Iphone 4 (4.2.1) panic error we are hanging here

Good Day
I am having an Iphone4 (16gb) factory unlocked phone bought from an apple store in canada and currently I am using it in Dubai; the apple id is configured with geographic location India ; it was working perfectly till my last OS upgrade to 4.2.1; after that it started giving reboot problems (showing apple logo); sometimes during a call its showing apple logo, then i need to press both home and sleep button together to start it; since last week it shows another error we are hanging here a panic message; (the screen becomes a dos based without any graphics); then again after pressing both sleep button and home button it comes back to normal screen; I was planning to go for factory reset; will it restore the previous os shipped with the phone? Today I heard 4.3 is released? if these problems are due to a bug with 4.2.1; will it be sorted out in 4.3?
Please guide me
Thanks in Advance
High Regards
Raneesh

Update;
My phone suddenly switched off itself and i can not turn it back on not even on recovery mode.
I guess at this point it is safe to say this phone is dead and i should return it to my service provider..

Similar Messages

Error when booting off install disk: "panic: We are hanging here . . ."

My iBook's working fine except it's very slow (3 years old), so I decided to reinstall the OS.
When I try loading off my original OS X installation disk, it boots to an error "panic: We are hanging here . . ."
If I stick the install CD into the iBook while it's on, it reads the CD fine and even offers to reboot off the CD for me. But when I reboot, I get the same panic error.
When I take the CD out, the iBook loads fine again.
So my computer still works, but I can't figure out a way to reinstall. Any ideas?
fyi- I tried Disk Utility on my HD and it passed verification.

Call Apple Support. They may be able to send you a replacement disc at nominal cost (much less than new). I think you'll need your computer's serial number so they can get the correct one.
How does the computer handle other CDs? There's the slight possibility it is the drive and not the CD.
The other thing to do is to try and troubleshoot why your computer is slowing down and at least not to have to immediately worry about getting a new CD. Here's a bunch of reading. However, I wouldn't blindly go running a bunch of utilities but to address things one by one. For example, one major slow down is an over-full hard drive and no utility will help with that.
[Mac Tune-up: 34 Software Speedups|http://www.macworld.com/article/49489/2006/02/softwarespeed.html]
[52 Ways to Speed Up OS X|http://www.imafish.co.uk/articles/post/articles/130/52-ways-to-speed-up-os-x>
[Tuning Mac OS X Performance|http://www.thexlab.com/faqs/performance.html]
[11 Ways to Optimize Your Mac's Performance|http://lowendmac.com/eubanks/07/0312.html]
[The Top 7 Free Utilities To Maintain A Mac.|http://mac360.com/index.php/mac360/comments/thetop_7_free_utilities_to_maintain_amac>
[Mac OS X: System maintenance|http://discussions.apple.com/thread.jspa?messageID=607640]
[Macintosh OS X Routine Maintenance|http://www.macattorney.com/ts.html#Anchor-31774]
[Kappy's Personal Suggestions for OS X Maintenance|http://discussions.apple.com/message.jspa?messageID=8230024#8230024 ]
[a brody's Topic: Myths of required versus not required maintenance for Mac OS X|http://discussions.apple.com/thread.jspa?threadID=1772235]
[Are the desktops cluttered with files and folders?|http://discussions.apple.com/thread.jspa?messageID=7668937#7668937]
Message was edited by: Limnos
Message was edited by: Limnos

Panic: We are hanging here... -- Wont boot after update..? Please help

Hey..
I installed this update last night, it said powerbook 15" security update. So i installed it as usual and then, worked for a bit after it was done. Then hit the shutdown button.
This morning i go to turn i on, and, It freezes, up. and Displays the following.
panic(cpu 0): Unable to find driver for this platform: "PowerBook5,4".
Latest stack backtrace for cpu 0:
Backtrace:
0x00083498 0x0008397c 0x00276EE4 ect....
Proceeding back via exception chain:
Exception state(sv=0x008c1000)
PC=0x00000000; MSR= ect ect.
Kernal Version:
Darwin Kernal Version 7.9.0:
Wed Mar 30 20:11:17 pst 2005; root:xnu-517.12.7.obj~1/RELEASE_PPC
No Debugger configured - dumping infomration
MSR=00001030
Lists the same information again
panic: We are hanging here...
It is a 15" powerbook g4. I tried taking out, / changing the ram, Booting holding S, holding shift. I cant get ti even turn on. Any help would be awesome..
Powerbook g4 1.5 15" Mac OS X (10.3.9) 2 gigs of ram

