IPad3 broken or hacked?

Ipad 3 suddenly starts up every app and types in unknown data within seconds, then flashes on to the all other apps including Safari and sites I have visited. When I try to close any app there is not enough time. Could it be a bad sim card or some kind of outside hack? Bought the ipad 3 directly thru Apple and never had any problems before. MacBook Air and Iphone are all running fine. Obviousy, tried turning off and on, charging, etc. and it continues to happen so I am just leaving it turned off for now. Any ideas are appreciated.

This is not a hack. My guess would be a hardware problem, but try some basic troubleshooting first.
First, try resetting your device. Press and hold both the home button and the sleep/wake button for about 10 seconds, until the screen turns off. Ignore the slider that will appear. Release the buttons, then press and hold the sleep/wake button until the Apple logo appears. This is the equivalent of a reboot, and should not affect your data or apps.
If that doesn't help, try restoring your device from backups, and if that doesn't help, restore it to factory settings (ie, do not restore a backup). See:
http://support.apple.com/kb/ht1414
If none of that helps, the issue is caused by some kind of hardware problem, and the device will need to be repaired or (more likely) replaced.

Similar Messages

My AppStore is broken or hacked

Please help me someone I go on App Store and says can't connect to App Store the wifi is fully functional and on and when I go on Game Center it says when I try download an app off it connot download app because connected to server pretending to be iTunes.apple.com

When troubleshooting iTunes Store connection issues, the following articles provide the best information:
First, try signing out of your account in Settings > iTunes & App Store. Once signed out, go ahead and sign back in.
iOS: Changing the signed-in iTunes Store Apple ID account
http://support.apple.com/kb/HT1311
If the above did not resolve your issue, refer to the following:
Can't connect to the iTunes Store
http://support.apple.com/kb/TS1368
If you haven't been able to connect to the iTunes Store:
- Make sure that your iOS software is up to date by connecting your iOS device to iTunes and clicking on Check for Update in your device's Summary page in iTunes.
- Check and verify that you are in range of a Wi-Fi router or base station. If you are on a 3G capable device, make sure that cellular data is turned on from Settings > General > Cellular.
- Check to make sure you have an active internet connection. You can check the User Guide for your device for help with connecting to the internet.
- Check to make sure other devices (portable computers, for example) are able to connect to the Wi-Fi network and access the internet.
- Try resetting (turning off and then on again) your Wi-Fi router
- If the issue still persists see, iOS: Troubleshooting Wi-Fi networks and connections or iOS: Troubleshooting Wi-Fi networks and connections.
Thanks,
Matt M.

App scam in progress or hacked developer account

Hi all,
How do I report a scam in the App Store? Or it could be that an iTunes developer account was broken or hacked into. The app called "A True Level" has been priced around $2 for 90+ days. According to AppSniper, the app is on "sale" for $20 down from $100. in the iTunes App Store the price is currently $19.99. Either the developer is trying to pull a scan or their account has hacked into.
I do now see were to report a concern unless the app has been purchased. I'm trying to stop someone from getting ripped off. Hopefully, I've put enough buzzwords in this message to catch the eye of the forum moderators.
Thanks!
Steven

If you believe that the app is or has been mispriced, you should contact the developer:
http://www.hamwayapps.com//Tip_Jar_%26_Truelevel.html
They can contact the App Store and work out the problem, if one exists. Note that they appear to have two versions, the full version and a "free" version which used to cost $2.99 but was dropped to free back in November, from what I've read. So there may be no "scam" going on, just some confusion between the now-free and paid versions.

Replacing a broken screen

Hello, please how would i replace my ipad3 broken screen

Apple's Limited Warranty http://www.apple.com/legal/warranty/ for iPad excludes coverage for damage resulting from accident, disassembly, unauthorized service and unauthorized modifications.
Out-of-Warranty Service
If you own an iPad that is ineligible for warranty service but is eligible for Out-of-Warranty (OOW) Service, Apple will replace (Apple doesn't repair) your iPad with an iPad that is new or equivalent to new in both performance and reliability for the Out-of-Warranty Service fee listed below. (The replacement will most likely be a refurbished iPad in a brown box, however, it has a new screen, back and battery.)
iPad model
Out-of-Warranty Service Fee
iPad mini
$219
iPad 3rd, 4th generation
$299
iPad 2, iPad
$249
A $6.95 shipping fee will be added if service is arranged through Apple and requires shipping. All fees are in US dollars and are subject to local tax.
Certain damage is ineligible for out-of-warranty service, including catastrophic damage, such as the device separating into multiple pieces, and inoperability caused by unauthorized modifications. However, an iPad that has failed due to contact with liquid may be eligible for out-of-warranty service. See http://support.apple.com/kb/index?page=servicefaq&geo=United_States&product=ipad
Make a Genius Bar Reservation
http://www.apple.com/retail/geniusbar/
You may can get the iPad repaired at 3rd party repair sources for less $, however, any remaining Apple warranty will be voided.
iCracked - Broken iPhone, iPod or iPad
http://www.icracked.com/
iReVamp Electronics Screen Repair ($99)
http://www.irevampelectronics.com/ipad-2-broken-glass-screen-repair.html
iPad Repair & Screen Replacement Services
http://www.ifixyouri.com/16-ipad-repairs
RepairZoom iPad Repair
http://www.repairzoom.com/ipad-repair.html
Mission Repair
http://www.missionrepair.com/Apple_iPad_Repair_Services_s/431.htm
iGadgetResQ
http://www.igadgetresq.com/ipad-repair/
Do It Yourself iPad Repair
http://www.ifixit.com/Device/iPad
 Cheers, Tom

HT4623 my iphone is not activating. why?

i have updated my iphone but now it isnt activating why?

