configuration changed.
    Dec 30 11:48:33 jupiter configd[16]: SCNC Controller: ipv4_state_changed, done waiting for ServiceID.
    Dec 30 11:48:33 jupiter configd[16]:
    Dec 30 11:48:33 jupiter configd[16]: setting hostname to "jupiter"
    When connecting to my work-place it looks like:
    Dec 30 12:33:14 jupiter configd[16]: IPSec connecting to server <mycompanyismybusiness>.ch
    Dec 30 12:33:14 jupiter configd[16]: SCNC: start, triggered by SystemUIServer, type IPSec, status 0
    Dec 30 12:33:14 jupiter configd[16]: IPSec Phase1 starting.
    Dec 30 12:33:14 jupiter racoon[1976]: IPSec connecting to server 62.x.x.x
    Dec 30 12:33:14 jupiter racoon[1976]: Connecting.
    Dec 30 12:33:14 jupiter racoon[1976]: IPSec Phase1 started (Initiated by me).
    Dec 30 12:33:14 jupiter racoon[1976]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 1).
    Dec 30 12:33:14 jupiter racoon[1976]: IKEv1 Phase1 AUTH: success. (Initiator, Aggressive-Mode Message 2).
    Dec 30 12:33:14 jupiter racoon[1976]: IKE Packet: receive success. (Initiator, Aggressive-Mode message 2).
    Dec 30 12:33:14 jupiter racoon[1976]: IKEv1 Phase1 Initiator: success. (Initiator, Aggressive-Mode).
    Dec 30 12:33:14 jupiter racoon[1976]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 3).
    Dec 30 12:33:14 jupiter racoon[1976]: IPSec Phase1 established (Initiated by me).
    Dec 30 12:33:15 jupiter racoon[1976]: IPSec Extended Authentication requested.
    Dec 30 12:33:15 jupiter configd[16]: IPSec requesting Extended Authentication.
    Dec 30 12:33:21 jupiter configd[16]: IPSec sending Extended Authentication.
    Dec 30 12:33:21 jupiter racoon[1976]: IKE Packet: transmit success. (Mode-Config message).
    Dec 30 12:33:21 jupiter racoon[1976]: IPSec Extended Authentication sent.
    Dec 30 12:33:21 jupiter racoon[1976]: IKEv1 XAUTH: success. (XAUTH Status is OK).
    Dec 30 12:33:21 jupiter racoon[1976]: IPSec Extended Authentication Passed.
    Dec 30 12:33:21 jupiter racoon[1976]: IKE Packet: transmit success. (Mode-Config message).
    Dec 30 12:33:21 jupiter racoon[1976]: IKEv1 Config: retransmited. (Mode-Config retransmit).
    Dec 30 12:33:21 jupiter racoon[1976]: IPSec Network Configuration requested.
    Dec 30 12:33:21 jupiter racoon[1976]: IPSec Network Configuration established.
    Dec 30 12:33:21 jupiter racoon[1976]: IKE Packet: receive success. (MODE-Config).
    Dec 30 12:33:21 jupiter configd[16]: IPSec Network Configuration started.
    Dec 30 12:33:21 jupiter configd[16]: IPSec Network Configuration: INTERNAL-IP4-ADDRESS = 10.100.1.18.
    Dec 30 12:33:21 jupiter configd[16]: IPSec Network Configuration: INTERNAL-IP4-MASK = 255.255.255.0.
    Dec 30 12:33:21 jupiter configd[16]: IPSec Network Configuration: SAVE-PASSWORD = 1.
    Dec 30 12:33:21 jupiter configd[16]: IPSec Network Configuration: INTERNAL-IP4-DNS = 10.100.1.129.
    Dec 30 12:33:21 jupiter configd[16]: IPSec Network Configuration: SPLIT-INCLUDE.
    Dec 30 12:33:21 jupiter configd[16]: IPSec Network Configuration: DEF-DOMAIN = iw.local.
    Dec 30 12:33:21 jupiter configd[16]: host_gateway: write routing socket failed, command 2, No such process
    Dec 30 12:33:21 jupiter configd[16]: installed route: (address 10.100.1.0, gateway 10.100.1.18)
    Dec 30 12:33:21 jupiter configd[16]: IPSec Phase2 starting.
    Dec 30 12:33:21 jupiter racoon[1976]: IPSec Phase2 started (Initiated by me).
    Dec 30 12:33:21 jupiter racoon[1976]: IKE Packet: transmit success. (Initiator, Quick-Mode message 1).
    Dec 30 12:33:21 jupiter configd[16]: IPSec Network Configuration established.
    Dec 30 12:33:21 jupiter configd[16]: IPSec Phase1 established.