Hello may:
Welcome to Apple discussions.
Boot from your software install DVD and run repair disk from the disk utility.
Barry

HT1688 my phone got the computer looking screen that said, "Panic, we are just hanging here" I tried to reset it, but it just goes to the "connect to iTunes" screen and sticks there. It finally con to restore, now gives message 1611 "iPhone could not b

Just after updating Draw with Friends, my iPhone got the "Panic, just haning here" message. I tried to reset it and it got stuck on the screen with the usb connect to iTunes. When I connected to iTunes on my Mac, it kept giving an error message that the phone connected could not be restored because it was in recovery mode, recover then connect. The phone wouldn't recover... I finally got it to connect to iTunes by holding down the home and power buttons, connecting to computer and then let the power button off as soon as the apple appeared. It took all night to download the restore for the phone, then when I hit the restore iPhone button, it gets half way done and gives the message" The iPhone could not be restored. An unknown error occurred (14).

Read here > http://support.apple.com/kb/TS3694

I have a G5 with a brand new hard drive,when I try and install the os I get a panic we are hanging error. What can I do to load the os

I Get a panic we are hanging error when trying to install the os on a new hard drive on a G5

Yes, the hard drive needs to be formatted and OS X must then be installed.
Drive Partition and Format
1. Boot from your OS X Installer Disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu.
2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. SMART info will not be reported on external drives. Otherwise, click on the Partition tab in the DU main window.
3. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Click on the Options button, set the partition scheme to GUID then click on the OK button. Set the format type to Mac OS Extended (Journaled.) Click on the Apply button and wait until the process has completed.
4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
5. Set the format type to Mac OS Extended (Journaled.) Click on the Security button, check the button for Zero Data and click on OK to return to the Erase window.
6. Click on the Erase button. The format process can take up to several hours depending upon the drive size.
7. Quit Disk Utility and return to the installer. Proceed with the OS X installation.
It's only a lost cause when nothing else works.

HT4972 i cant update my iphone 3gs to a more newer ios? it says here error! and the phone flashes some connect to itunes.. an if i connct nothing happens.. help me.. the ipgone wont open . and work pls help me thank you!

i cant update my iphone 3gs to a more newer ios? it says here error! and the phone flashes some connect to itunes.. an if i connct nothing happens.. help me.. the ipgone wont open . and work pls help me thank you!

Hello AlexCornejo,
Thanks for using Apple Support Communities.
The screen you're seeing on your iPhone indicates it is in recovery mode. Now since the device is not appearing in iTunes on your PC, first follow the steps in this article:
iOS: Device not recognized in iTunes for Windows
http://support.apple.com/kb/TS1538
After following those steps, you should be able to restore your iPhone.
Take care,
Alex H.

I can't sync my iphone to itunes i get this error message "Iphone could not sync because the sync failed to start" Help? both my computer windows and my phone are on the current versions of ios and itunes

I can't sync my iphone to itunes i get this error message "Iphone could not sync because the sync failed to start" Help? both my computer windows and my phone are on the current versions of ios and itunes

Hello lenmin,
Thanks for using Apple Support Communities.
To help resolve this issue where you're repeatedly prompted to authorize with your Apple ID in iTunes when syncing, please follow the directions in the article below.
iTunes: Missing folder or incorrect permissions may prevent authorization - Apple Support
Have a great weekend,
Alex H.

