Ipad2 restore failed due to cable disconnect

Hello, I have an ipad2. I was trying to restore the ipad due to lost password. During the restore, the cable got disconnected.
Now I have an unusable ipad. It stays on itunes/recovery screen.
When I connect it to the laptop, it tries to do restore/update then it comes back 'The ipad could not be updated. The device cannot be found'.
My computer's USB does not recognize this ipad due to corrupted firmware as a result of failed restore.
What can be done?

Hold both buttons and turn screen black again... What happens when you touch power button? does it turn back on to the itunes/recovery screen? Or try holding power button until you see the slide to power off appear... then hold both buttons for hard restart... If nothing else call Apple.. they will still help if you schedule a phone call online.. They will call you... no $$$$ needed...

Similar Messages

Restore failed due to iTunes being corrupt

Attempting to restore from a 'successful' backup got a warning message the restore failed due to a iTunes being corrupt. Found the following log
2013-06-19 13:14:14.979 [8216:f38]: restore library built Dec 21 2012 at 16:17:03
2013-06-19 13:14:14.979 [8216:f38]: iTunes: iTunes 11.0.4.4
2013-06-19 13:14:15.041 [8216:f38]: iTunes: Current software version: 10B329
2013-06-19 13:14:15.042 [8216:f38]: iTunes: Software payload version: 10B329
2013-06-19 13:14:15.042 [8216:f38]: iTunes: Using iTunes state machine
2013-06-19 13:14:15.636 [8216:f38]: iTunes: Restore error -34
The SAD thing is not only is all my data gone but the phone is not usable it is stuck on a setup screen.
Please help – What has happened to Apple????????????????????

Well I found a article that may help you.
Error 34:
These errors typically occur when security software interferes with the restore and update process. Follow Troubleshooting security software issues to resolve this issue. In rare cases, these errors may be a hardware issue. If the errors persist on another computer, the device may need service.
Also, check your hosts file to verify that it's not blocking iTunes from communicating with the update server. See iTunes: Advanced iTunes Store troubleshooting—follow steps under the heading Blocked by configuration (Mac OS X / Windows) > Rebuild network information > Mac OS X > The hosts file may also be blocking the iTunes Store. If you have software used to perform unauthorized modifications to the iOS device, uninstall this software prior to editing the hosts file to prevent that software from automatically modifying the hosts file again on restart.
http://support.apple.com/kb/TS3694

RMAN restore fails due to space issue

Hi,
My database size is 225 GB . I m restoring the backupfiles using RMAN from production backup to the test instance.During restore process rman failed due to space issue.When the error occurred rman restored around 122 GB.
Now i increased the free space in server.So now my doubt is i have to delete the restored files (122GB) and start the restore process again or RMAN will automatically skip the the restored file and resume the process from where it was failed ?
DB Version -11.2.0.2
RMAN error
channel CH2: ORA-19870: error while restoring backup piece /ebs/DEV/backup/GOLD_db_t801111628_s10788_p1.rman
ORA-19502: write error on file "/ebs/DEV/bin/db/apps_st/data/a_txn_data11.dbf", block number 3492608 (block size=8192)
ORA-27072: File I/O error
Linux-x86_64 Error: 28: No space left on device
Additional information: 4
Additional information: 3492608
Additional information: -1
Thanks

When you start the restore from the failure, RMAN knows whcih are restored and it will check file headers. if the headers match, it will skip restoring the files.
Hope this helps,
Regards,
http://www.oracleracexpert.com
RMAN Debug and Trace
http://www.oracleracexpert.com/2012/11/rman-debug-and-trace.html
Time for Change: Migrate your Non-RAC Database to RAC
http://www.oracleracexpert.com/2012/10/time-for-change-migrate-your-non-rac.html

