Ipad system hang during itune upgrading

ipad system hang during itune upgrading

Recovery Mode
1. Disconnect the USB cable from the device, but leave the other end of the cable connected to your computer's USB port.
2. Turn off the device: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for the device to turn off.
3.While pressing and holding the Home button, reconnect the USB cable to the device. The device should turn on.
4. Continue holding the Home button until you see the "Connect to iTunes" screen. When this screen appears, release the Home button. iTunes should alert you that it has detected a device in recovery mode. Click OK, and then click Restore to restore the device.
Note: Data will be lost. You may have to repeat the above many times.

Similar Messages

  • Multiple cPCI Graphics cards - System Hangs during Boot

    We have 2 Kontron dual output CP332 cPCI graphics cards to install into a NI PXI rack in order to give us 4 graphics outputs.
    When one card is installed it acts as the Primary graphics card and it is required to disable to NI on-board graphics card in order for this to boot and function correctley.
    If a 2nd Kontron CP322 card is added the system will hang during WinXP boot, as it switches from VGA to SVGA mode.
    Disabling the 2nd card via device manager allows the system to boot.
    Re-enabling the 2nd card once booted, then configuring with the ATI driver application allows the 4 graphics output to work as expected.
    If the system is re-powered it will once again hang during WinXp booting.
    Is there anything that can be configured on the NI Embedded PC (BIOS) to prevent this ?
    Is there anything in windows that can be set to prevent this ?
    Can we control the windows device manager from labview in order to enable/disable the 2nd card after power-on and before shutdown.
    many thanks

    Hi Scott,
    I have some more information for you regarding your issue. We have tested the Kontron CP332 with the PXI-8196.
    However when we tested the setup, we had 3 monitors working, the on-board graphics and the dual output from the card.
    Until we get the on-board graphics working with a single CP332 I don't think we will get bot CP332's working.
    So these are the steps to get on-board graphics working with a single Kontron card the steps come from talking to our PXI Product Support Engineer:
    "The first thing you need to make sure is that you are using the
    driver for Windows XP, and not the one for Windows 2000. Here's a link
    to the driver download page:
    http://us.kontron.com/index.php?searchword=cp+332&id=363
    Notice that the first two driver downloads look just the same, but if
    you hover over them and look at the url, you'll notice that the first
    one is for Windows 2000 (w2k), and the second one is for Windows XP
    (wxp). So, just make sure you are using the second one. The PSE did
    mention that she was initially using the Win 2k driver, and was having
    some issues with it hanging and all. Here's the information she sent me
    about how she was able to get things working:
    "Here is the info. My controller has BIOS version 1.3 but have him try this first before updating the BIOS.
    The Kontron Board is the CP 332. I was able to get all three monitors working with the PXI-8196.
    Configuration steps:
    1) Insert both the controller and the kontron board in the chassis.
    Note: When the computer is starting it will give you the Windows boot
    up screen on the DVI 1 on the Kontron board and then give you the login
    screen on the monitor connected to the 8196 so make sure you still have
    a monitor connected to the controller.
    2) Cancel the NI installation wizard if it comes up.
    3)
    Unzip the drivers and run the setup.exe file. Make sure you install
    both the ATI display driver and the ATI Control Panel. (Check the zip
    name to make sure you have the xp version of the driver)
    4) After
    restart go to the Display Properties and under the Settings tab you
    should have monitors 1 and 2 on Mobility Radeon 9000 (Kontron CP-332)."
    If you don't have BIOS version 1.20 or higher, please upgrade to BIOS version 1.30, if you need to upgrade the BIOS please make sure you fully understand the readme file. Then follow the steps above to enable triple output on the graphics cards.
    When you have this working please try adding the second Kontron card.
    Regards
    JamesC
    NIUK and Ireland

  • Frequent iMac 3.06 hangs during iTunes usage

    I have an iMac 3.06Ghtz with 4GB RAM, 1TB and find I get random system freezes every few days.
    There is not one thing I can do to replicate the problem, but I'm sure it's iTunes related.
    It first started about 2 months ago when I was buying albums for download. Some downloads would complete, but then on some tracks it would hang. Upon restarting and trying again, some of the files would not be there to retry, so I'd have to ask Apple support to re-enable them. This eventually seemed to be sorted out in the last couple of iTunes updates.
    However, I still find that when iTunes starts playing a new track, often a few seconds in, iTunes stops and becomes unresponsive. It's completely random when it does this. After rebooting, playing the same track does not cause a hang!
    Finder appears ok to start with, but I can't launch any new programs and anything I now click on will hang.
    I can't bring up the force quit dialog. I can't even log in remotely via terminal to kill any processes.
    I have no choice but to do a hard reset every time.
    Upon reboot, there is no crash report notification and nothing obvious in the console.
    Things I've tried
    - Archive and reinstall
    - Repair disk / repair permissions
    - Re-install iTunes
    - Removed all startup programs
    - Hardware test (no problems)
    - Removed all USB devices
    I've had Macs for a few years now, but this is really bugging me because there's no logical thing to try to sort it out. Especially as it was the most expensive iMac available at the time! I've never had to reboot a computer as often as this in my whole IT career. Argghhh!
    Does anyone have any ideas please? Thanks.

