IPad charging in car and connection to CD changer unit at the same time

Hi all,
Firstly, this is my first post here, so apologies if my post is either considered rude or unto wards in any fashion. Apologies also if this question has been covered elsewhere - I have searched the forums to sone extent, but cannot guarantee that I haven't missed something!
I'm looking for a splitter cable for in-car use with the iPad.
The specifics of my car stereo are as such :
no bluetooth
No AUX either.
I have a CD Changer connect at the rear of the car head unit, to which is attached a factory installed cable. This cable is CD Changer plug for the car stereo end, going to 30-pin connector at the other end.
This is a perfect solution for my old iPod photo - it allows me to control the iPod via the car stereo, AND charge the iPod at the same time.
However...
I have an iPad 2 which I would like to use in place of the iPod photo. I wish to plug the iPod (Music app) into the car stereo, and use one of the GPS apps, AND charge the iPad 2 all at the same time.
There is not enough juice coming from the car stereo to allow me to do all this concurrently, as you will probably be aware. If my car journeys were short, I would not be too worried, but I often use the car for journeys that are longer than 10 hours. The iPad, with the GPS and iPod apps running at the same time, will not remain "alive" for this amount of time - the longest I've managed is about 6 and a half hours before the iPad runs out of juice.
So I'm looking for a splitter that I can slot into the dock connection of the iPad and will split into USB for the cigar lighter and into a 30 pin (female) that will go to the 30 pin (male) connector that runs to the CD Changer port on the car stereo.
In other words (and I hope this diagram works) :
                                                              IPad
                                                         USB.     30-pin (f)
                                                        /.                 30-pin (m)
                                            Cigar lighter.                CD Changer plug
I have looked everywhere on line, have contacted various cable suppliers (such as USBFever) but up 'till now I have had no joy.
Anyone have any ideas?
Thanks in advance.                               

Thanks, Rudegar, for your reply.
Unfortunately, I wouldn't know where to start, not being terribly technically minded. And I'm not sure that this would be an economic resolution - would this involve buying soldering irons etc.? And would I be able to be sure that I wouldn't mess something up, and cause overheating/other damage to the iPad itself?
Surely this must be a fairly common problem, however? I'm sure that I'm not the only one looking for such thing??
Anyone else have a solution?
Thanks.

Similar Messages

  • Is it possible to connect the iPad to an Infocus and a remote for ppt presentations at the same time?

    I've always used PC and I'm planning on making the transition to Mac.  That's why I'm considering buying an iPad. Today I went to Best Buys and the Mac guy told me that it isn't possible to connect the iPad to an Infocus and a remote for ppt presentations at the same time. Is that true?  I'm a speaker and that was the main reason I was considering buying an iPad, so I didn't have to carry my laptop. Thanks for your help!

    Thanks for your reply. Looks like it can as I have just found this https://www.youtube.com/watch?v=nKp02y4JXVs

  • I have an Iphone 6 plus. Can the bluetooth connect to the cars speaker system and a Garmin HUD unit at the same time?

    I have an Iphone 6 plus. Can the bluetooth connect to the cars speaker system and a Garmin HUD unit at the same time?

    Hi,
    Normally yes, Bluetooth can connect to multiple devices at the same time, so yes.
    The only thing is that you'll be able to send sound/music to only one at a time, but I understand the Garmin HUD doesn't play sounds.
    cheers

  • Outlook Anywhere Loosing connection : Outlook Event id 26 and Exchange IIS HTTPERR Log : Connection_Dropped_List_Full at the same time

