Ipad not found when connected to laptop

Ipad not found when I connected to laptop and itunes

iOS: Device not recognized in iTunes for OS X
iOS: Device not recognized in iTunes for Windows

Similar Messages

Ipad wont charge when connected to laptop but charges when connected to wall outlet

ipad wont charge when connected to laptop but charges when connected to wall outlet

The quickest way (and really the only way) to charge your iPad is with the included 10W or 12W (5W on Mini) USB Power Adapter. iPad will also charge, although more slowly, when attached to a computer with a high-power USB port (many recent Mac computers) or with an iPhone Power Adapter (5W). When attached to a computer via a standard USB port (2.5W, most PCs or older Mac computers) iPad will charge very slowly (but iPad indicates not charging). Make sure your computer is on while charging iPad via USB. If iPad is connected to a computer that’s turned off or is in sleep or standby mode, the iPad battery will continue to drain.
Apple recommends that once a month you let the iPad fully discharge & then recharge to 100%.
How to Calibrate Your Mac, iPhone, or iPad Battery
http://www.macblend.com/how-to-calibrate-your-mac-iphone-or-ipad-battery/
At this link http://www.tomshardware.com/reviews/galaxy-tab-android-tablet,3014-11.html , tests show that the iPad 2 battery (25 watt-hours) will charge to 90% in 3 hours 1 minute. It will charge to 100% in 4 hours 2 minutes. The new iPad has a larger capacity battery (42 watt-hours), so using the 10W charger will obviously take longer. If you are using your iPad while charging, it will take even longer. It's best to turn your new iPad OFF and charge over night. Also look at The iPad's charging challenge explained http://www.macworld.com/article/1150356/ipadcharging.html
Also, if you have a 3rd generation iPad, look at
Apple: iPad Battery Nothing to Get Charged Up About
http://allthingsd.com/20120327/apple-ipad-battery-nothing-to-get-charged-up-abou t/
Apple Explains New iPad's Continued Charging Beyond 100% Battery Level
http://www.macrumors.com/2012/03/27/apple-explains-new-ipads-continued-charging- beyond-100-battery-level/
New iPad Takes Much Longer to Charge Than iPad 2
http://www.iphonehacks.com/2012/03/new-ipad-takes-much-longer-to-charge-than-ipa d-2.html
Apple Batteries - iPad http://www.apple.com/batteries/ipad.html
Extend iPad Battery Life (Look at pjl123 comment)
https://discussions.apple.com/thread/3921324?tstart=30
New iPad Slow to Recharge, Barely Charges During Use
http://www.pcworld.com/article/252326/new_ipad_slow_to_recharge_barely_charges_d uring_use.html
Best Practices for iPad Battery Charging
http://www.ilounge.com/index.php/articles/comments/best-practices-for-ipad-batte ry-charging/
Tips About Charging for New iPad 3
http://goodscool-electronics.blogspot.com/2012/04/tips-about-charging-for-new-ip ad-3.html
How to Save and Prolong the battery life of your new ipad
https://discussions.apple.com/thread/4480944?tstart=0
Prolong battery lifespan for iPad / iPad 2 / iPad 3: charging tips
http://thehowto.wikidot.com/prolong-battery-lifespan-for-ipad
iPhone, iPod, Using the iPad Charger
http://support.apple.com/kb/HT4327
Install and use Battery Doctor HD
http://itunes.apple.com/tw/app/battery-doctor-hd/id459702901?mt=8
To Extend a Device’s Battery Life, Get to Know It Better
http://tinyurl.com/b67c7xz
iPad Battery Replacement
http://www.apple.com/batteries/replacements.html
In rare instances when using the Camera Connection Kit, you may notice that iPad does not charge after using the Camera Connection Kit. Disconnecting and reconnecting the iPad from the charger will resolve this issue.
 Cheers, Tom

My ipad wont charged when connected to laptop. HELP?!!!