My iPhone gets a "web server proxy error" connecting to wifi @ home

Ever since installing Comcast Xfinity with Motorola SB6121 and Apple Extreme 5th generation, my iPhone 4 gets a web server proxy error or similar message for any apps seeking to go online. My iPod Touch 3rd generation works as does my MacBook Pro.
I've reset the router, harangued Comcast (no help - it's your phone, sir), rebooted the iPhone, checked all my settings (VPN - what's that? it's not connected), Proxy in the VPN settings is set to off. The phone will show the signal and it will check Apple Mail but Safari, Google APP anything needing web access will either hang or give the proxy error message. Apple Customer Care said call Comcast, Comcast said call Apple & I'm surprised to find little help on the web.
Here's what I found to work on a MacForum sight from 2 years ago.
1.
Settings->WiFi->under choose a network, click the blue arrow (on the right of the network nameyou use)->DHCP
     *now check the IP address with the one on your iPod Touch or computer to see if they are in sequence
     *scroll down to HTTP Proxy & make sure it is off
     -> renew lease may work
It was the making sure the IP address was correct/in sequence which I moved to the STATIC tab and input all the same information (use a screen shot to remember it - home button and on/off button at the same time, it will store in your pictures folder) and give that a shot.
The problem appears to be where multiple machines or devices are using the same router. The iPhone 3GS assigned an IP Address in order of preference, therefore 192.175.1.1 and then 192.175.1.2 etc. The iPhone 4 will assign a strange IP address which the router will not accept. You therefore need to look at the other devices linked and see what number is next in the sequence. Then go to static on the top tab and type in the IP adress manually followed by the Subnet mask, router and DNS details. Once you have completed the info press the DHCP button and HTTP Proxy as off - this is important.
2.
This is how i fixed the wifi problem...(i used my mac)
So basicly I created a new WiFi hotspot on my iMac, then I connected my iphone to it and it WORKS!
1. open System Preferences (Apple -> System Preferences) and click Sharing.
2. select Internet Sharing at the left side.
3. Then check off AirPort.
4. Then creat a newtwork name, and password
5. VOILA! look at the Wifi connections on your iPhone and it should be there!
(IF YOU HAD ANY PROBLEMS GO TO THIS LINK..
http://maketecheasier.com/create-wif...s-x/2009/10/20
THIS SITE SHOWS YOU HOW TO SET IT UP)
3.
reset Network
Same problem, but none of the above worked for me. Finally went to Settings/ General/ Reset/ Reset network settings. Saw this in a different thread.
Hope these help.
Cheers,
cs

This has solved loads of people who have this issue and have used an alternate DNS setting. Below are instructions for both iPhone OTA and on you Mac
If you are getting the error message "Unable to check for update" when you try an OTA (over the air update)
Change DNS Servers
Settings -> Wi-Fi
Click the blue arrow on your connected network
Delete everything in DNS and replace it with 208.67.222.222, 208.67.220.220
Try again
If this works, you will probably want to remove the WiFi network using "Forget This Network" and then reconnect to it to get your original DNS servers back. Alternatively, make a note of the original DNS servers before deleting them and replace it after you are done.
If you are getting the error message "Unable to check for update" when you try through iTunes
On your Mac
Choose Apple menu > System Preferences, and then click Network.
Select the network connection service you want to use (such as Wi-Fi or Ethernet, unless you named it something else) from the list, and then click Advanced.
Click DNS, and then click Add at the bottom of the DNS Servers list. Enter the IPv4 address for the DNS server.
You can use OpenDNS
208.67.222.222
208.67.220.220
or
You can Google Public DNS if you want
8.8.8.8
8.8.4.4
I have actually repointed my routers DNS so all my devices now point to OpenDNS servers

Apple iPhone 4 stuck in Recovery Mode (Error 1611). Any Suggestions

My iPhone 4 (16 GB) is in recovery mode (or DFU mode), but it seems to be stuck in it. For the last two days it has been telling me to connect to iTunes and when I do it tells me, "iTunes has detected an iPhone in recovery mode. You must restore this iPhone it can be used with iTunes". So I press restore and it asks me if I wish to Restore and Update; I agreed. I attempted the restore, but something went wrong. It goes through the "extracting software" stage fine, but when it says "Preparing iPhone for restore", the screen flashes white for a half a second or so and then it tries to start over. iTunes then leaves me with this message, "The iPhone 'iPhone' could not be restored. An unknown error occured (1611)."
I have tried to get it out of Recovery Mode several times through YouTube tutorials and other websites, but when I attempt to do this, it will just go back to the "Connect to iTunes" screen. It will not respond to anything unless it is plugged into my laptop (I'm almost certain of this, I cannot be completley sure because the screen is just black if not connected). I have tried several different USB cords, re-installed iTunes and Apple programs on my computer and even made a new user account on my laptop. (I'm using Windows 7). This phone has never been Jailbroken and nothing wrong with it as far as I'm concerned, except the occasional time the home button would not respond.
Before this happened, everything was working fine. Earlier in the week I got the Zagg InvisibleShield applied to my iPhone and everything was working great. On the night before this happened, my battery was extremely low and I used the Apple wall charger to charge it for the night (the USB cord was torn though).
Any Suggestions Would Be Appreciated!

