IPad 3 charging issue with 10w power adapter

Hi everyone,
About the beginning of November, I purchased my first iPad. This is an iPad 3, wifi. Up until yesterday, I was able to charge my iPad using the 10w power adapter and cable from the box.
Since yesterday, that doesn't work anymore. I searched the internet but couldn't find a solution.
- I can charge my iPad 3 using my Macbook from late 2009, but it goes very slow. I don't get the screen and sound saying it's charging. I want to charge overnight and can't leave my computer on overnight.
- When I try to charge the iPad using the 10w power adapter and cable from the box, nothing happens. I don't get a lightning bolt or message saying it's charging. I don't get a message saying "not charging".
- I tried different outlets around the house, including outlets directly on the wall.
- I tried using my iPod classic from 2007 cable, no change. I hadn't expected it to work since the cable is fine, it's the power adapter that doesn't work.
- I tried rebooting, also a cold reboot. No changes.
- I can't take this to an Apple store since there is no Apple store near me.
- I'm not playing games on it.
- It doesn't charge when I plug it into the wall overnight.
This became a problem after using my iPad for about two weeks. Anyone who can help?

I ended up buying a 12w adapter. Because I'm not near an Apple store and the nearest one charges 30 euros an hour to even take a look, that's not really an option. That store also doesn't sell the ipad I have. Buying a new adapter was cheaper, and I can have it mailed home, and at least I'm sure it'll work and will go a bit faster.
Thanks for the help anyway!

Similar Messages

IPad WiFi 3G can't be charged using the 10W power adapter

Hi,
My new iPad gives me Not charging sign when I use the 10W power adapter comes with, and even I can't connect it to iTunes in my Macbook Air, windows XP, or windows7 laptops. I tried everything apple support provided but again nothing.
So, I'm open for suggestions.

I would try another charger and cable.
If that doesn't fix the problem, I'd take it back to the seller for replacement.

IPad won't charge using 10W Power Adapter

The subject states it all.
My iPad displays the words "Not Charging" besides the battery bar even when charged by the 10W power adapter that came along with the iPad.
Used the same power adapter to charge my iPhone and there was no problem.
Charged the same iPad using the same 10W power adapter a few times before and there were no issues either.
Any ideas?
Message was edited by: Wongjh

Hi,
Thank you for your suggestions.
I thought that my USB cable was faulty too at first. But after changing the USB cable and playing around with a few power adapters which did charge by iPhone, I guess the probability that the USB cables are faulty or that the problem lies with the power adapter seems rather low.
Changing power sockets didn't help.
By elimination, I suppose the only problem there can be should be with the iPad. My only concern is that it happened so sudden without me doing anything to the iPad (using it normally etc.)and how can I be sure it doesn't happen again in the future.
Pretty annoying.
*If I might add, plugging it in to the computer does not induce a response from iTunes (no detection).
Message was edited by: Wongjh

"iPad not charging Connect to a power adapter or a USB port on this mac to charge" Maverick issue!

Ever since we updated to mavericks our deployment of 60 iPad's flashes "iPad not charging Connect to a power adapter or a USB port on this mac to charge" on the screen every time one is plugged in. It is a false alarm because the iPad does in fact trickle charge and it does update the device like it is supposed to. At this point it's more of an annoyance then an actual problem. However I would like it to stop popping up every time one is plugged in.
Does anybody have any ideas to stop it?

Your computer USB port typically provides only 2.5W of power. iPads require 10-12W of charging power. That's why you get the "Not Charging" message. However, the iPad is charging, but much slower. There's no way to stop it.
 Cheers, Tom

IPod touch 5g using ipad 10w power adapter

Hi,
I want to ask if using ipad 10w power adapter to charging will effect iPod touch 5g battery cycle or make battery faulty ?

nononono! do not ,your ipod will starts to lag,just go to a store and get a normal 5v/1A charger.
check this : https://discussions.apple.com/thread/4536641?start=0&tstart=0 some1 was using that charger,his ipod starts to lag

HT1476 Hi! So my original iPhone 5 charger broke and I bought a 10 ft generic iPhone 5 charger And didn't come with a power adapter, what ***** is it charges slow. Can I use a different adapter? and will it effect my battery?

Hi! So my original iPhone 5 charger broke and I bought a 10 ft generic iPhone 5 charger And didn't come with a power adapter, what ***** is it charges slow. Can I use a different adapter? and will it effect my battery?

Nice try! Take a hike.

Charging with A1070 power adapter

Just bought a Nano 4th gen, tried to charge it with my A1070 Adapter. I know some older adapters won't work, but going through web support pages it seems this is one of the ones that should work.
Can someone advise please?
Thank you.