    Try creating a new admin user account in System Preference Accounts pane.
    Log out and log in to the new account. Do you have the same issue in the new user account?
    If you do, there is a general system or hardware issue that needs to be further assessed.
    If you do not, there is a problem in your current main user account. You can continue to troubleshoot while narrowing the possibilities to something in your account, or you can transition to a new account.
    Note: An +Archive and Install+ will not fix a user account-related problem, because it preserves your existing user accounts.

  • HT1926 Error message during iTunes upgrading

    I try to upgrade iTunes on my PC to the latest version but in the middle of the installation process a box appears asking: "do you want iTunes to make changes to your computer?".  Regardless of what I press, the installation process gets interrupted with the message: "errors occurred during installation before iTunes could be configured".  What goes wrong here?

    Make sure you are installing iTunes from an account with Administrator privileges. If you can't get it to install then you may need to uninstall all Apple software, reboot, then try again.
    tt2

  • Imac hanging during Lion upgrade

    I have a 2010 27" imac.  As of last night, it had Snow Leopard on it (as it was shipped with).
    I tried upgrading last night with the Lion purchased from the App store.
    The system now appears hanging with "approximately 21 minutes left" on the screen.  The mouse works.  The screen dims after X minutes, and will wake up with mouse movement.  No keyboard inputs seem to work.
    It has now been 12 hours stuck at the same point. 
    What's next?  Power cycle?  Hope for the best?  I have plenty of backups, but I'm surprised that a newer system is having this problem but I can't seem to find others who also had it.

    I did do the above as I read that may work too, I also made it so the HD never sleeps.  Did not help for me, computer still freezes when switching accounts, not all the time, on average every other day I need to do a hard restart.
    Still looking for the answer

  • System hang during installation of Solaris 10

    Dear all,
    Solaris 10 x86 6/06 installation on Magic-Pro MP-P6PE-1000
    mainboard.
    I have tried on PC and VMware 5.5.1, but fail the installation.
    Moreover, I have tried append "-kd" at "kernal ...cdrom" in GRUB edit mode, and then boot the system.
    type "use_mp/W 0 :c"
    But it still hang at:
    SunOS Release 5.10 Version Generic_118855-14 32-bit
    Copyright 1983-2005 Sun Microsystems, Inc. All rights reserved.
    Use is subject to license terms.
    or
    configuring devices
    hang!!
    I've also try disable/enable ACPI, but no success.
    Have any ideas?
    Thanks!

    Try to boot the kernel with the "-v" option, any maybe even set
    "moddebug to 80000000", so that we can get a better idea
    where it is hanging.
    Check the following web page for details:
    http://blogs.sun.com/roller/page/dmick?entry=diagnosing_kernel_hangs_panics_with

  • System Sleep During iTunes Play

    Why doesn't iTunes override my system sleep settings when it's playing music? When iTunes plays videos, the computer stays awake regardless of sleep settings; why won't it stay awake when playing music?

    Why doesn't iTunes override my system sleep settings when it's playing music? When iTunes plays videos, the computer stays awake regardless of sleep settings; why won't it stay awake when playing music?

  • Sybase 16.0.00.01 hang during SUM upgrade.

    Hi
    Yesterday installed fresh SolMan 7.1 on Win 2012 with Sybase ASE Adaptive Server
    Enterprise/16.0 GA PL01/EBF 22540 .Kernel 721EXT PL 201 and lib_dbsl
    213.
    Now performing upgrade to SP11 using SUM SP10PL6
    During phase MAIN_NEWBAS/RUN_RSCPFROM_CRR database freeze and i'm unable to login with isql:
    I'm observing very high CPU usage ~70% without any disk activity.
    The only solution is to restart db service and then db is accessible.
    Updated db parameters with latest script from note 1602547 - nothing
    helped.
    It's my first Sybase ASE installation - so i'm rather green in this db
    Opened ticket 499958 / 2014 - if anyone from support want to log into WTS and rerun this step to catch logs i'm ready.
    Regards
    Marcin

    Hi Marcin,
    Please check the below SAP notes and perform recommendated steps
    1) 1581695 - SYB: Configuration Guide for SAP ASE 16.0
    2) 2006403 - Very High CPU Usage with ASE 16.0 on Solaris
    Refer to the CR note mentioned under SAP note 2006403.
    Hope this helps.
    Regards,
    Deepak Kori

  • Bad estimate of iPad available memory during iTunes Sync

    All my music is in apple lossless format. When synchronizing with iTunes , I check the option to convert to 128 kbps. iTunes does the conversion however the available memory estimate is done using the full size of lossless format. As a result my iPad is half empty since Itunes believe it is full and refuse to synchronize more stuff.
    I did have this issue with earlier versions of iTunes (9.x).
    I went to a genius bar, but they had no clues...