Here are Apple steps: http://support.apple.com/kb/TS3694#error1611
Make sure you have a perfect USB cable. Maybe try to charge the battery before proceeding again.
If you have Warranty or AppleCare Coverage, take iPhone to Apple for resolution.
Error 1611 has been associated with the iPhones inability to hold the Restore Mode (mode where iTunes writes to iPhone) this can be due to anything. Restore Mode does need a good functioning battery to proceed. You describe some vague battery issues.
If you do not take the iPhone to Apple for help, the next step would be battery replacement.

When I sync my iPhone with iTunes I get an error message that says "iTunes could not sync calendars to the iPhone because the sync server failed to sync the iPhone"

When I sync my iPhone with iTunes I get an error message that says "iTunes could not sync calendars to the iPhone because the sync server failed to sync the iPhone" How do I fix this?

I had the same problem. I found this site http://itprokb.blogspot.com/2010/10/itunes-could-not-sync-calendars-to.html
It worked for me. Good luck!

My macbook pro is connected to internet via my time capsule but my iPad and iPhone won't. it shows wifi connection to the time capsule but when i go on to the internet on the iPad or iPhone, it comes up with network error. can anyone help?

my macbook pro is connected to internet via my time capsule but my iPad and iPhone won't. it shows wifi connection to the time capsule but when i go on to the internet on the iPad or iPhone, it comes up with network error. can anyone help?

This can be caused by a number of issues.
Was everything working and then suddenly stopped??
Or is this a new clean setup and has never worked.
Do you have a cable modem which is not a router and the TC setup in bridge? That will cause it. The TC must be in router mode, ie dhcp and nat.
Check the IP the MBP gets including dns and gateway..
Then check the ipad/iphone.. post what IP dns and gateway (router in applespeak) they get.

TS1424 I am trying to update itunes so that I can sync my new iphone. I get a message Error 7(Windows Error 127). I have uninstalled all apple software and tried to reload with no luck. I have also cleaned my registry with software.

I am trying to update iTunes so that I can sync my new iPhone. I get a message Error 7 (Windows Error 127). I have uninstalled all Apple software and tried to reload with no luck. I have also cleaned my computer's registry with registry cleaning software. Even tried reloading operating system disk to fix errors. Any ideas?

Hello chathamcpa,
I found an article with steps you can take when you are getting Error 7 when opening iTunes. I recommend following the steps in this article:
iTunes for Windows: "Error 7" message when opening iTunes
http://support.apple.com/kb/ts3074
Thank you for using Apple Support Communities.
Best,
Sheila M.

Hello everyone, I am trying to restore my iPhone 4s and every time I try restoring it, it always goes to about 75% of the process then it says the iphone could not restore because of error 1. This is not error -1 it is error 1.

Hello everyone, I am trying to restore my iPhone 4s and every time I try restoring it, it always goes to about 75% of the process then it says the iphone could not restore because of error 1. This is not error -1 it is error 1. I reserached this error and it said to make sure I have the latest version of iTunes, i do, To make sure i have a security software updated, i do, and ive done everything it tells me to do yet it wont let me restore my iphone. Before I tried restoring it, it was working perfectly fine besides the battery which i have just replaced yesterday. Ive tried restoring it in two different computers with two different cables but still no luck. I found this phone at a park and it was working perfectly fine until i tried restoring it. I have no idea what to do now. I appreciate your guyses help!

This error generally indicates a hardware failure. Bring the phone to Apple for evaluation.

Mountain Lion 10.8.4-Cisco Connect-shutdowns kernel panic error-EA6500

I have:
- Mac Mountain Lion OS X 10.8.4
- EA6500 with the latests updates (firmware..) all downloaded from Linksys web
When I install Cisco Connect to setup a USB printer, the software has some kind of conflict with OS X 10.8.4 and the system has unexpected & repentine shutdowns with a restart shutdown panic error report.
If I unistall Cisco Connect the problem doesn´t happen again
After checking all available guides and software, there is no way to solve the issue. I also chat with Linksys support and they have no idea how solve it.
It is for sure a problem of Cisco Connect software compatibility with OS X 10.8.4.
Please, some solution from Linksys or a workaround with Mac terminal commands?
DON´T INSTALL CISCO CONNECT SOFTWARE TILL ISSUE SOLVED!!