Generally the sign of an iPhone that's been jail broken or hacked.

IPad AppStore not downloading apps

For some reason i was downloading free apps on my ipad just fine a few minutes ago and now the App Store wont download any new apps! It downloads recent apps just fine but when i tap the free button on the app i want and put in my password it says waiting for a few seconds and then it says free again and doesn't download the app. the iOS is updated to the most recent version, I'm only using half of the system memory, my wifi is fine, I've tried logging in and out of my account, switched off iCloud, rebooted the iPad, and still it won't download new apps. My ipad isn't jail broken or hacked and I'm not going to set it back to factory setting because 1. its protected by my dad's password and 2. I have stuff that I want to keep that I'll loose if I reset it to factory setting. Plz help? I've tried downloading any free app on the App Store and it does the same thing.

What app are you trying to download?

Space on iPhone screen where app should be...

I have posted once before, and I got nobody to respond.
I have a space on my iPhone where it looks like an application should be located. I searched...searched...searched, and the only place I see anything similar is on a blog (nobody reads).
See http://wordpress.pocosin.com/?p=453
See that black space? I have one on my iPhone too. I have not "broken" or "hacked" my phone like the blogger (I see cydia on the screen). Anyone know what the space is or how to get rid of it?

".....my brand new Macbook pro....."
Contact Apple Support immediately so they can start a case number. It's under warranty--your time is better spent working directly with Apple. Starting a case is your documentation that something happened under warranty--if the problem recurs outside of warranty, you and Apple both have evidence that it started during the warranty period.
These are user-to-user forums so Apple are not going to post official tech support here, nor respond to posts.

IPad3 ios 7 wifi broken

Upgraded to ios7 via Settings > General > Software Update on an iPad3 (wifi + verizon 4g) and now Wifi is totally broken.
Symptoms include seeing only a few hot spots and then they disappear even though we are standing right underneath the AP (my ios7 upgrade on my iphone 4s went flawlessly)
Trying to connect directly to the wireless AP (public one) by entering in the AP manually results in a couple distinct errors: Cannot Find The Network and "Cannot Scan For Wireless Networks"
I performed a full factory reset and now absolutely nothing. Cannot set up my ipad via wifi -or- cellular. Any ideas? I could try to sync with iTunes once i get home to see if that solves the problem.

I have the same problem. WiFi is pretty much unusable at the moment since the update. Ipad 3 and Iphone 5 slow as a wet week. Every other device in my house is working fine.

HT6114 I need help hacking into my ipod i forgot the password and i cant factory reset it because the power button is broken?!

I need help hacking into my ipod i forgot the password and i cant factory reset it because the power button is broken?!

If your iPod Touch, iPhone, or iPad is Broken
Apple does not fix iDevices. Instead, they exchange yours for a refurbished or new replacement depending upon the age of your device and refurbished inventories. On rare occasions when there are no longer refurbished units for your older model, they may replace it with the next newer model.
ATTN: Beginning July 2013 Apple Stores are now equipped to do screen repairs/replacements in-house on iPhone 5 and 5C. In some cases while you wait. According to Apple this is the beginning of equipping Apple Stores with the resources needed to do most repairs for iPhones, iPads, and iPod Touches that would not require major replacements. Later in the year the services may be extended as Apple Stores become equipped and staffed with the proper repair expertise. So, if you need a screen repaired or a broken screen replaced or have your stuck Home button fixed, call your local Apple Store to see if they are now doing these in-house.
You may take your device to an Apple retailer for help or you may call Customer Service and arrange to send your device to Apple:
Apple Store Customer Service at 1-800-676-2775 or visit online Help for more information.
To contact product and tech support: Contacting Apple for support and service - this includes international calling numbers.
You will find respective repair costs in the appropriate link:
iPod Service Support and Costs
iPhone Service Support and Costs
iPad Service Support and Costs
There are third-party firms that do repairs on iDevices, and there are places where you can order parts to DIY if you feel up to the task:
1. iResq or Google for others.
2. Buy and replace screen yourself: iFixit
Locked Out, Forgot Lock or Restrictions Passcode, or Need to Restore Your Device: Several Alternative Solutions
A
1. iOS- Forgotten passcode or device disabled after entering wrong passcode
2. iPhone, iPad, iPod touch: Wrong passcode results in red disabled screen
3. Restoring iPod touch after forgotten passcode
4. What to Do If You've Forgotten Your iPhone's Passcode
5. iOS- Understanding passcodes
6. iTunes 10 for Mac- Update and restore software on iPod, iPhone, or iPad
7. iOS - Unable to update or restore
Forgotten Restrictions Passcode Help
iPad,iPod,iPod Touch Recovery Mode
You will need to restore your device as New to remove a Restrictions passcode. Go through the normal process to restore your device, but when you see the options to restore as New or from a backup, be sure to choose New.
You can restore from a backup if you have one from BEFORE you set the restrictions passcode.
Also, see iTunes- Restoring iOS software.