    Dec 30 12:33:21 jupiter configd[16]: event_callback: Address added. previous interface setting (name: en1, address: 192.168.43.242), current interface setting (name: utun0, family: 1001, address: 10.100.1.18, subnet: 255.255.255.0, destination: 10.100.1.18).
    Dec 30 12:33:21 jupiter configd[16]: network configuration changed.
    Dec 30 12:33:21 jupiter racoon[1976]: IKE Packet: receive success. (Initiator, Quick-Mode message 2).
    Dec 30 12:33:21 jupiter racoon[1976]: IKE Packet: transmit success. (Initiator, Quick-Mode message 3).
    Dec 30 12:33:21 jupiter racoon[1976]: IKEv1 Phase2 Initiator: success. (Initiator, Quick-Mode).
    Dec 30 12:33:21 jupiter racoon[1976]: IPSec Phase2 established (Initiated by me).
    Dec 30 12:33:21 jupiter configd[16]: IPSec Phase2 established.
    An earlies test in a Starbucks around here had the same result, during looking at the netstat -nr output I found I got onto a 10.x.x.x net on the Wifi and still could connect to the (different) 10.x.x.x net at work.
    My TCP/IP Networking course was around 2000, but the default route seen in the non-working log section looks like bullsh*t to me anyhow: DEFAULT-ROUTE = local-address 172.77.7.14/32
    On the other hand, the Phase 2 message seem to indicate a different mode for Phase 2 between the working and the non-working one.
    This is from the exported config of my AVM box:
    **** CFGFILE:vpn.cfg
    * /var/flash/vpn.cfg
    * Wed Dec 28 16:01:09 2011
    vpncfg {
            connections {
                    enabled = yes;
                    conn_type = conntype_user;
                    name = "[email protected]";
                    always_renew = no;
                    reject_not_encrypted = no;
                    dont_filter_netbios = yes;
                    localip = 0.0.0.0;
                    local_virtualip = 0.0.0.0;
                    remoteip = 0.0.0.0;
                    remote_virtualip = 172.77.7.14;
                    remoteid {
                            key_id = "<mykeyismybusiness>";
                    mode = phase1_mode_aggressive;
                    phase1ss = "all/all/all";
                    keytype = connkeytype_pre_shared;
                    key = "<mykeyismybusiness>";
                    cert_do_server_auth = no;
                    use_nat_t = no;
                    use_xauth = yes;
                    xauth {
                            valid = yes;
                            username = "<myuserismybusiness>";
                            passwd = "<mypasswordismybusiness>";
                    use_cfgmode = no;
                    phase2localid {
                            ipnet {
                                    ipaddr = 0.0.0.0;
                                    mask = 0.0.0.0;
                    phase2remoteid {
                            ipaddr = 172.22.7.14;
                    phase2ss = "esp-all-all/ah-none/comp-all/no-pfs";
                    accesslist =
                                 "permit ip 172.22.7.0 255.255.255.240 172.22.7.14 255.255.255.255";
            ike_forward_rules = "udp 0.0.0.0:500 0.0.0.0:500",
                                "udp 0.0.0.0:4500 0.0.0.0:4500";
    // EOF
    **** END OF FILE ****
    I also noticed an extra "IPSec port-mapping update for en1 ignored" message in the non-working log section, but I'm not sure a) how significant that might be, and b) how to find out what the ignored update might have been to decide whether not ignoring it would help.
    A quick test with the AnyConnect Client from Cisco didn't help either, apparently it establishes an https connection first as I got a window which certificate details from my QNAP behind the AVM Box (I got a port forward for https to it)
    So I'm looking for any ideas how to better troubleshoot this VPN issue...
    Many thanks in advance!
    BR,
    Alex

