Ipad2 will not charge

I have tried several chargers and my iPhone charges but the IPad will not charge. The home button does not work either.

Try a reset. Hold the Sleep and Home button down for about 10 seconds until you see the Apple logo. Ignore the red slider.
The defective Home may not allow you to do a reset.

Similar Messages

  • After downloading ISO8 my USB Ports on my IMAC arnt working and now my iPad2 will not charge?

    after downloading ISO8 my USB Ports on my IMAC arnt working and now my iPad2 will not charge? even tried to use 240v charger? both my iMac and iPad have been updated, my mini iPad is working on old iso7 so that won't be updated in a hurry, any help would be great.

    First is the most USB ports do not provide enough power to charge an iPad. Do not try and charge your iPad from such USB ports.
    There is no 240v charger. There is one charger that will work with US voltages and European voltages. If your iPad is not charger with the charger, make certain that is an iPad charger, not an iPhone charger. If the charger does not work try swapping the cable as the cable may be bad. If that does not work try another charger. All simple steps that should be attempted before pinning the problem on IOS 8.

  • My ipad2 will not charge or start

    what do i do, my ipad2 will not charge or start?

    First make sure that you are using the charger that came with the iPad and have plugged that into a wall outlet. Keep in mind that if the battery is completely drained it make take up to an hour on the charger before the iPad responds. So wait one hour then, while the iPad is still plugged in, reset your device. Press and hold the Home and Sleep buttons simultaneously until the Apple logo appears. Let go of the buttons and let the device restart. If the iPad restarts let it continue to charge until the battery is 100%.
    If the iPad does not start consider these troubleshooting steps.
    1. Bad outlet. Make sure the outlet is providing power.
    2. Bad charger. Try a different charger.
    3. Bad cable. Try a different cable.
    4. Dirt, fuzz, or lint in the connection ports. Check and casually clean if necessary.
    5. Software failure. First thing to try is to reset your device. Press and hold the Home and Sleep buttons simultaneously until the Apple logo appears. Let go of the buttons and let the device restart. See if that fixes your problem.
    6. Hardware failure. Make an appointment at an Apple Store to have your device examined by a technician. Or contact Apple Support.

  • The battery in my ipad2 will not charge?

    I let my iPad2 drain its battery - like I´ve sometimes done before.  But now it only shows the battery sign with the red line and then it´s goes blank   What to do??

    The quickest way (and really the only way) to charge your iPad is with the included 10W USB Power Adapter. iPad will also charge, although more slowly, when attached to a computer with a high-power USB port (many recent Mac computers) or with an iPhone Power Adapter (5W). When attached to a computer via a standard USB port (most PCs or older Mac computers) iPad will charge very slowly (but iPad indicates not charging). Make sure your computer is on while charging iPad via USB. If iPad is connected to a computer that’s turned off or is in sleep or standby mode, the iPad battery will continue to drain.
    Apple recommends that once a month you let the iPad fully discharge & then recharge to 100%.
    How to Calibrate Your Mac, iPhone, or iPad Battery
    http://www.macblend.com/how-to-calibrate-your-mac-iphone-or-ipad-battery/
    At this link http://www.tomshardware.com/reviews/galaxy-tab-android-tablet,3014-11.html , tests show that the iPad 2 battery (25 watt-hours) will charge to 90% in 3 hours 1 minute. It will charge to 100% in 4 hours 2 minutes. The new iPad has a larger capacity battery (42 watt-hours), so using the 10W charger will obviously take longer. If you are using your iPad while charging, it will take even longer. It's best to turn your new iPad OFF and charge over night. Also look at The iPad's charging challenge explained http://www.macworld.com/article/1150356/ipadcharging.html
    Also, if you have a 3rd generation iPad, look at
    Apple: iPad Battery Nothing to Get Charged Up About
    http://allthingsd.com/20120327/apple-ipad-battery-nothing-to-get-charged-up-abou t/
    Apple Explains New iPad's Continued Charging Beyond 100% Battery Level
    http://www.macrumors.com/2012/03/27/apple-explains-new-ipads-continued-charging- beyond-100-battery-level/
    New iPad Takes Much Longer to Charge Than iPad 2
    http://www.iphonehacks.com/2012/03/new-ipad-takes-much-longer-to-charge-than-ipa d-2.html
    Apple Batteries - iPad http://www.apple.com/batteries/ipad.html
    Extend iPad Battery Life (Look at pjl123 comment)
    https://discussions.apple.com/thread/3921324?tstart=30
    New iPad Slow to Recharge, Barely Charges During Use
    http://www.pcworld.com/article/252326/new_ipad_slow_to_recharge_barely_charges_d uring_use.html
    Tips About Charging for New iPad 3
    http://goodscool-electronics.blogspot.com/2012/04/tips-about-charging-for-new-ip ad-3.html
    Prolong battery lifespan for iPad / iPad 2 / iPad 3: charging tips
    http://thehowto.wikidot.com/prolong-battery-lifespan-for-ipad
    iPhone, iPod, Using the iPad Charger
    http://support.apple.com/kb/HT4327
    Install and use Battery Doctor HD
    http://itunes.apple.com/tw/app/battery-doctor-hd/id459702901?mt=8
    In rare instances when using the Camera Connection Kit, you may notice that iPad does not charge after using the Camera Connection Kit. Disconnecting and reconnecting the iPad from the charger will resolve this issue.
     Cheers, Tom