Replacing broken 3g with a privately purchased g3 (no hacks)

I am purchasing a used 3g iPhone from a friend after he recently upgraded to the 3gs, because I have a cracked screen from a drop (still works fine).
What to I have to do with ATT to swap phones, anything? Do I pull the sim chip out, place it in the new one, and activate it through iTunes, then restore one of my backups? Is it that simple?
I have applecare (just under one year left on the warranty) on the original cracked phone, and I am assuming they will not transfer it to the used phone I am purchasing. A genius stated I can contact applecare and they will 'refund' the unused portion of the applecare. Anyone out there have any experience with this?
Both phones are 16 GB 3g, both locked on ATT (no hacks).
Thanks for any information you can throw at me.
Spinner

I'm exhausted... Apple support have been a nightmare, 4 calls, first hung up on me, second was on for 30 minutes before telling me to contact a company that have not worked with apple in months but still keep getting calls, then on again to be told to submit via the web form, which never sent me a confirmation email and when I check the case number it says that it's empty.. tried phoning again and this time the girl on the end can't understand me (I'm a deployment engineer for a telecomms company and travel very widely worldwide but have never ever found it this difficult to have someone understand me).
I'm going to sit in a corner and cry now.

Ipad2 and Ipad3, cannot see Ipad2 user - worked ok for months, now broken. Like to know how to upgrade Ipad2 to IOS 5.1.1 (too many issues with IOS 6 - consider too risky)?

I have been using Facetime successfully for months to communicate with my elderly mother in the UK (I am located in Canada)? Today we tried Facetime and we could hear each other but I could not see her. She could see me ok however.
As I wasn't sure whether the problem was with my iPad or hers I made a FaceTime call to my brother-in-law in the UK, this call worked perfectly. I then tried a Factime call with a friend in Canada and it also worked fine.
My mother could see herself in the small window so we know that her camera must be working.
Here are the IOS versions for the four IOS devices used in these tests..
My mothers iPad 2: IOS 4.3.5
Brother-in-law's iPad 3: IOS 5.1.1
Friends iPhone: IOS 6
My iPad 3: IOS 5.1.1
My questions are as follows:
Q1/ Has anyone heard of Facetime problems between newer and older iPads as a result of Apple rolling out IOS 6 recently?
(maybe there have been some changes to the FaceTime servers as part of the IOS 6 rollout?)
Q2/ Is it possible to update my Mothers iPad 2 (IOS 4) to IOS 5.1.1 and do this without using a computer? (I would prefer her to update to 5.1.1 and hold off updating to 6 because of all the issues I read of users having problems with 6, including FaceTime issues)
My mother is in her 70's, and has no computing device other than her iPad. She can just about manage to figure out how to use the basic features of her iPad. Therefore the update process needs to be very easy and straightforward otherwise she is likely to get very confused, very quickly!
Facetime has been brilliant for my mother and keeping in touch with her son, thousands of miles away, we would really like to get Facetime working again.
Can anyone help?

You will not be able to block IOS 6. You can try blocking it with a webfilter or firewall but if the students take these home or connect to another network or iTunes they can get it that way. You will find that the vast majority of all apps will work with 6 or have been updated to work with it by now.

How do I know if my router is broken or has been hacked?

I have a WRT54G and it stopped working. It's wifi gives off a single but no one can connect to it, and neither can I. The only way I can get online is by directly hooking my computer into my modem. I've reset the factory defaults and made my domain name my isp (satx.rr.com) Are there any other settings I need to fill in so I can get online? Thanks.

1)connect the modem to the router's internet port and the computer to the port#1
2)from the wired computer ,access the router using http://192.168.1.1 .. the default login password is admin
3)on the web ui , click on the "mac add clone" subtab , enable it and click clone..save the settings and do a power cycle
4)go to the "status" tab and check whether it has a valid internet ip add
5)if there is one , try going online ..

Is My apache http file okay? Could have been hacked?????Why would 12.34.56.78:80 be the listening address I don't have any AT&T Services12