    Ok, found a small typo in my config (had at one point a 172.77.7.14 instead of the 172.22.7.14), no I can also connect from the 172.x.x.x net but still no ping etc. The relevant section of the log looks now like this:
    Dec 30 16:44:27 jupiter configd[16]: IPSec connecting to server <myservernameismybusiness>.dyndns.info
    Dec 30 16:44:27 jupiter configd[16]: SCNC: start, triggered by SystemUIServer, type IPSec, status 0
    Dec 30 16:44:28 jupiter configd[16]: IPSec Phase1 starting.
    Dec 30 16:44:28 jupiter racoon[2183]: IPSec connecting to server 77.x.x.x
    Dec 30 16:44:28 jupiter racoon[2183]: Connecting.
    Dec 30 16:44:28 jupiter racoon[2183]: IPSec Phase1 started (Initiated by me).
    Dec 30 16:44:28 jupiter racoon[2183]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 1).
    Dec 30 16:44:28 jupiter racoon[2183]: IKEv1 Phase1 AUTH: success. (Initiator, Aggressive-Mode Message 2).
    Dec 30 16:44:28 jupiter racoon[2183]: IKE Packet: receive success. (Initiator, Aggressive-Mode message 2).
    Dec 30 16:44:28 jupiter racoon[2183]: IKEv1 Phase1 Initiator: success. (Initiator, Aggressive-Mode).
    Dec 30 16:44:28 jupiter racoon[2183]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 3).
    Dec 30 16:44:28 jupiter racoon[2183]: IKE Packet: transmit success. (Information message).
    Dec 30 16:44:28 jupiter racoon[2183]: IKEv1 Information-Notice: transmit success. (ISAKMP-SA).
    Dec 30 16:44:28 jupiter racoon[2183]: IPSec Phase1 established (Initiated by me).
    Dec 30 16:44:28 jupiter racoon[2183]: IPSec Extended Authentication requested.
    Dec 30 16:44:28 jupiter configd[16]: IPSec requesting Extended Authentication.
    Dec 30 16:44:31 jupiter configd[16]: IPSec sending Extended Authentication.
    Dec 30 16:44:31 jupiter racoon[2183]: IKE Packet: transmit success. (Mode-Config message).
    Dec 30 16:44:31 jupiter racoon[2183]: IPSec Extended Authentication sent.
    Dec 30 16:44:32 jupiter racoon[2183]: IKEv1 XAUTH: success. (XAUTH Status is OK).
    Dec 30 16:44:32 jupiter racoon[2183]: IPSec Extended Authentication Passed.
    Dec 30 16:44:32 jupiter racoon[2183]: IKE Packet: transmit success. (Mode-Config message).
    Dec 30 16:44:32 jupiter racoon[2183]: IKEv1 Config: retransmited. (Mode-Config retransmit).
    Dec 30 16:44:32 jupiter racoon[2183]: IPSec Network Configuration requested.
    Dec 30 16:44:33 jupiter racoon[2183]: IPSec Network Configuration established.
    Dec 30 16:44:33 jupiter racoon[2183]: IKE Packet: receive success. (MODE-Config).
    Dec 30 16:44:33 jupiter configd[16]: IPSec Network Configuration started.
    Dec 30 16:44:33 jupiter configd[16]: IPSec Network Configuration: INTERNAL-IP4-ADDRESS = 172.22.7.14.
    Dec 30 16:44:33 jupiter configd[16]: IPSec Network Configuration: SAVE-PASSWORD = 1.
    Dec 30 16:44:33 jupiter configd[16]: IPSec Network Configuration: INTERNAL-IP4-DNS = 172.22.7.1.
    Dec 30 16:44:33 jupiter configd[16]: IPSec Network Configuration: DEFAULT-ROUTE = local-address 172.22.7.14/32.
    Dec 30 16:44:33 jupiter configd[16]: host_gateway: write routing socket failed, command 2, No such process
    Dec 30 16:44:33 jupiter configd[16]: IPSec Phase2 starting.
    Dec 30 16:44:33 jupiter racoon[2183]: IPSec Phase2 started (Initiated by me).
    Dec 30 16:44:33 jupiter racoon[2183]: IKE Packet: transmit success. (Initiator, Quick-Mode message 1).
    Dec 30 16:44:33 jupiter configd[16]: IPSec Network Configuration established.
    Dec 30 16:44:33 jupiter configd[16]: IPSec Phase1 established.
    Dec 30 16:44:33 jupiter configd[16]: event_callback: Address added. previous interface setting (name: en1, address: 192.168.43.242), current interface setting (name: utun0, family: 1001, address: 172.22.7.14, subnet: 255.255.255.255, destination: 172.22.7.14).
    Dec 30 16:44:33 jupiter configd[16]: network configuration changed.