  • Ipad2 will not charge after ios7

    Tried reset many times.  Tried several apple cords.

    Try this first - Reset the iPad by holding down on the Sleep and Home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons. (This is equivalent to rebooting your computer.)
    The quickest way (and really the only way) to charge your iPad is with the included 10W or 12W (5W on Mini) USB Power Adapter. iPad will also charge, although more slowly, when attached to a computer with a high-power USB port (many recent Mac computers) or with an iPhone Power Adapter (5W). When attached to a computer via a standard USB port (2.5W, most PCs or older Mac computers) iPad will charge very slowly (but iPad indicates not charging). Make sure your computer is on while charging iPad via USB. If iPad is connected to a computer that’s turned off or is in sleep or standby mode, the iPad battery will continue to drain.
    Apple recommends that once a month you let the iPad fully discharge & then recharge to 100%.
    How to Calibrate Your Mac, iPhone, or iPad Battery
    http://www.macblend.com/how-to-calibrate-your-mac-iphone-or-ipad-battery/
    At this link http://www.tomshardware.com/reviews/galaxy-tab-android-tablet,3014-11.html , tests show that the iPad 2 battery (25 watt-hours) will charge to 90% in 3 hours 1 minute. It will charge to 100% in 4 hours 2 minutes. The new iPad has a larger capacity battery (42 watt-hours), so using the 10W charger will obviously take longer. If you are using your iPad while charging, it will take even longer. It's best to turn your new iPad OFF and charge over night. Also look at The iPad's charging challenge explained http://www.macworld.com/article/1150356/ipadcharging.html
    Also, if you have a 3rd generation iPad, look at
    Apple: iPad Battery Nothing to Get Charged Up About
    http://allthingsd.com/20120327/apple-ipad-battery-nothing-to-get-charged-up-abou t/
    Apple Explains New iPad's Continued Charging Beyond 100% Battery Level
    http://www.macrumors.com/2012/03/27/apple-explains-new-ipads-continued-charging- beyond-100-battery-level/
    New iPad Takes Much Longer to Charge Than iPad 2
    http://www.iphonehacks.com/2012/03/new-ipad-takes-much-longer-to-charge-than-ipa d-2.html
    Apple Batteries - iPad http://www.apple.com/batteries/ipad.html
    iPhone: Hardware troubleshooting (Power/Battery section also applies to iPad)
    http://support.apple.com/kb/TS2802
    Extend iPad Battery Life (Look at pjl123 comment)
    https://discussions.apple.com/thread/3921324?tstart=30
    New iPad Slow to Recharge, Barely Charges During Use
    http://www.pcworld.com/article/252326/new_ipad_slow_to_recharge_barely_charges_d uring_use.html
    iPad: Charging the battery
    http://support.apple.com/kb/HT4060
    Best Practices for iPad Battery Charging
    http://www.ilounge.com/index.php/articles/comments/best-practices-for-ipad-batte ry-charging/
    Tips About Charging for New iPad 3
    http://goodscool-electronics.blogspot.com/2012/04/tips-about-charging-for-new-ip ad-3.html
    How to Save and Prolong the battery life of your new ipad
    https://discussions.apple.com/thread/4480944?tstart=0
    Prolong battery lifespan for iPad / iPad 2 / iPad 3: charging tips
    http://thehowto.wikidot.com/prolong-battery-lifespan-for-ipad
    iPhone, iPod, Using the iPad Charger
    http://support.apple.com/kb/HT4327
    Install and use Battery Doctor HD
    http://itunes.apple.com/tw/app/battery-doctor-hd/id459702901?mt=8
    To Extend a Device’s Battery Life, Get to Know It Better
    http://tinyurl.com/b67c7xz
    iPad Battery Replacement
    http://www.apple.com/batteries/replacements.html
    In rare instances when using the Camera Connection Kit, you may notice that iPad does not charge after using the Camera Connection Kit. Disconnecting and reconnecting the iPad from the charger will resolve this issue.
     Cheers, Tom 