I believe my apache server could have been hacked. Is there a member of the community that could take a look at the paste of my http.conf file. Thanks so much
# Mac OS X / Mac OS X Server
# The <IfDefine> blocks segregate server-specific directives
# and also directives that only apply when Web Sharing or
# server Web Service (as opposed to other services that need Apache) is on.
# The launchd plist sets appropriate Define parameters.
# Generally, desktop has no vhosts and server does; server has added modules,
# custom virtual hosts are only activated when Web Service is on, and
# default document root and personal web sites at ~username are only
# activated when Web Sharing is on.
# This is the main Apache HTTP server configuration file. It contains the
# configuration directives that give the server its instructions.
# See <URL:http://httpd.apache.org/docs/2.2> for detailed information.
# In particular, see
# <URL:http://httpd.apache.org/docs/2.2/mod/directives.html>
# for a discussion of each configuration directive.
# Do NOT simply read the instructions in here without understanding
# what they do. They're here only as hints or reminders. If you are unsure
# consult the online docs. You have been warned.
# Configuration and logfile names: If the filenames you specify for many
# of the server's control files begin with "/" (or "drive:/" for Win32), the
# server will use that explicit path. If the filenames do *not* begin
# with "/", the value of ServerRoot is prepended -- so "log/foo_log"
# with ServerRoot set to "/usr" will be interpreted by the
# server as "/usr/log/foo_log".
# ServerRoot: The top of the directory tree under which the server's
# configuration, error, and log files are kept.
# Do not add a slash at the end of the directory path. If you point
# ServerRoot at a non-local disk, be sure to point the LockFile directive
# at a local disk. If you wish to share the same ServerRoot for multiple
# httpd daemons, you will need to change at least LockFile and PidFile.
ServerRoot "/usr"
# Listen: Allows you to bind Apache to specific IP addresses and/or
# ports, instead of the default. See also the <VirtualHost>
# directive.
# Change this to Listen on specific IP addresses as shown below to
# prevent Apache from glomming onto all bound IP addresses.
#Listen 12.34.56.78:80
<IfDefine !MACOSXSERVER>
Listen 80
</IfDefine>
# Dynamic Shared Object (DSO) Support
# To be able to use the functionality of a module which was built as a DSO you
# have to place corresponding `LoadModule' lines at this location so the
# directives contained in it are actually available _before_ they are used.
# Statically compiled modules (those listed by `httpd -l') do not need
# to be loaded here.
# Example:
# LoadModule foo_module modules/mod_foo.so
LoadModule authn_file_module libexec/apache2/mod_authn_file.so
LoadModule authz_host_module libexec/apache2/mod_authz_host.so
LoadModule cache_module libexec/apache2/mod_cache.so
LoadModule disk_cache_module libexec/apache2/mod_disk_cache.so
LoadModule dumpio_module libexec/apache2/mod_dumpio.so
LoadModule reqtimeout_module libexec/apache2/mod_reqtimeout.so
LoadModule ext_filter_module libexec/apache2/mod_ext_filter.so
LoadModule include_module libexec/apache2/mod_include.so
LoadModule filter_module libexec/apache2/mod_filter.so
LoadModule substitute_module libexec/apache2/mod_substitute.so
LoadModule deflate_module libexec/apache2/mod_deflate.so
LoadModule log_config_module libexec/apache2/mod_log_config.so
LoadModule log_forensic_module libexec/apache2/mod_log_forensic.so
LoadModule logio_module libexec/apache2/mod_logio.so
LoadModule env_module libexec/apache2/mod_env.so
LoadModule mime_magic_module libexec/apache2/mod_mime_magic.so
LoadModule cern_meta_module libexec/apache2/mod_cern_meta.so
LoadModule expires_module libexec/apache2/mod_expires.so
LoadModule headers_module libexec/apache2/mod_headers.so
LoadModule ident_module libexec/apache2/mod_ident.so
LoadModule usertrack_module libexec/apache2/mod_usertrack.so
#LoadModule unique_id_module libexec/apache2/mod_unique_id.so
LoadModule setenvif_module libexec/apache2/mod_setenvif.so
LoadModule version_module libexec/apache2/mod_version.so
LoadModule proxy_module libexec/apache2/mod_proxy.so
LoadModule proxy_http_module libexec/apache2/mod_proxy_http.so
LoadModule proxy_scgi_module libexec/apache2/mod_proxy_scgi.so
LoadModule proxy_balancer_module libexec/apache2/mod_proxy_balancer.so
LoadModule ssl_module libexec/apache2/mod_ssl.so
LoadModule mime_module libexec/apache2/mod_mime.so
LoadModule dav_module libexec/apache2/mod_dav.so
LoadModule autoindex_module libexec/apache2/mod_autoindex.so
LoadModule asis_module libexec/apache2/mod_asis.so
LoadModule info_module libexec/apache2/mod_info.so
LoadModule cgi_module libexec/apache2/mod_cgi.so
LoadModule dav_fs_module libexec/apache2/mod_dav_fs.so
LoadModule vhost_alias_module libexec/apache2/mod_vhost_alias.so
LoadModule negotiation_module libexec/apache2/mod_negotiation.so
LoadModule dir_module libexec/apache2/mod_dir.so
LoadModule imagemap_module libexec/apache2/mod_imagemap.so
LoadModule actions_module libexec/apache2/mod_actions.so
LoadModule speling_module libexec/apache2/mod_speling.so
LoadModule alias_module libexec/apache2/mod_alias.so
LoadModule rewrite_module libexec/apache2/mod_rewrite.so
LoadModule php5_module libexec/apache2/libphp5.so
#Apple specific modules
LoadModule apple_userdir_module libexec/apache2/mod_userdir_apple.so
LoadModule bonjour_module libexec/apache2/mod_bonjour.so
<IfDefine !MACOSXSERVER>
LoadModule authn_dbm_module libexec/apache2/mod_authn_dbm.so
LoadModule authn_anon_module libexec/apache2/mod_authn_anon.so
LoadModule authn_dbd_module libexec/apache2/mod_authn_dbd.so
LoadModule authn_default_module libexec/apache2/mod_authn_default.so
LoadModule auth_basic_module libexec/apache2/mod_auth_basic.so
LoadModule auth_digest_module libexec/apache2/mod_auth_digest.so
LoadModule authz_groupfile_module libexec/apache2/mod_authz_groupfile.so
