IPad disconnected during update. Now all I have is the Apple logo

My iPad was disconnected during todays iOS update. Now it's frozen on the Apple logo screen. Any help out there?

Hi, PikFlyer.  
Thank you for visiting Apple Support Communities.  
I understand that your iPad is unresponsive at the Apple logo when attempting to update.  I would recommend going through the troubleshooting steps below. 
If you see a black screen
You might need to charge your device before it can turn on. Plug in your device and let it charge for at least 10 minutes (20 minutes for iPad), then try turning it on. 
You should see a battery icon while your device is charging. If you continue to see a black screen, reset your device. If your device doesn't respond when you press buttons
Your device might not return to the Home screen when you press the Home button, wake from sleep when you press the Sleep/Wake button, slide to unlock or power off, or it might appear frozen. Try these steps:
Restart your device.
If it still doesn't respond, or if it doesn't turn back on, reset your device.
If your device gets stuck during startup
When starting up, you might see the Apple logo or a red or blue screen for a long time, or your device might restart again. Try these steps:
Make sure that you have iTunes 12 or later on your computer.
Put your device in recovery mode.
When you get the option to restore or update, select Update. This will reinstall iOS without erasing your data.
Get more help
If you still need help after trying the steps above, contact Apple Support. 
If your iPhone, iPad, or iPod touch doesn't respond or doesn't turn on
Cheers, 
Jason H.  

Similar Messages

  • My ipad shut-off and now all i get is the apple logo and a spinning circle. Any suggestions on why and what I can do about it?

    my ipad 2 shut off and now all I get is the apple logo and a spinning circle

    Try holding down the home button and the sleep / wake button at the same time to restart the iPad .

  • I recently restarted my iphone and now all that appears is the apple logo how do i fix this problem

    i recently restarted my iphone and now all that appears is the apple logo how do i fix this problem?????

    Plug it into your computer and restore it.

  • Tried Resetting, Now all I see is the APPLE logo and loading

    Ok so here it is....I bought a used original iphone of a friend of mine. On my way home, I decided to reset the iphone to its original settings....now its been like 6 hours....and all I see is the apple logo, then it tries to load and it stays that way....then it blinks and the apple logo comes on again. Is there anything I can do??

    You should put the phone into DFU mode and restore it in iTunes.
    To put your phone in DFU mode:
    1. connect the phone to a computer with iTunes
    2. Hold the home button and sleep/wake button simultaneously for 8 seconds.
    3. Let go of the sleep/wake button and continue holding the home button
    4. If successful a dialog box will appear in iTunes that states that an iPod was detected in recovery mode. The phone's display will remain black.
    5. Click ok in the dialog box, then click restore
    After that the phone should be functional.
    I hope this helps.

  • While updating my ipod it crashed and now all I get is the apple logo on the screen.

    I clicked on the update operating system that had a notification next to it. It downloaded for a long while then asked me to hook up to itunes. I didi and it said it was downloading again . Then updating. Then said update failed and now all that shows on the screen is the apple logo. Also
    the ipod won't shut off. Please help.

    This device is not eligible for the requested build (Also sometimes displayed as an "error 3194")
    Update to the latest version of iTunes.
    Third-party security software or router security settings can also cause this issue. To resolve this, followTroubleshooting security software issues.
    Downgrading to a previous version of iOS is not supported. If you have installed software to performunauthorized modifications to your iOS device, that software may have redirected connections to the update server (gs.apple.com) within the Hosts file. Uninstall the unauthorized modification software from the computer.
    Edit out the "gs.apple.com" redirect from your hosts file, and then restart the computer for the host file changes to take affect. For steps to edit the Hosts file and allow iTunes to communicate with the update server, see iTunes: Troubleshooting iTunes Store on your computer, iPhone, iPad, or iPod—follow steps under the heading Blocked by configuration (Mac OS X / Windows) > Rebuild network information > The hosts file may also be blocking the iTunes Store. If you do not uninstall the unauthorized modification software prior to editing the hosts file, that software may automatically modify the hosts file again on restart.
    Avoid using an older or modified .ipsw file. Try moving the current .ipsw file (see Advanced Steps > Rename, move, or delete the iOS software file (.ipsw) below for file locations), or try restoring in a new user to ensure that iTunes downloads a new .ipsw.
    Also:
    iPhone Error 3194 - How to Fix iTunes Error 3194?
    Fix Error 3194 from iTunes during iPhone restore

  • HT4623 i failed to update properly update my itouch, now all i see is the apple logo. how to fix it?

    the update to iOS 6.1.5 has been on my itouch for a couple of months so i decided to just go with it without any knowledge on how to properly do it. All i did was delete my apps and thats only because theres nothing special with them. Then i pressed dowload and when i ot past that i installed. i thought i was doing the right thing but now all i see is the blinking apple logo. what shoud i do?

    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try on another computer                            
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
      Apple Retail Store - Genius Bar                                              

  • HT4623 I deleted all contents from my iphone 3gs so that i could give it to my nephew....now all i get is the apple logo and nothing will come on. have i deleted the programme completely if so how can i get it back???

    I think theoperating system from my iphone 3GS has gone

    Restore the device with iTunes > http://support.apple.com/kb/HT1414
    You may need to put it into Recovery Mode first > http://support.apple.com/kb/HT1808

  • HELP! my phone froze and all i have is the apple logo

    can someone help me i plugged it in to my comp. and they told me to hold top buttom for 3 secs. but then what??

