Ipad is disabled connect ti itunes, ipad is disabled connect ti itunes

ipad is disabled connect ti itunes, ipad is disabled connect ti itunes

If the iPad is disabled because you've forgotten the passcode then you will need to connect the iPad to the computer that you normally sync to and you should then be able to reset the iPad and re-sync your content to it (http://support.apple.com/kb/HT1212) - you may need to put the iPad into recovery mode : http://support.apple.com/kb/ht1808
If you do it via a different computer then :
If you restore on a different computer that was never synced with the device, you will be able to unlock the device for use and remove the passcode, but your data will not be present

Similar Messages

  • HT1212 My ipad is disabled and says it needs to be connected to itunes, when i connect it to itunes, itunes says that i need to put my passcode in my ipad for it to recognize it, but since it is disabled, i cant do this, how can i resolve this problem?

    My ipad is disabled and it says i need to connect to itunes when i connect it to itunes, it says it wont recognize it until i put my passcode into my ipad, but with my ipad disabled, this is immposible, how can i resolve this problem?

    You may need to put the iPad into recovery mode : http://support.apple.com/kb/ht1808 - you should then be able to reset the iPad an resync your content to it

  • Hey, my ipad is disabled and i cant open. i tried connecting it with itunes in recovery mode to restore it but it wont work it doesnt show and options itunes doesnt detect my ipad in recovery mode. what do i do know? please help!!!

    Hey, my ipad is disabled and i cant open. i tried connecting it with itunes in recovery mode to restore it but it wont work it doesnt show and options itunes doesnt detect my ipad in recovery mode. what do i do know? please help!!!

    If you followed these instructions and you were unable to enter recovery mode, I'm still leaning toward a hardware problem.  Also, since you have IOS-7, read this.  It might help.

  • My ipad is disabled and it says I must connect to itunes.  When I connect to itunes it says I need to enter a passcode on my ipad but I can't type anything on my ipad.

    My ipad is disabled and says I need to connect to itunes.  When I connect to itunes it says I need to enter a passcode on my ipad however there is no place to enter as passcode.  The screen is locked.

    You need to restore using Recovery Mode. You can read about it here.
    http://support.apple.com/kb/ht4097

  • HT1212 Ipad is disabled and I get a message to connect to Itunes. When I do that, Itunes tells me to enter passcode on my Ipad but I cant because it's disabled:(

    My Ipad is disabled and tells me to connect to Itunes. When I do that, I get the message to enter passcode on my IPad but I can't because it's disabled:(
    In one of the options, it tells me to sync as if I have never synced to itunes but I'm afraid it will reset to factory settings and I will lose what I had on Ipad.

    Locked Out, Forgot Lock or Restrictions Passcode, or Need to Restore Your Device: Several Alternative Solutions
    1. iOS- Forgotten passcode or device disabled after entering wrong passcode
    2. iPhone, iPad, iPod touch: Wrong passcode results in red disabled screen
    3. Restoring iPod touch after forgotten passcode
    4. What to Do If You've Forgotten Your iPhone's Passcode
    5. iOS- Understanding passcodes
    6. iTunes 10 for Mac- Update and restore software on iPod, iPhone, or iPad
    Forgotten Restrictions Passcode Help
    You will need to restore your device as New to remove a Restrictions passcode. Go through the normal process to restore your device, but when you see the options to restore as New or from a backup, be sure to choose New.
    Also, see iTunes- Restoring iOS software.

  • Ipad is disabled connect to itunes but i connected it and there was a popup saying itunes cannot connect to ipad because it is locked with a passcode. You mus enter the passcode on the ipad before it can be used with itunes. but i couldnt enter my passwor

    my ipad is disabled and it said ipad is disabled connect to itunes but i connected it and was restoreing it and then there was a popup and it said itunes cannot connect to ipad because it is locked with a passcode. and you must enter the passcode on the ipad before it can be used with itunes. But i couldnt even write the passcode on my ipad cause it was disabled. What should i do now????

    Follow the instructions on this page to reset your iPad : http://support.apple.com/kb/HT1212
    Note: If iTunes asks you to enter the passcode, try another computer that you have synced with. Otherwise, go to "If you have never synced your device with iTunes, or you do not have access to a computer" section below.
    If you have never synced your device with iTunes, or you do not have access to a computer
    If you see one of following alerts, you need to erase the device:
    "iTunes could not connect to the [device] because it is locked with a passcode. You must enter your passcode on the [device] before it can be used with iTunes."
    "You haven't chosen to have [device] trust this computer"
    If you have Find My iPhone enabled, you can use Remote Wipe to erase the contents of your device. If you have been using iCloud to back up, you may be able to restore the most recent backup to reset the passcode after the device has been erased.
    Alternatively, place the device in recovery mode and restore it to erase the device:
    Disconnect the USB cable from the device, but leave the other end of the cable connected to your computer's USB port.
    Turn off the device: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for the device to shut down.
    While pressing and holding the Home button, reconnect the USB cable to the device. The device should turn on.
    Continue holding the Home button until you see the Connect to iTunes screen.
    iTunes will alert you that it has detected a device in recovery mode. Click OK, and then restore the device.

