Ipad wheel turning plugged into itunes message error 0xE8000065
Ipad2 is showing the wheel only on screen, then plugged into computer itunes states doesnt recognise error message 0Xe8000065. Please help!!!!!
( *click on image to enlarge* )
JGG
Similar Messages
-
my ipad says to plug into itunes but when i do my computer tells me to unlock my ipad but i can not do so
Have you a passcode set? Enter the number!
-
When my iPad prompted me to upgrade to IOS 7.1, I selected the upgrade. All went well until the iPad prompted me to plug into iTunes. I plugged it to a laptop, then the message on the laptop stated "iPod is in Recovery Mode" Nothing worked to get the iPad to complete the upgrade, not even an attempt to restore iPad to factory settings - it is stuck in the "plug to iTunes" mode.
Any suggestions to either uninstall IOS 7.1, to complete the install, or to reset it? At this point, it is a $700 papeweight.Pad: Unable to update or restore
http://support.apple.com/kb/ht4097
iTunes: Specific update-and-restore error messages and advanced troubleshooting
http://support.apple.com/kb/TS3694
If you can’t update or restore your iOS device
http://support.apple.com/kb/ht1808
Cheers, Tom -
Tried restoring my iPhone 4s iTunes said it couldn't restore it and now iTunes won't recognize it and the screen is frozen on the plug into iTunes message
iOS: Unable to update or restore
-
Picture of usb plugging into itunes, received error while updating software for ipod touch
tried updating software on new (refurb) ipod touch. everything was going ok with updates, when it was almost complete i received an error. now i have a picture of itunes with a usb cord plugging into it and it won't do anything else. accessed itunes through firefox. any suggestions?
Try here. iPhone and iPod touch: Unable to update or restore
-
I get an error message with I try to plug into itunes;
This iPhone cannot be used because the Apple Mobile Device service is not started.http://support.apple.com/kb/TS1567
-
helpppp
I dropped my iPhone 5 and it doesn't turn on it just shows the apple and says to plug into iTunes.. then i restore it and it says error , what do i do to get my phone to turn on fully ?See if this helps: http://support.apple.com/kb/TS3694#USB
If it does not help, the drop probably damaged something inside the phone. -
My ipad is flat and when I plug it in to charge it just repeatedly turns on and then turns off but isn't charging. I tried to plug into itunes but it just goes through the same ritual and can't maintain connection to itunes. What should I do ?
1. Reset iPad
2. Try another wall socket
3. Try another cable (make sure it's an original Apple cable)
4. Try another charger (make sure it's an original Apple charger)
5. Clean Lightning port with compress air or new paint brush -
BF tried to update to ios6 on iphone 4 but crashed half way through saying it needed to plugged into iTunes and then restored so after it was 'restoring' he had an error message come up say to couldn't be restored....what should be do next as the phone is in a complete non working condition
Spent hours trying everything suggested and finally this morning hit on a solution. iTunes must be run as an administrator. Even though you are logged into your PC as an administrator, using the iTunes shortcut does not make you an administrator in iTunes. I found this out by using the diagnostics in iTunes and reading through the results report.
I am using Windows 7, so I clicked the start button and right clicked on iTunes and selected "Run as an adimistrator". The first restore attempt got the 4013 error. I then did the DFU thing, hold power and home buttons for 10 seconds, release power and continue holding home for 10 more seconds.
iTunes gave me the restore message and I clicked it. I clicked the restore iPhone button and it started. The drivers loaded a couple of times. I got the apple logo with the progress bar and this time instead of disappearing, it started to fill in.
End result, a successful restore to factory settings and a happy 14 year old.
Hope this helps others. -
My phone is telling me to restore it as it will not come on and just shows a plug into itunes sign...however there is an error restoring it. HELP?!
You might try:
Placing your device into recovery (DFU) mode:
Follow these steps to place your iOS device into recovery mode. If your iOS device is already in recovery mode, you can proceed immediately to step 6.
1. Disconnect the USB cable from the iPhone, iPad, or iPod touch, but leave the
other end of the cable connected to your computer's USB port.
2. Turn off the device: Press and hold the Sleep/Wake button for a few seconds
until the red slider appears, then slide the slider. Wait for the device to turn off.
* If you cannot turn off the device using the slider, press and hold the
Sleep/Wake and Home buttons at the same time. When the device turns off,
release the Sleep/Wake and Home buttons.
3. While pressing and holding the Home button, reconnect the USB cable to the
device. The device should turn on. Note: If you see the battery charge warning,
let the device charge for at least ten minutes to ensure that the battery has some
charge, and then start with step 2 again.
4. Continue holding the Home button until you see the "Connect to iTunes" screen.
When this screen appears you can release the Home button:
5. If necessary, open iTunes. You should see the following "recovery mode" alert:
6. Use iTunes to restore the device.
If you don't see the "Connect to iTunes" screen, try these steps again. If you see the "Connect to iTunes" screen but the device does not appear in iTunes, see this article and its related links.
Additional Information:
If you have a problem getting into recovery mode then try: RecBoot: Easy Way to Put iPhone into Recovery Mode.
Note: When using recovery mode, you can only restore the device. All user content on the device will be erased, but if you had previously synced with iTunes on this computer, you can restore from a previous backup. See this article for more information. -
My ipad has been locking up and shutting down when I'm using the internet. Went to do upgrade 6 and Ipad froze wanting me to plug into itunes. I hooked ipap up to my laptop to do upgrade, but the ipap was still frozen, I had to restore to factory settings, unfortunately I have lost my pictures. Is there anyway to get the pictures back?