  • My ipad2 will not charge, switch on or connect to itunes is there any way i can do a restore or will this not help anyway?

    is there any way i can over ride this?

    You can try to place the iPad into recovery mode and see if it will restore. I don't know of anything else that you could try if the iPad is totally unresponsive.
    I would let it charge for a while first - even if you have tried to let it charge already. This article explains recovery mode.
    iPad: Unable to update or restore

  • My ipad2 will not charge or turn on, how do i fix it

    i used 2 different cables, tried usb to pc and 110 with both, tested outlets and usb ports for power, all good, I am stuck, how do i fix it?
    thanks in advance for responding

    Have you tried a soft-reset (i.e. reboot) to see if that gets it to boot up ? Press and hold both the sleep and home buttons for about 10 to 15 seconds, after which the Apple logo will hopefully appear.

  • My iPad2 will not charge...

    The iPad is out of battery, and when I plug in the charger (mains) it doesn't even recognise that the charger has been connected.
    I have had this issue intermittently for a month or so.
    I have replaced the USB lead a couple of weeks ago, this als makes no difference...
    I have attempted a full reset, but this makes no difference at all...
    Any Ideas??

    Common?  No.  Possible?  Yes.  I would think that the likely problem is damage at the connector port due to stress incurred due to plugging and unplugging.  Related to that could be the cables have failed.  Those two things could be identified at the genius bar.  As far as the warranty being gone, they still can offer to replace the device for the out of warranty repair fee, which should be significantly less than buying a new device.  Of course if you are on an iPad 2, You would probably be happier (if poorer) shifting to an iPad 4, or an iPad Air with more memory, and a warranty that you could extend by purchasing applecare.
    Best of luck.

  • My ipad2 is not charging. Can I access my mail through my desktop?

    My newish ipad2 will not charge. I've checked the socket and charger on my son's iphone and they are fine. I just get a black screen, if I click the home button I get a battery icon with red top for 5 seconds, then black screen again.  Can I access my icloud and emails through my windows desktop?

    To know if it's really charging or not, note the percentage, plug it into your PC for an hour and then unplug it and check the percentage again.
    Another thing to note, most USB ports only charge if the PC is on. (even macs to be honest) so to charge through your comptuer you have to leave the computer on. In some cases, letting it go to sleep will even stop the charging. The supplied power brick is honestly the best and fastest way to charge your iPad.

  • I was updating my Ipad2 and when it was done it went to the apple logo and wont leave that screen it also will not charge

    I was updating my Ipad2 and when it was done it went to the apple logo and wont leave that screen it also will not charge. Ive tried resetting and it turns off for a second then come right back to the Apple screen.

    Try and force iPad into Recovery Mode:
    1. Turn off iPad. Press and hold the Sleep/Wake button for a few seconds until the red slider appears, slide to turn off.
    2. Connect USB cable to computer; leave the other end alone
    3. Press and hold the Home button down and connect the docking end of cable to iPad
    4. Continue holding the Home button until you see the "Connect To iTune" screen
    5. Release the Home button
    6. Open iTune (make sure you have the newest version of iTune)
    7. You should see "iTunes has detected an iPad in recovery mode"
    8. Use iTune to restore iPad
    Note: You need to be patient and repeat the above many times to recover your iPad

  • Ipad2 will not start ,just dead.battery is charged

    Ipad2 will not start ,just dead.battery is charged

    Mine had a similar thing happen after a few weeks, except that mine wouldn't even start until I'd done the reset - I havn't had a problem since. Unless you start getting regular problems I wouldn't get too concerned. And it may have been caused by apps that you've downloaded, so it may not necessarily be down to the operating system or Apple's apps - but no code is bug free.