Yoga 13 System Image Restore Fails Due To Excluded Disk

Hello:
I am trying to execute a restore from a system image disc created shortly after I installed my principal programs without destroying the OKR partition or files. However, I do not want to go all the way back to factory condition at this time. The issue is that when I attempt to follow the reimage instructions in win 8.1, I am presented with a dialog box that has two check boxes. The first asks "Format and repartition disk" and the second asks "only restore system drives".
Based on everything I've read about preserving the C:/ and D:/ drive partitions, I would have expected to check the second box and not the first. But the system will not let me make this choice. Instead, the first box is automatically checked, and greyed out, with a second dialogue asking me if there are any disks I want to exclude from repartitioning. When following this second dialogue I am asked if I want to exclude Disk 0 (Samsung MZMTD128HAfV -00l1) which has 119Gb of capacity. If I try to exclude this disk, the operation fails with following error: "Restore failed because a disk that was critical at backup is excluded" My question is, if I do not exclude this disk, will the restore operation still leave the D:/ partition intact so I can use OKR in the future.
I have read quite a bit of imformation here and elsewhere about restoring system images and OKR, but have not seen any discussion about this disalogue, or the fact that I am being forced to reformat and repartition the disk without excluding the d:/ drive. Other posters have stated that retsoringa system image will only restore C;? drive, but this dialogue seems to conflict with those statements. Anyone else have any experience with this operation?
Thank you,

Hello:
I am trying to execute a restore from a system image disc created shortly after I installed my principal programs without destroying the OKR partition or files. However, I do not want to go all the way back to factory condition at this time. The issue is that when I attempt to follow the reimage instructions in win 8.1, I am presented with a dialog box that has two check boxes. The first asks "Format and repartition disk" and the second asks "only restore system drives".
Based on everything I've read about preserving the C:/ and D:/ drive partitions, I would have expected to check the second box and not the first. But the system will not let me make this choice. Instead, the first box is automatically checked, and greyed out, with a second dialogue asking me if there are any disks I want to exclude from repartitioning. When following this second dialogue I am asked if I want to exclude Disk 0 (Samsung MZMTD128HAfV -00l1) which has 119Gb of capacity. If I try to exclude this disk, the operation fails with following error: "Restore failed because a disk that was critical at backup is excluded" My question is, if I do not exclude this disk, will the restore operation still leave the D:/ partition intact so I can use OKR in the future.
I have read quite a bit of imformation here and elsewhere about restoring system images and OKR, but have not seen any discussion about this disalogue, or the fact that I am being forced to reformat and repartition the disk without excluding the d:/ drive. Other posters have stated that retsoringa system image will only restore C;? drive, but this dialogue seems to conflict with those statements. Anyone else have any experience with this operation?
Thank you,

Ipad2 restore fails with unknown error(1) with "iTunes and recovery" mode logo

Ipad2 64GB was sluggish and we tried to update with latest iOS update, security 2014-005 and latest iTunes on iMac 12.01 It enters a recoverymode with the iTunes logo and connector symbol displayed on the screen. Recognized that iPad is connected and proceeded to restore to factory condition. Goes through several stages, FW verification, restore etc but fails to proceed past a certain point and puts up an unknown error (1) occurred message. Disabled firewall and tried restore and it failed in the same spot. Tried using power + home button combos to enter DFW or restore mode. None of them worked. Took it to the Apple store and was told that it can't be debugged further because it did not yet boot up ( if it has the iTunes and connector symbol it must be in some state that it can be interacted with?) It's physically in a perfectly beautiful condition, nothing funky (jail breaking etc ) done to it, well taken care of. The tech said that he can offer a replacement for 299$ after he tried to restore it twice without success. I am surprised that this tech thinks that it cannot be probed with some low level FW tools through the serial connector to determine the system state. Any suggestions?

Hey Ngtrishank,
Thanks for the question. Based on the information you have provided, I concur with the Apple Store’s conclusion. Error 1 is usually related to a hardware issue with the device. While there are a few steps you can attempt in the following resource, in most cases Error 1 signifies that the device needs to be serviced. For more information on troubleshooting Error 1, see this article:
Resolve iOS update and restore errors - Apple Support
http://support.apple.com/en-us/ts3694
Check for hardware issues
Related errors: 1, 3, 10, 11, 12, 13, 14, 16, 20, 21, 23, 26, 27, 28, 29, 34, 35, 36, 37, 40, 1000, 1002, 1004, 1011, 1012, 1014, 1667, or 1669.
These errors mean that your device or computer may have a hardware issue that's preventing the update or restore from completing.
If you’d like to learn more about your Service options for this device, check out the following link:
iPad Other Repair Options - Apple Support
http://www.apple.com/support/ipad/repair/other/
Thanks,
Matt M.

