IPad2 OS5 with Android 2.3 hotspot fails, but iPad2 OS4 with Android 2.3 hotspot works - why?.

Has the abilityy to link to a hotspot been disabled in OS5?
I get a message that the iPad2 (OS5.0.1) is paired with my Android (LG-P500) phone BUT is not connected. I can see the Android's WiFi name in the iPads list of possible networks and can connect to it with a password.
I also have an ipad-2 with OS4.3.3 which connects properly and gives no trouble.
Any work around is welcome - I suppose I could doowngrade again.

Downgrade is not a solution. If your pad cannot connect to the Internet via the hotspot, then it has not successfully grabbed the hotspot. Keep trying. The pass word or some other issue is causing the problem.

Similar Messages

Using iMovie 7.1.4 on an iMac w/ Snow Leopard; HD video imported with a Firewire cable transfers fine, but audio arrives with major static; problem persists w/ different cameras

Using iMovie 7.1.4 on an iMac w/ Snow Leopard; HD video imported with a Firewire cable transfers fine, but audio arrives with major static; problem persists w/ different cameras & Firewire cables; source DV tape has no audfio static.

I forgot to write down my computer specs:
iMac 27 Mid 2011
2.7 GHz Intel Core i5
4 GB 1333 MHz DDR3
AMD Radeon HD 6770M 512 MB
OS X 10.9.2

I have an hd movie on both my ipad and iPhone 5, using airplay with my iPhone 5 plays perfectly but gets stuck with my ipad 2, almost like its buffering? I just want it to play smoothly like with my iPhone. Any suggestion?

I have an hd movie on both my ipad and iPhone 5, using airplay on my apple tv with my iPhone 5 plays perfectly but gets stuck with my ipad 2, almost like its buffering? I just want it to play smoothly like with my iPhone. Any suggestion?

About 6 months ago I discovered iTunes was set by default to 720p. These MUST BE CHANGED TO 1080P!!!!!!!!.......So I installed FULL 1080P file on my laptop on iTunes... When I download movies on iPhone 5s/iPad mini the file is 720p So within about 60 seconds of starting download of 1080p files into my laptop of iTunes purchases. It was at that moment that I realized it was that file my laptop has on file to sync to my Apple device...Ten minutes later when the first 1080P HD file was downloaded I must say... The resolution is amazing... I now use this same process to install movie files from iTunes.. In FULL 1080P.. Not 720P... Works on my iPad mini also... Avatar is 5.4 GB if installed over Wi-Fi... However sync with laptop and file is 6.5 GB in size... Called Apple told them... No reply yet.... You must delete 720P files from your laptop... Look for file size in any movie purchase and you will see DOWNLOAD IN 1080P.. This will open preferences in iTunes for you to the correct tab so you can change setting to 1080p from default of 720p... DELETE any downloaded movies already downloaded into laptop... You can check file quality by right click on any movie folder and the look at movie info... Will say 720p HD... Delete to recycle bin and iCloud will appear on each movie... Now download 1080P HD file... When completed. Right click any file to verify it is 1080P HD... The sync with device...... And get ready to be upset with Apple for holding back your device for the last 2 years 3 months and 16 days......And be ready to catch your jaw from hitting the floor when you see your screen in full 1080P HD.... Apple Engineer's were asleep.....
You will notice better pic quality... Apple by default is still sending the 720P file to the new iPhone 6 plus over wifi and sync.. howve this process above will give you full HD file for your Apple device...

I can not update or restore any ios device with my iTunes in my macbook but I can with my pc, why?

I can not update or restore any ios device with my iTunes in my macbook but I can with my pc, why?

Hi, I have updated my MacPro, Iphone and Ipad and installed the Icloud. My Ipod merges with the Ipad and visa versa but neither merges with the notebook nor does the notebook merge with them.

I have updated my MacBook Pro, my Iphone 4 and my Ipad2. My Iphone merges with the Ipad via ICloud and visa versa, but neither merge with the notebook nor does the notebook merge with them. there are no further updates on my notebook to download, any suggestions?
Maureen

Home Sharing is designed to work on your local network not across the internet/cloud.
Stuff is accessed under the Computers column where your local iTunes library on a local computer would appear.
Home Sharing would share your iTunes content (i.e. stuff stored in itunes on the computer, not in the cloud) with AppleTV or an iPad etc on the SAME network.
AppleTV2 will not be able to see itunes content on the work computer over the internet. It's not designed to. if the work computer was on the home network it would.
iCloud is in it's infancy and is not a mature product - iTunes TV Show purchases appear on AppleTV, but currently music does not unless you are subscribed to iTunes Match. I find this rather odd to be honest, along with the inability to buy music on AppleTV2. Movies purchased in iTunes are not authorised for iCloud viewing currently either.
Maybe it has something to do with iTunes Match 'getting in the way' - i think they assume you'll use that whereas you really want to be able to access Purchased music from the cloud without subscribing to itunes Match which is overkill for some.
AC

