Ipad2 will not charge after ios7

Tried reset many times.  Tried several apple cords.

Try this first - Reset the iPad by holding down on the Sleep and Home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons. (This is equivalent to rebooting your computer.)
The quickest way (and really the only way) to charge your iPad is with the included 10W or 12W (5W on Mini) USB Power Adapter. iPad will also charge, although more slowly, when attached to a computer with a high-power USB port (many recent Mac computers) or with an iPhone Power Adapter (5W). When attached to a computer via a standard USB port (2.5W, most PCs or older Mac computers) iPad will charge very slowly (but iPad indicates not charging). Make sure your computer is on while charging iPad via USB. If iPad is connected to a computer that’s turned off or is in sleep or standby mode, the iPad battery will continue to drain.
Apple recommends that once a month you let the iPad fully discharge & then recharge to 100%.
How to Calibrate Your Mac, iPhone, or iPad Battery
http://www.macblend.com/how-to-calibrate-your-mac-iphone-or-ipad-battery/
At this link http://www.tomshardware.com/reviews/galaxy-tab-android-tablet,3014-11.html , tests show that the iPad 2 battery (25 watt-hours) will charge to 90% in 3 hours 1 minute. It will charge to 100% in 4 hours 2 minutes. The new iPad has a larger capacity battery (42 watt-hours), so using the 10W charger will obviously take longer. If you are using your iPad while charging, it will take even longer. It's best to turn your new iPad OFF and charge over night. Also look at The iPad's charging challenge explained http://www.macworld.com/article/1150356/ipadcharging.html
Also, if you have a 3rd generation iPad, look at
Apple: iPad Battery Nothing to Get Charged Up About
http://allthingsd.com/20120327/apple-ipad-battery-nothing-to-get-charged-up-abou t/
Apple Explains New iPad's Continued Charging Beyond 100% Battery Level
http://www.macrumors.com/2012/03/27/apple-explains-new-ipads-continued-charging- beyond-100-battery-level/
New iPad Takes Much Longer to Charge Than iPad 2
http://www.iphonehacks.com/2012/03/new-ipad-takes-much-longer-to-charge-than-ipa d-2.html
Apple Batteries - iPad http://www.apple.com/batteries/ipad.html
iPhone: Hardware troubleshooting (Power/Battery section also applies to iPad)
http://support.apple.com/kb/TS2802
Extend iPad Battery Life (Look at pjl123 comment)
https://discussions.apple.com/thread/3921324?tstart=30
New iPad Slow to Recharge, Barely Charges During Use
http://www.pcworld.com/article/252326/new_ipad_slow_to_recharge_barely_charges_d uring_use.html
iPad: Charging the battery
http://support.apple.com/kb/HT4060
Best Practices for iPad Battery Charging
http://www.ilounge.com/index.php/articles/comments/best-practices-for-ipad-batte ry-charging/
Tips About Charging for New iPad 3
http://goodscool-electronics.blogspot.com/2012/04/tips-about-charging-for-new-ip ad-3.html
How to Save and Prolong the battery life of your new ipad
https://discussions.apple.com/thread/4480944?tstart=0
Prolong battery lifespan for iPad / iPad 2 / iPad 3: charging tips
http://thehowto.wikidot.com/prolong-battery-lifespan-for-ipad
iPhone, iPod, Using the iPad Charger
http://support.apple.com/kb/HT4327
Install and use Battery Doctor HD
http://itunes.apple.com/tw/app/battery-doctor-hd/id459702901?mt=8
To Extend a Device’s Battery Life, Get to Know It Better
http://tinyurl.com/b67c7xz
iPad Battery Replacement
http://www.apple.com/batteries/replacements.html
In rare instances when using the Camera Connection Kit, you may notice that iPad does not charge after using the Camera Connection Kit. Disconnecting and reconnecting the iPad from the charger will resolve this issue.
 Cheers, Tom 

Similar Messages

  • My Iphone 4 will not charge after Ios7 update, does anyone know how to fix ?, My Iphone 4 will not charge after Ios7 update, does anyone know how to fix ?