Pad: Unable to update or restore
http://support.apple.com/kb/ht4097
iTunes: Specific update-and-restore error messages and advanced troubleshooting
http://support.apple.com/kb/TS3694
If you can’t update or restore your iOS device
http://support.apple.com/kb/ht1808
Cheers, Tom -
im trying to update to newest ios version. but during the proccess, an unknown error accured, now the device wont do anything, just shows the plug into itunes screen. the device does not show in windows or itunes. the iphone wont do anything. i tried restarting, it shuts off and back on, but only shows plug into itunes thing. any ideas?
From my experience, the only way you're gonna get a PC afflicted with this disease to work with a 5th gen nano is to roll back to an earlier version of iTunes. Those affected have been exhausted by this ongoing issue. To update or not to update? And I always say never update unless you have to, and turn off all that auto update mess!
I have two core2duo lappies running 32b vista. My workflow dictates 32b fyi. One is acer aspire running itunes v 11.1 (.0.126), 5th gen nano was originally formatted and works just fine on this machine to this day. My other is the bigger badder lenovo thinkpad and the 5th gen will NOT mount using any version of itunes past 11.0 (.1.12) Windows mounts it just fine. itunes is not having it. no shirt no shoes no service.
I have both a 4th and 5th gen nano. The 4th gen works great on both machines, I even successfully tested it with the latest version (11.1.5) before subsequent deletion on the thinkpad! Weird huh? I think my next experiment might be to restore my 5th gen w/ a Mac and theeeeen plug it into PC itunez.
I'm at a loss on the thinkpad. Scanned for intruders. Cut the Lenovo bloat. Executed system and reg maintenance. Took down msconfig to a safe mode + itunes level to attempt to resolve possible sw conflicts but to no avail. NO NO NO. Every single dang port, every time on the thinkpad. Has me feeling like others might get the same treatment by the next itunes update. :|
So in summary for me:
5th gen nano and thinkpad are a NoGo on 11.1^ last working version for me = 11.0.1
5th gen nano is working on an acer aspire 11.1.0 but no way in the world am I updating
4th gen nano is kicking 5th gen nano's @zz so what would make me want to buy a new ipod? -
My ipad 3 is frozen on the plug into itunes page - it won't turn off or on - just stuck. I have tried to follow advice I have found on these pages but I don't know how to connect the ipad to my mac (the advice is to connect ipad to mac and there is no usb port on an ipad). If anyone could help it would be appreciated. Going nuts.
I think you should probably also read the iPad User Guide. You didn't say what version of iOS your iPad is running, so here's the links to both the iOS 6 and iOS 7 (PDF) versions:
iPad User Guide for iOS 6
iPad User Guide for iOS 7 -
I clicked the button in my setting thatz is saying "software update iOS 6.1.2. It turned off and now My iPad 2 is stuck on a black screen that has the iTunes symbol and a charger that I'm guessing means "plug into iTunes". I did so and then waited four hours to download something. And now it is saying that its going to update my iPad but it isn't working. I tried to "update" twice. I am VERY ANNOYED beczuse the last time i updated it, it just turned off and i didnt have ot plug it in or anything. WHY IS IT DOING THIS.....?????? My ipad will not turn on or anything. Help me FIX THIS!!!
hi Kinney. last hour, i update my ipad 2, then im having the same problems as u. im also hoping people can solve this issue.
-
I'm having trouble updating software for my iphone 4s from 5.0.1 to 5.1 but each time i plug into itunes to download it says network connection cannot be established and the phone just says an error has occured. What can i do?
If you don't have iOS 5, plug your iPhone into your computer, select it in iTunes, and in the Summary, click Check for Update.
If you do have iOS 5, it has onboard updates so you don't have to plug it in, just go to Settings, click General, click Software Update and you will be presented with iOS 5.1 which came out a few hours ago. Both my iPhone 3GS and iPad are already updated to iOS 5.1 now.
Maybe you are looking for
-
List with more than 1000 elements
I'm trying to use this query: select * from street where street_cod in ('street_code_list') It working well when the 'street_code_list' has less than 1000 codes but it fails when it have more, with a message that says that a list can't have more than
-
Major Monitor Issues in Finder
I was getting horrible refresh problems and artifacts in Finder. Here is what it looked like... http://i36.tinypic.com/e9dyqh.jpg So I zapped the PRAM and repaired permissions, now I am getting an oversaturation in the reds and cyans. Look at the pic
-
I am trying to license my recent download of Lightroom 5 onto my recently purchased Macbook with the serial number of the disk I purchased last year for my Windows PC (an upgrade from Lightroom 4). I receive an error "The serial number you entered i
-
Is my Spectrum 48k better than your Commodore 64k ...
And can my dad duff your dad up? lmao... Quality of postings seem to be hitting all time lows. Btw those Beta guys have a cool new Ovi Store App http://betalabs.nokia.com/apps/store-qml-client Check out the new Full length slim tapable Tool Bar at th
-
Problems installing Sol 10 x86 on Compaq Harware
Please Help! I am a newbie to Solaris and I am trying to understand some of these postings in this thread. I am trying to install Sol 10 on a Compaq DL360 with dual proc 1.26 MHZ and 3 GB RAM. It has an imbeded 5i array controller with two 36 GB driv