  • My iPad conveys that it is disable, and that I need to connect to iTunes.  When I connect to iTunes I get a message that I need to enter my pass code and open my Ipad, but I don't get the number board to open with a password.  How do I fix this?

    My iPad conveys that it is disabled, and that I need to connect to iTunes.  When I connect to iTunes I get a message that I need to enter my pass code and open my Ipad, but I don't get the scree with the number board to open with a password.  How do I fix this?

    You will need to restore it. The sidebar of your iPad appears on itunes even if you dont enter the passcode. There's the option to restore it. More info:
    iTunes: Backing up, updating, and restoring your iPhone, iPad, or iPod touch software

  • My iPad conveys that it is disabled, and that I need to connect to iTunes.  When I connect to iTunes I get a message that I need to enter my pass code and open my Ipad, but I don't get the screen to open with a password.  How do I fix this?

    My iPad conveys that it is disabled, and that I need to connect to iTunes.  When I connect to iTunes I get a message that I need to enter my pass code and open my Ipad, but I don't get the screen to open with a password.  How do I fix this?

    You will need to restore it. It may not sync, but the iPad's sidebar has to appear you can restore it and it will be as the last time ou synced it to iTunes. For more info:
    iTunes: Backing up, updating, and restoring your iPhone, iPad, or iPod touch software

  • TS2446 my daughter had disabled her ipad by putting in passcode to many times, says connect to itunes but then it wont work as says passcode needs to be put in

    my daughter had disabled her ipad by putting in passcode to many times, says connect to itunes but then it wont work and says passcode needs to be put in

    Follow the instructions in this article http://support.apple.com/kb/ht1212 and you should be able to fix the ipad but keep in mind there is a it is very likely that you will lose all information on the ipad following the instructions in the article

  • HT201412 my apple ipad is disabled and saying connect to itunes. i tried to connect with itunes but not responding

    my apple ipad is disabled and saying connect to itunes. i tried to connect with itunes but not responding

    Connect to iTunes on the computer you usually Sync with and “ Restore “...
    http://support.apple.com/kb/HT1414
    If necessary Place the Device into Recovery mode...
    http://support.apple.com/kb/ht4097

  • HT1212 itunes could not be connected to ipad because it is locked with a passcode, i must enter a passcode on the ipad before it can be used with itunes but all i see is "iPad is disabled connect to itunes" I have a passcode but nothing shows on the scree

    itunes could not be connected to ipad because it is locked with a passcode, i must enter a passcode on the ipad before it can be used with itunes but all i see is "iPad is disabled connect to itunes" I have a passcode but nothing shows on the screen

    iOS: Device disabled after entering wrong passcode
    http://support.apple.com/kb/ht1212
    How can I unlock my iPad if I forgot the passcode?
    http://tinyurl.com/7ndy8tb
    How to Reset a Forgotten Password for an iOS Device
    http://www.wikihow.com/Reset-a-Forgotten-Password-for-an-iOS-Device
    Using iPhone/iPad Recovery Mode
    http://ipod.about.com/od/iphonetroubleshooting/a/Iphone-Recovery-Mode.htm
    Saw this solution on another post about an iPad in a school enviroment. Might work on your iPad so you won't lose everything.
    ~~~~~~~~~~~~~
    ‘iPad is disabled’ fix without resetting using iTunes
    Today I met my match with an iPad that had a passcode entered too many times, resulting in it displaying the message ‘iPad is disabled – Connect to iTunes’. This was a student iPad and since they use Notability for most of their work there was a chance that her files were not all backed up to the cloud. I really wanted to just re-activate the iPad instead of totally resetting it back to our default image.
    I reached out to my PLN on Twitter and had some help from a few people through retweets and a couple of clarification tweets. I love that so many are willing to help out so quickly. Through this I also learned that I look like Lt. Riker from Star Trek (thanks @FillineMachine).
    Through some trial and error (and a little sheer luck), I was able to reactivate the iPad without loosing any data. Note, this will only work on the computer it last synced with. Here’s how:
    1. Configurator is useless in reactivating a locked iPad. You will only be able to completely reformat the iPad using Configurator. If that’s ok with you, go for it – otherwise don’t waste your time trying to figure it out.
    2. Open iTunes with the iPad disconnected.
    3. Connect the iPad to the computer and wait for it to show up in the devices section in iTunes.
    4. Click on the iPad name when it appears and you will be given the option to restore a backup or setup as a new iPad (since it is locked).
    5. Click ‘Setup as new iPad’ and then click restore.
    6. The iPad will start backing up before it does the full restore and sync. CANCEL THE BACKUP IMMEDIATELY. You do this by clicking the small x in the status window in iTunes.
    7. When the backup cancels, it immediately starts syncing – cancel this as well using the same small x in the iTunes status window.
    8. The first stage in the restore process unlocks the iPad, you are basically just cancelling out the restore process as soon as it reactivates the iPad.
    If done correctly, you will experience no data loss and the result will be a reactivated iPad. I have now tried this with about 5 iPads that were locked identically by students and each time it worked like a charm.
    ~~~~~~~~~~~~~
    Try it and good luck. You have nothing more to lose if it doesn't work for you.
     Cheers, Tom