    Dec 30 16:44:33 jupiter racoon[2183]: IKE Packet: receive success. (Initiator, Quick-Mode message 2).
    Dec 30 16:44:33 jupiter racoon[2183]: IKE Packet: transmit success. (Initiator, Quick-Mode message 3).
    Dec 30 16:44:33 jupiter racoon[2183]: IKEv1 Phase2 Initiator: success. (Initiator, Quick-Mode).
    Dec 30 16:44:33 jupiter racoon[2183]: IPSec Phase2 established (Initiated by me).
    Dec 30 16:44:33 jupiter configd[16]: IPSec Phase2 established.
    Dec 30 16:44:43 jupiter racoon[2183]: IKE Packet: receive failed. (MODE-Config).
    Dec 30 16:44:48 jupiter racoon[2183]: IKE Packet: transmit success. (Information message).
    Dec 30 16:44:48 jupiter racoon[2183]: IKEv1 Information-Notice: transmit success. (R-U-THERE?).
    Dec 30 16:44:48 jupiter racoon[2183]: IKEv1 Dead-Peer-Detection: request transmitted. (Initiator DPD Request).
    Dec 30 16:44:48 jupiter racoon[2183]: IKEv1 Dead-Peer-Detection: response received. (Initiator DPD Response).
    Dec 30 16:44:48 jupiter racoon[2183]: IKE Packet: receive success. (Information message).
    Dec 30 16:45:03 jupiter configd[16]: setting hostname to "jupiter.local"
    followed by lots of:
    Dec 30 16:45:03 jupiter racoon[2183]: IKE Packet: receive failed. (MODE-Config).
    Dec 30 16:45:08 jupiter racoon[2183]: IKE Packet: transmit success. (Information message).
    Dec 30 16:45:08 jupiter racoon[2183]: IKEv1 Information-Notice: transmit success. (R-U-THERE?).
    Dec 30 16:45:08 jupiter racoon[2183]: IKEv1 Dead-Peer-Detection: request transmitted. (Initiator DPD Request).
    Dec 30 16:45:08 jupiter racoon[2183]: IKEv1 Dead-Peer-Detection: response received. (Initiator DPD Response).
    Dec 30 16:45:08 jupiter racoon[2183]: IKE Packet: receive success. (Information message).
    Dec 30 16:45:28 jupiter racoon[2183]: IKE Packet: transmit success. (Information message).
    Dec 30 16:45:28 jupiter racoon[2183]: IKEv1 Information-Notice: transmit success. (R-U-THERE?).
    Dec 30 16:45:28 jupiter racoon[2183]: IKEv1 Dead-Peer-Detection: request transmitted. (Initiator DPD Request).
    Dec 30 16:45:29 jupiter racoon[2183]: IKEv1 Dead-Peer-Detection: response received. (Initiator DPD Response).
    Dec 30 16:45:29 jupiter racoon[2183]: IKE Packet: receive success. (Information message).
    Dec 30 16:45:49 jupiter racoon[2183]: IKE Packet: transmit success. (Information message).
    Dec 30 16:45:49 jupiter racoon[2183]: IKEv1 Information-Notice: transmit success. (R-U-THERE?).
    Dec 30 16:45:49 jupiter racoon[2183]: IKEv1 Dead-Peer-Detection: request transmitted. (Initiator DPD Request).
    Dec 30 16:45:50 jupiter racoon[2183]: IKEv1 Dead-Peer-Detection: response received. (Initiator DPD Response).
    Dec 30 16:45:50 jupiter racoon[2183]: IKE Packet: receive success. (Information message).
    Dec 30 16:46:10 jupiter racoon[2183]: IKE Packet: transmit success. (Information message).
    Dec 30 16:46:10 jupiter racoon[2183]: IKEv1 Information-Notice: transmit success. (R-U-THERE?).
    Dec 30 16:46:10 jupiter racoon[2183]: IKEv1 Dead-Peer-Detection: request transmitted. (Initiator DPD Request).
    Dec 30 16:46:10 jupiter racoon[2183]: IKEv1 Dead-Peer-Detection: response received. (Initiator DPD Response).
    Dec 30 16:46:10 jupiter racoon[2183]: IKE Packet: receive success. (Information message).
    Dec 30 16:46:30 jupiter racoon[2183]: IKE Packet: transmit success. (Information message).
    Dec 30 16:46:30 jupiter racoon[2183]: IKEv1 Information-Notice: transmit success. (R-U-THERE?).
    Dec 30 16:46:30 jupiter racoon[2183]: IKEv1 Dead-Peer-Detection: request transmitted. (Initiator DPD Request).
    Dec 30 16:46:30 jupiter racoon[2183]: IKEv1 Dead-Peer-Detection: response received. (Initiator DPD Response).
    Dec 30 16:46:30 jupiter racoon[2183]: IKE Packet: receive success. (Information message).

