IPAD2 IS DEAD AFTER UPGRADED IOS8 - VERY SLOW

ios8 for ipad2 = dead ipad2 (slow and freeze)
thank Apple for you big bug !!!
now, i can't use my ipad2 ... why you block the possibility to downgrade to ios7 for ipad2 when you can't resolve problem ios8 for ipad2 ?
if i must change my ipad ... i change too all my family iphone and ipad ... and now i buy all with android system !!!!

Try some basic troubleshooting:
(A) Try reset iPad
Hold down the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears
(B) Try reset all settings
Settings>General>Reset>Reset All Settings
(C) Setup as new (data will be lost if you do not have backup)
Settings>General>Reset>Erase all content and settings

Similar Messages

After upgrade to iOS8, very slow, no volume slider bar, no volume through the iPad although the headphones work. My volume slider bar now reads"Sound Effects"?? Mute is off, need help. So frustrated!

I need help! After upgrading to iOS8.1.2 , my volume slider bar disappeared and is now "Sound Effects" ??? I have no external sound. Do have sound through headphones. Mute is off. Have tried resetting several times with no luck. Frustration level is building as I have wasted hours now on this. Any help would be greatly appreciated!

I do not think apple will do much to help you under warrenty, as this was caused by a fall. (alas!)
I think the case is, as you suggest, jamming the rocker down, and it may have damaged the swith itself. Can you carefully lever it out of the way? Very very carefully. If it is already broken, there is not much harm you can do by trying.
If it is just the switch being jammed, you might be able to move it out a little. If it is the swith itself, you will need some real service after your three hour drive. You might check your loacl area for a closer service repair source.

Mavericks install incomplete. No Apple installers on HD. Will I be able to upgrade to Yosemite and will it fix all that didn't install with Mavericks upgrade? Very slow connection speeds 30 hrs to download Mavericks. Tried re-install; no help/

Ever since upgrade to Mavericks I have been having problems which are too numerous to mention. I finally found a program from a UCBerkley professor called Pacifier which indicated 4000+ of 400,000+ files and folders did not install. I was unable to go further to try to fix everything because Pacifier can't find ANY Apple installers on my HD. It recommended I download the Mavericks installer without reinstalling to continue; however, after having done so (very slow connection; takes 30 hours to download) and although the installer appears in apps while downloading it disappears and NO Apple installer packages can be found on my hard drive. I tried to download Yosemite once and it indicated my system wasn't eligible for the upgrade. Its' download time was similar to Mavericks; 28+ hours.
I am using a Macbook Pro mid-2012 version OS X 10.9.5 (13F34); Processor 2.5 GHz Intel Core i5; Memory 4 GB 1600 MHz DDR3; Graphics Intel HD Graphics 4000 1024 MB.
Regardless of how many files and apps I remove my memory is being eaten up to the point I can hardly do anything at all. There are no civil words for how frustrated I am. Someone please help me.
Thanks,
JJ

Install Mavericks, Lion/Mountain Lion Using Internet Recovery
Be sure you backup your files to an external drive or second internal drive because the following procedure will remove everything from the hard drive.
Boot to the Internet Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND-OPTION- R keys until a globe appears on the screen. Wait patiently - 15-20 minutes - until the Recovery main menu appears.
Partition and Format the hard drive:
Select Disk Utility from the main menu and click on the Continue button.
After DU loads select your newly installed hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Click on the Partition tab in the DU main window.
Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Click on the Options button, set the partition scheme to GUID then click on the OK button. Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the process has completed. Quit DU and return to the main menu.
Reinstall Lion/Mountain Lion. Mavericks: Select Reinstall Lion/Mountain Lion, Mavericks and click on the Install button. Be sure to select the correct drive to use if you have more than one.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.
This should restore the version of OS X originally pre-installed on the computer.

