Ipad2 reboots every 1 or 2 minutes

My ipad2 started rebooting every 1-2 minutes. I took it to a service centre where i was told its a small software issue and then i was told its a hardware issue and asked to pay 21000 ( 400$) for a replacement. Ipad2 was just 97 days old ?

Charge Information:
  Charge Remaining (mAh):          337
  Fully Charged:          No
  Charging:          Yes
  Full Charge Capacity (mAh):          4848
Health Information:
  Cycle Count:          371
  Condition:          Normal
It says Firefox is using a lot of CPU, but when I try to delete Firefox because I don't need it, it says it's in use when I've quit out of it. What should I do now?

Similar Messages

  • IPad2 reboots every few minutes

    My iPad2 recently began to reboot every few minutes of use.  It has been reformatted, all added apps removed and the battery allowed to completely deplete then recharge, all to no avail.  Any suggestions?

    If you are near an Apple Store, a trip to the Genius Bar.  If you are still under warranty they can replace it.  If you are out of warranty, they may still be able to replace it for a fee but it will still be less than full retail cost.

  • I have iphone 4s  downloaded  ios7  the phone now reboots every 3 or 3 minutes what is wrong

    Can anyone help  have iphone 4s m4m 64 downlosded ios 7 now phone shuts down every 2 to 3 minutes and re boots make phoe unusable and unable to send messages or make call because of shut down
    I have tried a cold restart no help  holding home button during power up

    you may have to perform a full restore via itunes. Be warned, that process will remove all of you data from the device, so make sure to have a back up somewhere

  • WRT54G reboots every 20 minutes

    I recently just switched from astound to comcast and astound worked fine 100% uptime no d/cs or anything...When we switched to comcast the router reboots every 20 minutes. I called comcast and they said everything is fine on their end. I tried power cycling everything and still no luck. When i connect directly to the modem I get no d/cs. Anyone have any ideas? Thanks in advance for any possible help, and sorry for my prolly horrible grammar. =]
    Message Edited by Hukepi on 08-08-2007 10:31 PM

    hi... connect the computer directly to the modem, go to www.linksys.com/download and download the latest firmware for the router, connect modem >> router >> pc, logon to router's setup page, open I.E. and in the address bar type 192.168.1.1 it would ask for username and password...put "admin" (default password) as a password and try reflashing/upgrading firmware on the router, after reflashing firmware on the router reset it and reconfigure it according to ISP settings and try reducing MTU to 1365 on the router...check whether it makes any difference or not and let me know the results.

  • IPad constantly reboots every 2-3 minutes, after full recovery is not activated to  wi-fi, and Itunes - for 20 days, Itunes says that the activation was not possible because the server is not available try again later. Ipad under warranty, but he was more

    IPad constantly reboots every 2-3 minutes, after full recovery is not activated to  wi-fi, and Itunes - for 20 days, Itunes says that the activation was not possible because the server is not available try again later. Ipad under warranty, but he was more than 6 months, so please call customer service apple can not. by DFU also restored Official Ipad bought in a store in Russia. When buying activated immediately.  IMEI 013311005943507. Help please! the official service Moscow  representation FDA ipad offer to send in the U.S. for $ 500!

    Hello this is happening to us also (minus the Bluetooth speaker).  We can't figure out what is causing the data usage.  I turned off mobile data as soon s I activated the device, and got the message that unless I am connected to WiFi.....(that is exactly what I wanted). We watched Netflix for about three hours, then the alerts started.  Like you we have many devices connected and never used over 2GB now all of a sudden we have used it in a matter of hours.  My husband called Verizon  and got the usual doubting Thomas response.  I understand that they don't know my device settings.  So over the phone we check all the settings and turned  off every possible culprit eating up the data and end the call.  By now I have purchased another gig for the month!  Assured we are NOT using mobile data, we continue on the IE path to bliss.  HA!  A few hours later I check the mobile data usage on the Verizon website and that darn thing is still using data.  After two more phone calls and two VERY uneventful trips to the local store we were told to take out the sim card.  This has stopped the data usage, but it defeats the purpose of having the data plan.  I could have just stuck with my Surface.  Verizon sent us a new sim card.  Its been installed and I have set my homepage to Verizon mobile data usage (just kidding) but I am on that site a lot.   I am surprised at the number of complaints about this device.  When we called the Verizon support acted as though this was the first time they had heard about this.   Loved your post, you should write for a living.