Cisco Connect would not work with a router using a Linksys Smart Wifi firmware. Also, VUSB is not going to work with MAC OS 10.8 yet. Hopefully Linksys would release an update that would support MAC 10.8 on VUSB.
Connecting a USB printer through the Cisco VUSB software on a Mac® computer
Connecting a USB printer through the Cisco VUSB software on a Windows-based computer

Multiple kernel panic errors after upgrading to snow leopard 10.6.8 on my MacBook Pro.

After upgrading to 10.6.8, I almost immediately began experiencing multiple random kernel panic errors. I reinstalled the operating system that came with my notebook from the cd (10.6?) and the problem went away. I upgraded again to 10.6.8 and again began experiencing the same error. I have since gone back and installed the operating syatem from the cd and then upgraded to 10.6.7. I have not had a single kernel panic error since, but I would like to upgrade to 10.6.8 so that I can install Lion when it is avaialable. Any thoughts as to how I can do this without experiencing all of the accompanying kernel panic errors?

Thank you. The log is below:
Anonymous UUID:                    CC4821C8-35CD-469C-BE4C-98F1DE35B903
Sun Jun 26 21:18:00 2011
Machine-check capabilities (cpu 3) 0x0000000000000c09:
family: 6 model: 37 stepping: 2 microcode: 9
Intel(R) Core(TM) i5 CPU       M 540 @ 2.53GHz
9 error-reporting banks
threshold-based error status present
extended corrected memory error handling present
Machine-check status 0x0000000000000004:
machine-check in progress
MCA error-reporting registers:
IA32_MC0_STATUS(0x401): 0x0000000000000800 invalid
IA32_MC1_STATUS(0x405): 0x0000000000000000 invalid
IA32_MC2_STATUS(0x409): 0xb200000000020005 valid
MCA error code:            0x0005
Model specific error code: 0x0002
Other information:         0x00000000
Threshold-based status:    No tracking
Status bits:
   Processor context corrupt
   Error enabled
   Uncorrected error
IA32_MC3_STATUS(0x40d): 0x0000000000000000 invalid
IA32_MC4_STATUS(0x411): 0x0000000000000000 invalid
IA32_MC5_STATUS(0x415): 0x0000000000000000 invalid
IA32_MC6_STATUS(0x419): 0x0000000000000000 invalid
IA32_MC7_STATUS(0x41d): 0x0000000000000000 invalid
Package 0 logged:
IA32_MC8_STATUS(0x421): 0x0000000000000000 invalid
panic(cpu 3 caller 0x2aaf41): Machine Check at 0x002b1eb9, thread:0x85833d4, trapno:0x12, err:0x0,registers:
CR0: 0x8001003b, CR2: 0x02282868, CR3: 0x00100000, CR4: 0x00000660
EAX: 0x000100de, EBX: 0x00000630, ECX: 0x00000000, EDX: 0x7fffffff
ESP: 0x5c82bd28, EBP: 0x5c82bd28, ESI: 0x00000000, EDI: 0x5501e0a8
EFL: 0x00000002, EIP: 0x002b1eb9
Backtrace (CPU 3), Frame : Return Address (4 potential args on stack)
0x550b8fb8 : 0x21b837 (0x5dd7fc 0x550b8fec 0x223ce1 0x0)
0x550b9008 : 0x2aaf41 (0x59dfe4 0x59e0d1 0x2b1eb9 0x85833d4)
0x550b90f8 : 0x2a29f2 (0x1 0x3b40c858 0xfffd9085 0x83077fff)
0x5c82bd28 : 0x2b2124 (0x32 0x0 0x0 0x0)
0x5c82bd48 : 0x11f1db7 (0x5501e0a8 0xffffffff 0x7fffffff 0xffffffff)
0x5c82be28 : 0x11f3850 (0xffffffff 0x7fffffff 0x0 0x0)
0x5c82bf28 : 0x2ad0c5 (0xffffffff 0x7fffffff 0x10 0x202)
0x5c82bf48 : 0x225bba (0x0 0x4ffad2b2 0xd5 0x5502d488)
0x5c82bfa8 : 0x22810b (0x85833d4 0x2280f4 0x0 0x8c57764)