  • TS3274 my ipad displays "ipad disabled,connect to i tunes",but if connected to itunes it doesnt recognizes it because of the wrong passcodes entered several times.and when i go to restoring, i could not find the summary in the device panel in my i tunes.h

    my ipad displays" ipad disabled, connect to i tunes" but if connecyed to i tunes, it doesnt recognizes it bec.of the wrong passcodes entered several times.so when i go to restoring ipad, i couldnt see the 'summary' in the device panel in my i tunes.what will i do? pls help...

    You have to restore the device within iTunes. You want to use the same computer that you always sync with so that you can restore your app data and settings. You can restore with any other computer, but you will lose everything on the iPad.
    Try using Recovery Mode
    iPad: Unable to update or restore

  • My kids entered the passcode several times wrong and now it is disabled and written on it"connect to itunes" , when i did connect it to itunes it said "can not connect to ipad because it is locked with a passcode" what can i do pls?

    my kids entered the passcode several times wrong and now it is disabled and written on it"connect to itunes" , when i did connect it to itunes it said "can not connect to ipad because it is locked with a passcode" what can i do pls?

    You may need to put the iPad into recovery mode : http://support.apple.com/kb/ht1808 - you should then be able to reset the iPad and restore/resync your content to it.
    If you do it via a different computer that it's not normally synced to then (from here) :
    If you restore on a different computer that was never synced with the device, you will be able to unlock the device for use and remove the passcode, but your data will not be present.

  • I have entered the wong password on mi iPad 2 too many times and it says disabled connect to iTunes so when i plug it into the computer , iTunes says pad locked cannot sync until you unlock the iPad but i don't remember the password nor can i put it in

    i have entered the wong password on mi iPad 2 too many times and it says disabled connect to iTunes so when i plug it into the computer , iTunes says pad locked cannot sync until you unlock the iPad but i don't remember the password nor can i put it in

    You have to restore the device within iTunes. You want to use the same computer that you always sync with so that you can restore your app data and settings. You can restore with any other computer, but you will lose everything on the iPad.
    iOS: Wrong passcode results in red disabled screen
    This will tell you how to restore
    iTunes: Backing up, updating or restoring iOS software
    If you cannot restore that way, you may have to use recovery mode
    iPad: Unable to update or restore

  • My iPad is disabled, connect to iTune, but when i connect to iTune, iTune showing to allow access please respond on iPad

    My iPad is disabled, connect to iTune, but when i connect to iTune, iTune showing to allow access please respond on iPad. but in long time it is not showing on device list of iTunes.
    can any one help me.