  • SAPGUI Java 7.20 Rev 6 download and VPN issue

    Dear SAP friends please help.
    We are trying to connect to SAP via a Mac running Lion and a VPN with SAPGUI for Java Rev 5. We get the logon successfully but never get further than the licence message. We have updated to the latest Java and also tried it in 32 bitz mode. We are unable to download the latest Rev 6 (due to my user authorisation) but we still think this is a VPN issue. Can you please help? I enclose the trace which shows the point at which is stops.
    Many thanks
    Andrew
    16.11. 17:36:05.118 CALL:     <CONTROL SHELLID="101">
    16.11. 17:36:05.118 CALL:       <PROPERTY VALUE="0" NAME="120"/>
    16.11. 17:36:05.118 CALL:       <PROPERTY VALUE="0" NAME="300"/>
    16.11. 17:36:05.118 CALL:     </CONTROL>
    16.11. 17:36:05.118 CALL:   </CONTROLS>
    16.11. 17:36:05.118 CALL:   <COPY id="copy">
    16.11. 17:36:05.118 CALL:     <GUI id="gui">
    16.11. 17:36:05.118 CALL:       <METRICS id="metrics" X3="1440" X2="7" X1="7" X0="283" Y3="900" Y2="20" Y1="12" Y0="283"/>
    16.11. 17:36:05.118 CALL:     </GUI>
    16.11. 17:36:05.118 CALL:   </COPY>
    16.11. 17:36:05.118 CALL: </DATAMANAGER>
    16.11. 17:36:05.119 CALL: Call 1042: #3#.setMoreDataIndicator(true);
    16.11. 17:36:05.122 CON: GuiNiNetConnection: sending DIAG data to writer thread for modus 0
    ERROR #############################
    16.11. 17:37:10.018 ERROR: GuiNiReaderThread: read failed: Error: connection to partner '172.23.200.109:3200' broken
    16.11. 17:37:10.018 ERROR: 
    16.11. 17:37:10.018 ERROR: Wed Nov 16 17:37:10 2011
    16.11. 17:37:10.018 ERROR: Release 720
    16.11. 17:37:10.018 ERROR: Component NI (network interface), version 40
    16.11. 17:37:10.018 ERROR: rc = -6, module nixxi.cpp, line 5087
    16.11. 17:37:10.018 ERROR: Detail NiIRead: P=172.23.200.109:3200; L=10.64.10.112:53387
    16.11. 17:37:10.018 ERROR: System Call recv
    16.11. 17:37:10.018 ERROR: Error No 60
    16.11. 17:37:10.018 ERROR: 'Operation timed out'
    ERROR #############################
    16.11. 17:37:10.018 CON: -
    16.11. 17:37:10.018 CON: GuiNiNetConnection: sending DIAG data to connection for modus -1
    ERROR #############################
    16.11. 17:37:10.234 ERROR: GuiConnection: Connection closed
    16.11. 17:37:10.234 ERROR: Error: connection to partner '172.23.200.109:3200' broken
    16.11. 17:37:10.234 ERROR: 
    16.11. 17:37:10.234 ERROR: Wed Nov 16 17:37:10 2011
    16.11. 17:37:10.234 ERROR: Release 720
    16.11. 17:37:10.234 ERROR: Component NI (network interface), version 40
    16.11. 17:37:10.234 ERROR: rc = -6, module nixxi.cpp, line 5087
    16.11. 17:37:10.234 ERROR: Detail NiIRead: P=172.23.200.109:3200; L=10.64.10.112:53387
    16.11. 17:37:10.234 ERROR: System Call recv
    16.11. 17:37:10.234 ERROR: Error No 60
    16.11. 17:37:10.234 ERROR: 'Operation timed out'
    ERROR #############################
    ERROR #############################

    Hello Andrew,
    some version of the VPN client on Lion seems to have a known issue according to SAP internal discussions.
    I found someone telling, that with F5 SSL VPN Plugin 7000.2011.0907.01, it is working again.
    It seems to be available from https://connectfp.sap.com.
    For uninstalling old F5 version, see http://support.f5.com/kb/en-us/solutions/public/3000/800/sol3826.html
    (many "seems", because I am still on Snow Leopard and can not talk about this issue from my own experience)
    Regarding user authorization for downloading software in Service MarketPlace, please refer to [note 1037574|https://service.sap.com/sap/support/notes/1037574].
    Best regards
    Rolf-Martin

  • Best ressources for "ANDROID vs IPAD video issues"

    Hello
    Would someone be kind enough to post here the best ressources for the "ANDROID vs IPAD VIDEOS issues" ?
    I got lots of troubles to have some videos working on Samsung Galaxytab ...
    thanx !

    mm  well
    Sorry but what is the definition of "inline" videos, I wanna be really sure (i'm not english / in my language my videos are "inline" videos: videos put inside the document).)
    On some apps I made, some videos work, some don't. And
    one of the main issues are
    - they launch full screen when they're not supposed to (i want them to launch in a definite area)
    - they dont launch full screen when they're supposed to (when they're suppposed to play in full screen, they just do not appear: black screen)
    mmm ?

