Iphone 2g connect to itunes mode pc doesn't recognise
Hi,
I am not sure how or why but my iphone went blank today, I assumed that the phone had run out of battery, I plugged it in but it did not seem to charge. Next the symbols for connect to itunes came up so I connected it to my laptop but itunes would not recognise it, the symbols stayed on then it reset after a few minutes. I have reset the phone and nothing. The phone is locked to O2 and it has a tesco mobile sim installed. I have had the phone for 3 months and it has worked fine.
Thanks for your help
Furter details with this problem, I got the phone to charge by removing the sim and placing in my Gear4 speaker, once charged I put the sim back in started the phone and it seemed fine except that the home button will not work at all! Crazy, as soon as I plug it in the PC the connect to itunes pops up and itunes still wont recognise.
Any help ideas what could of caused this?
Similar Messages
-
Iphone 2g connect to itunes mode and pc doesn't recognise
Hi,
I am not sure how or why but my iphone went blank today, I assumed that the phone had run out of battery, I plugged it in but it did not seem to charge. Next the symbols for connect to itunes came up so I connected it to my laptop but itunes would not recognise it, the symbols stayed on then it reset after a few minutes. I have reset the phone and nothing. The phone is locked to O2 and it has a tesco mobile sim installed. I have had the phone for 3 months and it has worked fine.
Thanks for your helpPhoenixfc7 wrote:
I am not sure how or why but my iphone...
Hi Phoenix,
Welcome to Apple discussions.
I think you missed a sign somewhere along the information highway. This is the Numbers '09 forum, where the general topics concern techniques and issues involving Apple's spreadsheet application Numbers '09, part of the iWork '09 collection.
Your question will likely be served better if asked one of the forums in the iPhone section of Discussions. The link will take you to that section.
Regards,
Barry -
My phone goes into "connect to Itunes" mode and locks up, I connect to Itunes and do a restore and then within 24 hours I get the same message again and the phone locks up. any ideas ?
You're welcome.
A hardware problem doesn't mean complete failure.
With a computer, a hard drive can have a partial or complete failure.
If it wasn't a hardware problem, it would be resolved after restoring the iPhone as a new iPhone or not from the backup. If not, every iPhone running 5.1.1 would have the same problem. -
My iphone 3gs will not connect to itunes and it says that I need to do a system restore. It also says that I need to enter my password on the iphone to connect to itunes but I can not do this because the phone is in emergency phone call mode only.
Turn your phone off and connect your cable to the computer, but not the device just yet. Start up iTunes. Now, hold down the home button on your phone and plug it in to the cable - don't let go of the button until iTunes tells you it's detected a phone in recovery mode. Now you can restore to factory settings.
Unfortunately, the data on your phone is already gone if you're seeing the connect to iTunes logo. -
I have tried to update my Iphone 4S today to IOS 7.0.6 and now my iphone wont connect to itunes as it says that it is detected that it is in recovery mode and needs restoring. How do I restore it? I cannot get my phone on at all?
Click restore in itunes.
-
my iphone 3g is stuck on the connect to itunes mode and it wont show up on itunes. itunes hasnt even detected it on recovery mode. what do i do i really need my phone.. please help
Please stop altering the fonts, it makes reading postings extremely difficult. If help is desired, making postings difficult to read is not the way to get help.
Put the device in DFU mode (google it), then restore. -
How do I get a factory unlocked iPhone 3GS out of (connect to iTunes) mode?
How do I get a factory unlocked iPhone 3GS out of recovery (connect to itunes) mode?
Once the iPhone 3GS is in DFU mode and plugged into iTunes, the restore and update process begins. The restores process are as followed:
Extracting software > Preparing iPhone for restore (blank screen) > Preparing iPhone software for restore > Restoring iPhone software > Verifying iPhone restore > Restoring iPhone firmware > The iPhone cannot be restored. An unknown error occurred (1).
I clicked on the more information tab and was taken to a website with some troubleshooting. I did what they suggested (based on the error #) and still no luck. I’ve tried to restore and update about 10 times now but the same message keeps coming up at the end. What should I do now?
P.S: I have the latest version of iTunes (11), my windows is up to date etc ...CDiiva wrote:
The iPhone cannot be restored. An unknown error occurred (1).