RESTORE failure: "due to unknown error"

ITunes prompted me to install latest update. Install failed and IPhone locked. Got message that indicated IPhone was in recovery mode and needed to be restored. Have attempted restore several times, which always fails with a message that says, "Restore failed due to unknown error." Any suggestions as to how to proceed? Thanks.

exact same thing happened to me when updating to the 2.02 software, error code 2005. i realized that i was using the cable from my originial iphone. it works to charge the 3G iphone and sync, but apparently not to update software. and they are almost impossible to tell apart.
switched to the 3G cable and all was updated and restored. you would think they would either make the cables compatible or clearly identify them as different.

Ipod restore failed can see on the screen is the cable connection symbom and the ipod does not appear in the LH panel of itunes is there an easy solution to this

ipod restore failed can see on the screen is the cable connection symbom and the ipod does not appear in the LH panel of itunes is there an easy solution to this

To get iTunes to see your iPod try:
- Placing the iPod in recovery mode. See:
iPhone and iPod touch: Unable to update or restore
- Placing it in recovery DFU mode:
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- Sometimes this program will get th iPod in recovery mode:
RecBoot iPod-1.0.2-Mac-Jaxov.zip - File Shared from Box.net - Free Online File Storage

My daughter has not used her ipod touch for 16 months and has forgotten her passcode. restore factory settings keeps failing due to a software update failure!

my daughter has not used her ipod touch for 16 months and has forgotten her passcode. restore factory settings keeps failing due to a software update failure!
how can i get this ipod reset. She now has an iphone so this is going to be used by someone else in the family and should be simple to do but itunes just keeps booting it out even though it recognises that it was previously connected to our itunes account as all of the children were on my account

That has nothing to do with an update server. Do the following:
Place the iOS device in Recovery Mode and then connect to your computer and restore via iTunes. The iPod will be erased.
iOS: Forgot passcode or device disabled
If recovery mode does not work try DFU mode.
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
For how to restore:
iTunes: Restoring iOS software
To restore from backup see:
iOS: Back up and restore your iOS device with iCloud or iTunes
If you restore from iCloud backup the apps will be automatically downloaded. If you restore from iTunes backup the apps and music have to be in the iTunes library since synced media like apps and music are not included in the backup of the iOS device that iTunes makes.
You can redownload most iTunes purchases by:
Downloading past purchases from the App Store, iBookstore, and iTunes Store
If problem what happens or does not happen and when in the instructions? When you successfully get the iPod in recovery mode and connect to computer iTunes

System Image Restore Fails "No disk that can be used for recovering the system disk can be found"