    How can I unlock my iPad if I forgot the passcode?
    http://www.everymac.com/systems/apple/ipad/ipad-troubleshooting-repair-faq/ipad- how-to-unlock-open-forgot-code-passcode-password-login.html
    iOS: Device disabled after entering wrong passcode
    http://support.apple.com/kb/ht1212
    How can I unlock my iPad if I forgot the passcode?
    http://tinyurl.com/7ndy8tb
    How to Reset a Forgotten Password for an iOS Device
    http://www.wikihow.com/Reset-a-Forgotten-Password-for-an-iOS-Device
    Using iPhone/iPad Recovery Mode
    http://ipod.about.com/od/iphonetroubleshooting/a/Iphone-Recovery-Mode.htm
    You may have to do this several times.
    Saw this solution on another post about an iPad in a school environment. Might work on your iPad so you won't lose everything.
    ~~~~~~~~~~~~~
    ‘iPad is disabled’ fix without resetting using iTunes
    Today I met my match with an iPad that had a passcode entered too many times, resulting in it displaying the message ‘iPad is disabled – Connect to iTunes’. This was a student iPad and since they use Notability for most of their work there was a chance that her files were not all backed up to the cloud. I really wanted to just re-activate the iPad instead of totally resetting it back to our default image.
    I reached out to my PLN on Twitter and had some help from a few people through retweets and a couple of clarification tweets. I love that so many are willing to help out so quickly. Through this I also learned that I look like Lt. Riker from Star Trek (thanks @FillineMachine).
    Through some trial and error (and a little sheer luck), I was able to reactivate the iPad without loosing any data. Note, this will only work on the computer it last synced with. Here’s how:
    1. Configurator is useless in reactivating a locked iPad. You will only be able to completely reformat the iPad using Configurator. If that’s ok with you, go for it – otherwise don’t waste your time trying to figure it out.
    2. Open iTunes with the iPad disconnected.
    3. Connect the iPad to the computer and wait for it to show up in the devices section in iTunes.
    4. Click on the iPad name when it appears and you will be given the option to restore a backup or setup as a new iPad (since it is locked).
    5. Click ‘Setup as new iPad’ and then click restore.
    6. The iPad will start backing up before it does the full restore and sync. CANCEL THE BACKUP IMMEDIATELY. You do this by clicking the small x in the status window in iTunes.
    7. When the backup cancels, it immediately starts syncing – cancel this as well using the same small x in the iTunes status window.
    8. The first stage in the restore process unlocks the iPad, you are basically just canceling out the restore process as soon as it reactivates the iPad.
    If done correctly, you will experience no data loss and the result will be a reactivated iPad. I have now tried this with about 5 iPads that were locked identically by students and each time it worked like a charm.
    ~~~~~~~~~~~~~
    Try it and good luck. You have nothing more to lose if it doesn't work for you.
    ~~~~~~~~~~~~~
    iPad not appearing in iTunes
    http://www.apple.com/support/ipad/assistant/itunes/
    iOS: Device not recognized in iTunes for Mac OS X
    http://support.apple.com/kb/TS1591
    iOS: Device not recognized in iTunes for Windows
    http://support.apple.com/kb/TS1538
    iTunes for Windows: iTunes can’t contact the iPhone, iPad, or iPod software update server
    http://support.apple.com/kb/ts1814
    windows 8.1 itunes wont recognize ipad
    https://discussions.apple.com/thread/5697247?start=0&tstart=0
    Look at the solution in this link
    https://discussions.apple.com/thread/5697247?start=75&tstart=0
    iTunes for Windows: Device Sync Tests
    http://support.apple.com/kb/HT4235
    IOS: Syncing with iTunes
    http://support.apple.com/kb/HT1386
    Apple - Support - iPad - Syncing
    http://www.apple.com/support/ipad/syncing/
    iTunes 10.5 and later: Troubleshooting iTunes Wi-Fi Syncing
    http://support.apple.com/kb/ts4062
    iOS: “Not enough free space” alert when trying to sync
    http://support.apple.com/kb/ts1503
    You may need to delete iTunes on your computer and then reinstall.
    How To Completely Uninstall and Remove All Traces of iTunes
    http://zardozz.com/zz/2008/04/how-to-completely-uninstall-and-remove-all-traces- of-itunes.html/
    Wi-Fi Sync Not Working? Here’s How to Fix it for All iOS Devices
    http://osxdaily.com/2013/02/17/wi-fi-sync-not-working-fix-ios/
     Cheers, Tom

Maybe you are looking for

  • Is there more simple interface library than OCI for C.

    I read OCI 8.0 documentation and I think that API like CLI XOpen standard but this standard is much complicated. So I am looking for a way to interacting with server in manner such as PostgreSQL interface library or MYSQL interface library or Sybase

  • What are the steps in RMAN Backup & Recovery 10 G

    Hi All Please list out What are the steps in RMAN Backup & Recovery 10 G Regards

  • Problem in line formate..

    Hi all, This is a little bit urjent. In the GLPCA-SGTXT(Table) iam having some text like 'This is good ##'.i was downloded some other data with this text('This is good ##') by using report program in to aplicationserver(AL11) and from there iam uploa

  • Inverse object-group concept

    Does Cisco have a way to write an ACL to block the opposite of an object-group? For example, I want to write an ACL allowing all traffic other than to object-group Corp_Net... thanks, ttpm

  • Wrong Forum I know but I don't see any forums for complaints

    Hi, Is there a forum out there where you can post complaints? In my case it is an insolence when replies are deleted because I wrote some critique to the last poster ( about boastful and unnecessary answers ). Is this the policy of oracle? Freedom of