  • Can anyone help me plz.  My ipad will not charge.  I am using the cords that came with it and it still wont charge

    Can anyone please help me.  I have had my ipad2 for about 5 months and it has worked fine.  I am now having issues charging it.  I am using the cords that came with it and the outlet that I have used to charge it in the past, but when plugged in it is recconoigzed, but states not charging.  I have made sure all my updates are current and they are.  Does anyone have any suggestions or helful advice that my help.  Thanks in advance.

    Are you plugging it into a pc? If so it will not charge the iPad as there is not enough power try the back USB ports, may work.
    If it isn't plugged into a pc and plugged into your socket could be faulty socket adapter.

  • Battery will not charge. and other issues

    Well i'm working on a friend of mines notebook, its a n100 model 0768 12u running windows xp. This is the situation so far. First his hard drive had fried so i replaced that and put the o.s. back on it,but now the battery will not charge. also the wireless network card and dvd drive did not work. I had originally thought that they might have fried as well when the hard drive went down. However I looked through the forums here and found that alot of people solved the battery issue simply by replacing the battery i recommended that. He purchased a replacement battery ( not a genuine lenovo battery, don't know if that makes a difference) and when i put it in the dvd drive and the network card started working no problem. But alas the battery still would not charge. the system runs fine without a battery in it, but if i put the battery in it while its running it turns itself off after about 30 seconds of having the battery in. when the system is powered off and i put the battery in the battery lcd in front blinks 5 times orange then nothing for about 30 seconds then 5 more times. maybe thats a trouble code, don't know, looked all oover the forums and couldn't find anything quite like it. any help would be greatly appreciated.
     thanks
    Steve

    Duck3,
    Glad that worked for you!  Thanks for sharing here. 
    I saw a weird situation on friend's ThinkPad recently - a replacement battery arrived with a 37% charge (not 100% deliberately as somewhere around 40% is the best for shelf life), but it would not accept a charge.   We did a reset by removing the battery & AC and pressing and holding the power button a number of times  (some people say 10 times, some two or three times for a count of 5 or 10).   This drains residual capacitance.
    We plugged back in the battery and AC and it began to charge.  
    Might be worth a try here before he opens it up ....
    ThinkPads: S30, T43, X60t, X1, W700ds, IdeaPad Y710, IdeaCentre: A300, IdeaPad K1
    Mark Hopkins
    Program Manager, Lenovo Social Media (Services)
    twitter @lenovoforums
    English Community   Deutsche Community   Comunidad en Español   Русскоязычное Сообщество

  • Palm Pre crazy symptoms: "phone offline", will not charge battery, will not start, error message "an error has occured that cannot be resolved"