    Bad wording, I didn't have this issue with iTunes 9.x, but have it with iTunes 10.x and 11.x

  • Occasionally system hangs during eject of DVD-drive

    I have an irritating problem where I cannot get rid off (yet).
    When I am burning cd on nero (latest version) the system starts to hang when the DVD-drive is ejecting the CD -> I have to restart the comp.
    Same when I use DVD Decrypter, when I create an ISO file on the hard drive from DVD. It starts to hang when he ejects the DVD.
    I started to play around with the automatic eject settings on the drive itself and in the programs and try to set it to "do not eject", but it does't work.
    Any hints/ideas?
    .

    Thanks for the input.
    I did not do so much until now...(time)
    But what I did is send an email to Nero tech support with all the information included from all there Info utilities, which should help answering some support questions. I can tell you that the support is probably just as "good" as MSI's support. It took them 4 days to send a non helpfull answer... and I had to remind them about the request as well.
    I now have latest version of Nero (6.3.1.15) and the drivers from Mega 180 cd.
    I assumed that the drivers from my Mega 180 cd were the same from the web (2004-2-17) and that the less helpfull drivers -mentioned in the link by you Normunds- were shipped together with bios 3.0. (I have standard 3.30). But maybe that isn't so...
    Anyway Mishima, you have the drivers from the web right (ITB)? And you have let's say half my problem..hmmm
    Probably I will try out the following, and if the first of them doesn't help I take the next point and so on:
    * Install NEC 2500 latest firmware 1.07
    * Install the drivers from the web -ITB- (2004-2-17)
    * Install the drivers nVidia nForce 4.24 WHQL
    Does anyone have experience with nVidia nForce 4.24 WHQL drivers ??
    (http://www.nvidia.com/object/nforce_udp_winxp_4.24)
    .

  • System hangs during shutdown, blue screen with gear spinning.

    My MBP gets stuck during shutdown/restart process.
    The system acts like it is shutting down, exits the the desktop, goes to a blue screen with a spining gear then never turns off.  It seems the screen falls aslep if you leave it awhile but the system itself won't actually shutdown. If you move the mouse the screen lights back up. but still shos the "death gear"! happens on both shutdowns or restarts.  System must be turned off by holding the power switch for 10 secs.
    Please help!
    Chris

    Seems like a odd thing. If youve downloaded torrents of hacked programs or things like that may have been the cause by the uploader hacking and doinng this. I would bring the Macbook Pro to the apple store and see what they can do. If they cant do anything about it I would backup all the important programs and get rid of anything that seems suspicious. Then upload the stuff back onto the computer after you restore it. Thats the best solution.

  • Errors occure during iTune upgrade

    I checked for available updates and was informed that new version 11.0.2 of iTunes is available. After selecting "Install" updated was downloade. While in installing stage of updating iTunes I get a message: "An errors occured while installing the update, Choose Tools > Download Only and install manualy".
    Did not tried suggested solution since I could not find "Tools"
    Anyone knows the solution?
    Thanks

    Hello
    Use the Control Panel to uninstall iTunes and related software components in the following order and then restart your computer:
    iTunes
    QuickTime
    Apple Software Update
    Apple Mobile Device Support
    Bonjour
    Apple Application Support
    go to http://www.apple.com/itunes/download/ ... to download and reinstall iTunes

  • My ipad 2 hangs during software download

    how do i restart the device the icons are not working, switch off bar does not slide because of the error message left on teh screen posted

    See your duplicate thread : https://discussions.apple.com/thread/4252752?tstart=0

