IPad 3 and iPhone 5 will not stay connected to wifi although I am close to router and have strong signal

iPad 3 and iPhone 5 will not stay connected to wifi although I am close to router and have strong signal. I have to keep joining the network or restarting devices or forgetting network and rejoining it.  As a side note my 1st gen iPhone which I upgraded to iPhone 5 yesterday always stayed connected!

The steps to try would be to:
1. Restore the iPhone to Factory.
2. If that does not solve the problem replace the iPhone.
If Verizon is offering to replace the iPhone for free under warranty I would go with that option.

Similar Messages

  • My iphone 4s and my ipad both will not stay connected to wifi since the latest update ios.6

    my iphone will not stay connected to wifi since the ios 6.0 update

    Hello DickChris,
    The following article provides some useful troubleshooting steps and information that can help establish and stabilize Wi-Fi connections on your iPad.
    iOS: Troubleshooting Wi-Fi networks and connections
    http://support.apple.com/kb/TS1398
    Cheers,
    Allen

  • HT1695 My iphone 5 will not stay connected to wifi anywhere. I cant get it to connect at all. What can I do to get this fixed?

    My iphone 5 will not stay connected to wifi anywhere. I cant get it to connect at all. What can I do to get this fixed?

    does this only happen at your home network or with multiple networks?
    have you tried everything here? http://support.apple.com/kb/ts1398

  • Iphone will not stay connected "invalid response received from the device."

    I have an older iPhone (8gb) and for some reason whenever I plug it into the usb port on my computer it will not stay connected whatsoever. Itunes freaks out, it'll come up for a little bit and then just as soon as it appeared, 'Josh's iPhone' disappears. When I say "won't stay connected" I mean you'll hear the "new usb device" sound over and over again continuously and the iPhone goes crazy too. Like it's connected, disconnecting, connecting, disconnecting, etc.. The error I get during all this madness is "itunes could not connect iPhone because it received an invalid response from the device."
    I've used this ( http://support.apple.com/kb/ts1286 ) link to no avail (yet.) I am about to restart my computer right now. If it works after that I'll just simply delete this post. But anyway it's in a usb 2.0, it's plugged directly into the computer, etc etc
    Also I'm not sure if this has anything to do with it but I put ringtones on the phone as well, I tried adding about 5 or 6 of them through itunes and it only uploaded two of them, except one of those two appears FOUR TIMES.
    Thanks in advance for anyone who can help!

    Okay, after the updates I am still having the same problem. I'll try explaining it as detailed as possible, hoping somebody has an answer because this is pretty weird to me.
    -I have 5 files, Ringtone1.m4r, Ringtone2.m4r, Ringtone3.m4r, Ringtone4.m4r and Ringtone5.m4r.
    -I add them to the "ringtones" section under "Devices"
    -ON ITUNES they show up perfectly fine. In order, and if I play them through itunes, all the ringtones are correct, just how they should be.
    -I eject iPhone, go to settings > sounds > ringtone, and under custom, what I see is:
    Ringtone1
    Ringtone1
    Ringtone1
    Ringtone1
    Ringtone1
    Why on Earth could this be?

  • IMac and Mac Book Pro will not stay connected to WiFi on TC

    Hi,
    I'm a new Mac owner, and I changed completely over to Apple over the weekend.  Have na iMac and Mac Book Pro with a 2 TB Time Capsule.  Hooked everythng up and all seems to be working, except everytime my computers go into sleep mode when I wake them up they ask me to select my wireless network again because I lost connection.  Once I select my network it works fine until the computer goes to sleep.  WhenI wake it up, it asks me again.  I have it set to automatically connect to known networks, but it doesn't.  I have to click on it everytime I wake up the computer.  Before I hooked up the TC, I was using my old wireless router and it stayed connected.  Now that I put the TC in as my wireless neteork it asks me to select my network.  Is there something I'm not doing that may help the iMac and Mac Book Pro stay connected?
    Thanks. 

    For that particular WiFi update, yes - it means you can't download it. However, that update may have been included already in M-L 10.8 ...
    I feel your pain regarding these anomalies - I had the same problems on my year-old iMac that I just exchanged with Apple for a new one - I had worked these software/network issues on the old one for over five months, and finally, I demanded a new system as a replacement. Just too many problems. For me, Update 10.7.3 for Lion was the cause of my network problems. The WiFi update/patch solved the sleep issue for me, but not the auto-connect problem for system start-up's and restart's. After system start-up's and restart's, I would have to manually select my router address to connect via WiFi. But after manually selecting the address, the WiFi connection would stay-on - it wouldn't drop-off.
    Again, with this replacement iMac, I don't even trust its WiFi capability - and with a desktop, why should I ? I simply purchased a Cat-6 Ethernet cable, and wired it into my Time Capsule ... To heck with WiFi ! ... Remember: don't download ANY system updates wirelessly ! Don't do it. ... Apple will rue the day they did away with Ethernet connectors on their computers ... - The same goes for CD-based software, or at least some other "physical" means for software installation ...
    But, as for future system updates, and how they affect this new iMac ? - If they screw it up, I'm not messing with it ! - Apple's getting it back, the next day ! I'm not going to go through five months of testing, repairs, forced new purchases, etc. etc. ever again ...