Download failed, but iPad2 keeps dowload again and again

My iPad2 is still with its original operation system. I have not upgrade to any new OP.
Recently, I tried to update the applications (I was informed), each time, I got download update failed. Then, a pop out window for me to choose "done", or "retry". Since "retry" does not help (still failed), so I clicked "done". But, the system keeps reload the update by itself, I have no way to stop it.
I tried to totally turn of iPad itself. After more 10 10 minutes, then restart iPad. But, the update is still reload itself. Never ending.
One of the application is free, so I totally removed the application to stop the redicules "loading"/"failed". But, the other is the application I bought. I don't want to delete it, but, have no way to stop the reload/falied cycle.
First I like to know:
- Why suddently the updates failed each time (at least 2 weeks now)?
- How to stop the reload/failed cycle?
Thank you very much.
Jenny

Have you paid for the pre-order - you are only charged for pre-orders when they become available and you download them, you aren't charged at the time of pre-ordering them. Does it show on your account's purchase history : if you log into your account on your computer's iTunes via the Store > View Account menu option, you should then see a Purchase History section with a 'see all' link to the right of it, click on that and you should then see a list of your purchases (the most recent purchase is above the list).
If you haven't yet paid then you will need a balance or a credit card on your account so that you can pay for it before you will be able to download it.
If you have paid for it then does the Store > Check For Available Downloads menu option on your computer's iTunes find and download it, and/or does it show in the Purchased link in the iTunes store app on your phone and the Purchased link under Quicklinks on the right-hand side of the iTunes store homepage on your computer's iTunes ?

Move of mailbox with over 30K of folders fails, how to deal with this.