    My Iphone 4 will not charge after ipdate to IOS 7.0.4, Does anyone have a solution ? I have tried apple cables and chargers. I see many have the same issue. Anyone made progress ?

    No offence, but as with quite a few others, my Iphone stopped charging on mains after iOS 7.0.4 update too.
    Not sure you can categorically advise that "it simply is not a software issue" when so many different people are having the same symptoms after updating their iOS   Just have a quick Google!
    Luckily my (original Apple) cable will still allow recharging via USB to a laptop. So, process of elimination would point to a bricked charger that was working faultlessly up until the iOS 7.0.4 update was applied. Seems quite a stretch to be a coincidence.
    Look forward to an explanation ..... and an update? ......

  • My iPad will not charge after iOS7

    After I got iOS7, it wouldn't charge at all. I tried charging it in different ways, nothing happened. Previously it has gone dead so when I try and turn it on it asks to be plugged it but it never charges.

    Try resetting it. Hold down the sleep and home keys until you see the silver apple and let it reboot. See if that helps.

  • After downloading ISO8 my USB Ports on my IMAC arnt working and now my iPad2 will not charge?

    after downloading ISO8 my USB Ports on my IMAC arnt working and now my iPad2 will not charge? even tried to use 240v charger? both my iMac and iPad have been updated, my mini iPad is working on old iso7 so that won't be updated in a hurry, any help would be great.

    First is the most USB ports do not provide enough power to charge an iPad. Do not try and charge your iPad from such USB ports.
    There is no 240v charger. There is one charger that will work with US voltages and European voltages. If your iPad is not charger with the charger, make certain that is an iPad charger, not an iPhone charger. If the charger does not work try swapping the cable as the cable may be bad. If that does not work try another charger. All simple steps that should be attempted before pinning the problem on IOS 8.

  • My ipad2 will not charge or start

    what do i do, my ipad2 will not charge or start?

    First make sure that you are using the charger that came with the iPad and have plugged that into a wall outlet. Keep in mind that if the battery is completely drained it make take up to an hour on the charger before the iPad responds. So wait one hour then, while the iPad is still plugged in, reset your device. Press and hold the Home and Sleep buttons simultaneously until the Apple logo appears. Let go of the buttons and let the device restart. If the iPad restarts let it continue to charge until the battery is 100%.
    If the iPad does not start consider these troubleshooting steps.
    1. Bad outlet. Make sure the outlet is providing power.
    2. Bad charger. Try a different charger.
    3. Bad cable. Try a different cable.
    4. Dirt, fuzz, or lint in the connection ports. Check and casually clean if necessary.
    5. Software failure. First thing to try is to reset your device. Press and hold the Home and Sleep buttons simultaneously until the Apple logo appears. Let go of the buttons and let the device restart. See if that fixes your problem.
    6. Hardware failure. Make an appointment at an Apple Store to have your device examined by a technician. Or contact Apple Support.

  • TS1567 my ipad will not open after ios7 installed

    my ipad will not open after ios7 installed

    kerry236 wrote:
    ipad dissabled
    Connect to iTunes on the computer you usually Sync with and Restore
    http://support.apple.com/kb/HT1414
    2)  If necessary Place the Device into Recovery mode...
    http://support.apple.com/kb/ht4097
    Note on Recovery Mode.
    You may need to try this More than Once...
    Be sure to Follow ALL the Steps...
    Once you have Recovered your Device...
    Re-Sync your Content or Restore from the most Recent Backup...
    Restore from Backup
    http://support.apple.com/kb/ht1766
    NOTE:
    Make sure you have the Latest Version of iTunes Installed on your computer ( v 11.1)
    iTunes free download from www.itunes.com/download

  • IPad will not charge after IOS 7 update unless the brightness is dimmed,..Why?

    I recently updated my 4th gen IPad 64Gb to ios7. Previous to the update I loved my iPad and it worked flawlessly. Since updating the iPad now will not charge unless I dim the brightness of the screen, and slowly when it does. Why? Is there a way to remedy this?