After Effects CS6 - Very slow workflow

Hi everyone, my first writing in adobe forums. I've contacted 3 adobe support agents, but I didn't get much help from them. Recently I switched from PC to Mac Pro, having Adobe Production Premium 5.5 for Windows and now upgraded to Adobe Production Premium 6.
First I tried a trial of After Effects CC and I was surprised how slow it is. Now I'm using AE CS6 full version and it's a bit better, but still pretty dang slow. (The video I made for adobe support explaining the problem is here: http://www.youtube.com/watch?v=-jsZZpH0vYU )
To try to cut long story short. In the video adove, I've created couple of text layers and couple of shape layers. Made them 3D. Added a camera too. When I move the camera, everything is refreshing extremly slow. It's like you're having 100 3D layers and very busy scene,
and actually it's few most simplest 3D layers. The agents from adobe support told me to switch to half rez, or draft mode etc. But the problem is, I do not want to work in half rey, draft mode or something similar, with my configuration it should work pretty normal. Never
had these kind of problems in AE CS5.5. I tried everything, updated the software, updated my Mac OS, disabled global cache, even disabled multiprocessing etc. Btw, rendering is okay.
Is this the way CS6 is made? Is it supposed to be slow? Because, literally I got an answer from the agent that AECS6 is designed like that, in other words, to be slow
I really have no idea anymore how to make this work. I would like to get back to my lovely 5.5, but I only have license for Windows. If you guys could help me, I would really appriciate that.
I use:
* Mac Pro
* 2 x 2,4 GHz 6-Core Intel Xeon
* 64 GB 1333 MHz DDR3
* ATI Radeon HD 5870 1024MB
* 2TB HDD
* 2 x Apple LED Cinema Display 27"
* After Effects CS6 - 11.0.2.11
* Mac OS X 10.8.4
* I haven't had this problems ever before (using ae for quite some time)
* At the moment no 3rd party plugins installed
Thanks!
Mirza

You'll have to get used to creating Ram Previews and using AE's interface in the right way. You should really go through the getting started materials on the home page and take a look at the FAQ. AE is a layer based pixel calculating beast that will do a lot more to a movie at 60 frames per second than Photoshop will do on to a still image. After Effects is essentially Photoshop for movies with a lot more options.
If you want to smoothly drag through the timeline and playback multiple cuts with simple transitions and two or three layers then use Premiere Pro. If you need to use 20 layers and 60 effects to create a stunning composite or motion graphics effect then you're stuck with rendering at just about any price point.

E71 just went dead after upgrading

Well, I´ve stopped crying ´cause it did´nt help...
I plugged in my phone to the computer via USB and clicked on upgrade. It started and I left for a coffee. Came back and my phone was dead and the computer said it was a old version of OVI (changed it yesterday, so it wasn't that old) and that I ought to upgrade it and try again.
Yeah, well, I can´t start it now, it makes a buzz and then nothing more and it goes totally black again.
YES, I´ve tryed to press 3 * answerbutton and the on/off button simultaniously without any luck. Sometimes it starts (with the screen turning greyish) but then nothing more and it shuts down totally again.
HELP!
I don´t know what I´m supposed to do tomorrow and for the next few weeks....

Hi, I suggest you remove the battery and the memory card. Insert just the battery after one minute and try to boot it. If it boots try with the memory card again. If it fails you will probably have to format the card.
If it does not turn on, try another hard reset without having the memory card installed. As you may know the phone memory will be wiped doing it, but there doesn't seem to be any other choices.
One thing though, your phone didn't run out of battery during the update? If you're not sure, try charging it for at least 15 mins - if it will charge of course.
If nothing works and you cannot get it back to life you will unfortunately have to visit a Nokia care point to get it fixed.
As you've already tried getting it back to life but not succeded I guess this thread by psychomania: /t5/Pool-of-Knowledge/Recovering-from-a-failed-firmware-update/td-p/398147 isn't too much help, but if you get it back to life it gives some really good advices to what to do trying to update it again. It also provides you with the links to find your nearest Nokia care point.
It's worth reading. And make sure you do the hard reset correct as you will have to depress the key combination, hold those buttons in, push the power button, keep holding those three first keys in and keep holding the down until you're past the Nokia Handshake logo screen.
Good luck!