my ipad wont charged when connected to my laptop. Anyone know how to fix that. thanks, much appreciated
Also, just noticed this now....i have it connected and its got no battery. It will shut off like it died (while connected to the laptop) and then after a few minuted it will turn on. with the battery icon saying "not charging"

Chances are your USB port is charging but only when the screen is off. This is e behaviour i get from our pcs.
Make a note of the battery level, plug it in and make sure the screen is off, after and hour check the battery level.
It should have charged a bit but very, VERY slowly.
Your computer port normally only delivers 500mha of power. Some modern macs deliver 1100mha. Anything less than 1000mha wont charge with the screen in.
The iPhone charge delivers 1000mha and the iPad charger delivers 2100mha.
So it not charging via the computer is normal.

Page not found when connecting to server (if not logged in on server)

Hi,
When we try to connect to the presentation server (http://esddev02:9704/analytics/saw.dll?Dashboard) we get a page not found error if I don't open a remote desktop connection session on the server first.
I suppose the problem originates in the fact that the installation of the software has been done with my credentials on the server.
The windows services start with 'Local System' as logon but the OC4J seems to start only when I log on with my user.
I don't see a reason for this as in the registry the OC4J start command is found under HKEY_LOCAL_MACHINE.
Changing this to "D:\OracleBI\oc4j_bi\bin\oc4j.cmd -start& " did not change anything.
Has somebody got a clue?
Tx for any advice,
Kris

Hi,
I checked further on this today. Problem is not solved yet. I need to find a way to start the OC4J server independent from my session on the server.
Has anybody got some advice?
Brgrds,
Kris

JDBC Driver not found when connecting to Data Federator XI 3.0 SP3

Hello,
I am trying to connect Crystal 2008 to Data Federator however I am getting the Error
Failed to open connection.
Details: JDBC Driver not found.
The JDBC Drivers are installed and working for the Universe Designer, however I am unable to get it working for Crystal. I am using the following connection parameters on Crystal:
Connection URL: jdbc:datafederator://<<servername>>:3055/<<catalog>>
Database Classname: com.businessobjects.datafederator.jdbc.DataFederatorDriver
Any Advice on what I may have missed?

The issue was solved, thanks to Patric Wan:
u201CFailed to open the connection. Details: JDBC driver not found.u201D
This means Data Federator JDBC driver was not added to:
C:\Program Files\Business Objects\common\<version>\java\CRConfig.xml
How to connect the Data Federator Server using JDBC?
1. Retrieve the following files from the machine where Data Federator is installed, from the directory [data-federator-installation-dir]/JdbcDriver/lib.
    - thindriver.jar
    - avalon-framework-4.1.5.jar
    - jacorb.jar
    - log4j-1.2.8.jar
    - logkit-1.2.jar
2. Copy these files to a directory of your choice ([your-jdbc-driverdirectory]).
3. Add [your-jdbc-driver-directory]/thindriver.jar to CRConfig.xml   <Add to Classpath tag, you can refer to original sample.CRConfig.xml should be at: C:\Program Files\Business Objects\Common\4.0\java\CRConfig.xml, or search your BOBJ products install to find this file>
4. URL: jdbc:leselect://<host>[:<port>][/[<catalog>]][[;param-name=value]*]
Class Name : LeSelect.ThinDriver.ThinDriver
Edited by: Craig Sander on Feb 12, 2011 8:22 PM

Camera not found when connect Canon Rebel T3

When i attempt to contact my Cannon Rebel T3 to my computer it states no camera found, cannont be used with this version of the operating system. Not a computer or camera guru and have no idea what to do. I have checked for updated software but my computer states it is up to date. Any help would be appreciated!!