    I do not know if it's iOS7 related or not. My 2 is still working. However, my first 2 was returned to best buy after the charging port on it died. So that can happen. ANd it happens with little to no warning. CHarges monday, doesn't on tuesday.
    As far as I know the issues with 'unsigned' lightning devices is just the cable, not the power brick, but there's no official word (nor do I expect one)
    Lightning cables have a little chip in them and if that chip isn't signed by Apple then your device kicks up an error but should still work.
    However since this is an iPad 2, that's not the case since 2's use 30 pin chargers, not lightning.
    Usually when a 2 doesn't charge, common troubleshooting is to swap out the charger, cable and outlet, to confirm or rule those out. Also to do the reset. (the soft reset that's holding down the sleep and home keys until it reboots). Also to look in and blow out the port in case there's some lint or such in there.
    Usually those things fixes it. If not, then it could be the port.

  • The battery in my ipad2 will not charge?

    I let my iPad2 drain its battery - like I´ve sometimes done before.  But now it only shows the battery sign with the red line and then it´s goes blank   What to do??

    The quickest way (and really the only way) to charge your iPad is with the included 10W USB Power Adapter. iPad will also charge, although more slowly, when attached to a computer with a high-power USB port (many recent Mac computers) or with an iPhone Power Adapter (5W). When attached to a computer via a standard USB port (most PCs or older Mac computers) iPad will charge very slowly (but iPad indicates not charging). Make sure your computer is on while charging iPad via USB. If iPad is connected to a computer that’s turned off or is in sleep or standby mode, the iPad battery will continue to drain.
    Apple recommends that once a month you let the iPad fully discharge & then recharge to 100%.
    How to Calibrate Your Mac, iPhone, or iPad Battery
    http://www.macblend.com/how-to-calibrate-your-mac-iphone-or-ipad-battery/
    At this link http://www.tomshardware.com/reviews/galaxy-tab-android-tablet,3014-11.html , tests show that the iPad 2 battery (25 watt-hours) will charge to 90% in 3 hours 1 minute. It will charge to 100% in 4 hours 2 minutes. The new iPad has a larger capacity battery (42 watt-hours), so using the 10W charger will obviously take longer. If you are using your iPad while charging, it will take even longer. It's best to turn your new iPad OFF and charge over night. Also look at The iPad's charging challenge explained http://www.macworld.com/article/1150356/ipadcharging.html
    Also, if you have a 3rd generation iPad, look at
    Apple: iPad Battery Nothing to Get Charged Up About
    http://allthingsd.com/20120327/apple-ipad-battery-nothing-to-get-charged-up-abou t/
    Apple Explains New iPad's Continued Charging Beyond 100% Battery Level
    http://www.macrumors.com/2012/03/27/apple-explains-new-ipads-continued-charging- beyond-100-battery-level/
    New iPad Takes Much Longer to Charge Than iPad 2
    http://www.iphonehacks.com/2012/03/new-ipad-takes-much-longer-to-charge-than-ipa d-2.html
    Apple Batteries - iPad http://www.apple.com/batteries/ipad.html
    Extend iPad Battery Life (Look at pjl123 comment)
    https://discussions.apple.com/thread/3921324?tstart=30
    New iPad Slow to Recharge, Barely Charges During Use
    http://www.pcworld.com/article/252326/new_ipad_slow_to_recharge_barely_charges_d uring_use.html
    Tips About Charging for New iPad 3
    http://goodscool-electronics.blogspot.com/2012/04/tips-about-charging-for-new-ip ad-3.html
    Prolong battery lifespan for iPad / iPad 2 / iPad 3: charging tips
    http://thehowto.wikidot.com/prolong-battery-lifespan-for-ipad
    iPhone, iPod, Using the iPad Charger
    http://support.apple.com/kb/HT4327
    Install and use Battery Doctor HD
    http://itunes.apple.com/tw/app/battery-doctor-hd/id459702901?mt=8
    In rare instances when using the Camera Connection Kit, you may notice that iPad does not charge after using the Camera Connection Kit. Disconnecting and reconnecting the iPad from the charger will resolve this issue.
     Cheers, Tom

  • Iphone 5 will not charge after water damage. Tried various solutions.

