IPhone 3G v 3.0 very low volume in BMW

I've had my iPhone 3G successfully connected via BT to my 2007 BMW 530xi. Everything worked fine for over six months, but after I upgraded to version 3.0, the volume of an incoming call is significantly lower than prior to upgrading to 3.0. I have the car radio volume turned up as high as it goes. Anyone else notice the same problem.

While you are on a call on Bluetooth®, press the "up" volume button on the side of the iPhone. "Bluetooth Volume" will pop up on the iPhone screen, and you can increase it to max, which should solve your low volume problem.

Similar Messages

My call having very low volume to the caller

my call having very low volume to the lisner or caller . how to increase form my iphone.

Hey there pawan922,
It sounds like you are being told that your voice is not clear but they sound fine to you. I would use the troubleshooting in the following article to help resolve the issue here, named:
iPhone: Microphone issues
http://support.apple.com/kb/ts5183
Follow these steps, testing after each.
Make sure nothing is plugged in to the jack connector.
Make sure nothing is blocking any of the microphones (refer to the pictures below to find your device's microphones). Check for these:
Dirt or debris
A screen protector or case
When you're holding your phone next to your ear, make sure you don't block the microphone with your fingers or shoulder and make sure to speak into the microphone
Turn the iPhone off and then on.
Update to the latest version of iOS.
If necessary, find general iPhone hardware troubleshooting suggestions.
For further assistance, contact Apple Support.
If the issue persists and you need to make a call, try using headphones with an integrated microphone.
iPhone 4, iPhone 4s:
Top microphone
Bottom microphone
Thank you for using Apple Support Communities.
Regards,
Sterling

Very low volume on headphone jack on MBP 13" but no red light

Hi I am looking for solution for my problem where in I am currently getting very low volume on headphone jack. There was no problem before, everything used to work perfectly fine.
I couldn't find comprehensive solution for this. Could anyone please point me to the correct thread if solution is already available.
my details:
MBP 13" Snow leopard, 10.6.5 - First Gen. Unibody MAC.
problem: Very low volume when headphone is connected.
Things: I have tried:
1. Headphone is fine. Works correctly on windows PC and on my iphone.
2. Tried system pref. volume is max.
3. Upon connecting headphone to MBP it is detected as headphone.
4. Tried Audio MIDI setup, settings seem to be correct 44.1KHz 2ch-16 bit
5. There is NO red light from headphone jack.
6 Tried poking toothpicks in to audio out but didn't help.
7 Tried creating new temp. admin user account but headphone low volume remains.
8. Tried safe boot - no joy.
9 Safe boot was followed by normal boot-> Ran Disk Util tried repair permission. No luck.
10. Also followed steps to clear PR RAM etc. - problem remains.
11. Heard about logic board replacement but don't want to go by that route.
Can anyone point me to correct thread or provide the solution..
help is much appreciated.
Thanks...

I have the exact same problem. i have a macbook pro 13in (mid 2009) with extremely low volume coming from headphone jack. i brought the computer into my local apple store today and they diagnosed my problem as being the result of a faulty logic board. my laptop is out of warranty so they have to send it to the apple repair depot for 3-5 days. the charge is a flat $280 (tax not included). the solution seems extreme though and i hope i don't get any "kernel panicking" with a new board. i will update... also there is no accidental damge to my laptop whatsoever. the problem arrose 2-3wks ago

Hi. I Have a Pavilion dv9000 which has always had very low volume - really needs to be increased?

Hi. I Have a Pavilion dv9000 with Vista Ultimate 64. It has always had very low volume and I find I generally have to have the volume up into the 70's 80's as well as the onscreen media player slider almost full - which then gets all distorted - and then have to turn it down again when not using the player as the computer error beeps come screaming out., Ive checked the settings on speakers to make sure all are the same & balanced and also have updated any codecs as needed. Is there a sound lever setting elsewhere?
cheers

Thanks for the reply and peeling my post off Mike, sorry I didn't start my own initially.
Well @ 1333Mhz I was using the rated timings 9-9-9-24 (as per Corsair) but it wasn't very stable as I said.
I have since changed the FSB/RAM ratio to get 1066Mhz and it seemed much happier. (@1.5v) It would be nice to run the RAM at it's rated setting but my OC skills aren't that extensive. I imagine it would need alot of tweeking? Or could I have just relaxed the timings a bit?
Would removing the Switch Cards make any difference?
Thanks in advance.

Very low volume in the speaker

Dears
i've notice of the very low volume level from the built in speaker of the earliest Mac Pro ( i've one ) compared to the previous one (2008...i've one). Is this normal ?
Thanks in advance.