  • IPod/iTunes 6 hangs during updating

    I've just spent most of a weekend trying to figure out why a 40GB click-wheel iPod will not sync with iTunes. I'm at a bit of a loss here. I know there are several (long) posts on update issues - perhaps this is just another case. Here's the low-down:
    Gear:
    * iPod 40GB 'click-wheel' model, 3.1 firmware (2005-09-23 update), firewire interconnect direct to iMac (no dock)
    * iMac G4 1GHz, OS X 10.3.9, iTunes 6.0.1, about 1600 songs
    Symptom:
    iPod appears on the desktop and can browse folders. iTunes starts. Hangs during iTunes update on a random song. Usually <20 into the list - but sometimes anything up to song 1000. Flashing 'do not disconnect' symbol freezes on iPod LCD, iMac hangs (Activity Monitor indicates a >90% cpu load on iTunes process, generally requires a 'hard' restart to recover the iMac - even after force-quitting the iTunes process).
    Tried:
    * Reset iPod
    * Restore iPod with 3.1
    * Restore iPod with 3.0.2 (2005-06-26)
    * iPod into disk mode and restore
    * iPod disk verify and erase using OS X Disk Utility, restore firmware
    * New firewire cable
    * iPod into diagnostics mode - run most tests including HDD scan (all pass)
    * iMac disk permissions verify/fix
    * Delete iTunes preferences and restart - library rebuilds
    * Copy music to a new location, delete all iTunes data, now start afresh and
    use add to library to rebuild library
    * Removed songs and entire albums that sync freezes on (just freezes on
    another song)
    * Checked out iMac firewire ports with iSight
    * Discussed with Apple Tech guy at Genius bar, agreed pretty much all steps
    had been covered. iPod exchanged believing something like iPod connector
    to be the issue. No difference.
    So I'm pretty much convinced at this stage the issue lies with the iMac software. iPod and cable have been thoroughly investigated and changed out. iMac firewire ports work with iSight.
    I've seen some posts suggesting deleting and restrong from the 10.3.9 update the iPod driver (iPodDriver.kext). This seems pretty drastic! I'm hesitant to go get a Tiger upgrade - this should work with 10.3.9.
    Apologies for the long post - but I'd be interested to hear views at this point.
    Thanks
    40GB click-wheel   Mac OS X (10.3.9)   iTunes 6.0.1

    Hey, you the man. I just want to say thank you. I hooked up a just repaired touch wheel iPod to my son's g4 iMAC, and it kept hanging on random songs and even the one's it transferred, it did slowly. I tried everything everyone else has, I did restores and erases forever. And it kept hanging up, so I had to frequently disconnect the iPod to get control back of the computer. This morning I was on the phone with Apple tech for over an hour. His conclusion was that because some of the songs weren't purchased from the Apple Store, I needed to manually transfer each song one at a time. I had to go, so didn't get to try it until later today and same problem. Again I called Apple tech support. Guy was very nice, on phone with him for 90 minutes, he didn't think the first advice made much sense. He gave up in frustration when we couldn't get into the disk utility because iPod kept going to automatic update. He told me to call back tomorrow and speak to a specialist. He said he's never had this much difficulty with an iPod. After the call, I managed to get into the disk utillity and do the erase and repair but didn't do anything. When I finally deactivated the auto update, manually transferring the songs one at a time didn't solve the problem. I read your post, started up after disconnecting the iSight firewire cable, took a chance of activating auto update of songs again, and voila, it transferred all the songs (all 176 of them) in about 10 seconds, like a warm knife through butter. And as they said on Saturday Night Live, it felt "like butter." I will call Apple tomorrow and tell them they really need to do something about this. In the meantime, I'll keep iSight disconnected whenever songs are being transferred into the iPod.
    Again, your advice is much appreciated. Thank you for the post.
    Steve
      Mac OS X (10.4.3)  
      Mac OS 9.2.x  

  • System hanging on setup is starting service....

    Dear Friends,
    I have a new Fujitsu Desktop pc, Model No is Esprimo P400 E85+. When the open
    windows 7 on this computer will come a error message like this " This computer restarted unexpectedly or encountered an expected error. Windows installation cannot proceed. To install windows, click OK to restart the computer, and then restart the installation
    ". and keyboard and mouse also not working that time. That why I cannot access shift+ f10 or registry edit... How can I fix this problem without format Because inside recovery partition . Please help me... I am waiting for your replay
    Advanced thanks for your reply
    Thanks 

    Hi,
    Did you perofrm a factory reset with the recovery partition? According to your description, the system hangs during the installation, and the keyboard\mouse both malfunction, in this situation, I'm afraid that we need to power off the machine and re-do
    the setup. Unplug all external device except keyboard\mouse. By the way, what is the reason that you want to use recovery partition, as
    arnavsharma mentioned already, when a system is malfunction, before using the recovery partition, have you tried other recovery options in recovery console, such as Last known good config\startup repair\system restore ? Any result?
    http://windows.microsoft.com/en-hk/windows/advanced-startup-options-including-safe-mode#1TC=windows-7
    Yolanda Zhu
    TechNet Community Support

Maybe you are looking for