I just went to the canon website and saw that just a few days ago they released the software. Go to
http://www.usa.canon.com/cusa/consumer/products/cameras/slr_cameras/eos_rebel_t3 _18_55mm_is_ii_kit#DriversAndSoftware

New movies are not found when connecting to my camera

Hi,
I Use a Sony HDR XR550VE. After soem time of happy use of iMovie, it now no longer discovers new clips at import.
Hooking it up to iMovie and importing new clips has working fine in the beginning untill the point at which I deleted the camera's harddrive content (using the camera's commands), and started making a really long movie (over 6 hrs). THat did not import very well: half of it wasn't discovered via the iMovie import dialogue. Since then, new movies I've shot are not discovered anymore and can't be imported. Accessing the drive directly via the "Import films" option allows me to drill all the way down to the AVCHD-mts source file, but are displayed grayed out and can't be selected to be imported.
Please help.
Thanks,
Jeronias

Hi Jeronias,
Sorry to hear that things have gone a bit pear-shaped for you again.
You may have already tried this, but deleting iMovie's preference file sometimes helps when iMovie is not working as it should. The file can become corrupted in some circumstances, such as when iMovie quits unexpectedly or is "Force Quit".
Close iMovie then, in Finder, navigate to the file named "com.apple.iMovieApp.plist" in your User (Home)>Library>Preferences folder. Drag the .plist file to the Trash. When next opened iMovie will create a fresh file with the default settings, which you can change if desired in iMovie's menu item iMovie>Preferences.
Hopefully, that may get things back to normal.
I'm interested in the procedure you are using (or attempting to use) to import your video into iMovie. I have a similar camcorder, the Sony HDR-SR7, which records AVCHD video to a 60 Gb hard drive. Your model, of course, has a 240 GB hard drive and also records to Memory Stick and SD/SDHC cards.
When I connect my camera via USB and turn it on, a dialogue appears on the LCD touch screen. I then have to touch the hard drive icon in order for the camera to be recognized by my MacBook Pro. With iMovie open, it takes a couple of minutes (maybe less) before the import screen appears. Is this the way you normally go about importing your footage? Of course, you will have 2 import sources - the hard drive and/or a memory card.
Have you tried importing from a memory card using a card reader, rather than connecting the camera? If this works, then the import problem is isolated to the camera itself. I'm assuming that iMovie is not recognizing the hard drive nor the card when the camera is connected via USB.
So, in summary:
What process are you using to import from the camera?
Have you tried using a card reader?
Have you tried deleting the preference file?
John

I just get the new iPad air and when connecting it to my laptop, why the battery is not charging?

just get the new iPad air and when connecting it to my laptop, why the battery is not charging?

A lot of computers don't provide enough power to their USB ports to charge the iPad at a sufficient rate - it may still be charging slowly, and should be a bit quicker if the iPad's screen is off (if you leave it for a while and then disconnect it from your computer you may find that it's battery percentage has gone up). The wall charger is usually the most efficient way to charge the iPad.

Tv not supported when connecting HDMI to ipad 30 pin connector running ios 8

tv not supported when connecting HDMI to ipad-2 30 pin connector running ios 8. Was working fine with ios 7.

Hello,
I need to conect it to either a mouse or an OLED display to transfer the content I was going to use thee standard charging USB to a port splitter and sending it from there but I wanted to check before I did something stupid.
Thanks.
James

Why does FCP error "File Not Found" when I try to open my sequences????

I recently updated all of my software and the following day I started getting errors "file not found" when I would try to open a sequence. Now all of my sequences are being lost and I am losing time and money because I can't meet deadlines! This *****!!! With one sequence I had to reedit the entire thing from scratch and when I did for some reason the old one would then open. But the next time I opened FCP both sequences would error out. Following the "file not found" the computer responds with another error "error: out of memory" What the devil is going on with this crap?