I can tell you right now, that's a complete waste of time! They're just gonna tell you it's "in spec."
It's a crumby speaker... deal with it. If you really care that much about the volume of the audio, you should just get a good pair of external speakers!

Sound is very low volume

I've done a search but can't seem to find any info re the sound volume on my bw G3. The sound out of both the front, built in speaker, and through the headphones, is very low volume output, almost but not quite muted. I've searched and adjusted the controls but to no avail. Could this be a hardware problem or software? There 'is' some movement when I adjust the volume slider but it takes the level from what would normally be 2 of 10 down to nothing. That is, there is no way for me to get the sound to levels that within normal limits. It's like the output is being blocked somehow but is still leaking through enough for me to make out the particular sound (song in this case) that I'm listening to.
Any help would be appreciated. It might not be worth puttiing any money into and I'd like to at least try.
Michael

Michael,
Sounds like you are ahead of the game on testing with headphones. External speakers would not make much of a difference without an amplifier.
"(is there another place to check sound output?)" If you had an AV output you could test sound out of that card. Finding a card might be cheaper than any repair bill and give you a definative answer on if their is a system software level problem.
Sound reading for your edification:
http://docs.info.apple.com/article.html?artnum=58764
http://docs.info.apple.com/article.html?artnum=31314
http://docs.info.apple.com/article.html?artnum=24718
http://www.info.apple.com/kbnum/n24503
These articles do not all address your model but give some perspective on software and hardware issues, including how just reseting the PRAM on some machines is the official Apple response.
If you go to the advanced search link at the top of the page and make a query for "no sound" you should get a response similar to this link:
Link
Be sure and include pre 1997 hardware.
Good luck.
Ji˜m

E105 very low volume

very low volume in toshiba satelite E105-S1802 IM APRECIATE ANYONE HELP ME

WInchesterAA wrote:Yeah.. everything passed.
I am asking whether the volume level in the speaker test in the Speaker Settings software is OK.

Songs with very low volume

Hi!!
(Excuse me for my bad english language.)
The songs are being exported with very low volume. I mixed all tracks to best use. I tried all the quality options, including no compression. I also tried with and without Normalize. What else can I try? What could be happening? Tks!

Hi stosfot,
Thanks for using Apple Support Communities. This article has some information on adjusting the master volume of a track that may help:
GarageBand '11: Adjust the project’s master volume
http://support.apple.com/kb/PH1997
Cheers,
- Ari

HP Pavilion g6-1d98dx has very low volume.

Hi there,
I have an
HP Pavilion g6-1d98dx with W7 Ultimate that suddenly has very low volume. I have tried rolling back the drivers, uninstalling them and the device itself.
I also tried that loudness equalization option, but it only makes it worse. It used to sound very good, but now it's horrible. Now I have to wear a headset just to listen to music! Any help would be greatly appreciated. Thanks!
This question was solved.
View Solution.

Hi @Kindakool
I understand that you are having trouble with the sound from your built in speakers. I am happy to help you with this.
You can start with the following page, even though you are getting some sound.
No Sound from the Speakers (Windows 7)
Or you can check the connections on your internal speakers for that you will need:
HP Pavilion G6 Notebook PC - Maintenance and Service Guide
From Microsoft's support website:
Automatically diagnose and fix Windows audio playback problems
If those do not work it is possible that there is a physical problem with the speakers themselves. At that point I would call in to our technical support at 800-474-6836. If you live outside the US/Canada Region, please click the link below to get the support number for your region.
http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html
Malygris1
I work on behalf of HP
Please click Accept as Solution if you feel my post solved your issue, it will help others find the solution.
Click Kudos Thumbs Up on the right to say “Thanks” for helping!

New HP2000 laptop plays very very low volume at the highest setting, please help me fix this!

new hp2000 laptop
very low volume
gone into all the settings i can see and cannot find a way to rectify this problem
help me hear my hulu / netflix / amazon prime / youtube
THANKS!