    Hi,
    I have a Windows 2008R2 Updated / Exchange 2010 SP3 Rollup 7 (Role CAS,HUB,MBX) with only external users connection : ActiveSync, EWS, OWA, Outlook Anywhere.
    4 processors and 24Go of memory are allocated to the Exchange server VM (VMWare).
    Netscaller is used as reverse proxy in DMZ.
    There is around 500 users connecting with Outlook Anywhere to Exchange. Users are using Outlook 2010 or 2013 with last updates and cache mode enabled (owner mailbox and delegations). Users are location all around the world (around 50 sites). So no users
    is domain integrated.
    Users are complaining about disconnection, and Outlook freeze (Outlook is not responding). This happened at any point of time during the day, and for different kind of actions (Outlook is just open, Try to press Send button, try to press Transfer button).
    The freeze happened randomly for users. I have seen the problem, and Outlook sometimes freeze during few seconds, sometimes during 5 minutes without any reason. (no file copy, no action asked...)
    I noticed that freeze are matching with the Outlook event id 26  on the workstation (Connection to the Microsoft Exchange Server has been lost. Outlook will restore the connection when possible). Also, at the same time, I can see around 200 lines in
    the IIS HTTPERR Log (Exchange Server : C:\Windows\System32\LogFiles\HTTPERR) the following lines:
    2014-11-20 10:39:43 NETSCALLERIP PORT EXCHANGEIP 443 HTTP/1.1 RPC_OUT_DATA /rpc/rpcproxy.dll?EXCHANGEFQDN:6004 - 1 Connection_Dropped_List_Full MSExchangeOutlookAnyWhere
    2014-11-20 10:39:43 NETSCALLERIP PORT EXCHANGEIP 443 HTTP/1.1 RPC_OUT_DATA /rpc/rpcproxy.dll?EXCHANGEFQDN:6001 - 1 Connection_Dropped_List_Full MSExchangeOutlookAnyWhere
    What has been already checked :
    Check IOPS: seems to be normal
    Check Processor consumption: seems to be normal
    Netscaller TimeOut = 8h
    Bandwidth where the server is hosted : more than enough
    Bandwidth of client internet connection : Traffic do not increase when the problem happen
    Firewall TimeOut : seems to be ok
    Firewall Protocol Filter : seem to be ok
    Workstation MTU : Ok : ping -l -f 1472 = Ok, so best MTU = 1500 (1472+28)
    Outlook Profile : Clean Up OST, sync of all folders, download address book.
    wireshark on workstation : nothing seems to be wrong but difficult to analyse, so I maybe missed something.
    Configuration change on Exchange :
    HKLM\Software\Policies\Microsoft\Windows NT\RPC\MinimumConnectionTimeout = 120
    Disable throttling Policy
    Adsiedit, change Max Memory alloc for ESE : msExchESEParamCacheSizeMax = 327680 (around 10GB) msExchESEParamCacheSizeMin = 131072 (around 4GB
    Adsiedit, change Min Memory alloc for ESE : msExchESEParamCacheSizeMin = 131072 (around 4GB)
    Host file : add hostname and FQDN of Exchange Server
    Disable IPV6 : HKLM\System\CurrentControlSet\services\TCPIP6\Parameters\DisabledComponents = HEX 0xffffffff
    IIS : system.applicationHost : webLimits : minBytesPerSecond = 0
    Create dedicated IIS AppPool MSExchangeOutlookAnyWhere for /RPC and /RPCWithCert
    AppPool MSExchangeOutlookAnyWhere : Regular Time Interval (minutes) : 0
    AppPool MSExchangeOutlookAnyWhere : Queue Length : 20000 (Should be the solution but not working)
    netsh int tcp set global chimney=disabled
    netsh int tcp set global rss=disabled
    HKLM\SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\MaxUserPort = 65534
    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\KeepAliveTime : 300000
    HKLM\SYSTEM\CurrentControlSet\Services\Netlogon\Parameters\MaxConcurrentAPI = 150
    IIS machine.config : <system.web> : requestQueueLimit="65535"
    Microsoft.Exchange.RpcClientAccess.Service.exe.config <add key=”LoggingTag” value=”ConnectDisconnect, Logon, Failures, ApplicationData, Warnings, Throttling”/>
    Uninstall All agents (except Backup Agent)
    Uninstall Antivirus
    Will be done tonight :
    Exchange and DCs : HKLM\SYSTEM\CurrentControlSet\Services\Netlogon\Parameters\MaxConcurrentAPI = 100
    Exchange IIS : Increase AppPool MSExchangeOutlookAnyWhere Queue Length to 40000
    Exchange : decrease HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\KeepAliveTime to 60000
    You're welcome if you have any idea.
    Thanks.
    Jo.

    Hi,
    Thanks for your answer. Here are my comments :
    1. Disable IPv6 then restart your Exchange server
    Already done since the install of Exchange.
    2. Confirm if there is any NLB device in your environment, please remove NLB firm client server
    There is only one Exchange server in the Org. So no NLB installed on the server (NLB is used on the Netscaller used as a reverse proxy). In Addition, the article apply for Windows 2008, or the server is installed with Windows 2008 R2.
    3. If there is a proxy server configured in IE, please uncheck it
    I guess you are talking on the client side. There is no proxy on the client side, Outlook Anywhere connect directly to the internet.
    4. Collect more error logs in Event Viewer in Exchange and collect the IIS logs in
    folder “c:\inetpub\logs\logfiles\W3SVC1”
    the error I reported in the description is from IIS, and always appear when end users report a problem. In W3SVC1 file, there is also errors, but those one appear even if Outlook clients are working fine. So I cannot isolate any specific
    error. The most common from W3SVC1 log are :
    2014-11-25 08:02:17 EXCHANGEIP POST /autodiscover/autodiscover.xml - 443 - NETSCALLERIP Microsoft+Office/15.0+(Windows+NT+6.1;+Microsoft+Outlook+15.0.4667;+Pro)
    401 1 2148074254 0
    2014-11-25 08:02:17 EXCHANGEIP POST /EWS/Exchange.asmx - 443 - NETSCALLERIP Mac_OS_X/10.9.5+(13F34)+CalendarAgent/176.2
    401 1 2148074254 0
    2014-11-25 08:02:18 EXCHANGEIP POST /EWS/Exchange.asmx - 443 - NETSCALLERIP Microsoft+Office/14.0+(Windows+NT+6.1;+Microsoft+Outlook+14.0.7128;+Pro)
    401 1 2148074254 0
    Regards,
    Jo.