Greetings
                                    - Our critical server image backup Fails on one
server -
Two 2008 R2 servers. Both do a nightly "Windows Server Backup" of Bare Metal Recovery, System State, C:, System Reserved partition, to another storage hard drive on the same machine as the source. Active Directory is on the C: The much larger D: data
partition on each source hard drive is not included.
Test recovery by disconnecting 500G System drive, booting from 2008R2 Install DVD, recovering to a new 500G SATA hard drive.
Server A good.
Server B fails. It finds the backed-up image, & then we can select the date we want. As soon as the image restore is beginning and the timeline appears, it bombs with "The system image restore failed. No disk that can be used for recovering the system
disk can be found." There is a wordy Details message but none of it seems relevant (we are not using USB etc).
At some point after this, in one (or two?) of the scenarios below, (I forget exactly where) we also got :
"The system image restore failed. (0x80042403)"
The destination drive is Not "Excluded".
Used   diskpart clean   to remove volumes from destination drive. Recovery still errored.
Tried a second restore-to drive, same make/model Seagate ST3500418AS, fails.
Tried the earliest dated B image rather than the most recent, fail.
The Server B backups show as "Success" each night.
Copied image from B to the same storage drive on A where the A backup image is kept, and used the A hardware to attempt restore. Now only the latest backup date is available (as would occur normally if we had originally saved the backup to a network location).
Restore still fails.         It looks like its to do with the image rather than with the hardware.
Tried unticking "automatically check and update disk error info", still fail.
Server A SRP 100MB C: 50.6GB on Seagate ST3500418AS 465.76GB Microsoft driver 6.1.7600.16385   write cache off
Server B SRP 100MB C: 102GB on Seagate ST3500418AS 465.76GB Microsoft driver 6.1.7600.16385   write cache off
Restore-to hard drive is also Seagate ST3500418AS.
http://social.answers.microsoft.com/Forums/en-US/w7repair/thread/e855ee43-186d-4200-a032-23d214d3d524      Some people report success after diskpart clean, but not us.
http://social.technet.microsoft.com/Forums/en-US/windowsbackup/thread/31595afd-396f-4084-b5fc-f80b6f40dbeb
"If your destination disk has a lower capacity than the source disk, you need to go into the disk manager and shrink each partition on the source disk before restoring." Doesnt apply here.
http://benchmarkreviews.com/index.php?option=com_content&task=view&id=439&Itemid=38&limit=1&limitstart=4
for 0x80042403 says "The solution is really quite simple: the destination drive is of a lower capacity than the image's source drive." I cant see that here.
Thank you so much.

Hello,
1. While recovering the OS to the new Hard disk, please don't keep the original boot disk attached to the System. There is a Disk signature for each hard disk. The signature will collide if the original boot disk signature is assigned to the new disk.
You may attach the older disk after recovering the OS. If you want to recover data to the older disk then they should be attached as they were during backup.
2. Make sure that the new boot disk is attached as the First Boot disk in hardware (IDE/SATA port 0/master) and is the first disk in boot order priority.
3. In Windows Recovery Env (WinRE) check the Boot disk using: Cmd prompt -> Diskpart.exe -> Select Disk = System. This will show the disk where OS restore will be attempted. If the disk is different than the intended 2 TB disk then swap the disks in
correct order in the hardware.
4. Please make sure that the OS is always recovered to the System disk. (Due to an issue: BMR might recover the OS to some other disk if System disk is small in size. Here the OS won't boot. If you belive this is the case, then you should attach the
bigger sized disk as System disk and/or exclude other disks from recovery). Disk exclusion is provided in System Image Restore/Complete PC Restore UI/cmdline.
5. Make sure that Number and Size of disks during restore match the backup config. Apart from boot volumes, some other volumes are also considered critical if there are services/roles installed on them. These disks will be marked critical for recovery and
should be present with minimum size requirement.
6. Some other requirements are discussed in following newsgroup threads:
http://social.technet.microsoft.com/Forums/en-US/windowsbackup/thread/871a0216-fbaf-4a0c-83aa-1e02ae90dbe4
http://social.technet.microsoft.com/Forums/en-US/windowsbackup/thread/9a082b90-bd7c-46f8-9eb3-9581f9d5efdd
http://social.technet.microsoft.com/Forums/en-US/windowsbackup/thread/11d8c552-a841-49ac-ab2e-445e6f95e704
Regards,
Vikas Ranjan [MSFT]
------- This information is provided as-is without any warranties, implicit or explicit.-------

IPhone 5 firmware restore failed (unknown error 1)

hi everyone,
I updated my iPhone 5 from ISO 6.1.2 to 7.1.1 via iTunes by restoring and it was working fine but when 7.1.2 update came n I was trying to install via wifi, it failed a lot of times. so I connect my iphone to iTunes n tried by restore iphone, during this my phone was restated and it never showed up on iTunes so I disconnect iphone, since that time iphone is in recovey mode, now whenever I connects iphone to iTunes, a msg pop up on iTunes "iTunes detected an iphone in recovery mode. You must restore this iPhone before it can be used with iTunes." so I click on and then I click on restore and update. it goes for Extracting Software> Restoring iPhone software>verifying iPhone software>restoring iPhone firmware but never completes, a msg comes on iTunes iPhone restore failed. unknown error(1) I does the same like I m putting a link from someone for iphone 5s.
https://www.youtube.com/watch?v=vQq9P0xiSGk
if someone has a solution please share with me asap.
Thanks