0x5c82bfc8 : 0x2a179c (0x0 0xffffffff 0x10 0xa1f1064)
      Kernel Extensions in backtrace (with dependencies):
         com.apple.driver.AppleIntelCPUPowerManagement(142.6.0)@0x11f0000->0x1213fff
BSD process name corresponding to current thread: kernel_task
Mac OS version:
10K540
Kernel version:
Darwin Kernel Version 10.8.0: Tue Jun 7 16:33:36 PDT 2011; root:xnu-1504.15.3~1/RELEASE_I386
System model name: MacBookPro6,2 (Mac-F22586C8)
System uptime in nanoseconds: 916750825314
unloaded kexts:
com.apple.driver.AppleUSBUHCI    4.2.0 (addr 0x142d000, size 0x65536) - last unloaded 138176310496
loaded kexts:
com.Symantec.kext.SAVAPComm    11.0.6 - last loaded 30941770731
com.apple.driver.AppleHWSensor    1.9.3d0
com.apple.filesystems.autofs    2.1.0
com.apple.driver.AGPM    100.12.31
com.apple.filesystems.ntfs    3.4
com.apple.driver.AppleMikeyHIDDriver    1.2.0
com.apple.driver.AppleMikeyDriver    2.0.5f13
com.apple.driver.AppleUpstreamUserClient    3.5.7
com.apple.driver.AppleMCCSControl    1.0.20
com.apple.driver.AppleHDA    2.0.5f13
com.apple.driver.AudioAUUC    1.57
com.apple.driver.AppleIntelHDGraphics    6.3.6
com.apple.driver.AppleIntelHDGraphicsFB    6.3.6
com.apple.driver.SMCMotionSensor    3.0.1d2
com.apple.Dont_Steal_Mac_OS_X    7.0.0
com.apple.driver.AudioIPCDriver    1.1.6
com.apple.driver.ACPI_SMC_PlatformPlugin    4.7.0a1
com.apple.GeForce    6.3.6
com.apple.driver.AppleGraphicsControl    2.10.6
com.apple.driver.AppleLPC    1.5.1
com.apple.kext.AppleSMCLMU    1.5.2d10
com.apple.driver.AppleUSBTCButtons    201.6
com.apple.driver.AppleUSBCardReader    2.6.1
com.apple.driver.AppleIRController    303.8
com.apple.driver.AppleUSBTCKeyboard    201.6
com.apple.BootCache    31.1
com.apple.AppleFSCompression.AppleFSCompressionTypeZlib    1.0.0d1
com.apple.iokit.SCSITaskUserClient    2.6.8
com.apple.iokit.IOAHCIBlockStorage    1.6.4
com.apple.driver.AppleUSBHub    4.2.4
com.apple.driver.AppleFWOHCI    4.7.3
com.apple.driver.AirPortBrcm43224    428.42.4
com.apple.iokit.AppleBCM5701Ethernet    3.0.5b8
com.apple.driver.AppleEFINVRAM    1.4.0
com.apple.driver.AppleSmartBatteryManager    160.0.0
com.apple.driver.AppleAHCIPort    2.1.7
com.apple.driver.AppleUSBEHCI    4.2.4
com.apple.driver.AppleACPIButtons    1.3.6
com.apple.driver.AppleRTC    1.3.1
com.apple.driver.AppleHPET    1.5
com.apple.driver.AppleSMBIOS    1.7
com.apple.driver.AppleACPIEC    1.3.6
com.apple.driver.AppleAPIC    1.4
com.apple.driver.AppleIntelCPUPowerManagementClient    142.6.0
com.apple.security.sandbox    1
com.apple.security.quarantine    0
com.apple.nke.applicationfirewall    2.1.12
com.apple.driver.AppleIntelCPUPowerManagement    142.6.0
com.apple.driver.AppleProfileReadCounterAction    17
com.apple.driver.DspFuncLib    2.0.5f13
com.apple.driver.AppleProfileTimestampAction    10
com.apple.driver.AppleProfileThreadInfoAction    14
com.apple.driver.AppleProfileRegisterStateAction    10
com.apple.driver.AppleProfileKEventAction    10
com.apple.driver.AppleProfileCallstackAction    20
com.apple.driver.AppleSMBusController    1.0.10d0
com.apple.iokit.IOFireWireIP    2.0.3
com.apple.iokit.IOSurface    74.2
com.apple.iokit.IOBluetoothSerialManager    2.4.5f3