  • HT4623 My iPhone 3G will not stay connected to wifi

    Can anyone tell me how to get my phone to stay connected to wifi?

    Settings > General > Reset > Reset Network Settings.
    Power cycle the router.

  • IPhone 4S not staying connected to wifi?

    I have both iPad and iPhone connected to same wifi, but my iPhone 4S does not stay connected.  I have tried to reset network, restart iPhone and they do connect but disconnects shortly afterwards.  Can anyone help me?

    Did you solve this problem? My new MacBook Pro 15" running 10.8.2 has exactly the problem you describe with our new Netgear N600. The other devices in our house (iMac running 10.5, a PC and an iPhone 3Gs) have no connectivity probelms at all.
    I have no problem connecting with my MBP at work or elsewhere. The problem is just at home with the N600.
    Tom

  • HT5569 New iPhone 6 not staying connected to wifi

    I have other phones and an iPad that have no issues. It seems after a few hours or maybe a day that the wifi connection will be lost and it will not come back. I have reset network settings and also restarted the phone. It works eventually but it shouldn't do this. Any thoughts?

    Some one mentioned that you can do a reset by pressing on the following: Settings > General > Reset > Reset Network Settings. 
    However I have done this and it made little difference in correcting this issue.  You can give it a try, but I believe Apple needs to correct this issue with an update, as the 8.1 did not make any improvement in this problem.

  • TS1398 Iphone 4s will not stay connected to wifi after update

    I can see my network, it connects for a few seconds and then disconnects. This started after the update.  I have tried reseting the router, the phone..............everything 100X.
    All my other devices work fine and other types of phones can connect to my network. It's a specific problem wth this phone.

    Hello Danielle,
    Thank you for the details of the issue you are experiencing with Wi-Fi on your iPhone 4s.  I recommend the following steps:
    Be sure you're in range of your Wi-Fi router (access point).
    Tap Settings > Wi-Fi and turn Wi-Fi off and on. If your W-Fi setting is dimmed, follow these steps.
    Confirm that your Wi-Fi router and cable or DSL modem are connected to power, turned on, and connected to the Internet. If not, refer to your network administrator or Internet service provider (ISP) for assistance.
    Restart your iOS device.
    Tap Settings > Wi-Fi and locate the Wi-Fi network to which you're connected.
    Tap and Forget this Network.
    Try to connect to your desired Wi-Fi network.
    Note: You may need to enter your Wi-Fi password again if your network requires one.
    Turn your Wi-Fi router off and on2. If your ISP also provides cable or phone service, check with them before attempting this step to avoid interruption of service.
    Update your device to the latest version of software.
    Update your Wi-Fi router to the latest firmware2. For AirPort Base Stations, install updates using the AirPort Utility.
    If the issue is still unresolved Wi-Fi disconnects or signal strength is less than expected
    Move closer to the Wi-Fi router (access point).
    Check for sources of potential interference.
    Remove any case, stand, or other accessories from your iOS device and see if signal strength improves.
    Reset network settings by tapping Settings > General > Reset > Reset Network Settings. Note: This will reset all network settings including
    previously connected Wi-Fi networks and passwords
    recently used Bluetooth accessories
    VPN and APN settings
    You can find the full article here:
    iOS: Troubleshooting Wi-Fi networks and connections
    http://support.apple.com/kb/ts1398
    Thank you for using Apple Support Communities.
    Best,
    Sheila M.

  • Ipad and iPhone will not send email by wifi

    Once I leave a wifi area the iPhone will send the email or I can connect the ipad to the iPhone and send it. I need to fix this before I go abroad.

    iOS: Understanding Personal Hotspot
    http://support.apple.com/kb/HT4517
    Use Bluetooth to tether your iPhone, iPod touch, or iPad
    http://www.macworld.com/article/1159258/bluetooth_tethering.html
    How to Connect an iPad to an iPhone Via Bluetooth Tethering
    http://techtips.salon.com/connect-ipad-iphone-via-bluetooth-tethering-25472.html
     Cheers, Tom

  • My IPad 2 with 5.0 will not stay connected to WIFI

    Since I upgraded to 5.0 on my Ipad 2 I cannot stay connected for more than a minute or two and then it loses the signal and I have to completely shut down and power up again. This only works for a minute or so and then it tells me there is no signal. I am in Lima Peru and newer routers are not likely to be here for a year or two, if old routers are a problem. I have tried the Ipad on several routers, different hotspots and the result is the same.

