Ipad won't open past the apple screen

My Ipad won't open. I have pictures of my home that was damaged in the May 20 tornado and now I can't access them from my Ipad. Any suggestions how to get it to open?
It is stuck on the opening Apple screen

First thing to try is to reset your device. Press and hold the Home and Sleep buttons simultaneously ignoring the red slider should one appear until the Apple logo appears. Let go of the buttons and let the device restart. See if that fixes your problem.
If that doesn't help Make an appointment at an Apple Store to have your device examined by a technician. Or contact Apple Support.

Similar Messages

  • HT4528 My iphone won't go past the apple screen

    I was having difficulties with my iPhone 4 around 1ish eastern time so I decided that turning it off would help.. When I tried turning it back on it woudn't go past the apple logo. I decided it'd be best to let it rest. I've tried the recovery mode and it didn't do anything. I tried connecting it to my computer and it didn't do anything. Now 7 hours later I have it plugged in and it still won't go past the apple logo. Someone anyone.. Please help me!! Thanks in advance

    Try DFU Mode Restore. Open iTunes on computer. Connect iPhone to computer with USB cable. Hold both Home and Power button, after exactly 10 seconds release the Power Button, keep holding the Home button until iTunes recognizes iPhone in Recovery Mode, usually about 20 seconds time. If the iPhone screen is black, blank this is DFU Mode. Click the Restore button of iTunes.

  • IPhone 3G won't go past the apple screen

    My 3G is stuck on the apple screen after a reset

    You might have to put it into recovery mode and restore from backup.  See http://support.apple.com/kb/ht1808.

  • MacBook Pro won't get past the apple screen on startup

    The laptop won't startup. I get to the Apple logo and a spinning gear. I've tried starting it 3 times with the same result.

    Take each of these steps that you haven't already tried. Stop when the problem is resolved.
    Step 1
    The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.   
    There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
         a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
    b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
    c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
    Step 2
    If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use either of the techniques in Steps 1b and 1c to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
    Step 3
    Sometimes a startup failure can be resolved by resetting the NVRAM.
    Step 4
    If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
    Step 5
    If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
    Step 6
    Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
    Step 7
    If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
    Start up in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Post for further instructions.
    Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
    The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
    When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 10. If you ever have another problem with the drive, replace it immediately.
    If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
    If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
    Step 8
    Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
    This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
    Step 9
    Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
    Step 10
    Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
    Step 11
    This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
    Step 12
    If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

  • IMac won't reboot past the apple screen. 2009 10.6?

    My iMac wont reboot past the white apple screen! What do I do?

    Reinstall OS X without erasing the drive
    1. Repair the Hard Drive and Permissions
    Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
    If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
    2. Reinstall Snow Leopard
    If the drive is OK then quit DU and return to the installer.  Proceed with reinstalling OS X.  Note that the Snow Leopard installer will not erase your drive or disturb your files.  After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
    Download and install Mac OS X 10.6.8 Update Combo v1.1.

  • My Ipod won't go past the apple screen

    I unplugged my ipod from the computer and it was stuck on the "eject" screen, so I reset it, and now it just keeps reseting itself. It won't go to the main menu screen, it just keeps reseting and going back to the apple. I tried putting it in disk mode and restoring it, and it seemed to work, but then it just went back to resetting. And I tried to restore it again in disk mode, but now it says "Ipod cannot be found"

    I have the same problem. Anyone know how to fix it?

  • Won't load past the apple screen after a while it says "restart computer"

    It doesn't have a battery or a airport card would that be the issue

    More than likely the logic board is toast. In that case it would be cheaper to buy a pre-owned MacBook. If you kept the disks that were included when the computer was bought new, one of them includes the Apple Hardware Test. Use that to tell you what's wrong with the computer....
    Good luck!

  • PowerBook Won't Boot Past the Apple and Spinning Flower Screen...