Hi, sorry to hear that you are having issues with your new notebook audio. I will be happy to help with the issue but first I will need to know the exact model number of the computer as well as the operating system you are using. To find the model number, please look on the bottom of the computer. You will see a white sticker. Here is where you will find the model number. If by chance you do not see the model number, please remove the battery and you will find it. I look forward to hearing from you.
Thanks for your time.
Click the “Kudos Thumbs Up" at the bottom of this post to say “Thanks” for helping!
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
W a t e r b o y 71
I work on behalf of HP

Very Low Volume Output - Audigy 2

Hi,
All of a sudden my Audigy 2 ZS card has very low volume. Tried different speakers, tried uninstall/reinstall, tried clean boot of XP, no luck. Also, there is faint crackling when I turn volume up but I believe it's only because speakers are fully cranked and there is hardly any sound coming out.
Any help would be appreciated. Thanks

I didn't have any place to test the card but I did replace it with another one. Unfortunately, the other card gives the same result - very low volume. I suppose this means there is a problem with the motherboard. Do you agree? Is there any other test I could do that might pinpoint the problem area?
Yes, I received a "reply" from Creative. It was a form email that said they received my message and would respond (usually) within 24 hours. That is the only message I received from them.

Microphone Very Low Volume

Hi
I have been using my new MXL USB 007 stereo microphone on Windows 7 Professional with clear quality audio for a while now.
On Monday 26 November 2012, I reformatted my PC laptop hard disk and installed Windows 8 Pro.
Now, the quality of the recorded audio is heavily subdued without the clear clarity I used to get. In other words, I am getting very low volume, even though the recording level is on 85 (I tried with 90 as well. 100 has way too much distortion).
As a test, I connected the same microphone to another one of my machines that still has Windows 7 Professional, and the audio result was excellent. So, it’s not the actual microphone.
I have checked the Windows 8 sound settings. It says the device is working properly. There is only the Levels to adjust and under the Advanced tab, I have 2 channel, 16 bit, 48 kHz, DVD quality - same as before on Windows 7.
Is there some setting or something else I should do on Windows 8 to get decent sound again?
Any ideas? Please help ....
Thank you.

I have reinstalled Windows 8 Pro twice, both times formatting the disk.
The first time, I connected the microphone immediately after the OS install.
The second time, I connected the microphone only after all Windows Updates and device drivers were applied.
In both cases, the problem of very low input volume remains.
I searched online, and found somebody else has the same problem with a different vendors microphone.
I quote from:
http://www.tomshardware.com/forum/1251-73-microphone-input
"I use Cakewalk for sound processing and have discovered that my Samson CO1U
microphone has almost no input strength under Windows 8. I have tweaked about everything I can imagine. Any ideas? "
On my machine, I looked at Device Manager and found:
From the above screenshot, it seems like the USBAUDIO.sys file is one of several being used.
Unless I am mistaken, all of the sound device driver files for the USB Audio CODEC are Microsoft files.
If so, can we please get a Windows Update on this issue?
Awaiting in anticipation ....

My iPhone 4 plays music at a low volume when connected to a car stereo

My iPhone 4 plays music at a low volume when connected to a car stereo either by fm transmitter or aux cable. The volume on the phone is full and the car stereo is full yet you can barely hear it. Anyone else had issues with this

I seem to remember someone several months ago having this same problem and I think it turned out to be the AUX cord.
FM transmitters tend to have low volume associated with them as well from my experience.

Apple TV3 airplay audio to other audio airplay devices with very very low volume!

TV3 airplay audio to other audio airplay devices abnormal,the other audio airplay devices received very very low audio volume,and the other audio airplay devices could support iphone normally,WHY? HELP ! HELP！HELP !
VERY VERY LOW AUDIO VOLUME!
I have two model audio airplay devices,they all meet the same problem!
LOOKING FORWARD TO　ＲＥＰＬＹ！

I found out that my current network situation is ATV3 connected to LAN with Powerline devices gives the problem described above. Changing to WiFi connection to the Router, solves the problem even with a lower speed.

Very low volume now?

Hi, i've only had my ipod touch for a week, so i'm still very much getting used to it. My problem is the very low & i mean very low sound when not useing headphones. I turn the volume all the way up, no good. But when i first got it the volume was pretty good ! I've tried all the settings but nothing makes it louder, any ideas what the problem could be? Thank you
Mo.

Hello, Welcome to Discussions.
I have a couple ideas
-Equalizer on the iPod Touch - Accessed via - Settings - iPod
-Sound Check via - Settings - iPod
-Volume Limit via - Settings - iPod
*un-sync the songs off and re-sync them back to the iPod Touch
*iPod touch and iPhone: Turning on/off and resetting
http://support.apple.com/kb/HT1430
Backing Up, updating, and restoring your iPhone and iPod touch software
http://support.apple.com/kb/HT1414
*Make an appointment at local Apple Store for further assistance
http://www.apple.com/uk/retail/

IPhone 3G v 3.0 very low volume in BMW

Similar Messages

Maybe you are looking for