I seem to have figured out what my problem was. After trying to build the same project (that failed on the Mac Pro) on my laptop and encountering the same errors, I realized that the problem had to be with one or more of my assets and not my new version of FCP, since my PowerBook is running FCP 5.0.4 and my Mac Pro is running FCP 5.1.2.
In my case the "corrupt" file was a Photoshop PSD file. In the past (FCP 4.5) I was able to use PSD files with hidden layers. I would merge the visible layers into one layer, keep the hidden layers and save the file. Once in FCP, I imported the PSD file and kept right on truckin'. I've done this for years. For some reason now with FCP 5.1.2 (and 5.0.4), that's not flying anymore. Once I "Flattened" the PSD file in Photoshop (deleting all of the hidden layers) I was able to build the project without any errors.
Interestingly, the technique I used to figure out which file was "corrupt" also allowed me to salvage parts of some of my "lost" sequences. I saw this posted in a forum at Creative Cow (creativecow.net). Basically, I opened up the project, clicked the OK button after the File Not Found error, went into the Browser, right clicked on the offending sequence, selected "Make Offline". When I double clicked the sequence it opened in the timeline with all of my assets offline. Then in the timeline, one by one, I right clicked on each clip and selected "Reconnect Media". Once I linked up the media, if I didn't get an error message, I would save as a new project (to salvage what WAS working), and go to the next clip. I did this until I found the offending PSD files.
I hope this helps. Now it's time to play "catch-up"
Mac Pro 3Ghz, 1GB RAM, ATI Radeon X1900 XT Mac OS X (10.4.8)

Itunes 10.4 not launching when connecting iphone

Snow Leopard 10.6.8. Just updated iTunes to 10.4. iTunes will not launch when connecting the iPhone to my MacBook Pro. Once connected, manually opening iTunes will allow the sync to happen, but only then. iTunes helper app is there in Login items.
Minor inconvenience, but could be a problem if I miss too many syncs due to this.
Any thoughts?

I had the exact same problem upgrading iTunes to 10.4 on Snow Leopard. It looks like there's a problem with iTunesHelper under Login Items. I found the solution here: https://discussions.apple.com/message/15666966 Simply follow the instructions to re-add iTunesHelper to Login Items, restart, and you should be good to go!

Stored procedure not found when creating a new recordset binding in Dreamweaver CS6 with ColdFusion Server 11

Stored procedure not found when creating a new recordset binding in Dreamweaver CS6 with ColdFusion Server 11. I can see the tables and views in the database tab, but no stored procedures. If I connect to a data source created in ColdFusion Server 6 I am able to see the stored procedures.

Ben thanks for the reply!
Yes that is the process I am following:
In Dreamweaver, open the page that will run the stored procedure.
In the Bindings panel (Window > Bindings), click the Plus button, and then select Stored Procedure.
In the Data Source pop‑up menu, select a connection to the database containing the stored procedure
Enter the ColdFusion Data Source user name and password.
At this point in the procedure drop down I would get a message that said No Stored Procedure Found.
Right now it appears to be working, I had to create a new site that pointed to the older CF 6 server's data source and create a page following the process above, then when I went back to the CF 11 site the stored procedures were now populated. I need to make sure it is pulling from the correct server but right now it appears to be working.
Thanks
Dwight

Error oracle.sql.* and oracle.jdbc.driver.* not found when using oracle as a database

I am using oracle as database and weblogic 4.5. I have copied the classes12.zip file in lib directory of weblogic. I am getting the error that oracle.sql.* and oracle.jdbc.driver.* not found when i am importing these packages in a jsp file. what i need to do to import oracle driver packages?I put it in the classpath also.
Please Advice!
Thanks in advance
AnuPama