This Error message is indicative of a Hardware issue. The device may need Service. -
My iPhone 3gs is not working properly and hasn't been since about September of last year. When switched on (Quite often it won't even turn on) it says 'Update Completed' as though it has just been updated. On the next screen it says to 'Connect to iTunes'. It doesn't, however, connect to iTunes and just resets itself over and over until power is gone. Occasionally after switching on and off a few times it functions normally for a few hours and some times even a couple of days but eventually always turns itself off and goes back to the 'Update Completed' screen. Does anyone know what might be causing this and/or a way of fixing it?
Morning JordenR,
Thanks for using Apple Support Communities.
You can resolve many restore issues using the troubleshooting steps documented here.
For more information on this, take a look at this article:
iOS: Resolving update and restore alert messages
http://support.apple.com/kb/ts1275
Best of luck,
Mario -
I have an iphone 3g that is stuck in connect to itunes mode it keeps coming up with error messege #1015 everytime i try to restore it
Generally a sign that the iPhone was jailbroken or modified to work with
other than the original wireless provider. Terms of Service for this forum
prohibit discussion of jailbroken iPhones.
Google may provide an answer. -
i just update my iPhone which was previously jailbreaked when i update it after downloading all the file it start to show the apple logo for a moment and it went and completely turned off i tried to connect through iTunes but it doesn't show any iPhone connected to itunes
No support for jailbroken phones will be given in this forum or from Apple.
Unauthorized modification of iOS has been a major source of instability, disruption of services, and… -
My Iphone 5 suddenly turned off and there is only the Itunes logo with the usb image and arrow key. I've now connected to Itunes but it doesn't work
Have a look through this Doc
http://support.apple.com/kb/TS3281 -
my iphone is stuck on connect to itunes mode!!!!! Plzz smb help me!!! What should i do? I am from albania and i have gone to any apple service here but no help!!!!
Hi enkifromtirane,
If you had an issue with your iPhone and are now seeing an icon screen instructing you to connect to iTunes, you may find the following article helpful:
Apple Support: If you can't update or restore your iOS device
http://support.apple.com/kb/ht1808
Regards,
- Brenden -
iPhone is connected to iTunes now iPhone is recovery mode i got message accurred no 2003 now iwant restore iPhone
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar
BTW, this is the iPod touch forum -
Cannot install IPhone 4 USB Driver, Phone stuck in "Connect to iTunes" mode
Hi.
I have the new Iphone 4 - for 2 days, and i can't install the Iphone 4 USB drivers. I tested the cable, the OS.. everything and now after reset i can't use my phone since its stuck in connect to Itunes mode.
Every time i try to connect the USB, Windows recognize it as "unknown device" with (Code 43). If i try manually to select the Driver from common/apple/drivers the error is (Code 10).
Tested the 2G and seems its connected without any problem and windows recognized the phone, but its not recognizing my Iphone 4 (tested on 2- Windows 7 OS), found some topic that Reset can help such issues, and now im stuck with Phone that have only emergency calls.
Using latest iTunes , and ver 4.0.2
Please help!!!!Same problem. This worked for me
http://www.youtube.com/watch?v=nQnb4wIxNFg&feature=fvwrel -
re started iphone after powering down, now is stuck in connect to itunes mode and wont do anything else. also has no service, I was able to retrieve all of my photos so the device is functional on that level. have restarted several times & also have restored data from i tunes. it said my phone is damaged.
Jailbreaking
Jailbreaking voids the Apple warranty and also means that you will not get any support from Apple, including from this Apple forum. Jailbreaking can't be discussed in this Apple forum.
Unauthorized modification of iOS has been a major source of instability, disruption of services, and other issues
Maybe you are looking for
-
Hi all, I am trying to install oim9.1 on windows xp. I have installed database 10.2.0.3 and OAS 10.1.3.1. I am unable to run the script prepare_xl_db.bat. "ERROR Database orcl is not running" I checked my DB, its up and running. So, i ignored this st
-
Issues with Exporting to Report Definition File
Post Author: dcasper70 CA Forum: Exporting We just notices a strange thing happening when exporting to a report definition file. Hoping someone can explain it and/or offer us some kind of solution. We're currently about 25 deep into an extensive do
-
I have updated version of Java and cannot open games from Club Pogo, how can I change security settings to allow the games to open? Thanks
-
we are extracting data from R3 and other databases using DB connect. data extracted via DB using Yen currency multiplies the result by 100. Transactions extracted from R3 using Yen currency are displayed correctly. checked the currency settings/ tab
-
Hi! I want to make a practicing log for my rehearsals in Excel. I want the opportunity to practice at least three times during a day and each time I practice during a day I want to save what I have practiced and for how long. For instance I can have