Check for hardware issues
Related errors: 1, 3, 10, 11, 12, 13, 14, 16, 20, 21, 23, 26, 27, 28, 29, 34, 35, 36, 37, 40, 1000, 1002, 1004, 1011, 1012, 1014, 1667, or 1669.
These errors mean that your device or computer may have a hardware issue that's preventing the update or restore from completing.
Check that your security software and settings aren't preventing your device from communicating with the Apple update server.
Then try to restore your iOS device two more times while connected with a cable, computer, and network you know are good.
Confirm that your security software and settings are allowing communication between your device and update servers.
If you still see the error message when you update or restore, contact Apple support.

ITunes could not restore iPhone because the iPhone disconnected

I cannot restore my iPhone from my encrypted backup. iTunes begins the restore process displaying 2 hours remaining and after about 45 minutes I get a message on the screen that iTunes could not restore the iPhone because it disconnected. It also says restore failed in the phone.
I have tried multiple things: reinstalling iTunes, resetting sync history, trying to restore on an IPhone 3GS, trying a different cable and both USB ports on my computer and unchecking the 'allow computer to turn off this device to save power' in the USB options on device manager.
I visited the Apple store after exhausted all of the options I listed and they suggested try restoring from another computer. They said it is not a corrupted backup. I tried on another windows laptop but that did not work either.
The size of the backup is 14.8gb. It took approx. an hour to backup the phone.
I found others with the similar problem on this thread. Theirs is not a restore problem it's a backup one.
https://discussions.apple.com/thread/2453974?threadID=2453974
I have searched google and have found iPad users with the same problem:
https://discussions.apple.com/message/12708983?messageID=12708983

I have the same problem, I can not restore data to my mobile
Please help ...
Is there a way to remove the encryption in itunes?
Without restoring the mobile?
Because the restore fail for mobile ..
I have a password for encryption
I want to remove the encryption so I can take the files manually from the backup in my computer
Thank you

HT1766 My Iphone screen is frozen as "Restore Failed. Can someone help?

I just receive a company issued Iphone 5. I wanted to download music from my wifes MacBook through our iTunes files. So I connected the devise to the MacBook. I can't remember all the steps but it started to Restore my device idicating it was restoring my wife's Iphone. I paniced thinking that my company phone would can restored with my wifes stuff so I unplugged it from the MacBook. Now the phone screed is frozen at "Restore failed" and I don't know what to do. Can someone help me to get the phone to work.

Hello Georgept,
If the iPhone was disconnected while it was going through a process, you may need to put it in recovery mode and restore it. If you have a backup of your phone on the iCloud, or iTunes on the computer for that matter, after the restore you will be presented with the set-up screens and will have the option to restore from an iCloud or iTunes backup to bring all of your data back. The following article has the steps for putting the iPhone into recovery mode and restoring.
If you can't update or restore your iOS device
http://support.apple.com/kb/ht1808
Use recovery mode
Recovery mode erases your device and restores it, which should resolve the issue. If you previously synced with iTunes or iCloud, you may be able to restore from your backup after recovery.
Turn off your device. If you can't turn it off, press and hold the Sleep/Wake and Home buttons at the same time and wait a few seconds for it to turn off.
Plug the device's USB cable into your computer only.
Hold down the device's Home button as you connect the USB cable to it.
When you see the Connect to iTunes screen, release the Home button. If you don't see this screen, try steps 1 through 3 one more time.
iTunes should open and display a message such as: "iTunes has detected an iPhone in recovery mode. You must restore this iPhone before it can be used with iTunes."
5. Use iTunes to restore your device.
If you don't see your device in iTunes, follow these steps for Mac or these for Windows.
Once the iPhone has been restored, you can use this article as a reference for restoring from your iCloud or iTunes backup to recover your data.
iOS: Back up and restore your iOS device with iCloud or iTunes
http://support.apple.com/kb/ht1766
Thanks for reaching out,
-Joe

HT1212 I am unable to get our of a continuous cycle when trying to update or restore my iPad 2. Plug in to iTunes 12.0.1 (latest version). Click update, told can't update, have to restore. Restore fails with error 9. Any help appreciated.