    Hi all,
    A few weeks ago i put my iphone 5 in the washing machine for about 30 seconds. I got it out ASAP but it was still noticably wet. I quickly padded it down and put it in a bag of rice for several days (luckily it was already out of battery when it went in).
    After i had left it to dry out i plugged it in only to find the lightining cabel symbol comes up and it will not charge. So what i have done so far;
    Changed battery- new battery still will not charge. However, when i did put a new battery in that held some charge the phone did turn on and everything was working fine.
    Tried new lightning cable
    Changed dock connector- still would not charge
    Removed battery and cleaned entire phone with 99% isopropyl, dried and phone still would not charge.
    I'm pretty lost here??? If everything was working fine when i put the new battery in apart from being able to charge i asssumed it must be the dock connector but apparently not.
    I have heard it might be something to do with the USB/Power IC on the motherboard?? But im not sure if these can be replaced. I would just like to try everything myself before taking to apple as i know they will charge me a small fortune for out of warrenty repair.

    yiddonick wrote:
    So your telling me as soon as i open the phone the out of warrenty service is void as well (even if i were to put the old battery back in)?
    Yes.
    Is their an indicator to show the phone has been opened?
    Yes. There are tamper indicators inside the phone.
    People should have the right to change their battery or open their phone if they want instead of being forced to make a genius bar appointment for any type of service (apple stores are few and far between where i live).
    You do have that right. But if you choose to exercise it, you forfeit your right to an out of warranty replacement.
    Note: I took it to a repair shop re dock connector change. They changed it and it wouldnt work so they replaced old one and said apple wouldnt have a problem fixing it on the out of warrenty repair service.
    They lied to you.
    If the service is void i certainly will not be buying another iphone. I guess this is how apple make their money.
    Go ahead. Try the same thing with another vendor... let us know how that works for you.

  • TA44551 my i pod classic will play works great! in a dock but will not charge ( after new battery ) HELP !!!

    I have an older Ipod classic it plays on everything i have . Recently replaced the battery because it would not take charg .After new battery it plays through several defferent devices but it will not CHARG !!!    HELP!!!!

    Not Charge
    - See:      
    iPod touch: Hardware troubleshooting
    - Try another cable. Some 5G iPods were shipped with Lightning cable that were either initially defective or failed after short use.
    - Try another charging source
    - Inspect the dock connector on the iPod for bent or missing contacts, foreign material, corroded contacts, broken, missing or cracked plastic.
    - Make an appointment at the Genius Bar of an Apple store.
    Apple Retail Store - Genius Bar                          
    Also:
    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try on another computer          
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar       

  • Ipad2 will not charge

    I have tried several chargers and my iPhone charges but the IPad will not charge. The home button does not work either.

    Try a reset. Hold the Sleep and Home button down for about 10 seconds until you see the Apple logo. Ignore the red slider.
    The defective Home may not allow you to do a reset.

  • Mid 2010 Macbook Pro battery will not charge after plugging in firewire cable shut down computer