  • My iphone4s keeps rebooting every 3 minutes; what might be wrong

    My iphone 4s keeps rebooting every 3 minutes; what might be wrong

    Welcome to the Apple Community.
    Check that the HDMI cable is seated correctly at each end and try another cable if the problem persists.

  • Since dowloading Ios7, my ipad cannot connect to 3G and when I have no wireless or 3G connection, it closes down and reboots every 2 minutes or so. This happened in central Manchester and also on the Virgin Train from Man. to London. Totally unusable.

    Since downloading IOS 702 I cannot access 3G. Also when I have no access to wireless connection my ipad closes down and reboots every couple of minutes. I was trying to raed a book on a train from Manchester to Euston and had to give up. I found that auto-lock had defaulted to 2 minutes. I changed it to never but it made no difference.

        jsavage9621,
    It pains me to hear about your experience with the Home Phone Connect.  This device usually works seamlessly and is a great alternative to a landline phone.  It sounds like we've done our fair share of work on your account here.  I'm going to go ahead and send you a Private Message so that we can access your account and review any open tickets for you.  I look forward to speaking with you.
    TrevorC_VZW
    Follow us on Twitter @VZWSupport

  • WRT160Nv3 rebooting every 1-20 minutes

    Dear All,
    After installation of WRT160Nv3 and firmware upgrade router rebooting every 1-20 minutes. 
    I did reset using hardware button and reboot from Web interface; returned to factory defaults and back to my settings - problem still the same.
    Any suggestions?

    Well... thanks. I re-loaded  the firmware - nothing changed. 
    Actualy now I suspect that someone in the provider's network installed (or re-configured) an equipment  (computer or router) that works in wrong way - for instance gives IP to WAN.
    Unfortunately WRT160N writes log in RAM and all records disappear during rebooting - so I can't trace the cause. But when I disconnect the WAN socket in router it works stable. When it connected to provider - it may work for several hours perfectly, but in rush hours it start rebooting

  • Fresh installation of 2012r2 on PowerEdge r620 rebooting every 10 minutes

    Installed 2012r2 Standard Evaluation on a Dell PowerEdge r620 today. In response to a failing 2003 DC. It's rebooting every 10 minutes or so with an lsass error.
    A critical system process, C:\Windows\system32\lsass.exe, failed with status code c0000005.  The machine must now be restarted.
    I'm doubly concerned as in the process I raised the forest level from 2000 to 2003 (We still have 2 2003 DCs, one of them the struggling one) I've promoted it to DC and transferred the FSMO already. I've got the weekend to get it sorted...
    It's my first server install and I just did a straight bare metal install without installing Dell drivers. I'm thinking this may be my problem...
    Any advice greatly appreciated.
    Neil

    After reading so much about the irreversibility of raising the forest level once offline DCs have been added again I was cautious about adding the previously downed DR DC. However the FSMO roles and AD replication were struggling so, after some consideration,
    I brought the offending DC back online (AD has not been actively maintained for more than a couple of years...)
    Initial signs were good. Replication was happening. 
    However, my process involved replicating across to the new server data from more than one source (The org had suffered from server spread over the past few years). In the process of consolidating the DFSR namespaces and shares, and removing legacy FSR replication
    I hit problems with deleted namespaces and replication groups lingering and not being able to be deleted. I tried to follow various diagnostic and recovery methods. See this post. My main concerns continue there... :-
    Bah. Can't post link. Account not verified yet. Will edit in due course. Check my profile for the DFSR related thread...
    Not wishing to jinx it but the AD looks fairly stable now. Slight concern is repeated system log entries indicating :-
    The DFS Namespaces service has successfully initialized the shared folder that hosts the namespace root. Shared folder: *********
    Would be great to get rid of them.