    Connect iPhone to Wall Charger and Reset, hold both Home and Power buttons until the iPhone begins to restart. This may take about 20 seconds time of holding both buttons.
    If you decide you need to restore the firmware. Then open iTunes on computer, then connect iPhone to computer, then hold both Home and Power buttons until iTunes recognizes iPhone in Recovery Mode. Usually again takes about 20 seconds time of holding both buttons. Restore the Firmware.

  • I cannot open ipad 2 after i update to ios 7..only the apple logo keeps on displaying..please help..

    I cannot open my ipad 2 after update to ios 7..only the apple logo keeps on displaying..please help..

    Power-cycling or connecting to iTunes didn't fix the issue.  However the iPad did restart, trying to install the update but it didn't complete and received a error once again.  And now the iPad is stuck on the update screen with the progression bar beneath the apple.
    The error reads, "The iPad could not be updated.  An unknown error occurred (6)."

  • HT201210 i updated my iphone and now all i have on the screen is the itunes icon

    i updated my iphone and now all i have on the screen is the itunes icon

    1)  Connect to iTunes on the computer you usually Sync with and Restore
    http://support.apple.com/kb/HT1414
    2)  If necessary Place the Device into Recovery mode...
    http://support.apple.com/kb/HT1808
    Note on Recovery Mode.
    You may need to try this More than Once...
    Be sure to Follow ALL the Steps...
    Once you have Recovered your Device...
    Re-Sync your Content or Restore from the most Recent Backup...
    Restore from Backup  >  http://support.apple.com/kb/ht1766
    NOTE:
    Make sure you have the Latest Version of iTunes (v11) Installed on your computer
    iTunes free download from www.itunes.com/download

  • I tried updating my ipod touch to iOS6 then an unknown error occured so i disconnected it an now it is stuck on the apple sign and has a loading sign and has been like this for 2 hours. what can i do?

    I tried updating my ipod touch to iOS6 then an unknown error occured so i disconnected it an now it is stuck on the apple sign and has a loading sign and has been like this for 2 hours. what can i do?
    My home button is also unresponsive and i have to press it really hard to make it work.

    Do you remember the the exact wording of the error message:
    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iPod fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - If still not successful that indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.

  • I have an iphone 3gs. It was jail broken. I reset it back to factory settings and now all I have on the screen is the apple logo.I have hooked the phone up to itunes but nothing is happening.What do i do.Can someone help???/

    I have an iphone 3gs. It was jail broken. I reset it back to factory settings and now all i have on the screen is the apple logo.I have hooked  the phone upto itunes but nothing is happening. What do i do? Can someone help please???

    Sorry, due to the Terms of Use problems with jailbroken devices can't be discussed here.
    You can only get help from those people who told you to modify the software, only they know what the jailbreak did to the firmware.

  • I have been given a iphone3gs today and after restoring it to factory settings like i was adviced to, my phone now wont boot up past the apple logo, it will switch to black screen if i press both buttons. I havnt managed to sync it to itunes. how do i get

    I have been given a iphone3gs today and after restoring it to factory settings like i was adviced to, my phone now wont boot up past the apple logo, it will switch to black screen if i press both buttons. I havnt managed to sync it to itunes. how do i get it to work???

    Try to connect in recovery mode, explained in this article: iOS: Unable to update or restore

  • I have a 2 ibook g4's this is the second one but I started it up and all that happens is the apple logo comes up on a white screen and then nothing happens what should I do?

    I have a 2 ibook g4's this is the second one but I started it up and all that happens is the apple logo comes up on a white screen and then nothing happens what should I do?

    Reinstall OS X.

  • TS4062 All I have is an Apple Logo on my Screen....

    All I have is an Apple Logo on my Screen.I bought the Phone on Ebay and wiped it.Itunes doesnt recognize it?

    Perhaps the phone was jailbroken when you got it.

Maybe you are looking for

  • ITunes match wont let me play my songs

    I have iTunes match, so i am able to listen to all my music, where ever i am, on any device, without it taking up disk space. That´s all fine and dandy...BUT every time i launch iTunes on my work computer (macbook pro retina, with mavericks, logged i

  • Color .jpg/.gif images in the .CHM and true (4BPP/8BPP) grayscale in Printed Output?

    I do all my document creation in RH first, then output WinHelp and to Word 2003. I want to keep color images in the CHM and have a majority of the images become true monochrome grayscale in the Word doc. Yes, Word does have a nifty "grayscale" optopn

  • Setting up CF9 in Distributed Environment

    I need to install CF9 in a distributed environment, with the CFM pages on Server A, and the CF9 runtime stuff on Server B. I have searched around all over the place and can't find a good set of instructions for this. In the past (with MX) we have jus

  • Wrapping pl/sql

    Hello I am running XE DB 11g R2 on a windows 7 64 bit machine. I am trying to wrap some package bodies. c:\oracle_home\bin> wrap iname=c:\sourcecodedirectory\mysql.sql oname=c:\wrappedcodedirectory\mysql.wrp Sometime the wrap produces a wrapped file

  • NIO Echo Server SocketChannel.write() multiple times?

    Hello, I have found and experimented with two simple nio echo socket servers, one from hutchinson's book. The other has similar code:      if (key.isWritable())      SocketChannel client = (SocketChannel) key.channel();      ByteBuffer output = (Byte