    I have a mid 2010 15" Macbook pro with Lion installed.
    I was running off battery, and I went to plug in a firewire cable, not plugged into anything, and when I inserted it, the computer shut off.
    The computer would not turn on again without being plugged into the AC adaptor. The magsafe charger shows green, but the computer says not charging. The battery is showing 57%, but the indicator lights will only light up when AC charger is connected..
    I have let it sit off, and plugged in for a couple hours, and nothing chages, and let it sit overnight not plugged in, but nothing.
    I have read other forums about the same issue,, it seems like its a common issue, and some have said what it could be, but no one said what it IS.
    I have tried resetting the SMC and PRAM, but to no avail.
    When i plug in the AC adaptor, the computer immediately turns on (which I find kond of funny), and I am able to turn it off normally, and it will stay off, and I can also turn it on if the charger has been connected from pervious.
    Below is my power information.:
    Battery Information:
      Model Information:
      Serial Number:          W0013PVDXBX0A
      Manufacturer:          SMP
      Device Name:          bq20z451
      Pack Lot Code:          0
      PCB Lot Code:          0
      Firmware Version:          201
      Hardware Revision:          000a
      Cell Revision:          157
      Charge Information:
      Charge Remaining (mAh):          3406
      Fully Charged:          No
      Charging:          No
      Full Charge Capacity (mAh):          5956
      Health Information:
      Cycle Count:          395
      Condition:          Normal
      Battery Installed:          Yes
      Amperage (mA):          0
      Voltage (mV):          11638
    System Power Settings:
      AC Power:
      System Sleep Timer (Minutes):          0
      Disk Sleep Timer (Minutes):          0
      Display Sleep Timer (Minutes):          5
      Wake on AC Change:          No
      Wake on Clamshell Open:          Yes
      Wake on LAN:          Yes
      Current Power Source:          Yes
      Display Sleep Uses Dim:          Yes
      PrioritizeNetworkReachabilityOverSleep:          0
      RestartAfterKernelPanic:          157680000
      Battery Power:
      System Sleep Timer (Minutes):          0
      Disk Sleep Timer (Minutes):          0
      Display Sleep Timer (Minutes):          3
      Wake on AC Change:          No
      Wake on Clamshell Open:          Yes
      Display Sleep Uses Dim:          Yes
      Reduce Brightness:          Yes
      RestartAfterKernelPanic:          157680000
    Hardware Configuration:
      UPS Installed:          No
    AC Charger Information:
      Connected:          Yes
      ID:          0x0100
      Wattage (W):          85
      Revision:          0x0000
      Family:          0x00ba
      Serial Number:          0x00b9468c
      Charging:          No
    Any help would be greatly appreciated. Thanks everyone.

    I have a mid 2010 15" Macbook pro with Lion installed.
    I was running off battery, and I went to plug in a firewire cable, not plugged into anything, and when I inserted it, the computer shut off.
    The computer would not turn on again without being plugged into the AC adaptor. The magsafe charger shows green, but the computer says not charging. The battery is showing 57%, but the indicator lights will only light up when AC charger is connected..
    I have let it sit off, and plugged in for a couple hours, and nothing chages, and let it sit overnight not plugged in, but nothing.
    I have read other forums about the same issue,, it seems like its a common issue, and some have said what it could be, but no one said what it IS.
    I have tried resetting the SMC and PRAM, but to no avail.
    When i plug in the AC adaptor, the computer immediately turns on (which I find kond of funny), and I am able to turn it off normally, and it will stay off, and I can also turn it on if the charger has been connected from pervious.
    Below is my power information.:
    Battery Information:
      Model Information:
      Serial Number:          W0013PVDXBX0A
      Manufacturer:          SMP
      Device Name:          bq20z451
      Pack Lot Code:          0
      PCB Lot Code:          0
      Firmware Version:          201
      Hardware Revision:          000a
      Cell Revision:          157
      Charge Information:
      Charge Remaining (mAh):          3406
      Fully Charged:          No
      Charging:          No
      Full Charge Capacity (mAh):          5956
      Health Information:
      Cycle Count:          395
      Condition:          Normal
      Battery Installed:          Yes
      Amperage (mA):          0
      Voltage (mV):          11638
    System Power Settings:
      AC Power:
      System Sleep Timer (Minutes):          0
      Disk Sleep Timer (Minutes):          0
      Display Sleep Timer (Minutes):          5
      Wake on AC Change:          No
      Wake on Clamshell Open:          Yes
      Wake on LAN:          Yes
      Current Power Source:          Yes
      Display Sleep Uses Dim:          Yes
      PrioritizeNetworkReachabilityOverSleep:          0
      RestartAfterKernelPanic:          157680000
      Battery Power:
      System Sleep Timer (Minutes):          0
      Disk Sleep Timer (Minutes):          0
      Display Sleep Timer (Minutes):          3
      Wake on AC Change:          No
      Wake on Clamshell Open:          Yes
      Display Sleep Uses Dim:          Yes
      Reduce Brightness:          Yes
      RestartAfterKernelPanic:          157680000
    Hardware Configuration:
      UPS Installed:          No
    AC Charger Information:
      Connected:          Yes
      ID:          0x0100
      Wattage (W):          85
      Revision:          0x0000
      Family:          0x00ba
      Serial Number:          0x00b9468c
      Charging:          No
    Any help would be greatly appreciated. Thanks everyone.