  • How do I design my posters on Photoshop touch for ipad, to be A0 and export them to creative cloud at the same size???

    How do I design my posters on Photoshop touch for ipad, to be A0 and export them to creative cloud at the same size???
    every time I do it it comes out at a fraction of the size and not even an A size...
    Please help

    A0 is pretty big if you go at a high DPI for printing. It's about 10000 x 14000 pixels at 300 DPI.
    PS Touch can handle about 12 Megapixel image imports (which is about 4000 x 3000 pixels). PS Touch, interestingly, can create 4096 x 4096 pixel projects from scratch.
    Adding to that, PS Touch always exports at 72 DPI. Take note that this is probably due to tablet hardware. Tablet hardware is "getting there" but it still has a ways to go before it matches its desktop cousin.

  • If i have my mac mini and my mac air connected to my thunderbolt display at the same time how do I switch between each of them without unplugging one of them?

    If i have my mac mini and my mac air connected to my thunderbolt display at the same time how do I switch between each of them without unplugging one of them? (By the way im mirroring my macbook air to my thunderbolt display not dual screening it)

    That's not what home sharing is for or how it works.
    You want the remote app.

  • This morning Find My Phone alert went off on all my devices connected to my Apple ID at the same time, is this a bug or should I be worried that my id is hacked? I didn't have Find My Phone app installed on many of these devices. Please advice. Thanks

    This morning Find My Phone alert went off on all my devices connected to my Apple ID at the same time, is this a bug or should I be worried that my id is hacked? I didn't have Find My Phone app installed on many of these devices. Please advice. Thanks in advance.

    If you have enabled Find My iPhone/iPad on your devices, any one with access to your Apple ID and Password can Play Sound on your devices.
    Tap to enlarge image.

  • Remote and direct update of master data at the same time

    Hello
    Is it possible to do remote and direct update of master data at the same time? If yes where it could be used?
    Thanks

    Hi,
    What do you mean by Remote Update ?
    regards
    Happy Tony

  • How to open and save pictures from 1 folder at the same time?

    Is there a way to open and save pictures from 1 folder at the same time?
    I'm creating a vi that resizes the picture but I want to do it with 1 folder at a time... Is this possible?
    greetings!

    Hi Kway,
    Here you are. I wrote a file a customer times ago & It did what you want!
    Just see the attachements and keep me inform.
    Regards,
    Julien Roland - District Sales Manager
    NI Belgium - Technical Support
    Don't forget to rate a good answer
    Attachments:
    Test existing Files.vi ‏23 KB
    Delete files from array of files (SubVI).vi ‏16 KB

  • Error : Old and new exceptions cannot be used at the same time.

    HI ALL,
    i build a new exception class with message class and i want to replace the
    old exception that i had in the method ,what i did is delete the exception from the method
    signature and add the exception class .
    the problem is that when i try to activate the method i get error :
    Old and new exceptions cannot be used at the same time.
    CALL FUNCTION 'CALCULATE_HASH_FOR_CHAR'
          EXPORTING
            alg            = 'MD5'
            data           = iv_iss
          IMPORTING
            hash           = lv_issu
          EXCEPTIONS
            unknown_alg    = 1
            param_error    = 2
            internal_error = 3
            OTHERS         = 4.
        IF sy-subrc <> 0.
          RAISE EXCEPTION TYPE cx_user_mng EXPORTING
          textid = cx_user_mng=>wrong_isrs.
        ENDIF.
    I want to use the new exception class ,
    how can i avoid this error ?
    Best Regards
    Edited by: Joy Stpr on Jul 22, 2009 2:56 PM
    Edited by: Joy Stpr on Jul 22, 2009 3:16 PM

    Hi Joy,
    Check this link.
    [Old and New Exceptions Cannot be used at same time|Urgent problem, give me a hand;
    Old and new exceptions cannot be used the same time, what does this mean???
    Regards,
    Lakshman.