    Tried all of the above. My wife's Ipad works where mine does not.  Did restore to factory settings, twice, and still drops Wifi. IPad is under warranty and Apple said to send it in for warranty replacement. Problem is I am in Lima Peru so that is a little tougher to exchange.  The "store" that sells Apple here is only a shadow of a real Apple Store and are of little use or value except to buy new things in boxes at higher prices and limited inventories.
    Thanks for your suggestions however!

  • Airport express will not stay connected

    I have a new Airport Express (802.11n) and it will not stay connected to my MacBook Pro. Any suggestions?

    I have returned the Express and reinstalled my Extreme. I found a "tip" page that suggested to put a sheet of aluminum foil behind the Express to concetrate the signal inside the house. This crude idea has not solved the problem. My MacPro is a 2 GHz Intel Core i7. Any further suggestions?

  • Is anyone having a problem with the new iPad (Gen. 3) not staying connected to the charger? It seems to ALWAYS get jiggled loose and no longer be charging. My iPad 1 has no issue but I can't browse Internet w/o new iPad unplugging. Horrible!

    I notice that my new IPad (3rd generation) will not stay connected to the power cord at all, I'm not exagerating, if I plug it in and browse the Internet without fail it will become unplugged and I will have to push the plug back in (Ba-beep). Ive actually grown to despise that sound when you plug your iPhone or iPad in because it reminds me of how much money I spent on something that PHYSICALLY will not charge while I'm using it.
    I know the problem with it holding a charge while in use, I get it, the screen is amazing and it takes a lot to run the display, however, it is unacceptable to me that I can't even keep the thing plugged in while I'm using it. I can not even leave it on my Cal King bed overnight because I will wake up in the morning to find that the plug has been jiggled loose in a corner, so it's still attached but not making a connection thus not being charged. 
    I love the 4GLTE from Verizon and I love the iPad, but I'm actually using my 1st generation IPad while I am at home so I can leave my new $900 iPad on a table to charge free of incident so I can use the 4G while I'm away from wifi during the day. I have been getting more upset about this because I can not even use the Griffin extended cord to charge the iPad and be far from the plug because only the original apple sync/charge cord will have a better shot at staying in. Absolutely none of my non apple cables will stay in the iPad 3 while having it in my hands.
    The plug is at an angle, unlike the first iPad, not sure about the iPad 2. Please let me know if they have same issue.
    If anyone else is having this problem with the Gen 3 iPad please let me know because I'm tempted to do something about it with apple and I'm hoping that I just for some reason have a bad cable receiver or something and maybe I can get a replacement and enjoy the iPad as I had expected to. There is no reason why I should be even using my first iPad and I have friends that want to buy it but I am not selling it because I'm unable to sell it because I can't handle the new iPad while it's plugged in, that is ridiculous if it's a common issue so please let me know!

    Thanks for the swift reply, I have been looking online and a loose plug seems to be somewhat of an issue with many, I hope mine is actually a problem and not what others are experiencing. It's taken me this long to even reach out for the simple fact I HATE being a complainer but this is just horrible.
    Do you have an iPad 3 as well? And is yours not experiencing any issues close to mine?
    Thanks again!

  • IMovie for my iPad and iPhone will not export movies how do I fix this?

    iMovie for my iPad and iPhone will not export movies how do I fix this?

    Same here. Have exported a handful of movies before..faced this issue for the first time a few days ago. What footage are you trying to edit and export? (E.g. Shot with camera app, other social media apps like Snapchat, Vine, Instagram?)
    I did some troubleshooting..
    I was putting together all saved videos from Snapchat.. no luck. Export screen comes up, but progress bar doesn't move.
    Mixed some footage in there shot with actual iPhone camera app.. no luck.
    Removed all Snapchat footage.. it worked straight away.
    BUT ... it would make sense if I didn't just compile a bunch of Snapchat vids a few weeks ago and export them just fine?
    So it's something to do with the actual footage I assume?

  • HT204409 iphone 4s will not stay connected to verizon mi-fi 4510L device

    iphone 4s will not stay connected to verizon mi-fi 4510L device

    Reboot your router by removing all power from it for about 15 seconds.

Maybe you are looking for