  • Airport Extreme 802.11n New Firmware Release (VPN ISSUE)

    The info accompanying the release of today's firmware upgrade makes no mention of a fix to the VPN problems. Does anyone know if the new firmware had any effect on the problem?
    Mac Pro   Mac OS X (10.4.9)   4 GB Ram

    Our VPN is now working (checkpoint)
    For me the firmware update initially seemed to fix the VPN issue, but after closer inspection there still seems to be something wrong with it. (We are using CheckPoint.) My Wintel-box that has been provided by my employee is still having issues with connecting to our exchange server and the network drives do not seem to be working all that realiable. Probably a configuration issue, but do you have any ideas on where to start looking for a solution?
    br,
    -Joose

  • IMessage not working on 5S and iPad Air issues

    iMessage not working on 5S. Had 3 online chats with apple support but still not fixed. iPad air issues also; safari shuts down a lot on mine and my husbands iMessage not working. iMessage works on his 5S. Never had so many issues with Apple before. I receive SMS messages on 5S but no iMessage. It was suggested to me that I get a new sim or try another wifi, both seem odd given everything else works.
    My husband and I got our phones the same day, his works right, mine doesn't.
    iPad airs were purchased a month apart, mine works ok apart from safari shutdowns and his iMessage not working.
    Also the slider to answer calls on both phones not always working. Had to reboot one of them and it forced us to set it up again from scratch.
    Any ideas?

    restore from backup or restore as new.

  • IPad air issues

    I am having problems with my iPad air the wifi keeps disconnecting and is slow loading up I know the problem is with the iPad asit he wife has the ipad 2 which is out performing the iPad air.
    I have done all the resetting and restoring as stated on earlier posts I havesent it to apple and they are saying there is not a problem
    ANyone else having thes issues

    Some things to try first:
    1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
    2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
    3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at
    http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
    4. Go into your router security settings and change from WEP to WPA with AES.
    5.  Renew IP Address: (especially if you are drooping internet connection)
        •    Launch Settings app
        •    Tap on Wi-Fi
        •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
        •    In the window that opens, tap on the Renew Lease button
    6. Potential Quick Fixes When Your iPad Won’t Connect to Your Wifi Network
    http://ipadinsight.com/ipad-tips-tricks/potential-quick-fixes-when-your-ipad-won t-connect-to-your-wifi-network/
    ~~~~~~~~~~~~~~~~~~~~~~~~~
    Fix WiFi Issue for iOS 7
    http://ipadnerds.com/fix-wifi-issue-ios-7/
    iOS 6 Wifi Problems/Fixes
    Wi-Fi Fix for iOS 6
    https://discussions.apple.com/thread/4823738?tstart=240
    How To: Workaround iPad Wi-Fi Issues
    http://www.theipadfan.com/workaround-ipad-wifi-issues/
    Another Fix For iOS 6 WiFi Problems
    http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
    Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
    Fix For iOS 6 WiFi Problems?
    http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
    Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
    http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
    How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
    http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
    iOS 6 iPad 3 wi-fi "connection fix" for netgear router
    http://www.youtube.com/watch?v=XsWS4ha-dn0
    Apple's iOS 6 Wi-Fi problems
    http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
    ~~~~~~~~~~~~~~~~~~~~~~~
    iPad: Issues connecting to Wi-Fi networks
    http://support.apple.com/kb/ts3304
    How to Boost Your Wi-Fi Signal
    http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Boost-Your-Wi-Fi-Signal.hmL
    Troubleshooting a Weak Wi-Fi Signal
    http://ipad.about.com/od/iPad_Troubleshooting/a/Troubleshooting-A-Weak-Wi-Fi-Signal.htm
    How to Fix a Poor Wi-Fi Signal on Your iPad
    http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
    iOS Troubleshooting Wi-Fi networks and connections  http://support.apple.com/kb/TS1398
    iPad: Issues connecting to Wi-Fi networks  http://support.apple.com/kb/ts3304
    WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
    How to Fix: My iPad Won't Connect to WiFi
    http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
    iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
    iOS: Recommended settings for Wi-Fi routers and access points  http://support.apple.com/kb/HT4199
    How to Quickly Fix iPad 3 Wi-Fi Reception Problems
    http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
    iPad Wi-Fi Problems: Comprehensive List of Fixes
    http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
    Connect iPad to Wi-Fi (with troubleshooting info)
    http://thehowto.wikidot.com/wifi-connect-ipad
    10 Ways to Boost Your Wireless Signal
    http://www.pcmag.com/article2/0,2817,2372811,00.asp
    Fix iPad Wifi Connection and Signal Issues  http://www.youtube.com/watch?v=uwWtIG5jUxE
    Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
    How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
    Unable to Connect After iOS Update - saw this solution on another post.
    https://discussions.apple.com/thread/4010130
    Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
    Some Wi-Fi losses may stem from a problematic interaction between Wi-Fi and cellular data connections. Numerous users have found that turning off Cellular Data in Settings gets their Wi-Fi working again.
    You may have many apps open which can possibly cause the slowdown and possibly the loss of wifi. In iOS 4-6 double tap your Home button & at the bottom of the screen you will see the icons of all open apps. Close those you are not using by pressing on an icon until all icons wiggle - then tap the minus sign. For iOS 7 users, there’s an easy way to see which apps are open in order to close them. By double-tapping the home button on your iPhone or iPad, the new multitasking feature in iOS 7 shows full page previews of all your open apps. Simply scroll horizontally to see all your apps, and close the apps with a simple flick towards the top of the screen.
    Wi-Fi or Bluetooth settings grayed out or dim
    http://support.apple.com/kb/TS1559
    ~~~~~~~~~~~~~~~
    If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
     Cheers, Tom