Macbook Pro (2008) dead after upgrade to 10.7.3

After download of the update it restarted.... well tha machine tried to restart. All went black.
Apple technician says he can't get the "validation error code" from the machine in regards to "free" logic board repair (http://support.apple.com/kb/TS2377). I am somewhat disapointed on the fact that the machine dont start even though it is "on" and Apple cant get the "code" beacasue it is not working properly? Catch 22. No I am not eligable and I have to buy a new Mac due to the 10.7.3 NON working upgrade. Im actually very frustrated.
I cant believe that it is a coincidence that my hardware stopped working just at the same time I was upgrading the OS. I think that is a whitewash for not doing the repair.
What can I do to get this issue solved without buying a new mashine for lots of hard earned money?

This is extremely unlikely. However, it is possible for a bug in software to damage your computer.
I suspect two possibilities.
1) Somehow 10.7.3 has altered your firmware preventing the computer from starting.
2) The hardware has failed coincidentally with upgrading. ( More likely in my view.)
Our office has switched back to Snow Leopard for security reasons. But I do know others running 10.7.3 without difficulties.
Apple cant get the "code" beacasue it is not working properly? Catch 22.
If your computer simply had the graphics chip problem the “code” would be readable. The reason they are unable to get this code is because your Mac has a deeper (and more serious) problem.

6110 Dead after upgrade

Hi!
I did right now do an software upgrade on my 6110, everything looked okay, no errors or pequliar messages, but now the phone won't start up. When I push the "on"-button, the usual "bzm" sounds and the screen lights up, but then nothing happens, and after about 15 seconds the screen goes black again and the phone don't react when I push the "on"-button. Is there any way to fix this other sending it to the serviceshop?

you can take the phone to service centre and let them flash it as a dead phone ie forcefully writing the software after that it should work and also when it works check out the maps.lock of the maps should be open.
tongue is too confused on what to speak

I am been asked to enter a passcode when I try to start My ipad2, this happen after upgrading to Ios7, anyone knows how to fix this error, thanks

Hello, I will appreciated any help to solve the problem with my ipad2. On September 22th, I decided to upgrade my Ipad2 to IOS7. It went fine and I used right fater the upgrade, however, the next day the Ipad was asking for a passcode, I didn't have a passcode before the update and don't know how to unlock it now. Any help will be appreciated. Thanks

iOS: Device disabled after entering wrong passcode
http://support.apple.com/kb/ht1212
How can I unlock my iPad if I forgot the passcode?
http://tinyurl.com/7ndy8tb
How to Reset a Forgotten Password for an iOS Device
http://www.wikihow.com/Reset-a-Forgotten-Password-for-an-iOS-Device
Using iPhone/iPad Recovery Mode
http://ipod.about.com/od/iphonetroubleshooting/a/Iphone-Recovery-Mode.htm
Saw this solution on another post about an iPad in a school enviroment. Might work on your iPad so you won't lose everything.
~~~~~~~~~~~~~
‘iPad is disabled’ fix without resetting using iTunes
Today I met my match with an iPad that had a passcode entered too many times, resulting in it displaying the message ‘iPad is disabled – Connect to iTunes’. This was a student iPad and since they use Notability for most of their work there was a chance that her files were not all backed up to the cloud. I really wanted to just re-activate the iPad instead of totally resetting it back to our default image.
I reached out to my PLN on Twitter and had some help from a few people through retweets and a couple of clarification tweets. I love that so many are willing to help out so quickly. Through this I also learned that I look like Lt. Riker from Star Trek (thanks @FillineMachine).
Through some trial and error (and a little sheer luck), I was able to reactivate the iPad without loosing any data. Note, this will only work on the computer it last synced with. Here’s how:
1. Configurator is useless in reactivating a locked iPad. You will only be able to completely reformat the iPad using Configurator. If that’s ok with you, go for it – otherwise don’t waste your time trying to figure it out.
2. Open iTunes with the iPad disconnected.
3. Connect the iPad to the computer and wait for it to show up in the devices section in iTunes.
4. Click on the iPad name when it appears and you will be given the option to restore a backup or setup as a new iPad (since it is locked).
5. Click ‘Setup as new iPad’ and then click restore.
6. The iPad will start backing up before it does the full restore and sync. CANCEL THE BACKUP IMMEDIATELY. You do this by clicking the small x in the status window in iTunes.
7. When the backup cancels, it immediately starts syncing – cancel this as well using the same small x in the iTunes status window.
8. The first stage in the restore process unlocks the iPad, you are basically just cancelling out the restore process as soon as it reactivates the iPad.
If done correctly, you will experience no data loss and the result will be a reactivated iPad. I have now tried this with about 5 iPads that were locked identically by students and each time it worked like a charm.
~~~~~~~~~~~~~
Try it and good luck. You have nothing more to lose if it doesn't work for you.
 Cheers, Tom