LoadModule authz_user_module libexec/apache2/mod_authz_user.so
LoadModule authz_dbm_module libexec/apache2/mod_authz_dbm.so
LoadModule authz_owner_module libexec/apache2/mod_authz_owner.so
LoadModule authz_default_module libexec/apache2/mod_authz_default.so
LoadModule mem_cache_module libexec/apache2/mod_mem_cache.so
LoadModule dbd_module libexec/apache2/mod_dbd.so
LoadModule proxy_connect_module libexec/apache2/mod_proxy_connect.so
LoadModule proxy_ftp_module libexec/apache2/mod_proxy_ftp.so
LoadModule proxy_ajp_module libexec/apache2/mod_proxy_ajp.so
LoadModule status_module libexec/apache2/mod_status.so
</IfDefine>
<IfDefine MACOSXSERVER>
LoadModule hfs_apple_module libexec/apache2/mod_hfs_apple.so
#LoadModule auth_digest_apple_module libexec/apache2/mod_auth_digest_apple.so
#LoadModule encoding_module libexec/apache2/mod_encoding.so
#LoadModule jk_module libexec/apache2/mod_jk.so
LoadModule apple_auth_module libexec/apache2/mod_auth_apple.so
LoadModule spnego_auth_module libexec/apache2/mod_spnego_apple.so
LoadModule apple_digest_module libexec/apache2/mod_digest_apple.so
#LoadModule python_module libexec/apache2/mod_python.so
LoadModule xsendfile_module libexec/apache2/mod_xsendfile.so
LoadModule apple_status_module libexec/apache2/mod_status_apple.so
</IfDefine>
# If you wish httpd to run as a different user or group, you must run
# httpd as root initially and it will switch.
# User/Group: The name (or #number) of the user/group to run httpd as.
# It is usually good practice to create a dedicated user and group for
# running httpd, as with most system services.
User _www
Group _www
# 'Main' server configuration
# The directives in this section set up the values used by the 'main'
# server, which responds to any requests that aren't handled by a
# <VirtualHost> definition. These values also provide defaults for
# any <VirtualHost> containers you may define later in the file.
# All of these directives may appear inside <VirtualHost> containers,
# in which case these default settings will be overridden for the
# virtual host being defined.
# ServerAdmin: Your address, where problems with the server should be
# e-mailed. This address appears on some server-generated pages, such
# as error documents. e.g. [email protected]
ServerAdmin [email protected]
# ServerName gives the name and port that the server uses to identify itself.
# This can often be determined automatically, but we recommend you specify
# it explicitly to prevent problems during startup.
# If your host doesn't have a registered DNS name, enter its IP address here.
#ServerName www.example.com:80
<IfDefine MACOSXSERVER>
DocumentRoot /var/empty
<IfModule mod_auth_digest_apple.c>
        BrowserMatch "MSIE" AuthDigestEnableQueryStringHack=On
</IfModule>
<IfModule mod_headers.c>
        Header add MS-Author-Via "DAV"
        RequestHeader set X_FORWARDED_PROTO 'https' env=https
        RequestHeader set X_FORWARDED_PROTO 'http' env=!https
</IfModule>
<IfModule mod_encoding.c>
        EncodingEngine on
        NormalizeUsername on
        DefaultClientEncoding UTF-8
# Windows XP?
        AddClientEncoding "Microsoft-WebDAV-MiniRedir/" MSUTF-8
# Windows 2K SP2 with .NET
        AddClientEncoding "(Microsoft .* DAV\$)" MSUTF-8
# Windows 2K SP2/Windows XP
        AddClientEncoding "(Microsoft .* DAV 1.1)" CP932
# Windows XP?
        AddClientEncoding "Microsoft-WebDAV*" CP932
# RealPlayer
        AddClientEncoding "RMA/*" CP932
# MacOS X webdavfs
        AddClientEncoding "WebDAVFS" UTF-8
# cadaver
        AddClientEncoding "cadaver/" EUC-JP
</IfModule>
<Directory /usr/share/web>
    AllowOverride None
    Options MultiViews FollowSymlinks
    Order allow,deny
    Allow from all
    Header Set Cache-Control no-cache
</Directory>
Alias /webmail /usr/share/web/webmail.html
Alias /changepassword /usr/share/web/changepassword.html
Alias /profilemanager /usr/share/web/profilemanager.html
Alias /webcal /usr/share/web/webcal.html
</IfDefine>
<IfDefine !MACOSXSERVER>
<IfDefine WEBSHARING_ON>
# DocumentRoot: The directory out of which you will serve your
# documents. By default, all requests are taken from this directory, but
# symbolic links and aliases may be used to point to other locations.
DocumentRoot "/Library/WebServer/Documents"
# Each directory to which Apache has access can be configured with respect
# to which services and features are allowed and/or disabled in that
# directory (and its subdirectories).
# First, we configure the "default" to be a very restrictive set of
# features.
<Directory />
    Options FollowSymLinks
    AllowOverride None
    Order deny,allow
    Deny from all
</Directory>
# Note that from this point forward you must specifically allow
# particular features to be enabled - so if something's not working as
# you might expect, make sure that you have specifically enabled it
# below.
# This should be changed to whatever you set DocumentRoot to.
<Directory "/Library/WebServer/Documents">
    # Possible values for the Options directive are "None", "All",
    # or any combination of:
    #   Indexes Includes FollowSymLinks SymLinksifOwnerMatch ExecCGI MultiViews
    # Note that "MultiViews" must be named *explicitly* --- "Options All"
    # doesn't give it to you.
    # The Options directive is both complicated and important. Please see
    # http://httpd.apache.org/docs/2.2/mod/core.html#options
    # for more information.
    Options Indexes FollowSymLinks MultiViews
    # AllowOverride controls what directives may be placed in .htaccess files.
    # It can be "All", "None", or any combination of the keywords:
    #   Options FileInfo AuthConfig Limit
    AllowOverride None
    # Controls who can get stuff from this server.
    Order allow,deny
    Allow from all
</Directory>
# DirectoryIndex: sets the file that Apache will serve if a directory
# is requested.
<IfModule dir_module>
    DirectoryIndex index.html
</IfModule>
</IfDefine>
</IfDefine>