  • I bought iphone 4 yesterday....since i boot every 3 to 4 minutes its restarting automatically.......pls advice me

    i bought a iphone 4 from du network in united arab emirates yesterday....since i bought it it rebooting every 2 minutes.at the same time i charge it for more then 6 hours even though it showing only 25% of bettery level....Model no-A1332 Emc 3808 FCC id:BCG -E23808 IC 579c-E23808..I M REALLY UN HAPPY NOW...only one day even i cannpt use prpperly.......pls advice me

    You just bought it yesterday? Just take it back and exchange it. It definitely should NOT be doing that out of the box.

  • Help with BT Vision Box - rebooting every 15-20min...

    I need help with this please!! I have been unable to watch TV using the Vision Box since last week as the box is rebooting itself at least every 15 to 20 minutes. It is impossible to record anything as the box drops out and then we cannot watch the shows. I am getting increasingly frustrated as I feel that what I am paying does not reflect the service I am getting from BT.

    Hi SineadMcB,
    Welcome and thanks for posting. I can look into this for you. Drop me an email with the details. You'll find the "contact us" form in the about me section of my profile.
    Cheers
    David
    BTCare Community Mod
    If we have asked you to email us with your details, please make sure you are logged in to the forum, otherwise you will not be able to see our ‘Contact Us’ link within our profiles.
    We are sorry but we are unable to deal with service/account queries via the private message(PM) function so please don't PM your account info, we need to deal with this via our email account :-)

  • WRT350N Rebooting every hour.

    Hey All,
       I bought my WRT350N back in January from Best Buy.
    I haven't had a single problem from it until recently. I very much love this router...but I upgraded the firmware..and my life is now hell. Every 30 to 60 minutes the router reboots. Also...where it used to send out 54mbps to my wife's laptop..I'm lucky to get 24 out of it. Anyone have any ideas?
    Tomcat

    I'm having the same issue as the OP. I updated to the latest firmware Firmware Version: v1.03.7 on my WRT350N
    And now the router reboots at random about once an hour to hour and a half.
    up till now it's ran perfect for just over a year.

  • SPA112 Reboot every 72 hours (3 days) exactly.

    Hi,
    I have a Cisco SPA112 which connects to a 3CX server. I also have addional phones, inluding Cisco SPA504G phones.
    The issue I have is the SPA112 reboots every 3 days, exactly to the minute. This has happened 3 times now. The 504G is fine (40+ days uptime)
    Nothing has changed on the provisioning of the ATA, when I do change things it reboots at 02:00 as expected, so I don't think this is related to reprovisioning.
    I can provide more information e.g. logs if required, but thought I'd initially check if there is possibly a setting somewhere that I am unaware of that would cause this reboot every 72 hours exactly.
    Thanks in advance,
    Marcus

    I should have included this information:
    Product Information
    Product Name:   
    SPA112
    Serial Number:   
    CCQ162503NC
    Software Version:   
    1.2.1(004)
    Hardware Version:   
    1.0.0
    MAC Address:   
    C40ACBBC7XXX
    Client Certificate:   
    Installed
    Customization:   
    Open
    System Status
    Current Time:   
    9/9/2012 22:13:41
    Elapsed Time:   
    00:35:12
    RTP Packets Sent:   
    0
    RTP Bytes Sent:   
    0
    RTP Packets Recv:   
    0
    RTP Bytes Recv:   
    0
    SIP Messages Sent:   
    24
    SIP Bytes Sent:   
    20821
    SIP Messages Recv:   
    23
    SIP Bytes Recv:   
    10833
    As you can see the elapsed time is 35 mins, this ties in with the reboot event.

  • OS4 upgrade = error 29 then reboot every few min. on use

    Tried to upgrade my iphone to os4 last night and got an error 29 message and was then stuck in an endless reconnect to itunes loop. Restore only resulted in further error 29 messages. Finally after a good bit of searching on potential solutions I used irecovery to escape the loop. Now os4 is on my iphone (and looks great!) but it reboots every few minutes (2-3) when being used. It does not reboot if off. I tried restoring again after discovering the reboot problem but that got me back to square one and error 29 messages again.
    Noticed some others with similar issues but didn't see a thread with this exact problem posted.
    Perhaps it's worth noting that I replaced my iphone battery myself a few months ago but had no issues at all until now. Not a jailbroken iphone. Just trying to get it to work.