com.apple.iokit.IOSerialFamily    10.0.3
com.apple.iokit.IOAudioFamily    1.8.3fc2
com.apple.kext.OSvKernDSPLib    1.3
com.apple.driver.AppleHDAController    2.0.5f13
com.apple.iokit.IOHDAFamily    2.0.5f13
com.apple.iokit.AppleProfileFamily    41
com.apple.driver.IOPlatformPluginFamily    4.7.0a1
com.apple.driver.AppleSMBusPCI    1.0.10d0
com.apple.driver.AppleBacklightExpert    1.0.1
com.apple.driver.AppleSMC    3.1.0d5
com.apple.nvidia.nv50hal    6.3.6
com.apple.NVDAResman    6.3.6
com.apple.iokit.IONDRVSupport    2.2
com.apple.iokit.IOGraphicsFamily    2.2
com.apple.driver.BroadcomUSBBluetoothHCIController    2.4.5f3
com.apple.driver.AppleUSBBluetoothHCIController    2.4.5f3
com.apple.iokit.IOBluetoothFamily    2.4.5f3
com.apple.iokit.IOSCSIBlockCommandsDevice    2.6.8
com.apple.iokit.IOUSBMassStorageClass    2.6.7
com.apple.driver.AppleUSBMultitouch    207.7
com.apple.iokit.IOUSBHIDDriver    4.2.0
com.apple.driver.AppleUSBMergeNub    4.2.4
com.apple.driver.AppleUSBComposite    3.9.0
com.apple.iokit.IOSCSIMultimediaCommandsDevice    2.6.8
com.apple.iokit.IOBDStorageFamily    1.6
com.apple.iokit.IODVDStorageFamily    1.6
com.apple.iokit.IOCDStorageFamily    1.6.1
com.apple.driver.XsanFilter    402.1
com.apple.iokit.IOAHCISerialATAPI    1.2.6
com.apple.iokit.IOSCSIArchitectureModelFamily    2.6.8
com.apple.iokit.IOFireWireFamily    4.2.6
com.apple.iokit.IOUSBUserClient    4.2.4
com.apple.iokit.IO80211Family    320.1
com.apple.iokit.IONetworkingFamily    1.10
com.apple.iokit.IOAHCIFamily    2.0.6
com.apple.iokit.IOUSBFamily    4.2.4
com.apple.driver.AppleEFIRuntime    1.4.0
com.apple.iokit.IOHIDFamily    1.6.6
com.apple.iokit.IOSMBusFamily    1.1
com.apple.kext.AppleMatch    1.0.0d1
com.apple.security.TMSafetyNet    6
com.apple.driver.DiskImages    289.1
com.apple.iokit.IOStorageFamily    1.6.3
com.apple.driver.AppleACPIPlatform    1.3.6
com.apple.iokit.IOPCIFamily    2.6.5
com.apple.iokit.IOACPIFamily    1.3.0
System Profile:
Model: MacBookPro6,2, BootROM MBP61.0057.B0C, 2 processors, Intel Core i5, 2.53 GHz, 4 GB, SMC 1.58f15
Graphics: NVIDIA GeForce GT 330M, NVIDIA GeForce GT 330M, PCIe, 256 MB
Graphics: Intel HD Graphics, Intel HD Graphics, Built-In, 288 MB
Memory Module: global_name
AirPort: spairport_wireless_card_type_airport_extreme (0x14E4, 0x93), Broadcom BCM43xx 1.0 (5.10.131.36.9)
Bluetooth: Version 2.4.0f1, 2 service, 19 devices, 1 incoming serial ports
Network Service: AirPort, AirPort, en1
Serial ATA Device: ST9500325ASG, 465.76 GB
Serial ATA Device: MATSHITADVD-R   UJ-898
USB Device: Hub, 0x0424 (SMSC), 0x2514, 0xfd100000
USB Device: Built-in iSight, 0x05ac (Apple Inc.), 0x8507, 0xfd110000
USB Device: IR Receiver, 0x05ac (Apple Inc.), 0x8242, 0xfd120000
USB Device: Hub, 0x0424 (SMSC), 0x2514, 0xfa100000
USB Device: Apple Internal Keyboard / Trackpad, 0x05ac (Apple Inc.), 0x0236, 0xfa120000
USB Device: BRCM2070 Hub, 0x0a5c (Broadcom Corp.), 0x4500, 0xfa110000
USB Device: Bluetooth USB Host Controller, 0x05ac (Apple Inc.), 0x8218, 0xfa113000
USB Device: Internal Memory Card Reader, 0x05ac (Apple Inc.), 0x8403, 0xfa130000

Iphone 4 (4.2.1) panic error we are hanging here

Similar Messages

Maybe you are looking for