# The following lines prevent .htaccess and .htpasswd files from being
# viewed by Web clients.
<FilesMatch "^\.([Hh][Tt]|[Dd][Ss]_[Ss])">
    Order allow,deny
    Deny from all
    Satisfy All
</FilesMatch>
# Apple specific filesystem protection.
<Files "rsrc">
    Order allow,deny
    Deny from all
    Satisfy All
</Files>
<DirectoryMatch ".*\.\.namedfork">
    Order allow,deny
    Deny from all
    Satisfy All
</DirectoryMatch>
# ErrorLog: The location of the error log file.
# If you do not specify an ErrorLog directive within a <VirtualHost>
# container, error messages relating to that virtual host will be
# logged here. If you *do* define an error logfile for a <VirtualHost>
# container, that host's errors will be logged there and not here.
ErrorLog "/private/var/log/apache2/error_log"
# LogLevel: Control the number of messages logged to the error_log.
# Possible values include: debug, info, notice, warn, error, crit,
# alert, emerg.
LogLevel warn
<IfModule log_config_module>
    # The following directives define some format nicknames for use with
    # a CustomLog directive (see below).
    LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" combined
    LogFormat "%v %h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" combinedvhost
    LogFormat "%h %l %u %t \"%r\" %>s %b" common
    LogFormat "%v %h %l %u %t \"%r\" %>s %b" commonvhost
    <IfModule logio_module>
      # You need to enable mod_logio.c to use %I and %O
      LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\" %I %O" combinedio
      LogFormat "%v %h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\" %I %O" combinediovhost
    </IfModule>
    # The location and format of the access logfile (Common Logfile Format).
    # If you do not define any access logfiles within a <VirtualHost>
    # container, they will be logged here. Contrariwise, if you *do*
    # define per-<VirtualHost> access logfiles, transactions will be
    # logged therein and *not* in this file.
    CustomLog "/private/var/log/apache2/access_log" common
    # If you prefer a logfile with access, agent, and referer information
    # (Combined Logfile Format) you can use the following directive.
    #CustomLog "/private/var/log/apache2/access_log" combined
</IfModule>
<IfModule alias_module>
    # Redirect: Allows you to tell clients about documents that used to
    # exist in your server's namespace, but do not anymore. The client
    # will make a new request for the document at its new location.
    # Example:
    # Redirect permanent /foo http://www.example.com/bar
    # Alias: Maps web paths into filesystem paths and is used to
    # access content that does not live under the DocumentRoot.
    # Example:
    # Alias /webpath /full/filesystem/path
    # If you include a trailing / on /webpath then the server will
    # require it to be present in the URL. You will also likely
    # need to provide a <Directory> section to allow access to
    # the filesystem path.
    # ScriptAlias: This controls which directories contain server scripts.
    # ScriptAliases are essentially the same as Aliases, except that
    # documents in the target directory are treated as applications and
    # run by the server when requested rather than as documents sent to the
    # client. The same rules about trailing "/" apply to ScriptAlias
    # directives as to Alias.
    ScriptAliasMatch ^/cgi-bin/((?!(?i:webobjects)).*$) "/Library/WebServer/CGI-Executables/$1"
</IfModule>
<IfModule cgid_module>
    # ScriptSock: On threaded servers, designate the path to the UNIX
    # socket used to communicate with the CGI daemon of mod_cgid.
    #Scriptsock /private/var/run/cgisock
</IfModule>
# "/Library/WebServer/CGI-Executables" should be changed to whatever your ScriptAliased
# CGI directory exists, if you have that configured.
<Directory "/Library/WebServer/CGI-Executables">
    AllowOverride None
    Options None
    Order allow,deny
    Allow from all
</Directory>
# DefaultType: the default MIME type the server will use for a document
# if it cannot otherwise determine one, such as from filename extensions.
# If your server contains mostly text or HTML documents, "text/plain" is
# a good value. If most of your content is binary, such as applications
# or images, you may want to use "application/octet-stream" instead to
# keep browsers from trying to display binary files as though they are
# text.
DefaultType text/plain
<IfModule mime_module>
    # TypesConfig points to the file containing the list of mappings from
    # filename extension to MIME-type.
    TypesConfig /private/etc/apache2/mime.types
    # AddType allows you to add to or override the MIME configuration
    # file specified in TypesConfig for specific file types.
    #AddType application/x-gzip .tgz
    # AddEncoding allows you to have certain browsers uncompress
    # information on the fly. Note: Not all browsers support this.
    #AddEncoding x-compress .Z
    #AddEncoding x-gzip .gz .tgz
    # If the AddEncoding directives above are commented-out, then you
    # probably should define those extensions to indicate media types:
    AddType application/x-compress .Z
    AddType application/x-gzip .gz .tgz
    # AddHandler allows you to map certain file extensions to "handlers":
    # actions unrelated to filetype. These can be either built into the server
    # or added with the Action directive (see below)
    # To use CGI scripts outside of ScriptAliased directories:
    # (You will also need to add "ExecCGI" to the "Options" directive.)
    #AddHandler cgi-script .cgi
    # For type maps (negotiated resources):
    #AddHandler type-map var
    # Filters allow you to process content before it is sent to the client.
    # To parse .shtml files for server-side includes (SSI):
    # (You will also need to add "Includes" to the "Options" directive.)
    #AddType text/html .shtml
    #AddOutputFilter INCLUDES .shtml
</IfModule>
# The mod_mime_magic module allows the server to use various hints from the
# contents of the file itself to determine its type. The MIMEMagicFile
# directive tells the module where the hint definitions are located.
#MIMEMagicFile /private/etc/apache2/magic
