IPad Sound works only with Headphone.

My Ipad 3 sound is gone and it is only audible via headphone. I have reset the settings once but of no use.
Also I rebooted the iPad couple of times by holding down the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears, but this was also of no use.
Any help in this regard full be highly appreciated.
Regards
Abbas

1. Double-click the Home button and swipe the Task Bar (at bottom) to the right. Check volume and mute settings.
2. Hold the Sleep and Home button down for about 10 seconds until you see the Apple Logo
Note: Try the reset a few more times if necessary

Similar Messages

  • My Pokerist app sound does not work, only with headphones....can anyone help me? Thank you

    My Pokerist app sound does not work.  It will only work if I have head phones on.  All other sound works, songs, video etc.  I deleted the app, then installed again still no sound.  It is not the app because I also have a IPhone and the sound works on Pokerist.  If anyone can help me I would appreciate it.
    Thank you
    Smartypants0

    Check out this link - http://support.apple.com/kb/HT4085.  There have been instances where settings have accidentally changed. Double click on the Home button, swipe all the way to the right to reveal the leftmost icon and alternate settings if necessary.

  • IPad WiFi works only with WPA/TKIP, not WPA2/AES

    My iPad (like so many others) stopped connecting to my Linksys WRT54G router (which like everyone else's connects fine with every other device, including non-iOS 4 iPhones). The whole reset/restart/restore dance with the iPad/router/cable modem was performed to no avail. By sheer desperation, security protocols were changed, and that's what finally worked.
    The protocol to the rescue was WPA/TKIP, curiously enough. (When security is completely disabled ("Open"), the iPad also connects, perhaps expectedly.) The culprit is WPA2/AES (even AES+TKIP). Any iteration of WPA2/AES ends up blocking the iPad from getting the appropriate IP address via DHCP. Once I changed to WPA/TKIP, everything's been rock-solid and fast.
    (The only times WPA2/AES worked was when the iPad was first used for a couple days, and a couple days after switching back to WPA2/AES when it started working with WPA/TKIP. Since then, switching back to WPA2/AES no longer works, even temporarily.)
    Any idea why initially WPA2/AES worked, and then suddenly stopped?

    Ralph Landry1 wrote:
    That is a very interesting question ... [involving] the combination of the router and the iPad and their respective implementations of the AES encryption algorithm. The AES algorithm is considerably more complex than TKIP. Why some have problems and not others has to be related to the router and its implementation and the Apple implementation.... t works fine for me connecting with [both] a Verizon FiOS (Actiontec) router [a]nd ... an AirPort Extreme. But there have been a number of posts recently about problems with Linksys and Belkin connectivity.
    Tell me about it. I'd been pulling my hair out prior to "discovering (by accident," as George Costanza would say) that WPA/TKIP fixed the problem, and seems to be working fine and fast. Now I'm just academically frustrated (better than actually frustrated) wondering why WPA2/AES is so problematic +with this particular trifecta+ (my iPad, my Linksys router, and WPA2/AES).
    Bottom line is there is probably not an easy solution ... and since you do have a strong security protocol that works, keep using it. Very strange that there would be a change in connectivity after a few months, though. Old engineering philosophy, if it ain't broke, don't fix it. If you have something that works, stick with it for now.
    Actually, WPA2/AES worked on two (short but notable) occasions:
    a) for two days when I first unpacked the iPad, and
    b) for two days when I switched back to WPA2/AES upon discovering WPA/TKIP fixed the issue.
    So it wasn't two months, which makes more sense. I agree with you that I'm not touching this arrangement for now. What I did have to do was change over the other devices (PCs, Wii's, TiVo's) that didn't automatically adjust over to WPA/TKIP. (To its credit, the iPhone did that on the fly.) Going through each device hurt a little, knowing I was using a less-than-optimal protocol for just one cranky device at expense of every other one--but of course I'd rather everything play nice than be necessarily cutting edge. (It's not like I'm the Pentagon or anything here.)
    But also give feedback to Apple:
    http://www.apple.com/feedback/ipad.html
    Done and done. And thanks for a great and reassuring explanation.
    Message was edited by: TashTish

  • HT1430 my ipod volume work only with headphones

    my ipod volume show only headphones....speakers not working

    Everyone's having this problem with their 4th generation's.. I think it's because of the software, but I could be wrong.