  • IPad connectivety issues

    I have an iPad 2 using 6.1.3 and the Wifi connection within my house outside the room with router is really weak.
    I notice when I go to public WIfi locations, I have weak or no signal.
    This has been an issue since May 2012.
    In these same locations my Macbook Pro connects with no issues.
    What is the solution?

    Some things to try first:
    1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
    2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
    3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
    4. Go into your router security settings and change from WEP to WPA with AES.
    5.  Renew IP Address: (especially if you are droping internet connection)
        •    Launch Settings app
        •    Tap on Wi-Fi
        •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
        •    In the window that opens, tap on the Renew Lease button
    6. Potential Quick Fixes When Your iPad Won’t Connect to Your Wifi Network
    http://ipadinsight.com/ipad-tips-tricks/potential-quick-fixes-when-your-ipad-won t-connect-to-your-wifi-network/
    ~~~~~~~~~~~~~~~~~~~~~~~~~
    Wi-Fi Fix for iOS 6
    https://discussions.apple.com/thread/4823738?tstart=240
    iOS 6 Wifi Problems/Fixes
    How To: Workaround iPad Wi-Fi Issues
    http://www.theipadfan.com/workaround-ipad-wifi-issues/
    Another Fix For iOS 6 WiFi Problems
    http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
    Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
    Fix For iOS 6 WiFi Problems?
    http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
    Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
    http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
    How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
    http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
    iOS 6 iPad 3 wi-fi "connection fix" for netgear router
    http://www.youtube.com/watch?v=XsWS4ha-dn0
    Apple's iOS 6 Wi-Fi problems
    http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
    ~~~~~~~~~~~~~~~~~~~~~~~
    How to Boost Your Wi-Fi Signal
    http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Boost-Your-Wi-Fi-Signal.h tm
    Troubleshooting a Weak Wi-Fi Signal
    http://ipad.about.com/od/iPad_Troubleshooting/a/Troubleshooting-A-Weak-Wi-Fi-Sig nal.htm
    How to Fix a Poor Wi-Fi Signal on Your iPad
    http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
    iOS Troubleshooting Wi-Fi networks and connections  http://support.apple.com/kb/TS1398
    iPad: Issues connecting to Wi-Fi networks  http://support.apple.com/kb/ts3304
    WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
    How to Fix: My iPad Won't Connect to WiFi
    http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
    iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
    iOS: Recommended settings for Wi-Fi routers and access points  http://support.apple.com/kb/HT4199
    How to Quickly Fix iPad 3 Wi-Fi Reception Problems
    http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
    iPad Wi-Fi Problems: Comprehensive List of Fixes
    http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
    Connect iPad to Wi-Fi (with troubleshooting info)
    http://thehowto.wikidot.com/wifi-connect-ipad
    Fix iPad Wifi Connection and Signal Issues  http://www.youtube.com/watch?v=uwWtIG5jUxE
    Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
    How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
    Unable to Connect After iOS Update - saw this solution on another post.
    https://discussions.apple.com/thread/4010130
    Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
    Wi-Fi or Bluetooth settings grayed out or dim
    http://support.apple.com/kb/TS1559
    ~~~~~~~~~~~~~~~
    If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
     Cheers, Tom

  • Ipad Facebook issues, under "settings" Facebook will not accept my password, nor will it delete the account. Have tried deleting the FB app and installing it again, have tried restarting ipad, any thoughts?

    Ipad Facebook issues, under "settings" Facebook will not accept my password, nor will it delete the account. Have tried deleting the FB app and installing it again, have tried restarting ipad, any thoughts?

    same problem SO FRUSTRATING

  • AIR + iPad retina issue

    Will the air to iPad retina issue be fix in the flas pro cs6?