    mrrutter wrote:
    Tried to upgrade my iphone to os4 last night and got an error 29 message and was then stuck in an endless reconnect to itunes loop. Restore only resulted in further error 29 messages. Finally after a good bit of searching on potential solutions I used irecovery to escape the loop. Now os4 is on my iphone (and looks great!) but it reboots every few minutes (2-3) when being used. It does not reboot if off. I tried restoring again after discovering the reboot problem but that got me back to square one and error 29 messages again.
    Noticed some others with similar issues but didn't see a thread with this exact problem posted.
    Perhaps it's worth noting that I replaced my iphone battery myself a few months ago but had no issues at all until now. Not a jailbroken iphone. Just trying to get it to work.
    Ok. From reading through the forums some more it definitely seems to be related to the battery. Perhaps for some it's because they have a semi-bad original/OEM battery. For me I'm guessing it's because I installed a non-OEM battery when my original started to fail. I bought a higher capacity replacement than OEM off the internet thinking it would give me better battery life. It worked perfectly fine until upgrading iOS4. In addition to previous problems posted my battery is either not charging at all now or charging very slowly. It reboots even as I'm trying to recharge. I've turned it off while trying to recharge it now in the hopes that this will make it charge properly. I've also ordered an OEM battery now in the hopes this will fix the problem. Wish I hadn't discarded the original. Odd that an OS upgrade would cause this problem. The tinfoil hat part of me wonders if Apple did this on purpose to discourage DIY fixes. If so, that's really uncool of you, Apple. If I break my phone fixing it myself then let me break it. Please don't break it for me.
    Once I get an OEM battery and install it I will update on whether that worked for me or not.
    Here's a post from another thread concerning error 29:
    Hi all,
    I am so happy! I can confirm the error 29 has been resolved and it is to do with the battery gauge. I ordered a higher capacity battery from Ebay, that messed around with the readout in 3.1.3. I was on the verge on making a claim for a replacement iphone until just now. Also as a word of warning, Non apple OEM battery will cause the phone to crash. Maybe the phone is sensitive to calculating the gas gauge so when it can't work out the exact charge it'll force the phone to reboot every 5 minute interval, this is apples ploy to dig out illegal modifications? This is very interesting, Phone fully functional now after installing OEM battery. I will now install the bigger capacity battery to see if it is compatible with it. I'm guessing not.

  • Hello guys..!! I have got my new  iphone 4 2 days ago.The same day it got a problem of auto restart in every 1, to 2 minutes. I updated and restored it many times...but of no use... can any one help me how to solve this problem..!!

    Hello guys..!! I have got my new  iphone 4 2 days ago.The same day it got a problem of auto restart in every 1, to 2 minutes. I updated and restored it many times...but of no use... can any one help me how to solve this problem..!!

    Go to Settings/General/Reset - Erase all content and settings. the connecto to iTunes and restore as a New phone. Do not restore any backup. If the problem persists you have a hardware problem. Take it to Apple for exchange.
    This assumes that the phone is not hacked or jailbroken. If it is you will have to go elsewhere on the internet for help.

Maybe you are looking for

  • Change mouse pointer over selected text

    I have a JTextArea and i want to change the default mouse pointer to the arrow pointer when the user points to a selected text. Just like the way JCreator works.! Thanx

  • Time and Date - Clock Widget missing from home scr...

    What is the solution for missing clock widget from home screen after Anna update from Nokia Care !!! Reinstalled from Nokia Suite, still clock missing - any solution.

  • Event ID: 6875 Error

    Dear All, I found below error repeating in my event logs. "Error loading and running event receiver Microsoft.SharePoint.Publishing.Internal.PublishingWebEventReceiver in Microsoft.SharePoint.Publishing, Version=14.0.0.0, Culture=neutral, PublicKeyTo

  • Using Borders in Lightroom

    Lightroom doesn't ship with frames or custom borders, but as you may know from Sid Jervis of LightroomExtra.com, Andreas Norén found a way around this. I've just posted a video tutorial on getting frames in the Print Module that differs from the way

  • TR Releasing problem

    Hi Everybody, I have got some problem releasing Request from DEV to PRD. when i try to release a TR child, it says, Create Document for Task when i try to release its Parent, it says, "The system administration lets you make the release in the backgr