  • How can I record an Audio Instrument (saxophone) and listen to a reference track at the same time?

    How can I record an Audio Instrument, and listen to a reference track at the same time?

    Are you using an external audio controller or the line-in and headphone jacks on the side of your computer? You shouldn't have an issue using headphones when you're recording through the line-in but you may want to make sure you have monitoring on and it's going to the right place.
    If you're using an external audio controller, try making an aggregate device combining the controller and the "built-in output" into the same device. Go to Applications/Utilities/Audio MIDI Setup, click the "+" sign at the bottom left to make a new device and check the "use" boxes to the left of the physical devices you want to use as part of that aggregate device. That is how I use the computer's speakers or headphones to monitor my input as opposed to only being able to use the output on my audio controller.
    Now that I see some of the questions on the side of this page I realize that the 13" MBPs seem to have only one combined input/output jack... That is an incredibly stupid feature. What on Earth could possibly justify that design decision? I suppose if that's the problem you're having you'll have to buy some sort of splitter (if they even make them) or get an external audio controller like an Apogee Duet or something along those lines. I would be furious if they combined those two jacks on all of the MBPs.

  • In windows how do we install and activite multiple versions of tuxedo at the same time ?

    Hi All,
    In windows how do we install and activate multiple versions of tuxedo at the same time ?
    Advance wishes

    You can run different versions of Tuxedo on the same server, as long as they are installed in different directories.
    See PeopleTools 8.53 installation manual Task 3-1: Installing Oracle Tuxedo
    You can install Oracle Tuxedo once for each release on a machine, regardless of the number of PeopleSoft
    applications or databases the server supports. For example, if you are a PeopleSoft 9.1 customer and have
    Oracle Tuxedo 6.5 installed, you may install Oracle Tuxedo 6.5 and Oracle Tuxedo 11gR1 on the same
    machine in separate directories. For example:
    On Windows, you may install into C:\oracle\tuxedo11gR1_VS2010 and C:\tux65.
    On UNIX, you may install into /home/oracle/tuxedo11gR1 and /prod/tuxedo/6.5.
    E-TUX: Can Multiple Versions of Tuxedo Coexist on One Physical UNIX or Linux Server? (Doc ID 607828.1)

  • HT1442 install and run mac os 10.4 at the same time mountain lion 10.8

    nstall and run mac os 10.4 at the same time mountain lion 10.8

    I was able to install Intel Tiger into VMWare Fusion 2.0; I was never successful at installing it in VMWare Fusion 4.
    If you have had success in version 4, please let us know how to do it!  Thanks!

  • I recently bought a 4th generation ipod shuffle.  Am I able to have both music and audio podcasts loaded on it at the same time?

    I have not been able to include both music and audio podcasts on my shuffle at the same time. Is this possible with the shuffle?

    I disabled all my computer's firewalls and sure enough, IT WORKED!! My iPod is updated and just now finishing restoring! Thank you SOOOO SOOO much. : D

  • When im facetiming with someone and im watching a youtube video at the same time, the volume for the youtube video is lowered and the facetime volume stays the same, how can i change that?

    When im facetiming with someone and im watching a youtube video at the same time, the volume for the youtube video is lowered and the facetime volume stays the same, how can i change that?

    Have you ever even used skype on an iphone or ipod?  We tried it and there is no way to type to each other while you are video chatting.  You can do the typing during the video on a COMPUTER, but not on an iphone or ipod.

Maybe you are looking for

  • Remote access VPN issues using Pix 501

    We have taken over a network where there was little to no documentation. I have a remote access VPN terminated on a Pix 501 that is having a connectivity issue. I can connect using Cisco VPN Client. There is a server on the inside network that is use

  • I am trying to restore my locked ipad however, I get an error message in itunes, what do I do next?

    I am tryint to restore my locked ipad 2, however, in itunes I get 2 popup messages.  The first pop up says "itunes can not connect to ipad because it is locked and requires a password"  So I attempted to restore the ipad and an error message "itunes

  • Can't "Print" to disk with Adobe PDF 8.0 Printer

    If I want to create a PDF, I select "Print" from the File menu. In the Print Dialog box I select "Adobe PDF 8.0" as the printer. Then click on the "Print" button and the "Save As" dialog appears. Select "Desktop" and click "Save" button. It acts like

  • Iweb pages all jumbled

    After a period of NOT updating website........open to find text on one website all jumbled up.  Website appears OK online........but not sure what to do and/or how to change. Have a couple other websites that appear OK Any ideas?

  • Using a JMS control from an EJB project

    I'm developing an EJB in Workshop and my EJB is expected to send messages to a JMS queue. How can I use a JMS control (JCX) from my EJB?