  • There is no sound in my ipad 3 , It works only with my headphone

    There is no sound on my ipad 3 , It works only with my headphone. I will try everything reboot several times .

    Are you turning up the volume after you take the headphones out? The iPad will remember two different volume settings, one with headphones and one without.

  • I have no sound in my computer, only with headphones, i tried the software update but it still doesn't work, and i have a red light on in my computer.

    I have no sound in my computer, only with headphones, i tried the software update but it still doesn't work, and i have a red light on in my computer. How to resolve that  ?

    Plug and unlpug the headphone jack with some intention to get the mechanical switch to flip.
    You can google for more intrusive methods. 
    ex. Read through all the many approachs: http://www.ifixit.com/Answers/View/8797/Audio+jack+problem,+no+speaker+sound,+re d+light

  • IPad 3 no sound speakers only on headphones. HELP!

    Hello everyone!
    Please help me, I have an iPad 3, that I bought for my boyfriend on june 2012, after over a year of use, everything had worked perfectly till' now. The iPad started to have problems with sound through speakers, every time it were less and less what you can hear, and then we started using headphone to hear better. Suddendly the sound went out, and now we have NO SOUND on speakers, only on headphones, BTW the microphone works!
    We have tried everything, nothing makes the sound come back.
    I have tried the following:
    System restore
    iPad reset (soft reset, hold home and lock buttons for about 15 seconds till apple comes up)
    Clean the headphone jack
    Clean the charger cable and connector
    Change the side switch from screen rotation to mute and viceversa
    Use control center to mute / unmute
    Change volume control to buttons and viceversa
    Reset all settings
    Erase all content and settings
    Use of Assistive touch to manually turn up volume, unmute and mute, etc...
    The sound comes only from headphones, and works perfectly with them, we have sound on games, notifications, music and everything else, it's just that sound doesn't come out from speakers.
    The problem started since september, when the iOS 7 update was done.
    But it got worse over the 7.0.4 update...
    Any ideas on how to fix this?
    Pleaseeee help!

    Were you ever able to resolve this? I have this issue as well. Have not done a restore, but have cleaned connecter and headphone jack. No success.

  • No sound but it works well with headphone

    Dear all,
          Can anybody fix my problem. I bought iPad 1 year 8 days back. My iPad external speaker has stopped working.however it works well with headphone. I have tried all methods like holding home and sleep button for ten seconds,reset to factory setting,all other trial given in differ
    ent forum but in vain. Now can anybody tell me what shall I do. Also since it is more than 1 week after expiry of warranty will apple help me to fix the problem.

    Satellite 1710CDS
    just upgraded to windows xp.
    Even if you max out the memory to 160 MB, it's too small for XP to run properly. Not surprised you can't locate drivers for XP.
    You can, however, find the drivers for Windows 2000 (which I prefer to XP anyway). The sound driver is included.
    Go to the Canadian download site and look up the Satellite 1710CDS.
    -Jerry

  • My iphone 5c the sound doesn't work only with earphone.

    my iphone 5c the sound doesn't work it works only with earphone.

    Hi there lavodette,
    You may find the troubleshooting steps in the article below helpful.
    iPhone: No sound or distorted sound from speaker
    http://support.apple.com/kb/ts5180
    -Griff W. 

  • HT1766 Have sound only with headphones after apples new IOS install, any help would be appreciated.

    Have sound only with headphones after apple latest iOS install, any help out there?   

    http://support.apple.com/kb/TS2802

  • Recently, I can't get any sound from my game applications.  Sound works fine with video, streaming, etc, but not my game applications.  I've tried powering down and re-booting, but the sound does not return.  Can anyone help me?

    Recently, I can't get any sound from my game applications.  Sound works fine with video, streaming, etc, but not my game applications.  I've tried powering down and re-booting, but the sound does not return.  Can anyone help me?