Hello all,
I'm in the process of moving all Exchange 2010 mailboxes to newly created databases located on new storage.
Every mailbox except one moved successfully, the "problem" mailbox keeps failing and I need some advise on how to deal with this.
The mailbox that keeps failing is only 4 GB but has over 30K of folders that the users created manually over the years.
They are unable to easelly delete folders as they have created many sub folders within the folders.
I posted a part of the failed move request log below.
Can anyone advise on how to solve this?
Thanks in advance.
21-2-2015 18:15:13 [EXHUB1] Fatal error MapiExceptionMaxSubmissionExceeded has occurred.
Error details: MapiExceptionMaxSubmissionExceeded: Unable to save changes. (hr=0x80004005, ec=1242)
Diagnostic context:
Lid: 55847 EMSMDBPOOL.EcPoolSessionDoRpc called [length=7574]
Lid: 43559 EMSMDBPOOL.EcPoolSessionDoRpc returned [ec=0x0][length=360][latency=0]
Lid: 23226 --- ROP Parse Start ---
Lid: 27962 ROP: ropWriteStream [45]
Lid: 27962 ROP: ropSetProps [10]
Lid: 27962 ROP: ropSaveChangesMessage [12]
Lid: 17082 ROP Error: 0x4DA
Lid: 18273
Lid: 21921 StoreEc: 0x4DA
Lid: 27962 ROP: ropExtendedError [250]
Lid: 1494 ---- Remote Context Beg ----
Lid: 26426 ROP: ropSaveChangesMessage [12]
Lid: 27420 dwParam: 0xE1F000B
Lid: 36537 dwParam: 0xE1F000B
Lid: 5587 StoreEc: 0x8004010F PropTag: 0xE1F000B
Lid: 33375 StoreEc: 0x8004010F
Lid: 27420 dwParam: 0x806684B0
Lid: 36537 dwParam: 0x806684B0
Lid: 5587 StoreEc: 0x8004010F PropTag: 0x806684B0
Lid: 64931 StoreEc: 0x8004010F
Lid: 46509
Lid: 40193 StoreEc: 0x8004010F
Lid: 5587 StoreEc: 0x8004010F PropTag: 0x30130102
Lid: 21970 StoreEc: 0x8004010F PropTag: 0x668F0040
Lid: 64319 dwParam: 0x5000
Lid: 39743 dwParam: 0x6730
Lid: 45016 StoreEc: 0x4DA
Lid: 57304
Lid: 5041 StoreEc: 0x4DA
Lid: 4465 StoreEc: 0x4DA
Lid: 6926 StoreEc: 0x4DA
Lid: 1750 ---- Remote Context End ----
Lid: 31418 --- ROP Parse Done ---
Lid: 21457
Lid: 19665 StoreEc: 0x4DA
at Microsoft.Mapi.MapiExceptionHelper.ThrowIfError(String message, Int32 hresult, SafeExInterfaceHandle iUnknown, Exception innerException)
at Microsoft.Mapi.MapiProp.SaveChanges(SaveChangesFlags flags)
at Microsoft.Exchange.MailboxReplicationService.MoveObjectInfo`1.CreateMessage(T obj, GetAdditionalProperties getAdditionalPropertiesCallback)
at Microsoft.Exchange.MailboxReplicationService.MoveObjectInfo`1.CreateMessage(T obj)
at Microsoft.Exchange.MailboxReplicationService.LocalMailbox.Microsoft.Exchange.MailboxReplicationService.IMailbox.SaveSyncState(Byte[] key, String syncStateStr)
at Microsoft.Exchange.MailboxReplicationService.MailboxWrapper.<>c__DisplayClass57.<Microsoft.Exchange.MailboxReplicationService.IMailbox.SaveSyncState>b__56()
at Microsoft.Exchange.MailboxReplicationService.ExecutionContext.Execute(GenericCallDelegate operation)
at Microsoft.Exchange.MailboxReplicationService.MailboxWrapper.Microsoft.Exchange.MailboxReplicationService.IMailbox.SaveSyncState(Byte[] key, String syncState)
at Microsoft.Exchange.MailboxReplicationService.MailboxCopierBase.SaveSyncState(SaveStateFlags flags)
at Microsoft.Exchange.MailboxReplicationService.BaseJob.SaveSyncState(SaveStateFlags flags)
at Microsoft.Exchange.MailboxReplicationService.BaseJob.SaveState(SaveStateFlags flags, UpdateRequestDelegate updateRequestDel)
at Microsoft.Exchange.MailboxReplicationService.MoveBaseJob.SortMessages(Object[] wiParams)
at Microsoft.Exchange.MailboxReplicationService.CommonUtils.CatchKnownExceptions(GenericCallDelegate del, FailureDelegate failureDelegate)
Error context: --------
Operation: IMailbox.SaveSyncState
OperationSide: Target
Primary (a4966c13-778a-4d70-9087-f077e2523f66)
Key: FEF1D04E070AB74A99B809B7797674AE000000000000000000000000000000009B5540B45B37774CAB84806C1964B598
SyncStateLength: 27050362
21-2-2015 18:15:13 [EXHUB1] Relinquishing job.

Hi,
Based on the description, please run the following commands to check if there are any message limit size. Try to increase the limit size then move this mailbox.
Get-mailbox –identity “user name” | fl MaxSendSize,MaxReceiveSize
Get-transportconfig | fl MaxSendSize,MaxReceiveSize
Get-transportrule | fl MessageSizeOver
Get-sendconnector | fl MaxMessageSize
Get-receiveconnector | fl MaxMessageSize
Note: Once we increased the value we need to wait for the AD replication and cache to be cleared and then test the move mailbox.
If this doesn’t work, please try to move mailbox with the skip corrupted items. This will skip the corrupted items and move only the good items to the target mailbox.
Similar thread:
https://social.technet.microsoft.com/Forums/en-US/5383a826-4383-4b26-a503-2c3bb635f9d2/mailbox-move-to-exchange-2010-fails-for-mailboxes-over-23-gb?forum=exchangesvrdeploylegacy
Best Regards.

Ipad 3 with ios6 can not find airplay mirror to Apple TV 3 , but my another ipad2 with ios7 can do it. But ipad 3 with ios6 can airplay mirror to my friend's apple tv

I have two iPads . One is ipad 3 with ios 6, can not find airplay-Mirror to Apple TV 3 . But it can do it at my friend' s Apple TV.
My another ipad 2 with ios7 can airplay -mirror at my Apple TV 3 .
My ipad 3 64GB already full, so I don't delegate something to upgrade to ios7 .
I am wondering why it can do it at my friend's Apple TV, not mine

Try the following steps, check whether things are working after each step where appropriate, before trying the next.
Check AirPlay is turned on on the Apple TV (turn it off and on if it already is)
Check that both devices are on the same network (Settings > Wifi, on the mobile device and Settings > General > Network, on the Apple TV).
Restart the Apple TV (Settings > General > Restart).
Restart the Apple TV by removing ALL the cables for 30 seconds.
Restart your router. (Also try removing it’s power cord for at least 30 seconds)
Restart your mobile device.