MBP as good as dead after upgrade to 5.8?

Hi All,
A strange problem with my MBP after trying to upgrade to 5.8. It never restarted after a seemingly normal installation script. Only things happening are the sleeping led comming on, a short sounding noise from the fan, the cd-drive clicking and the sleeping led going off.
I tried every bit of troubleshooting I could find which gave me one little spark of hope: after holding down the power button for a second or ten the sleeping light shows a read-out: a two second burst of on-off's followed by a short pause followed by going on for one second.
Is there anyone out there who got a clue what the diagnosis of this might be?
I'm certain it will end up in my local Apple Store but knowing the guys over there it would be better if I try to be at least one step ahead...
Thanks in advance!!
grts, Michel

Update:
As feared, gone to a Apple Center, back to phone with Apple Care, forth to Apple Center again, Apple being slightly apathic to my complaints how a 1.5 year old computer bearing a logo that is supposed to show a high degree of quality and on to a Service Center where they suspect a failing logic board... all parties agree this is not what to expect from a machine with this price tag, noon action what so ever.
For now the MBP is on the test bench - i hope it's the graphic card.
I did get a replacement macbook for the time being. It's not all bad, just extreme improvising.
@ neuroanatomist: Dang!!! 9 years short of ANBO
grts,
Michel

Nokia E65 pretends to be dead after upgrade to fir...

I upgraded my Nokia E65 and the upgrade failed while Nokia was in "test mode" after about ten minutes of upgrade process. But the phone restarted and worked well in new firmware. I decided to give one more chance to be sure and the upgrade failed again, this time phone was in "Nokia local mode". And yet the phone works perfectly and the firmware is version 3.
What's wrong if any?

Hi,
please describe your problem shorter and clearly.
i dont understand can you upgrade your phone successfully or no?
NOKIA means:Night Of King In Alone

After Effects CC14 very slow

My After Effects CC 2014 is extremly slow and it is just crashing all the time.
This is my system. What can be the reason for it?
Would appreciate any tipps...

Well, you are running on an unsupported version of OSX....
System requirements | After Effects
Mylenium

E2500 dead after upgrade

hi,
i upgrated my E2500 with the last version of firmware but now is dead. the power led is turn on, but the ping are discontinued. the other problem is that after 10/15 sec, the router will restart automatically. i try with tftp but after the reset of router does not change anything.
there's a solution or i must trash my router?
thanks

gokuinsido wrote:
hi,
i upgrated my E2500 with the last version of firmware but now is dead. the power led is turn on, but the ping are discontinued. the other problem is that after 10/15 sec, the router will restart automatically. i try with tftp but after the reset of router does not change anything.
there's a solution or i must trash my router?
thanks
Hi,
Update should fix router issues or more features can be added . But how did you update the router ? Did you use a laptop that's connected wirelessly to the network ? or a wired computer ?
I believe that I can make it

SRW224G4 - cant manage with new firmware thru Xmodem (dead after upgrade)