This is from another post, it might be helpful,
http://www.amazon.com/dp/B001HN6CVA/?tag=googhydr-20&hvadid=2655063891&ref=pdsl_15z29ty07eb
I have the same issue. My old ipod cable for wall outlets wont charge it but my old USB cable does, go figure. Other than that link im not sure there's anything else to do.

My ipod touch gets stuck on the same song, even after I uncheck the loop button. I am trying to play it in my 2007 vw with a power adapter that allows it to charge and play through my navigation unit. Please help. Thank you.

My ipod touch gets stuck on the same song, even after I uncheck the loop button. I am trying to play it in my 2007 vw with a power adapter that allows it to charge and play through my navigation unit. Please help. Thank you.

Yes, first try deleing both songs.
If still problem
Try:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Unsync all music and resync
- Reset all settings
Go to Settings > General > Reset and tap Reset All Settings.
All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.
If still problem, ,make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
Apple Retail Store - Genius Bar

Using my macbook pro whole day with the power adapter , will it affect my battery? Please help

Using my macbook pro whole day with the power adapter , will it affect my battery? Please help

It doesn't affect the battery. You can use your MacBook Pro plugged in all the time without damaging the battery. You only have to be sure that you unplug it and run a battery cycle (drain the battery without letting the Mac turn off and charge it fully) at least once a month to keep the battery life.
If you want more information about your battery > http://www.apple.com/batteries/notebooks.html

Z40-70 compatibility issue with your power management system

I noticed today that the Action Center says "Compatibility issue with your power management system." The description underneath is: Your power management system isn't working peoperly because a compatible driver is not available for this version of Windows. When I click on View message details it just says "Your computer was unable to download the solution at this time. Check to make sure your computer is connected to the Internet, and then try to download the solution again later." All power related functionalities however seem to be working. Battery is charging; battery percentage is showing; I can adjust screen brightness. I am not sure when exactly this problem started but it defenitely was not there before. Tried downloading and fixing the Power Management Software and updating BIOS. Still have the same message. System: Windows 8.1 64-bit

What model do you have? Can you post your MTM or model name?
Sometimes these messages are a false alarm.

Late 2008 MBP 15" not charging but runs off power adapter.

I've tried a known good adapter and have the same issues.
The power adapter light does not come on, but the machine indicates it is on AC but shows (not charging)
Sys Profiler information for power indicates:
Battery Information:
Model Information:
Serial Number:          6N8411AT13EB
Manufacturer:          SMP
Device Name:          bq20z951
Pack Lot Code:          0
PCB Lot Code:          0
Firmware Version:          002a
Hardware Revision:          000a
Cell Revision:          100
Charge Information:
Charge Remaining (mAh):          2773
Fully Charged:          No
Charging:          No
Full Charge Capacity (mAh):          4092
Health Information:
Cycle Count:          76
Condition:          Normal
Battery Installed:          Yes
Amperage (mA):          107
Voltage (mV):          11826
System Power Settings:
AC Power:
System Sleep Timer (Minutes):          120
Disk Sleep Timer (Minutes):          10
Display Sleep Timer (Minutes):          60
Automatic Restart on Power Loss:          Yes
Wake on AC Change:          No
Wake on Clamshell Open:          Yes
Wake on LAN:          Yes
Current Power Source:          Yes
Display Sleep Uses Dim:          Yes
GPUSwitch:          2
PrioritizeNetworkReachabilityOverSleep:          0
RestartAfterKernelPanic:          15
Battery Power:
System Sleep Timer (Minutes):          10
Disk Sleep Timer (Minutes):          10
Display Sleep Timer (Minutes):          2
Wake on AC Change:          No
Wake on Clamshell Open:          Yes
Display Sleep Uses Dim:          Yes
GPUSwitch:          2
Reduce Brightness:          Yes
RestartAfterKernelPanic:          157680000
Hardware Configuration:
UPS Installed:          No
AC Charger Information:
Connected:          Yes
ID:          0x0000
Wattage (W):          0
Revision:          0x0000
Family:          0x0000
Serial Number:          0x00000000
Charging:          No
I also have classic SMC symptoms (noisy fan, intermittant keyboard lights) and have tried SMC reset 2-3 times but am unsure if it has worked as power issue remains (another classic SMC symptom).
Any suggestions would be appreciated!

The battery conditions look decent, have you gone through the Troubleshooting MagSafe knowledge base article?
If nothing there helps, might be a good idea to make an appointment at an Apple genius bar and have the charger and computer checked out by the techs. See if something else is wrong, such as the charging circuitry that doesn't show on the system report.