    I've been reading a lot of these forums, but still haven't figured out how to fix it on my laptop. So, I made my own topic.
    Anyways. My dad gave me this laptop since he got a new one, so it's a hand-me-down which means I don't have this startup disk that I keep seeing talked about. I've tried Safe Boot, but when I do it with Command + V, it says all sorts of things that I just don't understand, and there is a lot of talk about the Apple Power Management? Such as:
    com.apple.driver.AppleIntelCPUPowerManagement isn't a valid mach-o (magic is cefaedfe)
    error mapping module file com.apple.driver.AppleIntelCPUPowerManagement
    can't map com.apple.driver.AppleIntelCPUPowerManagement in preparation for loading
    couldn't alloc class "AppleIntelCPUPowerManagement"
    Etc, etc. And then the last lines that it ends with say:
    BSD root: disk0s3, major 14, minor 2
    [HCIController][configurePM] power parent ready after 1 tries
    And it just stays there and doesn't boot up.
    I honestly don't know what any of this means, or if it is even relevant to why my PowerBook won't boot past the Apple screen. If you have any information on how I could fix it, that'd be great. Also, if you have any questions that would help you figure it out, ask away and I will answer them.
    Thanks a lot.
    Message was edited by: MixtapeChick

    MixtapeChick:
    Welcome to Apple Discussions. Congratulations on your "new" PowerBook. I suggest that you begin with this combination procedure:
    • Shut down the computer.
    • Locate the following keys: Command, Option, P, and R. You will need to hold these keys down simultaneously later.
    • Turn on the computer.
    • Press and hold the Command + Option + P + R keys immediately after the startup chime.
    • Hold keys down until you hear the startup chime for the third time.
    • Release the keys and immediately hold down Shift key to start up in Safe Mode.
    • Log in and empty Trash.
    • Restart normally and log in.
    Let us know how it goes.
    cornelius

  • I updated my first generation iPad to version 5.1.1 and won't go past the setup screen that asks if I want to use the iPad locator. I can go back but can't get any further.

    I updated my first generation iPad to version 5.1.1 and won't go past the setup screen that asks if I want to use the iPad locator. I can go back but can't get any further

    I just updated my original iPad 32 GB WiFi to iOS 5.1 about fifteen minutes ago.  But I did it with the system restore feature in iTunes.  So it wiped out everything on my iPad.  But it did work.  Then I restored an earlier backup and all went fine.  Maybe you could try backing up your iPad and then using Restore to get it back to factory settings to see what happens. 

  • MBP won't reboot past the white screen with the grey apple. Why? How do I fix it?

    MBP won't reboot past the white screen with the grey apple. Why? How can I fix it?

    Which OS are you on.
    try doing an SMC reset http://support.apple.com/kb/HT3964
    How long do you wait until giving up??

  • My ipad wont boot up past the apple icon

    my ipad wont boot up past the apple icon

    Frozen or unresponsive iPad
    Resolve these most common issues:
        •    Display remains black or blank
        •    Touch screen not responding
        •    Application unexpectedly closes or freezes
    http://www.apple.com/support/ipad/assistant/ipad/
    iPad Frozen? How to Force Quit an App, Reset or Restart Your iPad
    http://ipadacademy.com/2010/11/ipad-frozen-how-to-force-quit-an-app-reset-or-res tart-your-ipad
    What to Do When Your iPad Won't Turn On
    http://ipad.about.com/od/iPad_Troubleshooting/ss/What-To-Do-When-Your-Ipad-Wo-No t-Turn-On.htm
    iOS: Not responding or does not turn on
    http://support.apple.com/kb/TS3281
    iPad: Basic troubleshooting
    http://support.apple.com/kb/TS3274
     Cheers, Tom

  • My phone froze so i switched it off using the power button and home. now everytime it switches on, it wont go past the apple screen??

    my phone froze so i switched it off using the power button and home. now everytime it switches on, it wont go past the apple screen??