# Customizable error responses come in three flavors:
# 1) plain text 2) local redirects 3) external redirects
# Some examples:
#ErrorDocument 500 "The server made a boo boo."
#ErrorDocument 404 /missing.html
#ErrorDocument 404 "/cgi-bin/missing_handler.pl"
#ErrorDocument 402 http://www.example.com/subscription_info.html
# EnableMMAP and EnableSendfile: On systems that support it,
# memory-mapping or the sendfile syscall is used to deliver
# files. This usually improves server performance, but must
# be turned off when serving from networked-mounted
# filesystems or if support for these functions is otherwise
# broken on your system.
#EnableMMAP off
#EnableSendfile off
TraceEnable off
# Supplemental configuration
# The configuration files in the /private/etc/apache2/extra/ directory can be
# included to add extra features or to modify the default configuration of
# the server, or you may simply copy their contents here and change as
# necessary.
# Server-pool management (MPM prefork specific)
StartServers 1
MinSpareServers 1
MaxSpareServers 1
# ServerLimit and MaxClients support n% syntax which sets them to a
# fraction of the current RLIMIT_NPROC limit.
ServerLimit 50%
MaxClients 50%
ListenBackLog 512
MaxRequestsPerChild 100000
# Timeout: The number of seconds before receives and sends time out.
Timeout 300
# KeepAlive: Whether or not to allow persistent connections (more than
# one request per connection). Set to "Off" to deactivate.
KeepAlive On
# KeepAliveTimeout: Number of seconds to wait for the next request from the
# same client on the same connection.
KeepAliveTimeout 15
# MaxKeepAliveRequests: The maximum number of requests to allow
# during a persistent connection. Set to 0 to allow an unlimited amount.
# We recommend you leave this number high, for maximum performance.
MaxKeepAliveRequests 100
# UseCanonicalName: Determines how Apache constructs self-referencing
# URLs and the SERVER_NAME and SERVER_PORT variables.
# When set "Off", Apache will use the Hostname and Port supplied
# by the client. When set "On", Apache will use the value of the
# ServerName directive.
UseCanonicalName Off
# AccessFileName: The name of the file to look for in each directory
# for additional configuration directives. See also the AllowOverride
# directive.
AccessFileName .htaccess
# ServerTokens
# This directive configures what you return as the Server HTTP response
# Header. The default is 'Full' which sends information about the OS-Type
# and compiled in modules.
# Set to one of: Full | OS | Minor | Minimal | Major | Prod
# where Full conveys the most information, and Prod the least.
ServerTokens Full
# Optionally add a line containing the server version and virtual host
# name to server-generated pages (internal error documents, FTP directory
# listings, mod_status and mod_info output etc., but not CGI generated
# documents or custom error documents).
# Set to "EMail" to also include a mailto: link to the ServerAdmin.
# Set to one of: On | Off | EMail
ServerSignature On
# HostnameLookups: Log the names of clients or just their IP addresses
# e.g., www.apache.org (on) or 204.62.129.132 (off).
# The default is off because it'd be overall better for the net if people
# had to knowingly turn this feature on, since enabling it means that
# each client request will result in AT LEAST one lookup request to the
# nameserver.
HostnameLookups Off
# PidFile: The file in which the server should record its process
# identification number when it starts.
PidFile /var/run/httpd.pid
# The accept serialization lock file MUST BE STORED ON A LOCAL DISK.
LockFile "/private/var/log/apache2/accept.lock"
<IfModule mod_rewrite.c>
    RewriteLock /var/log/apache2/rewrite.lock
</IfModule>
# Language settings
Include /private/etc/apache2/extra/httpd-languages.conf
<IfDefine WEBSHARING_ON>
# Multi    -language error messages
#Include /private/etc/apache2/extra/httpd-multilang-errordoc.conf
# Fancy directory listings
Include /private/etc/apache2/extra/httpd-autoindex.conf
# User home directories
Include /private/etc/apache2/extra/httpd-userdir.conf
# Real-time info on requests and configuration
#Include /private/etc/apache2/extra/httpd-info.conf
# Virtual hosts
#Include /private/etc/apache2/extra/httpd-vhosts.conf
# Local access to the Apache HTTP Server Manual
Include /private/etc/apache2/extra/httpd-manual.conf
# Distributed authoring and versioning (WebDAV)
#Include /private/etc/apache2/extra/httpd-dav.conf
</IfDefine>
# Secure (SSL/TLS) connections
<IfDefine !MACOSXSERVER>
#Include /private/etc/apache2/extra/httpd-ssl.conf
</IfDefine>
<IfDefine MACOSXSERVER>
<IfModule mod_ssl.c>
        SetEnvIf User-Agent ".*MSIE.*" nokeepalive ssl-unclean-shutdown
        SSLPassPhraseDialog exec:/etc/apache2/getsslpassphrase
        SSLSessionCache shmcb:/var/run/ssl_scache(512000)
        SSLSessionCacheTimeout 300
        SSLMutex file:/var/run/ssl_mutex
        SSLRandomSeed startup builtin
        SSLRandomSeed connect builtin
        AddType application/x-x509-ca-cert crt
        AddType application/x-pkcs7-crl crl
</IfModule>
</IfDefine>
<IfModule mod_jk.c>
        JKWorkersFile /etc/apache2/workers.properties
        JKLogFile /var/log/apache2/mod_jk.log
        JkShmFile /var/log/apache2/jk-runtime-status
</IfModule>
<IfModule php5_module>
    AddType application/x-httpd-php .php
    AddType application/x-httpd-php-source .phps
    <IfModule dir_module>
        DirectoryIndex index.html index.php
    </IfModule>
</IfModule>
<IfDefine !MACOSXSERVER>
    Include /etc/apache2/other/*.conf
</IfDefine>
<IfDefine MACOSXSERVER>
    <IfDefine WEBSERVICE_ON>
        Include /etc/apache2/sites/*.conf
    </IfDefine>
    <IfDefine !WEBSERVICE_ON>
        Include /etc/apache2/sites/virtual_host_global.conf
        Include /etc/apache2/sites/*_.conf
        Include /etc/apache2/sites/*__shadow.conf
    </IfDefine>
</IfDefine>