Is it Possible to Promote DC on a Subnet With Connectivity to a Site DC But Not DC with FSMO Roles???

I apologize in advance for the rambling novella, but I tried to include as many details ahead of time as I could.
I guess like most issues, this one's been evolving for a while, it started out with us trying to add a new member
to a replication group that's on a subnet without connectivity to the FSMO roles holder. I'll try to describe the
layout as best as I can up front.
The AD only has one domain & both the forest & domain are at 2008R2 function level. We've got two sites defined in
Sites & Services, Site A is an off-site datacenter with one associated subnet & Site B with 6 associated subnets, A-F.
The two sites are connected by a WAN link from a cable provider. Subnets E & F at Site B have no connectivity to Site A
across that WAN, only what's available through the front side of the datacenter through the public Internet. The network
engineering group involved refuses to route that WAN traffic to those two subnets & we've got no recourse against that
decision; so I'm trying to find a way to accomplish this without that if possible.
The FSMO roles holder is located at Site A. I know that I can define a Site C, add Subnets E & F to that site, & then
configure an SMTP site link between Sites A & C, but that only handles AD replication, correct? That still wouldn't allow me, for example,
to enumerate DFS namespaces from subnets E & F, or to add a fileserver on either of those subnets as a member to an existing
DFS replication group, right? Also, root scalability is enabled on all the namespace shares.
Is there a way to accomplish both of these things without transferring the FSMO roles from the original DC at Site A to, say,
the bridgehead DC at Site B?
When the infrastructure was originally setup by a former analyst, the topology was much more simple & everything was left
under the Default First Site & no sites/subnets were setup until fairly recently to resolve authentication issues on
Subnets E & F... I bring this up just to say, the FSMO roles holder has held them throughout the build out & addition of
all sorts of systems & I'm honestly not sure what, if anything, the transfer of those roles will break.
I definitely don't claim to be an expert in any of this, I'll be the first to say that I'm a work-in-progress on this AD design stuff,
I'm all for R'ing the FM, but frankly I'm dragging bottom at this point in finding the right FM. I've been digging around
on Google, forums, & TechNet for the past week or so as this has evolved, but no resolution yet.
On VMs & machines on subnets E & F when I go to DFS Management -> Namespace -> Add Namespaces to Display..., none show up
automatically & when I click Show Namespaces, after a few seconds I get "The namespaces on DOMAIN cannot be enumerated. The
specified domain either does not exist or could not be contacted". If I run a dfsutil /pktinfo, nothing shows except \sysvol
but I can access the domain-based DFS shares through Windows Explorer with the UNC path \\DOMAIN-FQDN\Share-Name then when
I run a dfsutil /pktinfo it shows all the shares that I've accessed so far.
So either I'm doing something wrong, or, for some random large, multinational company, every sunbet & fileserver one wants
to add to a DFS Namespace has to be able to contact the FSMO roles holder? Or, are those ADs broken down with a child domain
for each Site & a FSMO roles holder for that child domain is located in each site?

Hi Matthew,
Unfortunately a lot of the intricacies of DFS leave my head as soon as I’m done with a particular design or troubleshooting situation but from memory, having direct connectivity to the PDC emulator for a particular domain is the key to managing domain based
DFS.
Have a read of this article for the differences between “Optimize for consistency” vs “Optimize for scalability”:
http://technet.microsoft.com/en-us/library/cc737400(v=ws.10).aspx
In brief, I’d say they mean:
In consistency mode the namespace servers always poll the PDCe for the latest and greatest information on the namespaces they are hosting.
In scalability mode the namespace servers should poll the closest DC for information on the namespaces they are hosting.
The key piece of information in that article about scalability mode is: “Updates are still made to the namespace object in Active Directory on the PDC emulator, but namespace servers do not discover those changes until the updated namespace object replicates
(using Active Directory replication) to the closest domain controller for each namespace server.”
I read that as saying you can have a server running DFS-N as long as it has connectivity to a DC but if you want to make changes, do them from a box that has direct connectivity to the PDCe. Then let AD replication float those changes out to your other DCs
where the remote DFS-N server will eventually pick them up. Give it a try and see how you get on.
That being said, you may want to double check that you have configured the most appropriate FSMO role placement in your environment's AD design:
http://technet.microsoft.com/en-us/library/cc754889(v=ws.10).aspx
And a DFS response probably wouldn’t be complete without an AskDS link:
http://blogs.technet.com/b/askds/archive/2012/07/24/common-dfsn-configuration-mistakes-and-oversights.aspx
These links may also help:
http://blogs.technet.com/b/filecab/archive/2012/08/26/dfs-namespace-scalability-considerations.aspx
http://blogs.technet.com/b/josebda/archive/2009/12/30/windows-server-dfs-namespaces-reference.aspx
http://blogs.technet.com/b/josebda/archive/2009/06/26/how-many-dfs-n-namespaces-servers-do-you-need.aspx
I hope this helps,
Mark