    Hello 3m4nz4,
    After reviewing your post, I have located an article that can help with your device. It contains a number of troubleshooting steps and helpful advice for the issue you are experiencing:
    iOS: Not responding or does not turn on - Apple Support
    Your iPhone, iPad, or iPod touch may occasionally stop responding to buttons, switches, or touchscreen input and may exhibit one or more of these symptoms:
    Does not return to the Home screen after you press the Home button
    Does not wake from sleep after you press the Sleep/Wake button
    Does not turn on (or power on) when you press any button
    Does not start up past Apple logo
    Appears frozen or unresponsive
    Is unable to "Slide to Unlock" or "Slide to Power Off"
    To troubleshoot these symptoms:
    If a single application is not responding or stops responding when it opens, you can force it to close.
    If the device is unresponsive or if certain controls aren't working as expected, restart your device.
    If the device remains unresponsive or does not turn on (or power on), reset your device.
    If there is no video or if the screen remains black, verify that the device has enough charge to turn on:
    If you are using an iPad, ensure that it's connected to the USB Power Adapter supplied with the device.
    Let it charge for at least twenty minutes, then see if it starts normally.
    If there is no image on the screen, press the Sleep/Wake button to attempt to wake the device.
    If the screen displays a red battery icon, continue charging the device until the battery is fully charged. Learn more about charging iPhone and iPod touch, or iPad.
    If the above steps do not resolve the issue, or the if the screen remains black or shows a persistent Apple logo, try restoring with iTunes:
    Connect the device to your computer and open iTunes.
    If the device appears in iTunes, select and click Restore on the Summary pane. Learn more about restoring iOS software.
    If the device doesn't appear in iTunes, try to force the device into recovery mode, and then restore it.
    If the above steps do not resolve the issue, contact Apple.
    Thank you for contributing to Apple Support Communities.
    Cheers,
    BobbyD

  • Hi guys. I've had my MacBook Pro for 2 years now. Last night it suddenly kept glitching to a dark grey screen every now and then, then it would flash yellow / blue spots, and now it won't go past the grey screen even when I reboot it.  I don't think I can

    Hi guys.
    I've had my MacBook Pro for 2 years now. Last night it suddenly kept glitching to a dark grey screen every now and then, then it would flash yellow / blue spots, and now it won't go past the grey screen even when I reboot it.
    I don't think I can access my disk anymore as I've moved across countries since I've first gotten my laptop.  it was working perfectly fine before  it kept going to the dark grey screen with a little blue on the bottom.
    If it helps, my camera light is still on, and it seems that my computer is working properly itself, but won't go past this grey screen.
    I'm a college student and am really panicking about this - can anyone please tell me what to do?
    Thank you & sorry for the long post.

    What operating system are you running on it? (iOS 5.1 is for iPhone, iPad...not a Mac).

  • Photos update won't open past the "preparing library" page

    iPhoto just updated to Photo 2015.  I can't get to my pictures because the app won't open past the "preparing library" page.
    The iPhoto update, under Apps, won't let me resume the update - I get an error "this item is temporarily unavailable".
    Any ideas?

    Hi wolfey_j
    Welcome to apple discussions.
    Drag and drop the plist for iDvd to the trash followed by a full restart of your mac and then repair permissions from apple's disc utility (application > utilities > disc utility)
    The plist for iDvd looks like this:
    com.apple.iDvd.plist
    If that fails to resolve this issue then delete iDvd using this free download from apple's web site:
    http://www.apple.com/downloads/macosx/systemdiskutilities/appdelete.html
    You'll need to re-install iDvd again (custom install from the software that shipped with your mac or any retail copy of iLife'09). And lastly run apple's software updater from system preferences so all is up to date again. (not a bad idea to repair permissions one more time after updating all apps.)
    Hope this resolves the issue/s but if not just come on back.
    Good luck.

  • IMac makes a loud beep on start up, won't load past the blue screen and the black ticking dial appears every few seconds in centre of screen.

    Urgent help!
    Out of the blue my mac lost the mouse cursor even though it had connection so I rebooted only for the mac to make a loud beep on start up then get stuck at the blue loading screen. It won't load past the blue screen. I've tried to reboot holding down the shift key but no change. I've also shut down, unplugged the main for 15 seconds, re plug and wait 5 seconds before starting up again but no change. Does anyone have any suggestions?
    PS: I'm not too sure which systems I am running without being able to check in about this mac. I bought my imac in January or February 2011 if that helps.

    The power on self-test resides in the ROM of the computer. This test runs whenever the computer is turned on after being fully shut down (the power-on self-test does not run if the computer is only restarted).
    If a fault is detected during the test, you will not hear a normal startup chime. Instead, the system will beep as explained below. If you experience one of these beeps, you may call your Apple Authorized Service Provider for additional troubleshooting assistance.
    1 beep = no RAM installed
    2 beeps = incompatible RAM types
    3 beeps = no good banks
    4 beeps = no good boot images in the boot ROM (and/or bad sys config block)
    5 beeps = processor is not usable
    http://support.apple.com/kb/HT1547

Maybe you are looking for