    Hi guys,
    1) I'm currently running a trial copy of CS6, Air 3.2, and I get 'App descriptor cannot parse file' error whenever I try to modify the xml file.
    I'm just trying to remove the icon shine, which worked fine in Flash 5.5.
    <key>UIPrerenderedIcon</key><true/>]]>
    Also, I tried inserting the 144x144 icon, which published ok, but didn't seem to work. And that line of code later disappeared from
    the xml.
    2) My mac is Snow Leopard, so I take it I have to upgrade to Lion (do I have to buy it, or is it free to developers?!)
    If I then get the latest XCode, and target ios 5.1 with Retina display, will my apps still be compatible on devices with iOS 4?
    Thanks,
    Matt

  • VPN issues following latest update

    Since the latest update in the o/s on February, my IPAD and IPHONE will not allow web pages to be opened once my VPN has connected. I have spoken many times to the VPN provider and they say it is Apple's o/s update that is the problem. The VPN works fine on my laptop. Why is it that no one seems ables to fix this very sensitive issue? As someone who uses their VPN daily, I miss the service very much.

    Same issue here. Vpn does not work on the ipad with ios updated but works fine on the older version ios.
    Been several weeks now. Would be good for apple to fix this!!!!!!!!!

  • ASA Iphone, Ipad VPN client pre-shared key (PSK) special characters bug

    I ran into this in a deployment of IPSec clients with apple ipad and iphone native vpn client. Here are details:
    Cisco ASA 8.2.5 OS
    Ipad, running 5.0.1
    Iphone i4S, running OS 5.0.1
    Special characters make your pre-shared key more secure, so i used a password generator app to make one that coincidently included a " (quotation mark). After configuring this PSK on a Ipad, i was unable to connect. I saw nothing in the ASA logs, indicating the Ipad didnt even try to connect.
    The Ipad generated the following error message:
    VPN Connection
    A configuration error occured
    OK Button
    After searching for quite some time, i found this somewhat obscure reference to the bug:
    http://blogs.oreilly.com/iphone/2008/07/strong-passwords-can-hurt.html
    Special thx to this guy!
    So i started to test special characters to see what would work, adding in 1 character at a time. Here is where I stopped:
    pre-shared-key !@#$%^&*()_-+=;:'<>,.
    These characters worked in the PSK. If you are curious, and want to play, have fun. I assume the alphnumerics will work since those are pretty standard.
    As a side note, here are a few more interesting items:
    1) The " (quote mark) does work when you run the real cisco vpn client. This was successful on a Windows 7 laptop with 5.X VPN Client.
    2) The ? (question mark) doesnt work as well, but that is a little easier to figure out because when you configure it on the ASA, context-sensitive help kicks in and knocks you off the config line.
    3) Iphone I4S suffers from the same issue - doesnt like quotes.
    4) Android is probably not affected by this bug, but I tested on an open source TUN driver- enabled adroid - not the bionic.
    Hope that saves someone some time, sometime!
    W

    Thanks for the tip.
    Help stamp out special characters in passwords. Their "strength" is a myth!
    Explained nicely here: http://xkcd.com/936/

  • Has anyone had this problem with VPN iPad vpn connection could not validate the server certificate

    Has anyone had this problem with IPad 3 after upgrade to IOS 7,
    trying to to connect VPN , but I get this messag, "could not validate the server certificate".
    I am trying to connect to Oracle VPN.

    Has anyone found a solution for this yet? I am still getting the could not validate server certificate error. I have tried importing the entire certificate chain as well as importing each individual cert in the chain. My certificate works perfectly with the cisco vpn on my pc.
    This is my first experience owning an apple product, and I am very disappointed with the customer support that I have received. I tried calling the help line and no one would even attempt to answer my question. I was then told that the Mac "geniuses" wouldn't know either and that I may be able to find an answer on the message boards. So I am reaching out to the community...Has anyone been able to figure out how to resolve this issue or even the specific cause? Any help is appreciated.

Maybe you are looking for

  • Calling a method on all replicas of a bean in one shot

              Hi,           Is there any properties by which one can make a replica aware stub direct a method call to all           instances of the bean in a cluster? The requirement is to update data cached in all instances           of a bean in the

  • Photostream no longer syncs to PC

    My photo stream no longer uploads photos to my PC, I've tried re-installing. It used to be fine until an update about a year ago.

  • Converting 2 tier to 3 tier?

    hello friends! I had a Java project which is developed using JSwing(Two Tier Architecture). I wish to convert it to Three tier Architecture. Can anyone suggest me how to do this effectively?

  • Emptying Trash is a problem...

    Recently I've not been able to see 'Empty Trash' in the Finder. What I can see is 'Secure Empty Trash". Both work and there are no issues, other than I have to key 'T' in Help to find 'Empty Trash". I'm sure that I'm missing the obvious but I'd appre

  • How do I attach an image to an iMessage in Mavericks?

    Hi, I receive images to iMessage on my iMac but I cannot work out how to attach an image. I can import an image from a camera or scanner and I can capture part of the screen, but I cannot work out how to attach an image I may have on my iMac or in my