When I tried to update my iPad I got an error 9. Now, I am unable to access my iPad. It is in a continuous cycle when I try to update or restore the iPad 2. Plug in to iTunes 12.0.1 (latest version). Click update, told can't update, have to restore. Restore fails with error 9. Any help appreciated.
Here's the cycle:
I plug in my iPad when “cable to iTunes shows on iPad screen. It says "Your iPad can't be updated, you must restore it to factory settings." That bad enough news, but it gets worse.
Click Restore
Extracting software…
Preparing iPad for restore
Waiting for iPad…
Verifying iPad restore with Apple…
(empty bar under the Apple logo…does not show any activity)
“The iPad “iPad” could not be restored. An unknown error occurred (9).”
Notes: I just upgraded to OS X Yosemite 10.10.1 on my iMac (27-inch, Mid 2011) in the last week. It’s the first time I’m tried to backup/update my iPad since the iMac update.
I swapped out the USB cable to a new cable and get the same results.
I also unplugged all other USB devices from the iMac and security on my iPad and still get the same results.
I find it strange that it shows no Serial number for my my iPad 2 when plugged in. It shows “Serial Number: n/a on the screen when it displays: “iPad Recovery Mode To update your iPad without erasing its contents, click Update. To restore your iPad to its factory settings, click Restore iPad.
I prefer to update my iPad, but it displays “Your iPad can’t be updated, you must restore it to factory settings. If you previously backed up the iPad, click Restore Backup after the restore process completes.”
It’s a continuous loop. I get the display on my iPad to plug in the iPad to iTunes, plug it in which ends after going through the above procedure saying an error occurred (9).
So now I cannot use my iPad. When I turn it on I get the display showing me to plug it into iTunes with the cable. Since this is the only option I have I plug it in and the loop begins.
Any advice would be appreciated.
Thanks!

Hello jaybearden,
Thanks for the question. After reviewing your post, it sounds like you are not able to restore the iOS device since you get an error 9. I would recommend that you read this article, it may be able to help the issue.
Resolve iOS update and restore errors - Apple Support
Check your security software
Related errors: 2, 4, 6, 9, 1000, 1611, 9006. Sometimes security software can prevent your device from communicating with either the Apple update server or with your device.
Check your security software and settings to make sure that they aren't preventing a connection to the Apple servers.
Thanks for using Apple Support Communities.
Have a nice day,
Mario

My IPOD Touch initially had a white screen. I tried correcting this by restoring default settings via ITunes. The Restore Failed with error 1602 and now the IPOD touch is completely dead. It will not power on or respond when I plug it into my PC via USB

My IPOD Touch initially had a white screen. I tried correcting this by restoring default settings via ITunes. The Restore Failed with error 1602 and now the IPOD touch is completely dead. It will not power on or respond when I plug it into my PC via USB. I get an error on my PC stating that device attached to USB port is not recognizable. Can anyone help?

Error 1602: Try the following steps to resolve this error:
Ensure proper USB isolation troubleshooting has been performed, and test with a known-good cable.
Follow the steps listed for Error 1604.
This error may be resolved by disabling, deactivating, or uninstalling third-party security, antivirus, and firewall software. See steps in this article for details on troubleshooting security software.
Above from:
http://support.apple.com/kb/TS3694