  • Iphone 5 will not activate after iOS7 update.

    Ive tried over the air and through iTunes, no luck either way. Says the servers cannot be contacted.
    Is there a number I can call to activate this another way?

    Apple's activation servers are probably very busy. Calling AppleCare will not really help as the servers are what allow that to happen. You may want to wait for a little while before trying again.

  • IPad will not restore after iOS7 update

    I just updated my iPad to ios7, did restart and restore and now I cannot get past the welcome screen.  It keeps asking me to restore from backup, which I have done repeatedly.  My computer shows my iPad as having everything restored, but the iPad does not.  HELP!!!!!

    Restore from iTune Backup
    1. Settings>General>Reset>Erase all content and settings
    2. You'll be asked twice to confirm
    3. You'll see Apple logo and progress bar
    4. You'll see a big iPad logo on screen
    5. Configuration start
    6. Set language
    7. Set country
    8. Select Network and input Password>Join
    9. Enable Location Service>Next
    10. You'll be given 3 options (a) Setup as New iPad (b) Restore from iCloud Backup (c) Restore from iTune Backup
    11. Select Restore from iTune Backup
    12. You will see picture of USB cable pointing towards iPad
    13. Connect iPad to iTune (make sure iTune is on standby)
    14. Tap Continue (computer)
    15. Restore iPad from Backup (computer)
    16. See progress bar with estimated time (computer)
    17. See Restore in Progress on iPad
    18. See Apple logo
    19. See Apple and Progress Bar
    20. Slide to Unlock
    21. Copying Apps back to iPad (computer)
    22. You'll see Loading/Installing/Waiting below the Apps (iPad)
    23. Sync Music/Podcast/Movies to iPad (computer)
    24. Sync completed (computer)

  • IPAD2 will not start after set to flight mode.

    I set my IPAD2 in flightmode.6 hours later, i try to activate it again. It just shows a blanc screen. I hold the off button in and turn of the IPAD2. I try to restart it, and now 4 hours later, it is still "starting up". The "wheel" is turning, but nothing happens? What can i do?????

    Mine had a similar thing happen after a few weeks, except that mine wouldn't even start until I'd done the reset - I havn't had a problem since. Unless you start getting regular problems I wouldn't get too concerned. And it may have been caused by apps that you've downloaded, so it may not necessarily be down to the operating system or Apple's apps - but no code is bug free.

Maybe you are looking for

  • Upload Attachments

    Hi Gurus, I have a requirement where client is migrating from People Soft to CRM 7.0. There is a data conversion happening and we need to migrate attachments for Cases. There is a Content Server which is installed at CRM end which will handle new att

  • Queue not queueing

    I have a producer / consumer architecture - data are being read (from a TCP read) in the producer loop and placed on a queue. The consumer is reading the queue and doing lots of modelling, analysis and display. This architecture was chosen because th

  • Map a function key to ctrl-z

    I'm looking for a way to get a function key (such as F12) to produce a ctrl-z combination. Can't find a way to do this, xmodmap wont map to combinations, xkb configuration seems waaayyy complicated. Is there something simpler?

  • Troubleshooting packages with PCM after migration

    In my lab i've migrated to cm 2012 and installed PCM, however the majority of my packages have a readiness state of "the directory name is invalid" The source files are .exe's. SCCM 2012 RC with PCM SP1 from the PCMTrace.log Microsoft.ConfigurationMa

  • Handling Submit Button on the ADOBE form called from Web Dynpro

    Hi, I have placed a Button on the ADOBE Form. How to Handle the event on this button. When i click this button, i want to save the details of the form into a Custom table.