    This is a long description of a series of problems with my new Palm Pre. You may wish to search the text to find your specific issue(s). There is no solution in my post. Look for possible answers in the responses to come.
    I bought my Palm Pre 4 days ago and it arrived 2 days ago. Phone worked great. Last night I plugged in the phone and updated the OS. After completion, I selected "Done" and went to bed.
    - First Series of Issues: "Phone Offline", will not charge battery -
    In upper lefthand corner of the phone there is the message "phone offline". Although the phone has been charging all night it reads "26% battery". I called the general Sprint tech support number and we tried the following things:
    1) Restart phone (press and hold power button, then select "turn off". after power down, press and hold power button to power on.)
    2) Reset the phone (several different ways - call tech support so that you do this correctly)
    The individual at Sprint then sent me to another tech support person, presumably 2nd tier.
    - Second Series of Issues: Error message "an error has occured that cannot be resolved" -
    Sprint tech support person #2 also had me restart and reset the phone in a number of ways. In her words "we've tried every palm pre trick I know" and each time the phone was unresponsive. Often we received the error message "phone is offline". We did a full erase and after that the phone would no longer restart. At this point the error message came up saying "an error has occured that cannot be resolved" which referred me to www.palm.com for assistance. I think it's important to note here that this was not the typical error message (black screen with white letters) but rather the blue sky background with a semitransparent box over it with white text.
    Sprint tech support person #2 then connected me with Palm support and the dance continued. Again we tried a whole bunch of resetting and restarting and erasing options. Palm support instructed me to go to: www.palm.com/rom to download WebOS Doctor, which I did. I downloaded the file. While that was happening he had me hold the "volume up" button and plug the phone into the charger. This caused a USB symbol to appear on the phone. When the file was complete I received an error message that the file couldn't run. Palm tech support person seemed surprised. I mentioned that I was on a Mac and he said he couldn't help me. He then transferred me to another Palm support person who works with Mac users.
    Palms tech support person #2 then informed me that I should have selected the "mac" download option on www.palm.com/rom. I verbally walked her through the whole series of webpages, telling her that it says that you need Windows (version whatever) or Mac (version whatever) but that at no time was there an option to download a different WebOS Doctor for different operating systems. After some more discussion she told me she would have to have someone call me back tomorrow.
    - Third Series of Issues: phone stuck on USB symbol -
    So at the moment the phone is completely useless. Not fantastic. I booted up the mac in Windows 7 and downloaded WebOS Doc and received the same error. I also ran Windows Vista virtually and received the same error. Later this afternoon I'm heading into work to try the same thing on Windows XP.
    In the meantime, I got onto this forum and located a thread that provided a direct link to the necessary file:
    palm.cdnetworks.net/staging/rom/webosdoctorp100ewwsprint.jar
     After downloading that file, which I realized could totally be a virus, I was able to get WebOS Doc working on my computer. It required that I recharge the phone completely before beginning and now it's on the screen that says "Don't disconnect your phone" and the file is at 3% complete. Only... it's been at 3% complete for almost 30 minutes.
    I am hoping that Palm will follow up with me tomorrow, but I'm leaving at 7am on a business trip and would love to have the thing working. Any suggestions are welcome, even if you can just tell me how to get the think disconnected safely before my flight tomorrow. I don't fancy getting through security with my phone wired to my laptop.
    Thanks.
    Post relates to: Pre p100eww (Sprint)
    This question was solved.
    View Solution.

    Hello and welcome to the forums;
    Our phone support is open every day Monday through Sunday, although there are different hours of operation for the weekend. If after a webOS Doctor reset you are still experiencing the same problems, I would likely recommend replacement, either in a local store for your carrier or through our technical support department.
    There may be additional technical support offered or suggested over the phone, this would need to be done first before a replacement could be issued.
    Hope this helps,
    TreoAide

  • My ipod will not charge from a wall socket but will charge using the same cable if the usb end is plugged into a computer or an airport power source. My iphone and ipad charge fine on the same cable usin ghte same wall plug in the same wall socket?

    My ipod will not charge from a wall socket but will charge using the same cable if the usb end is plugged into a computer or directly into an airport power source. My iphone and ipad charge fine on the same cable using the same wall plug in the same wall socket. This makes no sense but I see that it has been posted as a problem elsewhere. This must be due to some kind of degredation of the Ipod. . It is not fixed by IOS resets as others have noted.
    Has anyone asked Apple directly about this?

    Hi there Apples or Pears,
    I would recommend taking a look at the troubleshooting steps found in the articles below.
    Charging your iPod battery
    http://support.apple.com/kb/ht1384
    iPod's battery doesn't charge
    http://support.apple.com/kb/ta44551
    -Griff W.

Maybe you are looking for

  • I have a I-MAC and have used firefox, but lately it will not open from the dock, any suggestions?

    As stated above, have used Firefox from the dock for quite a long time, but recently it did not do anything when I clicked on it, just sat there. Have been able to get to it using spotlight, but even then have to go thru extra steps and go thru a ste

  • MB1C Upload Program Coding Block Screen

    Dear Experts,                    I have created an upload recording of mb1c transaction. After adding header data I have created it's classification entries. Recording has been created successfully. But; when I execute this recording to upload tab-de

  • Stopping and starting database in 10G OEM

    Hello, has anyone run into an issue trying to stop and then start a database within the OEM console in 10G? We are able to stop and start the db with sql and windows services. We can stop the db in OEM but can't start it.

  • Where is a downloaded PDF form?

    I've tried many times to download my PDF form but everytime I do I can't find it. I get the bar saying it's exporting, and then downloading the form but then nothing. Have searched my entire computer but it's nowhere to be found! Any ideas? Thanks

  • Google-earth launch error

    Hi, I have installed latest package google-earth from the AUR, but when I load google-earth get this error message: /usr/bin/google-earth: line 46: ./googleearth-bin: No such file or directory Does anybody know a solution? Thnx!