    Have you got notifications muted ? Only notifications (including games) get muted, so the Music and Videos apps, and headphones, still get sound.
    Depending on what you've got Settings > General > Use Side Switch To set to (mute or rotation lock), then you can mute notifications by the switch on the right hand side of the iPad above the volume switch, or via control centre : swipe up from the bottom edge of the screen and it's the right-most of the 5 icons in the middle of it (if the icon is white then it's 'on', tap it to turn it grey and 'off'). The function that isn't on the side switch is set via control centre instead : http://support.apple.com/kb/HT4085

  • Need some help! My iPhone 4 cannot play music through it's built in speaker, only with headphones. I also cannot adjust volume, it only shows "ringer". I really do not know when it starts. I already clean the jack and dock,reset it. Update it to IOS 7.1.1

    Need some help! My iPhone 4 cannot play music through it's built in speaker, only with headphones. I also cannot adjust volume, it only shows "ringer". I really do not know when it starts. I already clean the jack and dock,reset it and still cannot be fixed. I updated it to IOS 7.1.1 recently only, does it have connection with the inconvenience I am experiencing right now? What should I do? Thanks!

    Hi Melomane1024,
    If you are still having issues with your iPhone’s speaker, you may want to look at the steps in this article -
    iPhone: No sound or distorted sound from speaker
    http://support.apple.com/kb/TS5180
    Thanks for using Apple Support Communities.
    Best,
    Brett L

  • Audigy 2 ZS+Sounds works only if mediaplayer has played some video and you leave mediaplayer

    sounds work only in movies with mediaplayer..i have installed ffdshow what pops up when i start videos..if i try to play winamp only, music plays only -2 second and stops but with mediaplayer on backround it will play mp3..
    in mediaplayer sounddevice is audigy 2 but winamp directsound output is working only with primary sound device, if i change it to audigy 2 then the music stops
    also tryed dxdiag and there sound page..it plays directsound test only if mediaplayer is on..without mediaplayer nothing but at music page it plays that test without mediaplayer on in backround
    Even reinstalling WIN XP didn't help..same thing with audigy 2 cd full installion
    Can anyone HELP me..And sorry about my bad english
    Motherboard is DFI Ultra-D

    My guess is that your PowerDVD and WinDVD versions don't have ES support and you're using the programs to decode. This might be the case if you are configuring the programs for multiple speakers. If you are, try configuring them for SPDIF output, then make sure the soundcard is configured to decode AC3/DTS (it probably is). Does that help?
    -Dave
    [email protected]

  • Can hear my iphone only with  headphones .

    Can hear my iPhone only with headphones. 

    Hi, Valentino_Klein.  
    Thank you for visiting Apple Support Communities.  
    I would need a little more information or clarification of this issue to provide a better answer.  However, take a look at the article below as it may help with your scenario.  
    Get help with hardware features on your iPhone, iPad, and iPod touch
    -Jason H.  

  • Is there anything like smartbookmarks on mozilla newest version, because the smartbookmars tool works only with mozilla 3,6?

    ''Duplicate post, continue here - [https://support.mozilla.com/en-US/questions/806366]''
    Is there anything like smartbookmarks on mozilla newest version, because the smartbookmars tool works only with mozilla 3,6?

    The Smartbookmarks page refers to this add-on in its place:
    https://addons.mozilla.org/en-US/firefox/addon/roomy-bookmarks-toolbar/
    I have no idea if it's basically the same or anything about its reliability.

Maybe you are looking for

  • Shuffle (2nd Gen) not been used for a few years - not working at all - any ideas?

    My Ipod Shuffle (2nd Gen) has not been used for a long time and now will not give any reponse at all. It won't charge and it is not recognised by ITunes - is there anything I should do?

  • Security Mode Feature in ATAPI HD's provided by Apple

    Hello, I'd like to know how would I implement the security mode feature for the hard drive provided by Apple in MacBook Pro and if it will or not have any problems with EFI. How will EFI manage this feature of ATA hard drives?

  • ADOBE - Why is the meta "viewport" tag missing from the jQuery Mobile Web starter pages?

    Hi - I'm just starting to play with mobile and responsive web design.  I worked out a mobile version of an existing site which looked good locally but when I uploaded it the site appeared miniaturized and not optimized for small viewports.  All the t

  • Create empty Document with DOM level 3

    im trying to create an empty document using the DOM level3 api, and am not sure how to do it. i can parse an existing document using an LSParser etc, but not sure if i can use the same implementation to create an empty document, there seems to be no

  • Web service, best practice

    Hi, I would need some oppionions on best practices for a WS interface. Lets say I have a system with 5 different states on an entity, lets say states are A, B, C, D and E. It is not possible to shange from any state to any other state, there are cert