That's a comment in the file. It has no effect at all.

CFChart images broken when creating a PDF document with SSL

I have a report that I create with Coldfusion, that includes a number of CFChart objects. I recently installed a new SSL certificate, and now all the charts show up as broken links.   It shows up fine if I try and display this as HTML. On the chance it was something weird about my (lengthly) report, I created the following sample code that I saved in a file called foo.cfm:
<cfset sDir = "C:/">
<cfset filename = "foo123.pdf">
<cfdocument format="pdf" filename="#filename#" overwrite="yes" marginleft=".7" margintop=".3" backgroundvisible="yes">
TEST 12345
<br>
<br>
<div style="height:500px;float:right; margin-left:10px; margin-top:10px; margin-right:10px; margin-bottom:10px;">
    <cfchart
        format="png"
        chartwidth="400"
        chartheight="360"
        showborder="no"
        databackgroundcolor="##ffffff"
        fontbold="yes"
        sortxaxis="no"
        yoffset=".1"
        scaleto="100"
        showmarkers="no"
        show3d="no"
        fontsize="11"
          >
    <cfchartseries type="bar" datalabelstyle="none" seriescolor="##00CC99" paintstyle="shade">
    <cfchartdata item="B" value="40">
    <cfchartdata item="A" value="50">
    <cfchartdata item="E" value="80">
    <cfchartdata item="S" value="30">
    </cfchartseries>
    </cfchart>
</div>
</cfdocument>
<cfoutput>
<a href="#filename#" target="_blank">Foo</a>
</cfoutput>
If I go to the URL https://www.mywebsite.com/foo.cfm, the foo.pdf file shows a broken link. If instead I go to http://www.mywebsite.com/foo.cfm the image of the chart shows up just fine.
The weird thing is that I have an older server running CF9.0.0. On this server it works just fine. On another server with 9.0.1, it breaks. Same with 9.0.2, and CF 10.
I read something about needing to install the cert in a keystore, and I did this but it changed nothing. The image is still broken in the pdf.
Any help would be greatly appreciated. We have been able to work around the issue by posting the image in a non-secure location, but this seems like a hack, not a proper solution.

Hi Anit, thanks for the feedback. I did try this on a different server, using the instructions here:
http://helpx.adobe.com/coldfusion/kb/import-certificates-certificate-stores-coldfusion.htm l
and then restarted ColdFusion, but it didn't seem to fix the issue. How would I check that the certificate has been correctly imported? Also, how can I define what URL Coldfusion uses to get the images it creates with CFChart?   Though it seems to me this should "just work" by default, if I've followed the steps correctly, and I should have to edit any config files.

My MacBook air is hacked.

Hi !
I need some help. From someone with really great knowledge and connections.
(but I'm going to write a bad question (maybe) because I'm fed up with idiotic know-how insides like "how to write a good question". a question is always good, mind you. But I don't know if I should post it in another topic, if so, feel free to fix that, anyone, thx).
I just bought a mac book air, and strange things are happening.
For instance, the computer would block, I can't click anywhere with any result for sth like 30 sec. It's brand new. I've just unpacked it.
Or the bookmarks in safari were strange, because there was my own bank in it (+ apple + google maps + wikipedias + misc.). (I'm not suffering any memory affection or anything).
Or I just did a research with google (sim city) and results appeared with "Disney" in the research field.
To set the scene, my Facebook and Twitter accounts are quite often hacked, with the same subtle processes. (like" they" or God maybe, someone who's not me, would add some followers supposedly added a few weeks ago, and so on). I think I'm being followed by a few excited engineers with great extended connections (because (probably) I filed a case against them, for...harassment. (It's been going on for a few years and I'm really, really tired, given that they used the info they got to destroy my life , social relations and career )
I can't believe a just-bought-just-started computer could be hacked so easily. Although I had logged into my apple account. And they got my Ip address. But the only things I downloaded were uploads from the app store.
How can you prove your computer is being hacked?
Thank you (in advance and a lot) to anyone who can help.

Hello, thanks for answering !
I don't know what they want, and I can't make you understand how it feels to be constantly "spied" on whatever you're doing - especially work when you're not someone who believes she does everything right or ever will or ever wants to be that kind of person. They made me lose hours and hours with my printer, lose documents, and so on.
If you were a hacker, benwiggy you'd be caught. Probably. On the long term, that is.
If you push the game too much, then it's too obvious and cops will have to react. It won't last. It's much more fun to drive someone mad with no possibility to assert her basic rights, for lack of proofs. (therefore the quicktime solution is not a bad one, although it does not fix everything. Yesterday I got a video of my mouse moving by itself right in the middle of something I was doing (entering an email address) on this computer but still, it's no obvious proof, I could have done it myself (say you're typing extremely fast with just one hand, using the other to click right on the other field).
It's much more efficient than crashing a hard drive.And not less annoying. And I did crash my hard drive all by myself, twice, after several complete reinstallation of mac os on my previous computer. And then, I was so annoyed by their little game that I banged my fist on the computer, which did not prove convincing. At the end of the day, that's two hard drives and one complete machine broken, just on me.
Anyway, speaking about it is a good defensive mean, so thank you.
I think people should know about this category of hacking. It's quite disgusting. I would prefer a good hacker attack, with a pirate boat flashing several times on my screen, and then the whole thing exploding.That would be sort of fair piracy. (But mines are cowards).

IPad3 broken or hacked?

Similar Messages

Maybe you are looking for