Worked with PP,MM,SD,QM, PS, but no experience with FICO, GL

Hi,
I worked with PP,MM,SD,QM, PS modules. But I didn't work with FICO, GL, AR, AP. Are these similar to SD/MM modules or any special configurations required while designing Cubes and ODS's?
Thanks,
Ranjani

For FI and CO extractors, no special steps. Nothing like Lo extractors.
Two exceptions to this; for COPA and Special ledger, there wont be any business content extractors; you need to define your own.
Ravi Thothadri

On my I pad mini I keep getting "cannot get mail" the connection to the server failed. but everything is Ok I can get mail. Why do I get this message??

On my I pad Mini I keep getting the message "Cannot get Mail" The connection to the server has failed.
But this is not the case everything works OK so why do I get the message

An iOS fluke or mail app glitch maybe. Not sure anyone will know why you get it. Do you're ever close the mail app? Try closing it and reset the iPad and see if the message goes away.
Assuming that you are running iOS 7, in order to close apps, you drag the app up from the multitasking display. Double tap the home button and you will see apps lined up going left to right across the screen. Swipe to get to the Mail app that you want to close and then swipe "up" on the app preview thumbnail to close it.
Reset the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider if it appears on the screen - let go of the buttons. Let the iPad start up.

Windows xp old desktop, downloaded firefox, able to search web with google in top righthand corner, but can't search using the firefox search box, why not?

Computer novice, with old windows xp desktop, changed to firefox, have firefox as homepage, but can't use the central firefox search box, I type a word, click on search .......and....wait.......nothing happens. Have been able to use the top right hand corner search box (set on google). Not great with computers, so feel like I'm really missing something basic! Help! Thanks!

hello, please see if installing the search reset addon can resolve the issue: https://addons.mozilla.org/firefox/addon/searchreset/ (a restart of the browser is necessary afterwards).

Mac-Pro (Lion) with QuickTime X has normal audio but black screen with WMV files. Re-installed Flip4Mac and installed Perian without success.

duplicate message

Hi Exceldpstudiocc5,
can you please elaborate, which creative cloud app you are using and what kind of file you are trying to open?
I' m assuming, it could be an issue with fonts or type of files.
Regards,
Ashish

I have Firefox 5.0.1, and a theme I want to download says that it works with Firefox 4.0b9pre - 7.0a1, but at the top it says that it is not available for my platform. What do I do?

I just downloaded Firefox 5.0.1, and one of the themes I want to download and try out says that it works with Firefox 4.0b9pre - 7.0a1. At the top, though, it says that the theme is not available for my platform. It has happened with some other themes as well, but I didn't check what versions they work with. I don't know what this means or what to do about it. The theme is at this link: https://addons.mozilla.org/z/en-US/firefox/addon/bloomind-ft-deepdark-2/

It says:
<blockquote>"Bloomind FT DeepDark 2" is a theme that has been created to transform the look of Firefox 4 for Windows users. It has been specially designed for Seven, but rendering is relatively accurate on XP and Linux (I can t test it on MAC, but for those who would like to try it anyway on that platform, you can force download and install it).</blockquote>
So try to save that file via the right-click context menu.
*http://kb.mozillazine.org/Themes

PC Used to work with XP and airport Extreme Basestation but not with Vista

Please help, my PC Used to work with XP and airport Extreme Basestation but not now with Vista. I have a MacBook Pro connected and also a Mac Pro connected to the network on it and they still work, i have put the latest software on the PC and the firmware is up to date. The only thing i can see on the network on the PC is the basestation Hard Disk (shared also to the Macs) but i cannot connect with the password, i have tried everything in my knowledge, including formatting the machine and reinsatlling OS and changing security setting to no avail. Any ideas anyone?

With regard to your printer problem - take a look at this discussion:
http://discussions.apple.com/thread.jspa?messageID=6312413&tstart=0

IPad2 OS5 with Android 2.3 hotspot fails, but iPad2 OS4 with Android 2.3 hotspot works - why?.

Similar Messages

Maybe you are looking for