Hi Anupama,
First of all I would be surprised if you would not like to use the connection pooling feature of weblogic (in which case you might not be needing the import the classes directly), and would like to open direct connections to your database. Anyways for doing that I would recommend you to check out the readme doc that ships
along with the jdbc oracle (classes12.zip etc). I am giving an excerpt over here:
These are a few simple things that you should do in your JDBC program:
1. Import the necessary JDBC classes in your programs that use JDBC.
For example:
import java.sql.*;
import java.math.*;
2. Register the Oracle driver before before calling other JDBC APIs.
(This is not needed if you are using the JDBC Server-side Internal
Driver because registration is done automatically in the server.)
To register the Oracle driver, make sure the following statement
is executed at least once in your Java session:
DriverManager.registerDriver(
new oracle.jdbc.driver.OracleDriver());
3. Open a connection to the database with the getConnection call.
Different connection URLs should be used for different JDBC
drivers. The following examples demonstrate the different URLs.
For the JDBC OCI8 Driver:
Connection conn = DriverManager.getConnection(
"jdbc:oracle:oci8:@<database>",
"scott", "tiger");
where <database> is either an entry in tnsnames.ora or a SQL*net
name-value pair.
For the JDBC Thin Driver, or Server-side Thin Driver:
Connection conn = DriverManager.getConnection(
"jdbc:oracle:thin:@<database>",
"scott", "tiger");
where <database> is either a string of the form
<host>:<port>:<sid> or a SQL*net name-value pair.
For the JDBC Server-side Internal Driver:
Connection conn = DriverManager.getConnection(
"jdbc:oracle:kprb:");
Note that the trailing ':' character is necessary. When you use
the Server-side Internal Driver, you always connect to the
database you are executing in. You can also do this:
Connection conn
= new oracle.jdbc.driver.OracleDriver().defaultConnection();
Hope this helps,
Thanks,
Anupama wrote:
I am using oracle as database and weblogic 4.5. I have copied the classes12.zip file in lib directory of weblogic. I am getting the error that oracle.sql.* and oracle.jdbc.driver.* not found when i am importing these packages in a jsp file. what i need to do to import oracle driver packages?I put it in the classpath also.
Please Advice!
Thanks in advance
AnuPama--
Apurb Kumar

I keep getting result code -43 not found when trying to load certain instruments. Any idea why

I keep getting error code -43 not found when trying to load certain instruments. Any ideas?

Errors 3000-3999 (3004, 3013, 3014, 3018, 3164, 3194, and so on): Error codes in the 3000 range generally mean that iTunes cannot contact the update server (gs.apple.com) on ports 80 or 443.
Update to the latest version of iTunes.
Verify the computer's date and time are accurate.
Check that your security or firewall software is not interfering with ports 80 or 443, or with the server gs.apple.com.
Follow Troubleshooting security software. Often, uninstalling third-party security software will resolve these errors.
An entry in your hosts file may be redirecting requests to gs.apple.com (see "Unable to contact the iOS software update server gs.apple.com" above).
Internet proxy settings can cause this issue. If you are using a proxy, try without using one.
Test restoring while connected to a known-good network.

Import not found when deploying to Standalone OC4J

Hi,
I'm developing a small application, consisting of a few classes and a few jsp pages. I'm using JDeveloper 9.0.3.1 with the sun j2sdk 1.4.2 for windows.
I test my application with the embedded OC4J in Jdeveloper, and it runs fine. But when I deploy it to the standalone OC4J, I get this error:
500 Internal Server Error
OracleJSP: oracle.jsp.provider.JspCompileException:
Errores de compilaciÃ³n:F:\programas\Oracle\jdeveloper\j2ee\home\application-deployments\Workspace4-WSWrappers-WS\WebServices\persistence\_pages\\_integrate2.java
Note: sun.tools.javac.Main has been deprecated.
F:\programas\Oracle\jdeveloper\j2ee\home\application-deployments\Workspace4-WSWrappers-WS\WebServices\persistence\_pages\_integrate2.java:6: Class webservices.Integrator not found in import.
import webservices.Integrator;
^
1 error, 1 warning
This error does not happen when using the embedded OC4J server, only when deploying to the standalone. Since leaving JDeveloper up all times to use de app is not an option :) I really would appreciate any help towards solving this matter. I suspect it has to do with deployment options and whatnot, but I can't find anything wrong. Of course, I'm fairly new to this (jsp/OC4J), so it can be an obvious mistake right under my nose.
thanks
Javier

Fixed. The problem was my Standalone OC4J was not properly installed, AND I was doin the deplyment wrong. Now it works by creating a war file, deploying to the war file and THEN deploying to the OC4J Standalone connection.
So, if you start seeing "import not found" when deploying to standalone and it works on the embedded, check you war files to see if they REALLY are packing the classes they are supposed to carry.

Ipad not found when connected to laptop

Similar Messages

Maybe you are looking for