JDBC initialize failed due to long idling time

Hi gurus
Anyone having similar problem and would like to share their solution for the problem stated below.
Normally the integration for IDOC-XI-JDBC scenarios is working fine, but when the R3 halt sending IDOC to XI, the JDBC connection to MS SQL 2000 server failed to process and initialise due to long idling time. Currently the temporary solution is to go to XI change the Integration Directory : Communication Channel for the JDBC - Activate - Clear Cache. Then go to R3, retrigger the IDOC again. And the above problem will be resolved. But after a while (long idling time again), this problem arise once again.
2008-10-21 15:18:45     Success     Message successfully received by messaging system. Profile: XI URL: http://locahost:50600/MessagingSystem/receive/AFW/XI Credential (User): PIISUSER
2008-10-21 15:18:45     Success     Using connection JDBC_http://sap.com/xi/XI/System. Trying to put the message into the receive queue.
2008-10-21 15:18:45     Success     Message successfully put into the queue.
2008-10-21 15:18:45     Success     The message was successfully retrieved from the receive queue.
2008-10-21 15:18:45     Success     The message status set to DLNG.
2008-10-21 15:18:45     Success     Delivering to channel: CC_IDOC_TO_DBMS_ESMS_588
2008-10-21 15:18:45     Success     MP: Entering module processor
2008-10-21 15:18:45     Success     MP: Processing local module localejbs/CallSapAdapter
2008-10-21 15:18:45     Success     Receiver JDBC adapter: processing started; QoS required: ExactlyOnce
2008-10-21 15:18:45     Error     JDBC adapter receiver channel CC_IDOC_TO_DBMS_ESMS_588 not initialized. Unable to proceed due to null
2008-10-21 15:18:46     Error     MP: Exception caught with cause com.sap.aii.af.ra.ms.api.RecoverableException: JDBC Adapter configuration not initialized: null
2008-10-21 15:18:46     Error     Exception caught by adapter framework: JDBC Adapter configuration not initialized: null
2008-10-21 15:18:46     Error     Delivery of the message to the application using connection JDBC_http://sap.com/xi/XI/System failed, due to: com.sap.aii.af.ra.ms.api.RecoverableException: JDBC Adapter configuration not initialized: null.
2008-10-21 15:18:46     Success     The message status set to WAIT.
2008-10-21 15:18:46     Success     The asynchronous message was successfully scheduled to be delivered at Tue Oct 21 15:23:46 GMT+08:00 2008.
2008-10-21 15:23:46     Success     The message status set to TBDL.
2008-10-21 15:23:46     Success     Retrying to deliver message to the application. Retry: 1
2008-10-21 15:23:46     Success     The message was successfully retrieved from the receive queue.
2008-10-21 15:23:46     Success     The message status set to DLNG.
2008-10-21 15:23:46     Success     Delivering to channel: CC_IDOC_TO_DBMS_ESMS_588
2008-10-21 15:23:46     Success     MP: Entering module processor
2008-10-21 15:23:46     Success     MP: Processing local module localejbs/CallSapAdapter
2008-10-21 15:23:46     Success     Receiver JDBC adapter: processing started; QoS required: ExactlyOnce
2008-10-21 15:23:46     Error     JDBC adapter receiver channel CC_IDOC_TO_DBMS_ESMS_588 not initialized. Unable to proceed due to null
2008-10-21 15:23:46     Error     MP: Exception caught with cause com.sap.aii.af.ra.ms.api.RecoverableException: JDBC Adapter configuration not initialized: null
2008-10-21 15:23:46     Error     Exception caught by adapter framework: JDBC Adapter configuration not initialized: null
2008-10-21 15:23:46     Error     Delivery of the message to the application using connection JDBC_http://sap.com/xi/XI/System failed, due to: com.sap.aii.af.ra.ms.api.RecoverableException: JDBC Adapter configuration not initialized: null.
2008-10-21 15:23:46     Success     The message status set to WAIT.
2008-10-21 15:23:46     Success     The asynchronous message was successfully scheduled to be delivered at Tue Oct 21 15:28:46 GMT+08:00 2008.
2008-10-21 15:28:46     Success     The message status set to TBDL.
Edited by: Malcolm Pang on Oct 23, 2008 11:08 AM

In the JDBC adapter , select option Disconnect From Database after Each message processing.
This will solve the process as your JDBC Database seems to be closing the connection after a particular idle time.
Regards
Bhavesh

Ipad2 restore failed due to cable disconnect

Similar Messages

Maybe you are looking for