Issue with Receiver SOAP adapter for synchronous scenario

Hello All,
We are facing a strange issue with the SOAP adapter in the interface we have setup. This is the 1st time we are using SOAP adapter in our system (PI 7.11 SP7). We are making a synchronous HTTP call to the web service exposed by another system in our landscape. The payload is send with SOAP envelope and there are no credentials to be maintained in PI settings.
The issue is that we are always getting timeout exception in PI audit logs after sending the request (3 minutes - standard timeout value, no additional config for this). But target system has confirmed that they are sending the response back. We tested from our server OS level and have received the response back in the same screen (to verify there is no firewall/port issue in between the systems). But when tried from RWB, it is always giving the timeout exception and we are not able to see any other log.
We have tried checking in the NWA logs as well after increasing the logging level to ALL for com.sap.aii.adapter.soap. But surprisingly, we didn't get any logs at all for the outgoing SOAP call or incoming response and hence we are unable to trace the issue.
We have setup another synchronous inbound SOAP interface (PI exposing the webservice) and it is working fine. We are also able to trace the logs in both audit log and NWA logs.
Is there anywhere else we can check for the logs? Audit logs is showing timeout error and we are not able to see anything in NWA logs.
Does the target system need to maintain PI credentials in the header when they send the synchronous response back?
Are there any specific settings which should be checked to enable the sync communication? (this should not be the case since the inbound interface is working fine)
Please help.
Thanks
Justin

Hi Amit,
Thanks for the reply.
Yes we had tested successfully via SOAP UI as well (forgot to mention that). We are getting back the expected response in SOAP UI without using any credentials. We got the same response when we tested it through OS commands from PI server.
The WS is hosted by the target system and they haven't maintained any credentials at their end. So when PI is trying to access, we don't need to provide any credentials. My question is, whether the target system should keep any credentials to send the synchronous response back to PI (java stack). We have tried that as well but since there aren't any logs, we are unable to verify whether the credentials are coming correctly.
The service interfaces are correct and PI configuration are OK. I will try the XPI inspector for logs as you have suggested.
Thanks
Justin

IMac went totally black. No power to the unit. Have there been issues with the power supply?

My iMac went totally went black tonight when my grandchildren were using the iMac. I can't power it up? Have there been issues with the power supply?

It may just be the power cord (between the mains and the computer). If you have an Apple store or Authorised store near you, take the cord in and check it out. Indeed, check if it has been partly pulled out by pressing it firmly into the back of the computer.

Issue with JMS inbound Adapter and Asynchronous BPEL

Hi Gurus,
I am facing the below issue with JMS inbound Adapter and Asynchronous BPEL .
I have 2 JMS Queues one inbound and one outbound . The Composite has multiple BPEL Components around 4 on an average and i have 4 composites similar to that .
Totally 4 Composites * 4 BPEL Components = 16 Services
Propoesd Solution :
I have used MessageSelector in the JMS Adapter for selecting the incoming message. The BPEL gets invoked if the message selector is true and proceses the Message and writes the response to the other Queue.
Initially i had no problems but intermittantly the BPEL processes are getting invoked but they are not processing the data ( Bpel process is supposed to invoke an external service and get the response in a sync call) and each BPEL processe instance is in running state for ever . This remains even if i restart the servers .
The message gets read by the JMS Adapter , BPEL instace gets created but it wont proceed futher and remains in the runnign state for ever.
If i redeploy the Composite then messages get processed but the issue creeps up again ( i tried to checl the logs but ino cluea about the issue .
Getting frustrated day by day tried the bpel.config.transaction, increased the JMS Adapter threads , inreased the worker threads but all in vein..
please let me know if any one has faced similar issue .
Anticipating a quick response from the gurus.
Lakshmi.

We are also facing this issue in 11.1.1.5.
Breifly the issue is : The BPEL process which polls an inbound JMSAdater ( consume_message) either stays in running state forever ( whatever we do) or go to the recovery queue. It doesnt recover even if i try to recover it. This happens intermittently. Redeploying the application / restarting servers sometime solve the issue but as know we cant do that on prod systems .
Can some one look into this on priority and help us giving a solution/workaround.

Hi I'm from the UK and I'm visiting the US in June I was wondering would I be able to buy a Mac mini over in the US and use it in the UK with a power adapter. Thanks!

Hi I'm from the UK and I'm visiting the US in June I was wondering would I be able to buy a Mac mini over in the US and use it in the UK with a power adapter. Thanks!

You won't need a plug adapter if you buy a figure-of-eight mains lead (like most portable radios etc) with a UK plugtop to replace the original lead.

IPad 3 charging issue with 10w power adapter

Similar Messages

Maybe you are looking for