Hi All,
Before i wrote this msg, i saw few threads aboud "problem with upgrade firmware". Today i've upgraded my Linksys SRW224G4 to newest 1.2.2b and... after rebot, switch was still rebooting. I found on cisco site how to solve the problem regarding this: http://www.cisco.com/en/US/products/ps9967/products_qanda_item09186a0080a36371.shtml
So, i've made RS232 (because i don't have orginal one ; pinout 1-1 2-2 3-3 4-4 5-5) and connected to console
The problem is with hiting ESC on POST screen. My hyperterminal freezes So, i can't upload my files
Files: SRW224G4_fesm-12216.ros ; ls_106-12216.ros ; SRW224G4-1.0.0.61
------ Performing the Power-On Self Test (POST) ------
UART Channel Loopback Test........................PASS
Testing the System SDRAM..........................PASS
Boot1 Checksum Test...............................PASS
Boot2 Checksum Test...............................PASS
Flash Image Validation Test.......................PASS
BOOT Software Version 1.0.0.06 Built 23-May-2005 16:58:25
Linksys SmartSwitch based on 88E6218 with ARM946E-S.
32MByte SDRAM. I-Cache 8 KB. D-Cache 8 KB. Cache Enabled.
Autoboot in 2 seconds - press RETURN or Esc. to abort and enter prom.
Preparing to decompress...
100%
FAIL !!! Check image for valid file.
Please download a new image.
Downloading code using XMODEM.
Download failed
Perform WARM BOOT ...
------ Performing the Power-On Self Test (POST) ------
UART Channel Loopback Test........................PASS
Testing the System SDRAM..........................PASS
Boot1 Checksum Test...............................PASS
Boot2 Checksum Test...............................PASS
Flash Image Validation Test.......................PASS
BOOT Software Version 1.0.0.06 Built 23-May-2005 16:58:25
Linksys SmartSwitch based on 88E6218 with ARM946E-S.
32MByte SDRAM. I-Cache 8 KB. D-Cache 8 KB. Cache Enabled.
Autoboot in 2 seconds - press RETURN or Esc. to abort and enter prom.
Preparing to decompress...
100%
FAIL !!! Check image for valid file.
Please download a new image.
Downloading code using XMODEM.
When i try to send SRW224G4_fesm-12216.ros now, HT freezes too
Guys, what shall i do now ?
I think the RS232 cable is ok, pinout is linke normal DB9 one-to-one without crossing 2 with 3 pin.
Best regards, w8ing 4 any help.

So...
I've solved it
Problem was with settings in HT and sending ESC chacter
thank U ;D

Infiniti Q50 bluetooth issues after upgrade ios8

I have been using my iPhone 5S with iOS 8 and have had quite a bit of Bluetooth connection issues on the phone. Not connecting via car but other party hears me on the iPhone and I can put it to my ear and hear them even though its BT connected. Random "hang ups" on the InTouch screen, but still connected on the phone. Calls dropped after answering the phone via BT/InTouch.

Having similar issues. Audio from iphone 5s works over bluetooth, but when making or receiving phone call music pauses and there is no phone audio.
BMW 335i 2012.
Seriously. Does anybody test this software?

After upgrade it became slow... :/

My Mac Pro was running fine until i upgraded to the free maverick in app store. Should i downgrade / what should i do to improve my Mac Pro performance?

When you have the problem, note the exact time: hour, minute, second.
These instructions must be carried out as an administrator. If you have only one user account, you are the administrator.
Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
The title of the Console window should be All Messages. If it isn't, select
SYSTEM LOG QUERIES ▹ All Messages
from the log list on the left. If you don't see that list, select
View ▹ Show Log List
from the menu bar at the top of the screen.
Each message in the log begins with the date and time when it was entered. Scroll back to the time you noted above. Select the messages entered from then until the end of the episode, or until they start to repeat, whichever comes first. Copy the messages to the Clipboard by pressing the key combination command-C. Paste into a reply to this message by pressing command-V.
☞ The log contains a vast amount of information, almost all of it useless for solving any particular problem. When posting a log extract, be selective. A few dozen lines are almost always more than enough.
Please don't indiscriminately dump thousands of lines from the log into this discussion.
Please don't post screenshots of log messages—post the text.
☞ Some private information, such as your name, may appear in the log. Anonymize before posting.

IPAD2 IS DEAD AFTER UPGRADED IOS8 - VERY SLOW

Similar Messages

Maybe you are looking for